TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TO-220 ITO-220 TO-263 2 (D PAK) Pin Definition: 1. Input 2. Ground (tab) 3. Output General Description These voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsink they can deliver output currents up to 1 ampere. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. Features Standard Application Circuit ● Output Voltage Range 5 to 24V ● Output current up to 1.5A ● No external components required ● Internal thermal overload protection ● Internal short-circuit current limiting ● Output transistor safe-area compensation ● Output voltage offered in 4% tolerance A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Ordering Information Part No. Package Packing TS78xxBCZ C0 TO-220 50pcs / Tube TS78xxBCI C0 ITO-220 50pcs / Tube TS78xxBCM RN TO-263 800pcs / 13” Reel Note: Where xx denote voltage option Absolute Maximum Rating (Ta = 25 oC unless otherwise noted) Parameter Symbol Limit Unit Input Voltage VIN* 35 V Input Voltage VIN** 40 V PD Internal Limited Power Dissipation Operating Junction Temperature TJ Storage Temperature Range Note: * TS7805B to TS7818B ** TS7824B *** Follow the derating curve TSTG 1/12 W 0~+125 o -65~+150 o C C Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TS7805B Electrical Characteristics o o (Vin=10V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj 7.5V≤Vin≤20V, 10mA≤Iout≤1.5A, PD≤15W 7.5V≤Vin≤25V o Tj=25 C 8V≤Vin≤12V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 7.5V≤Vin≤25V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 8V≤Vin≤18V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C o o Iout=10mA, 0 C≤Tj≤125 C Min Typ Max Unit 4.80 5 5.20 4.75 5 5.25 --------62 ----- 3 1 15 5 4.2 --40 78 2 17 750 2.2 100 50 100 50 8 1.3 0.5 ------- µV dB V mΩ mA A -- -0.6 -- mV/ C Unit V mV mA o TS7806B Electrical Characteristics o o (Vin=11V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C 8.5V≤Vin≤21V, 10mA≤Iout≤1.5A, PD≤15W 8.5V≤Vin≤25V o Tj=25 C 9V≤Vin≤13V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 8.5V≤Vin≤25V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 9V≤Vin≤19V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C 5.75 6 6.25 5.7 6 6.3 --------59 ----- 5 1.5 14 4 4.3 --45 75 2 19 550 2.2 120 60 120 60 8 1.3 0.5 ------- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=10mA, 0 C≤Tj≤125 C --0.7 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TS7808B Electrical Characteristics o o Vin=14V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj 10.5V≤Vin≤23V, 10mA≤Iout≤1.5A, PD≤15W 10.5V≤Vin≤25V o Tj=25 C 11V≤Vin≤17V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 10.5V≤Vin≤25V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 11V≤Vin≤21V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C o o Iout=10mA, 0 C≤Tj≤125 C Min Typ Max Unit 7.69 8 8.32 7.61 8 8.40 --------56 ----- 6 2 12 4 4.3 --52 72 2 16 450 2.2 160 80 160 80 8 1 0.5 ------- µV dB V mΩ mA A -- -0.8 -- mV/ C Unit V mV mA o TS7809B Electrical Characteristics o o (Vin=15V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C 11.5V≤Vin≤23V, 10mA≤Iout≤1.5A, PD≤15W 11.5V≤Vin≤26V o Tj=25 C 12V≤Vin≤17V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 11.5V≤Vin≤26V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 12V≤Vin≤22V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C 8.65 9 9.36 8.57 9 9.45 --------55 ----- 6 2 12 4 4.3 --52 72 2 16 450 2.2 180 90 180 90 8 1 0.5 ------- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 3/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TS7810B Electrical Characteristics o o Vin=16V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj 12.5V≤Vin≤25V, 10mA≤Iout≤1.5A, PD≤15W 12.5V≤Vin≤28V o Tj=25 C 13V≤Vin≤17V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 12.5V≤Vin≤28V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 13V≤Vin≤23V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C o o Iout=10mA, 0 C≤Tj≤125 C Min Typ Max Unit 9.6 10 10.4 9.5 10 10.5 --------55 ----- 7 2 12 4 4.3 --70 71 2 18 400 2.2 200 100 200 100 8 1 0.5 ------- µV dB V mΩ mA A -- -1 -- mV/ C Unit V mV mA o TS7812B Electrical Characteristics o o (Vin=19V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C 14.5V≤Vin≤27V, 10mA≤Iout≤1.5A, PD ≤15W 14.5V≤Vin≤30V o Tj=25 C 15V≤Vin≤19V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 14.5V≤Vin≤30V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 15V≤Vin≤25V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C 11.53 12 12.48 11.42 12 12.60 --------55 ----- 10 3 12 4 4.3 --75 71 2 18 350 2.2 240 120 240 120 8 1 0.5 ------- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 4/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TS7815B Electrical Characteristics o o Vin=23V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation REGload Quiescent Current Iq Quiescent Current Change ΔIq Output Noise Voltage Ripple Rejection Ratio Voltage Drop Output Resistance Output Short Circuit Current Peak Output Current Temperature Coefficient of Output Voltage Vn RR Vdrop Rout Ios Io peak ΔVout/ ΔTj 17.5V≤Vin≤30V, 10mA≤Iout≤1.5A, PD ≤15W 17.5V≤Vin≤30V o Tj=25 C 18V≤Vin≤22V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 17.5V≤Vin≤30V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 18V≤Vin≤28V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C o o Iout=10mA, 0 C≤Tj≤125 C Min Typ Max Unit 14.42 15 15.60 14.28 15 15.75 --------54 ----- 12 3 12 4 4.3 --90 70 2 19 230 2.2 300 150 300 150 8 1 0.5 ------- µV dB V mΩ mA A -- -1 -- mV/ C Unit V mV mA o TS7818B Electrical Characteristics o o (Vin=24V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition Min Typ Max Tj=25 C 21V≤Vin≤33V, 10mA≤Iout≤1.5A, PD ≤15W 21V≤Vin≤33V o Tj=25 C 22V≤Vin≤26V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Tj=25 C, Iout=0 21V≤Vin≤33V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 21V≤Vin≤31V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C 17.30 18 18.72 17.14 18 18.90 --------54 ----- 15 5 12 4 4.5 --110 70 2 22 200 2.2 360 180 360 180 8 1 0.5 ------- o Output Voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq V mV mA Output Noise Voltage Vn uV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=10mA, 0 C≤Tj≤125 C --1 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 5/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TS7824B Electrical Characteristics o o Vin=33V, Iout=500mA, 0 C≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) Parameter Symbol Test Condition o Tj=25 C Output voltage Vout Line Regulation REGline Load Regulation Quiescent Current Quiescent Current Change REGload Iq ΔIq 27V≤Vin≤38V, 10mA≤Iout≤1.5A, PD ≤15W 27V≤Vin≤38V o Tj=25 C 28V≤Vin≤32V 10mA≤Iout≤1.5A o Tj=25 C 250mA≤Iout≤750mA o Iout=0, Tj=25 C 27V≤Vin≤38V 10mA≤Iout≤1.5A o 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 27V≤Vin≤37V o Iout=1.0A, Tj=25 C f=1KHz o Tj=25 C o Tj=25 C Min Typ Max 23.07 24 24.96 22.85 24 25.20 --------54 ----- 18 6 12 4 4.6 --170 70 2 28 150 2.2 480 240 480 240 8 1 0.5 ------- Unit V mV mA Output Noise Voltage Vn µV Ripple Rejection Ratio RR dB Voltage Drop Vdrop V Output Resistance Rout mΩ Output Short Circuit Current Ios mA Peak Output Current Io peak A Temperature Coefficient of o o o ΔVout/ ΔTj Iout=10mA, 0 C≤Tj≤125 C --1.5 -mV/ C Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 6/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator Electrical Characteristics Curve Figure 1. Peak Output Current as a Function of Input-Output Differential Voltage Figure 2. Ripple Rejection as a Function of Output Voltage Figure 3. Ripple Rejection as a Function of Frequency Figure 4. Output Voltage as a Function of Junction Temperature Figure 5. Output Impedance as a Function of Output Voltage Figure 6. Quiescent Current as a Function of Temperature 7/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator Application Information 2 Figure 7. D PAK Thermal Resistance and Maximum Power Dissipation vs. P.C.B Copper Length 8/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O P TO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 3.740 3.910 0.147 0.154 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270 Marking Diagram XX Y M L CZ = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for TO-220 9/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator ITO-220 Mechanical Drawing DIM A B C D E F G H I J K L M N O ITO-220 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 9.96 10.36 0.392 0.407 6.20 (typ.) 0.244 (typ.) 2.20 (typ.) 0.087 (typ.) ∮1.40 (typ.) ∮0.055 (typ.) 15.07 16.07 0.593 0.632 0.80 (typ.) 0.031 (typ.) 2.44 2.64 0.096 0.104 13.08 13.48 0.514 0.530 1.47 (max.) 0.057 (max.) 3.20 3.40 0.125 0.133 4.60 4.80 0.181 0.188 1.15 (typ.) 0.045 (typ.) 2.44 2.64 0.096 0.104 2.60 2.80 0.102 0.110 6.55 6.65 0.258 0.262 Marking Diagram XX Y M L CI = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code = Package Code for ITO-220 10/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator TO-263 Mechanical Drawing DIM A B C D E F G H I J TO-263 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.000 10.500 0.394 0.413 14.605 15.875 0.575 0.625 0.508 0.991 0.020 0.039 2.420 2.660 0.095 0.105 4.064 4.830 0.160 0.190 1.118 1.400 0.045 0.055 0.450 0.730 0.018 0.029 8.280 8.800 0.325 0.346 1.140 1.400 0.044 0.055 1.480 1.520 0.058 0.060 Marking Diagram XX = Output Voltage (05=5V, 06=6V, 08=8V, 09=9V, 10=10V, 12=12V, 15=15V, 18=18V, 24=24V) Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code CM = Package Code for TO-263 11/12 Version: A07 TS7800B Series 3-Terminal Fixed Positive Voltage Regulator Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 12/12 Version: A07