UTC 6610 CMOS IC FREQUENCY AND CLOCK DISPLAY DRIVER The UTC 6610 is a frequency and clock display driver used for displaying FM/AM radio frequency or a 12 hour alarm clock. By using CMOS technology, it consumes very low power in clock display mode. FEATURES * FM input with pre-scalar for radio frequency up to 150 MHz * AM input for radio frequency up to 30 MHz * 3 common, 13 segment, 1/3 bias LCD display drivers which supports 4 digits LCD display * On chip oscillator for external 32.768kHz crystal * 10.7 MHz / 70 kHz I.F. frequency offset for FM signal and 455kHz I.F. frequency offset for AM signal * Internal real time clock in 12 hour display mode * Selectable clock or frequency display * 1.8V to 3.3V supply voltage QFP-48-12×12-0.8 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG3 SEG4 SEG5 SEG6 COM3 SEG0 SEG1 SEG2 COM1 COM2 VDD AVDD BLOCK DIAGRAM LCD DRIVER FMIN AMP AMIN AM/FM-SEL IF70K AMP PRESCALER DIV.BY 10 VLCD COUNTER CLKFREQ-SEL RST AL-SIG AL-OUT PR SET OSC IN MIN SET AL DISP AL ON/OFF CLOCK M U X OSC OUT TEST VSS AVSS TIMMING CTL TEST CLK RANGE UTC IF FREQ OFFSET UNISONIC TECHNOLOGIES CO. LTD 1 QW-R502-011,A UTC 6610 CMOS IC MIN-SET NC HR-SET NC VSS CLKFREQ-SEL AL-SIG AL-OUT NC IF70K RANGE NC PAD ASSIGNMENT QFP-48- 12×12-0.8 PACKAGE 36 35 34 33 32 31 30 29 28 27 26 25 24 AL DISP AM/FM-SEL 37 AVDD 38 23 AL ON/OFF AMIN 39 22 TEST AVSS 40 21 TEST CLK FMIN 41 20 RST VDD 42 19 VSS 6610 VSS 43 18 VLCD COM1 44 17 OSCOUT COM2 45 16 OSC IN COM3 46 15 SEG12 14 SEG11 SEG0 47 4 5 6 7 8 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 AL-SIG VSS CLKFREQ-SEL NC 9 10 11 12 NC 3 SEG10 2 SEG3 NC 1 SEG2 13 NC SEG1 NC 48 MIN-SET NC AL-OUT 23 IF70K 24 RANGE 33 32 31 30 29 28 27 26 25 NC HR-SET QFP-44- 10×10-.8 PACKAGE 22 AL DISP NC 34 AM/FM-SEL 35 21 AL ON/OFF AVDD 36 20 TEST AMIN 37 19 TEST CLK AVSS 38 18 RST 6610 FMIN 39 17 VLCD VDD 40 16 OSCOUT COM1 41 15 OSC IN COM2 42 14 SEG12 COM3 43 13 SEG11 SEG0 44 UTC 3 4 5 6 7 8 9 10 11 NC SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG10 SEG9 2 SEG1 12 NC 1 UNISONIC TECHNOLOGIES CO. LTD 2 QW-R502-011,A UTC 6610 CMOS IC MIN-SET HR-SET NC VSS CLKFREQ-SEL AL-SIG AL-OUT NC IF70K RANGE COB PACKAGE,QFP TYPE 30 29 28 27 26 25 24 23 22 21 20 AL DISP AM/FM-SEL 31 AVDD 32 19 AL ON/OFF AMIN 33 18 TEST AVSS 34 17 TEST CLK FMIN 35 16 RST 6610 VDD 36 15 VLCD COM1 37 14 OSCOUT COM2 38 13 OSC IN COM3 39 12 SEG12 SEG0 40 5 6 7 SEG1 SEG3 SEG4 SEG5 SEG6 SEG7 8 9 10 SEG10 4 SEG9 3 SEG8 2 SEG2 11 SEG11 1 COB PACKAGE SOP TYPE COM1 1 36 VDD COM2 2 35 FMIN COM3 3 34 VSS SEG0 4 33 AMIN SEG1 5 32 AM/FM-SEL SEG2 6 31 RANGE SEG3 30 NC 7 SEG4 8 29 IF70K SEG5 9 28 AL-OUT SEG6 10 SEG7 11 UTC 6610 27 AL-SIG 26 CLKFREQ-SEL SEG8 12 25 NC SEG9 13 24 HR-SET SEG10 14 23 MIN-SET SEG11 15 22 AL DISP SEG12 16 21 AL ON/OFF OSC IN 17 20 RST OSCOUT 18 19 VLCD UNISONIC TECHNOLOGIES CO. LTD 3 QW-R502-011,A UTC 6610 CMOS IC ABSOLUTE MAXIMUM RATINGS ( Ta=25°C ,unless otherwise specified ) SYMBOL RATING UNIT Supply Voltage Input Voltage Output Voltage PARAMETER VDD VIN VOUT 0.5 ~ 7.0 -0.5 ~ VDD+0.5 -0.5 ~ VDD+0.5 Storage Temperature ESD Protection TSTG -40 ~ +125 -2 ~ + 2 V V V °C kV ELECTRICAL CHARACTERISTICS(Ta=25°C, VDD= 3,Unless otherwise specified) Parameter Symbol Supply Voltage VDD Supply Current Consumption Internal LCD Reference Voltage LCD Drive Current consumption LCD Frame Frequency Oscillator Frequency FM Input Frequency AM Input Frequency FM Input impedance AM Input impedance Open Drain Low Level Voltage Low Level Input Voltage High Level Input Voltage Low Level Output Voltage High Level Output Voltage Schmitt Trigger Positive Threshold Schmitt Trigger Negative Threshold Schmitt Trigger Input Resistance Reset Pin pull-up Resistance VDD IDD1 IDD2 VLCD ILCD FLCD FOSC FFM FAM RIN(FM) RIN(AM) VOLoc VIL VIH VOL VOH Vt+ VtRIN+/RIN-UP Test conditions frequency mode clock mode respect to VDD all segments on MIN TYP MAX UNIT 2 1.8 55 2.25 3.6 110 2.5 5 mA µA V µA Hz kHz MHz MHz Ω kΩ V V V V V V V kΩ kΩ 32 32.768 VIN = 0.3 VPP VIN = 0.3 VPP FFM =120MHz FAM =12MHz VDD=3V, Isink =10mA 11.0 0.5 150 30 150 2.0 0.5 0.3VDD 0.7VDD VDD=3V, Isink=4mA VDD=3V, ISOURCE=-4mA VDD=3V VDD=3V pull-up or pull-down 0.4 VDD-0.5 0.6 2.3 0.9 75 750 2.4 PAD DESCRIPTION PAD NO. SYMBOL 1 VDD 2~4 COM1 ~ COM3 5 ~ 17 SEG0 ~ SEG12 OSCI 18 OSCO 19 VLCD 20 I/O 21 22 23 24 25 26 27 28 29 RST TESTCLK TEST AL-ON/OFF AL-DISP MIN-SET HR-SET NC CLKFREQ-SEL ISU ISD ISD ISU ISU ISU ISU 30 31 32 VSS AL-SIG AL-OUT UTC OL OL I O O ISD OD10 O4 DESCRIPTION Supply voltage LCD common drive signal for driving LCD display LCD segment drive signal for driving LCD display 32.768 kHz crystal oscillator input pin 32.768 kHz crystal oscillator output pin LCD Supply voltage. Connects a 0.1 µF capacitor between this pin and VSS Active low power-on reset with pull-up resistor of approx.750kΩ For testing use only with internal pull-down When high, the chip will enter test mode Alarm function on or off in toggle mode. Internal pull up input When pressed, will display the alarm time. Internal pull up input Minute setting for time and alarm(together with AL-DISP). Internal pull up. Hour setting for time and alarm(together with AL-DISP). Internal pull up. No connection Clock or frequency display mode. Internal pull-down input. When low, clock will be displayed. When high, radio frequency will be displayed. Ground pin Open drain alarm signal output, active low. Alarm output at 1kHz with 0.2 sec on and 0.2 sec off, push-pull output. UNISONIC TECHNOLOGIES CO. LTD 4 QW-R502-011,A UTC 6610 33 CMOS IC IF70k ISD Select IF offset in FM mode. H:70kHz, L:10.7kHz PAD NO. SYMBOL I/O DESCRIPTION 34 NC No connection 35 RANGE ISU For frequency counting mode only, Range = H or L, gate time = 0.1S 36 AM/FM-SEL ISU AM/FM mode selection. High for AM and low for FM, internal pull-up. 37 AVDD Analog Supply voltage 38 AMIN AM signal input, 0.3V peak to peak, 500kHz to 30MHz. 39 AVSS Analog Ground pin. 40 FMIN FM signal input, 0.3V peak to peak, 11-150MHz. Note: I : Oscillator Input Pad O: Oscillator Output Pad ISU: Schmitt trigger input pad with pull-up D10: Open Drain with 10mA output driving ISD: Schmitt trigger input pad with pull-down O4: Push-pull output pad with 4mA driving OL: LCD segment and common output pad FUNCTIONAL DESCRIPTION 1. RADIO FREQUENCY DISPLAY OPERATION (DTS MODE): The FM and AM local oscillator output generated from the external RF receiver enters a high gain input comparator through the FMIN and the AMIN pins respectively. The FM signal then routes through a divide-by10 dynamic pre-scalar. Depending on the state of the AM/FM-SEL pin, the FM and AM signal will be selected and enters the IF frequency offset block. Depending on the FM/AM selection, 10.7MHz/70kHz or 455kHz I.F.frequency will be subtracted or added from the input signal. LCD DISPLAY RANGE: MODE RANGE DISPLAY RANGE (ON LCD) FM H 11.00 MHz to 99.99 MHz L 11.00 MHz to 149.9 kHz AM H 500 kHz to 9999 kHz L 0.5 MHz to 29.99 MHz Note:1 When counter frequency overflow, MSB will not be displayed. STEP RESOULTION 10kHz 100kHz 1kHz 10kHz 1kHz 10kHz 100kHz 1kHz IF OFFSET FOR DIFFERENT APPLICATION: IF70K AM/FM-SEL IF Offset 0 0 +10.7MHz 0 1 +455kHz 1 0 -70 kHz* 1 1 +455kHz * Suitable to use with TDA7088. Operation Display FM input frequency 10.7MHz Display AM input frequency 455kHz Display FM input frequency +70kHz Display AM input frequency 455kHz 2. CLOCK FUNCTION: (1) The clock will be advanced in the following flow: PM 12:00 → PM 11:59 → AM 12:00 → 11:59 (2) The [:] sign is the second indicator and will blink at a rate of 2Hz (3) TIME SETTING: -- Pressing the keys combination of [TIME SET] [HR SET] or [TIME SET] [MIN SET] will enter the time setting mode. -- One digit will be incremented after entering the alarm setting mode. Keep pressing the keys combination for more than 0.5 seconds will make the digit to be advanced at a rate of 2Hz. (4) ALARM TIME SETTING: -- Pressing the keys combination of [AL DISP] [HR SET] or [AL DISP] [MIN SET] will enter the alarm time setting mode. The [AL] indicator will turn on and the [:] sign will stop blinking. -- One digit will be incremented after entering the alarm setting mode. Keep pressing the keys combination UTC UNISONIC TECHNOLOGIES CO. LTD 5 QW-R502-011,A UTC 6610 CMOS IC for more than 0.5 seconds will make the digit to be advanced at a rate of 2Hz. (5) ALARM FUNTION: -- AL OUT output pin will output an alarm frequency of 1024Hz at 0.2 sec on and 0.2 sec off. -- AL OUT pin can be used to direct drive a piezo buzzer. -- When alarm is active, AL OUT output can be disabled by pressing the [AL-ON/OFF] key or it will turn off automatically after 3 minutes lapse. -- AL-SIG pin is an open drain output (active low). Once alarm is activated, AL-SIG can be disabled by pressing [AL-ON/OFF] key or it will turn off automatically after one hour time lapse. -- When [AL DISP] is pressed, alarm setting time will be displayed on the LCD and the [AL] indicator will be on. -- The [AL-ON/OFF] pin will toggle the [ ] indicator to turn on of off the alarm function. When the indicator is on, alarm function is on. (6) 32.768kHz crystal is used for the reference frequency. (7) After Power-on-reset (RST): -- [HR SET] and [MIN SET] keys will be disabled. -- [AL-DISP] KEY,[AL-ON/OFF] KEY AND AL-SIG output will be enabled. 3. After POWER-ON-SET(RST): -- When in clock mode, it will display and start at AM 7:00. -- When in DTS frequency mode, if CLKFREQ-SEL = High, and FMIN & AMIN pins are grounded, all LCD segments will be turned on(LCD test mode). 4. LCD pin configuration and 0 to 9 digits segments display configuration. LCD MAPPING PIN FUNCTION 1 2 3 COM1 COM2 COM3 COM1 4 SEG0 kHz MHz 5 6 7 8 9 10 11 12 13 14 15 16 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 AL DIG1-d DP1 DP2 DIG2-d : AM DIG3-d DIG1-c DIG1-g DIG1-e DIG2-c DIG2-g DIG2-e DIG3-c DIG3-g DIG3-e DIG4-c DIG4-g DIG34-e COM2 COM3 FM DIG4-d PM DIG1-b DIG1-a DIG1-f DIG2-b DIG2-a DIG2-f DIG3-b DIG3-a DIG3-f DIG4-b DIG4-a DIG4-f PIN16 PIN1 COL a AM g b MHz e 1 c KHz AL FM PM 4 3 2 DP2 UTC S1 f DP1 d UNISONIC TECHNOLOGIES CO. LTD 6 QW-R502-011,A UTC 6610 CMOS IC LCD TIMMING WAVEFORMS O n e C y c le VDD V L C D 1 /3 V L C D 2 /3 VLC D VDD V L C D 1 /3 COM2 V L C D 2 /3 VLC D VDD V L C D 1 /3 COM3 V L C D 2 /3 VLC D VDD V L C D 1 /3 SEGX V L C D 2 /3 VLC D O n e C y c le COM1 SEGX SEGX SEGX SEGX SEGX SEGX COM1 COM2 COM3 COM1 COM2 COM3 ON ON ON ON ON ON SUGGESTED APPLICATION AM Local Oscillator 500kHz 30MHz AM Local Oscillator Frequency Clock Buffer 11kHz 150MHz FM Local Oscillator Frequency Clock Buffer 6610 LCD Radio Frequency Receiver AMIN FMIN FM Local Oscillator UTC UNISONIC TECHNOLOGIES CO. LTD 7 QW-R502-011,A UTC 6610 CMOS IC TYPICAL LCD LAYOUT Counter Only Mode PIN COM1 1 COM1 2 3 4 kHz 5 AL 6 1D 7 DP1 8 DP2 9 2D 10 COL 11 AM 12 3D 13 14 FM 15 4D 16 PM COM2 COM3 COM2 MHz 1C 1G 1E 2C 2G 2E 3C 3G 3E 4C 4G 4E COM3 S1 1B 1A 1F 2B 2A 2F 3B 3A 3F 4B 4A 4F PIN16 PIN1 COL S1 AM MHz FM PM DP2 Clock and Counter Mode PIN COM1 COM2 1 COM1 2 COM2 3 4 kHz MHz 5 TS 1C 6 1D 1G 7 1P 1E 8 2P 2C 9 2D 2G 10 COL 2E 11 3C 12 3D 3G 13 S1 3E 14 FM 4C 15 4D 4G 16 PM 4E 17 AM 18 AL 19 MW 20 LW 21 SW UTC DP1 KHz AL COM3 COM3 TK 1B 1A 1F 2B 2A 2F 3B 3A 3F 4B 4A 4F UNISONIC TECHNOLOGIES CO. LTD 8 QW-R502-011,A UTC 6610 CMOS IC s1 AL COL a DZS TK g b AM f MW FM e LM PM SW 4 c 3 d 2P 2 1P 1 MHz KHz TS PIN1 PIN21 AM MW LW stereo SW TYPICAL APPLICATION CIRCUITS 1 UTC UNISONIC TECHNOLOGIES CO. LTD 9 QW-R502-011,A UTC 6610 CMOS IC SEG12 SEG7 SEG8 SEG9 SEG10 SEG11 SEG2 COM1 COM2 COM3 SEG0 SEG1 10nf SEG3 SEG4 SEG5 SEG6 4-DIGITS LCD DISPLAY 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 VDD 10uf AVDD VDD VLCD LCD DRIVER FMIN AMP AMIN IF FREQ OFFSET PRESCALER DIV.BY 10 0.1μF COUNTER CLKFREQ-SEL 4.7kΩ RST 1MΩ AMP VDD 0.1μF AM/FM-SEL IF70k AL-SIG CLOCK M U X 20pF 32.768 kHz AL ON/OFF MINSET AL DISP PRESET OSCIN OSCOUT AL-OUT TESTCLK TEST AVss Vss TIMMING CTL RANGE 20pF TYPICAL APPLICATION CIRCUITS 2 UTC UNISONIC TECHNOLOGIES CO. LTD 10 QW-R502-011,A 0.1μF VP 3v 82pF 68pF 220pF 2pF 470kΩ 100kΩ 9013 220Ω 9012 330kΩ 100kΩ 0.1μH 9018 10μF 0.1μF 2pF AIIpass Filter 6k V2 0.1μF 470pF 10kΩ 5.4k RUM 0.1μF IF Limiter -1 Loop filter AF Demodulator AF MUTE FM VDD FMIN AMIN VLCD NC SEG9 13 CLKFREQ AL-ON -SEL /OFF IF70k VSS AM/FM-SEL RANGE SEG11 15 Alarm On/Off SEG8 12 ALDISP Alarm Set HRSET SEG4 8 HR MINSET SEG3 7 Time Set MHz MIN NC COM1 COM2 COM3 0.1μF RST OSCIN OSCOUT AL-SIG AL-OUT 3 10kΩ 9013 20kΩ 2pF 9018 TDA7088 6k 5k 330pF vp V3 Audio Out 10kΩ 2 4 1 5 SEG0 27 28 30 17 18 SEG6 10 6610 SEG1 20 36 33 35 25 19 29 34 32 31 6 SEG2 23 SEG5 9 24 SEG7 11 22 13 1.8nF 3 SEG10 14 21 3.9nF V2 10 SEG12 16 26 180pF R s 2.2k 2.2k 3.3nF V1 & Search Tuning V2 7 8 0.1μF 10nF 5.6kΩ reset 0.1μF 680pF BB910 10kΩ 0.1μF 6 Buzzer 32768Hz 11 UNISONIC TECHNOLOGIES CO. LTD UTC 15 2 9 1 Mixer VCO 11 5 12 4 14 16 CMOS IC UTC 6610 PAD COORDINATES QW-R502-011,A UTC 6610 CMOS IC (0,0) CHIP SIZE: 2.02 ×2.70mm PAD COORDINATES UTC UNISONIC TECHNOLOGIES CO. LTD 12 QW-R502-011,A UTC 6610 CMOS IC PAD No. X Y PAD No. X Y 1 99 1258 21 1899 1473 2 99 1033 22 1899 1670 3 99 835 23 1899 1868 4 99 637 24 1899 2066 5 99 440 25 1899 2263 6 120 98 26 1899 2570 7 318 98 27 1701 2570 8 516 98 28 1504 2570 9 713 98 29 1306 2570 10 911 98 30 1093 2547 11 1108 98 31 908 2570 12 1306 98 32 732 2558 13 1504 98 33 538 2570 14 1701 98 34 314 2556 15 1899 98 35 120 2570 16 1899 440 36 99 2263 17 1899 682 37 99 2045 18 1899 880 38 99 1823 19 1899 1078 39 95 1648 20 1899 1275 40 99 1428 (Unit :μm) UTC UNISONIC TECHNOLOGIES CO. LTD 13 QW-R502-011,A UTC 6610 CMOS IC COB PACKAGE (QFP TYPE) (UNIT: mm) 23.0±1.0 23.0±1.0 10.0 MAX 2.0 MAX 1.27 1.778 COB PACKAGE (SOP TYPE) (UNIT: mm) 23.0±1.0 7.0 MAX 10.0±0.5 2.0 MAX 1.27 UTC 0.5 UNISONIC TECHNOLOGIES CO. LTD 14 QW-R502-011,A UTC 6610 CMOS IC UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UTC UNISONIC TECHNOLOGIES CO. LTD 15 QW-R502-011,A