TS78M00A series 3-Terminal Medium Current Positive Voltage Regulator Pin assignment: 1. Input 2. Ground 3. Output (Heatsink surface connected to Pin 2) Voltage Range 5V to 24V Output Current up to 0.5A General Description The TS78M00A Series positive voltage regulators are identical to the popular TS7800 Series devices, except that they are specified for only half the output current. Like the TS7800 devices, the TS78M00A Series 3-Terminal regulators are intended for local, on-card voltage regulation. Internal current limiting, thermal shutdown circuitry and safe-area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions. Maximum output current with adequate heatsink is 500mA This series is offered in 3-pin TO-220, TO-252 package. Features Standard Application Output current up to 0.5A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 2% tolerance Ordering Information Part No. TS78MxxACZ TS78MxxACP Operating Temp. (Ambient) Package TO-220 -20 ~ +85oC TO-252 Note: Where xx denotes voltage option. A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Absolute Maximum Rating Input Voltage Vin * 35 V Input Voltage Vin ** 40 V TO-220 Without heatsink 2 TO-220 Pt *** 15 TO-252 Without heatsink 1 TJ 0 ~ +150 o C -65 ~ +150 o C Power Dissipation Operating Junction Temperature Range Storage Temperature Range Note : TSTG * TS78M05A to TS78M18A ** TS78M24A *** Follow the derating curve TS78M00A series 1-9 2003/12 rev. B W TS78M05A Electrical Characteristics (Vin=10V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 4.90 5 5.10 4.80 5 5.20 -- 3 50 5mA≤Iout≤500mA -- 20 100 5mA≤Iout≤200mA o Tj=25 C Output voltage Vout 7.5V≤Vin≤20V, 5mA≤Iout≤350mA, PD≤5W Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage Vdrop Io peak ∆Vout/ ∆Tj Tj=25 oC o Tj=25 C 7.5V≤Vin≤25V, Io=200mA Unit V mV -- 10 50 o Iout=0, Tj=25 C -- 3 6 7.5V≤Vin≤25V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 40 -- uV f=120Hz, 8V≤Vin≤18V 62 80 -- dB -- 2 -- V Tj=25 C -- 0.7 -- A Iout=5mA, 0 oC≤Tj≤125 oC -- -0.2 -- 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C o mA mV/ o C TS78M06A Electrical Characteristics (Vin=11V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 5.88 6 6.12 5.76 6 6.24 -- 3 50 5mA≤Iout≤500mA -- 20 120 5mA≤Iout≤200mA -- 10 60 o Iout=0, Tj=25 C -- 3 6 8.5V≤Vin≤25V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 45 -- uV f=120Hz, 9V≤Vin≤19V 59 80 -- dB o Tj=25 C Output Voltage Vout 8.5V≤Vin≤21V, 5mA≤Iout≤350mA, PD≤5W Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Vdrop Ios Io peak Tj=25 oC o Tj=25 C 8.5V≤Vin≤25V, Io=200mA 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C V mV mA -- 2 -- V o -- 50 -- mA o -- 0.7 -- Tj=25 C Tj=25 C Temperature Coefficient of ∆Vout/ ∆Tj Iout=5mA, 0 oC≤Tj≤125 oC --0.2 -Output Voltage z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. z This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS78M00A series Unit 2-9 2003/12 rev. B A mV/ o C TS78M08A Electrical Characteristics (Vin=14V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 7.84 8 8.16 7.68 8 8.32 -- 6 50 5mA≤Iout≤500mA -- 25 160 5mA≤Iout≤200mA -- 10 80 o Iout=0, Tj=25 C -- 3 6 10.5V≤Vin≤25V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 52 -- uV f=120Hz, 11V≤Vin≤21V 56 80 -- dB o Tj=25 C Output Voltage Vout 10.5V≤Vin≤23V, 5mA≤Iout≤350mA, PD≤5W Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vdrop Ios Io peak ∆Vout/ ∆Tj Tj=25 oC o Tj=25 C 10.5V≤Vin≤25V, Io=200mA 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C Unit V mV mA -- 2 -- V o -- 50 -- mA o -- 0.7 -- Tj=25 C Tj=25 C Iout=5mA, 0 oC≤Tj≤125 oC -- -0.2 -- A mV/ o C TS78M09A Electrical Characteristics (Vin=15V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max o Tj=25 C Output Voltage Vout 11.5V≤Vin≤23V, 5mA≤Iout≤350mA, PD≤5W Line Regulation REGline Tj=25 oC Load Regulation REGload Tj=25 oC Quiescent Current Quiescent Current Change Iq ∆Iq 11.5V≤Vin≤26V, Io=200mA 5mA≤Iout≤500mA 5mA≤Iout≤200mA Iout=0, Tj=25 oC 11.5V≤Vin≤26V 5mA≤Iout≤350mA 10Hz≤f≤100KHz, Tj=25 oC Output Noise Voltage Vn Ripple Rejection Ratio RR f=120Hz, 12V≤Vin≤22V Vdrop Iout=350mA, Tj=25 oC Voltage Drop Output Short Circuit Current Peak Output Current Ios Tj=25 oC Io peak Tj=25 oC Temperature Coefficient of ∆Vout/ ∆Tj Iout=5mA, 0 oC≤Tj≤125 oC Output Voltage z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. z This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS78M00A series 3-9 2003/12 rev. B Unit TS78M10A Electrical Characteristics (Vin=16V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 9.80 10 10.20 9.60 10 10.40 -- 8 50 5mA≤Iout≤500mA -- 25 200 5mA≤Iout≤200mA -- 10 100 o Iout=0, Tj=25 C -- 3 6 12.5V≤Vin≤28V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 70 -- uV f=120Hz, 13V≤Vin≤23V 55 80 -- dB o Tj=25 C Output Voltage Vout 12.5V≤Vin≤25V, 5mA≤Iout≤350mA, PD≤5W Line Regulation Load Regulation Quiescent Current Quiescent Current Change REGline REGload Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vdrop Ios Io peak ∆Vout/ ∆Tj Tj=25 oC o Tj=25 C 12.5V≤Vin≤28V, Io=200mA 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C Unit V mV mA -- 2 -- V o -- 50 -- mA o -- 0.7 -- Tj=25 C Tj=25 C Iout=5mA, 0 oC≤Tj≤125 oC -- -0.3 -- A mV/ o C TS78M12A Electrical Characteristics (Vin=19V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 11.76 12 12.24 11.52 12 12.48 -- 8 50 5mA≤Iout≤500mA -- 25 240 0mA≤Iout≤200mA -- 10 120 Tj=25 C, Iout=0 -- 3 6 14.5V≤Vin≤30V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 75 -- uV f=120Hz, 15V≤Vin≤25V 55 80 -- dB -- 2 -- V o Tj=25 C Output Voltage Vout 14.5V≤Vin≤27V, 5mA≤Iout≤350mA, PD ≤5W Line Regulation REGline Tj=25 oC Load Regulation REGload Tj=25 oC Quiescent Current Quiescent Current Change Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Temperature Coefficient of Vdrop 14.5V≤Vin≤30V, Io=200mA o 5mA≤Iout≤200mA o o Iout=350mA, Tj=25 C o V mV mA Ios Tj=25 C -- 50 -- mA Io peak Tj=25 oC -- 0.7 -- A Iout=5mA, 0 oC≤Tj≤125 oC -- -0.3 -- ∆Vout/ ∆Tj Output Voltage z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. z This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS78M00A series Unit 4-9 2003/12 rev. B mV/ o C TS78M15A Electrical Characteristics (Vin=23V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 14.70 15 15.30 14.40 15 15.60 -- 8 50 5mA≤Iout≤500mA -- 25 300 5mA≤Iout≤200mA -- 10 150 Tj=25 C, Iout=0 -- 3 6 17.5V≤Vin≤30V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 90 -- uV f=120Hz, 18V≤Vin≤28V 54 70 -- dB o Tj=25 C Output Voltage Vout 17.5V≤Vin≤30V, 5mA≤Iout≤350mA, PD ≤5W Line Regulation REGline Tj=25 17.5V≤Vin≤30V, o Io=200mA Load Regulation REGload o Quiescent Current Quiescent Current Change Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vdrop Ios Io peak ∆Vout/ ∆Tj C Tj=25 C o 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C Unit V mV mA -- 2 -- V o -- 50 -- mA o -- 0.7 -- Tj=25 C Tj=25 C Iout=5mA, 0 oC≤Tj≤125 oC -- -0.3 -- A mV/ o C TS78M18A Electrical Characteristics (Vin=27V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 17.64 18 18.36 17.28 18 18.72 -- 8 50 5mA≤Iout≤500mA -- 25 360 5mA≤Iout≤200mA o Tj=25 C Output Voltage Vout 21V≤Vin≤33V, 5mA≤Iout≤350mA, PD ≤5W Line Regulation REGline Tj=25 oC Load Regulation REGload Tj=25 oC Quiescent Current Quiescent Current Change Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Temperature Coefficient of Vdrop 21V≤Vin≤33V, Io=200mA V mV -- 10 180 o Tj=25 C, Iout=0 -- 3 6 21V≤Vin≤33V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 110 -- uV f=120Hz, 21V≤Vin≤31V 54 70 -- dB -- 2 -- V 5mA≤Iout≤350nA o o Iout=350mA, Tj=25 C o mA Ios Tj=25 C -- 50 -- mA Io peak Tj=25 oC -- 0.7 -- A Iout=5mA, 0 oC≤Tj≤125 oC -- -0.5 -- ∆Vout/ ∆Tj Output Voltage z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. z This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS78M00A series Unit 5-9 2003/12 rev. B mV/ o C TS78M24A Electrical Characteristics (Vin=33V, Iout=350mA, 0 oC≤Tj≤125 oC, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Conditions Min Typ Max 23.52 24 24.48 22.04 24 25.96 -- 10 50 5mA≤Iout≤500mA -- 30 480 5mA≤Iout≤200mA -- 10 240 o Iout=0, Tj=25 C -- 4 7 27V≤Vin≤38V -- -- 0.8 -- -- 0.5 10Hz≤f≤100KHz, Tj=25 C -- 170 -- uV f=120Hz, 27V≤Vin≤37V 50 70 -- dB o Tj=25 C Output Voltage Vout 27V≤Vin≤38V, 5mA≤Iout≤350mA, PD ≤5W Line Regulation REGline Tj=25 oC Load Regulation REGload Tj=25 oC Quiescent Current Quiescent Current Change Iq ∆Iq Output Noise Voltage Vn Ripple Rejection Ratio RR Voltage Drop Output Short Circuit Current Peak Output Current Vdrop Ios Io peak 27V≤Vin≤38V, Io=200mA 5mA≤Iout≤350mA o o Iout=350mA, Tj=25 C V mV mA -- 2 -- V o -- 50 -- mA o -- 0.7 -- Tj=25 C Tj=25 C Temperature Coefficient of ∆Vout/ ∆Tj Iout=5mA, 0 oC≤Tj≤125 oC --0.5 -Output Voltage z Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. z This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS78M00A series Unit 6-9 2003/12 rev. B A mV/ o C Electrical Characteristics Curve FIGURE 1 - Worst Case Power Dissipation v.s. Ambient Temperature FIGURE 2 - Peak Output Current v.s. Dropout Voltage FIGURE 3 – Quiescent Current v.s. Input Voltage FIGURE 4 –Dropout Voltage v.s. Junction Temperature FIGURE 5 – Quiescent Current v.s. Output Current FIGURE 6 – TO-252 Thermal Resistance and Pd(max) v.s. P.C.B Copper Length TS78M00A series 7-9 2003/12 rev. B Electrical Characteristics Curve FIGURE 7 – Ripple Rejection v.s. Frequency TS78M00A series FIGURE 8 – Ripple Rejection v.s. Output Voltage 8-9 2003/12 rev. B TO-220 Mechanical Drawing K B A L DIM A B C D E F G H I J MIN 10.000 3.240 2.440 0.381 2.345 4.690 12.700 8.382 14.224 MAX 10.500 4.440 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 MIN 0.394 0.128 0.096 0.015 0.092 0.092 0.500 0.330 0.560 MAX 0.413 0.175 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 K L M N O P 3.556 0.508 27.700 2.032 0.255 5.842 4.826 1.397 29.620 2.921 0.610 6.858 0.140 0.020 1.060 0.080 0.010 0.230 0.190 0.055 1.230 0.115 0.024 0.270 C P J I M D H F G O E N TO-220 DIMENSION MILLIMETERS INCHES TO-252 Mechanical Drawing E J A A TO-252 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 6.570 6.840 0.259 0.269 B C D E F G H I J 9.250 0.550 2.560 2.300 0.490 1.460 0.520 5.340 1.460 F DIM I B G D TS78M00A series C H 9-9 10.400 0.700 2.670 2.390 0.570 1.580 0.570 5.550 1.640 0.364 0.022 0.101 0.090 0.019 0.057 0.020 0.210 0.057 2003/12 rev. B 0.409 0.028 0.105 0.094 0.022 0.062 0.022 0.219 0.065