COILCRAFT EPL3015

Document 634-1
Shielded Power Inductors – EPL3015
• Low profile shielded power inductors, 3 × 3 × 1.5 mm
• Extremely low DCR and high SRF ratings
• Isat ratings up to 2.4 A
• More values will be available soon
Designer’s Kit C405 contains 5 each of all values
Core material Ferrite
Terminations RoHS compliant tin-silver-copper over tin over nickel
over silver. Other terminations available at additional cost.
Weight 45 – 51 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″reel; 7500/13″ reel Plastic tape: 8 mm wide, 0.2
mm thick, 4 mm pocket spacing, 1.65 mm pocket depth
PCB washing Only pure water or alcohol recommended
Part number1
Inductance2
±20% (µH)
EPL3015-901ML_ 0.90
EPL3015-122ML_ 1.2
EPL3015-152ML_ 1.5
EPL3015-222ML_ 2.2
EPL3015-332ML_ 3.3
EPL3015-472ML_ 4.7
EPL3015-682ML_ 6.8
EPL3015-103ML_10
EPL3015-153ML_15
EPL3015-223ML_22
EPL3015-333ML_33
DCR (Ohms)3
nom max
0.048
0.055
0.054
0.062
0.062
0.072
0.082
0.094
0.108
0.124
0.145
0.167
0.194
0.223
0.301
0.346
0.435
0.500
0.576
0.662
0.860
0.989
Isat (A)5
typ4
(MHz)
10% drop 20% drop 30% drop
SRF
130
105
100
75
55
50
38
32
26
20
15.5
1.201.902.40
1.001.602.05
0.901.401.90
0.751.201.60
0.651.101.40
0.550.901.20
0.450.751.00
0.350.590.81
0.240.430.62
0.210.360.51
0.190.320.45
Irms (A)6
20°C rise 40°C rise
1.85 2.45
1.80 2.40
1.55 2.05
1.50 2.00
1.20 1.70
1.00 1.40
0.90 1.20
0.76 1.00
0.61 0.82
0.56 0.74
0.44 0.59
1. When ordering, please specify packaging code:
EPL3015-333MLC
Packaging:C=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A network analyzer or equivalent.
5. DC current at which the inductance drops the specified amount from its value without current.
6. Current that causes the specified temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 634-1 Revised 09/17/09
Document 634-2
Shielded Power Inductors – EPL3015 Series
Typical L vs Frequency
Typical L vs Current
100
33 µH
10 µH
6.8 µH
4.7 µH
10
2.2 µH
0.9 µH
1
33 µH
Inductance (µH)
Inductance (µH)
100
10
10 µH
6.8 µH
4.7 µH
2.2 µH
1
0.9 µH
0.1
1
0.1
10
100
0.1
0.01
1
0.1
Frequency (MHz)
Current Derating
Part Marking
120
110
2nd
significant
digit
0.118 ±0.008
3,0 ±0,2
100
1st
significant
digit
Multiplier
90
80
0.118 ±0.008
3,0 ±0,2
70
60
0.061
max
1,55
50
Recommended
Land Pattern
40
25°C
Percent of rated Irms
10
Current (A)
30
Start
0.082
2,08
Finish
20
10
0
-40
-20
0
20
40
60
80
100
0.126
3,2
120 140
Ambient temperature (°C)
Part Marking (Parts manufactured prior to Sept. 15, 2009 may not be marked.)
Part number
EPL3015-901
EPL3015-122
EPL3015-152
EPL3015-222
EPL3015-332
EPL3015-472
EPL3015-682
EPL3015-103
EPL3015-153
EPL3015-223
EPL3015-333
Value
0.90 µH
1.2 µH
1.5 µH
2.2 µH
3.3 µH
4.7 µH
6.8 µH
10 µH
15 µH
22 µH
33 µH
1st digit
White
Brown
Brown
Red
Orange
Yellow
Blue
Brown
Brown
Red
Orange
2nd digit
Black Red
Green
Red
Orange
Violet Gray
Black
Green
Red
Orange
Multiplier
Brown
Red
Red
Red
Red
Red
Red
Orange
Orange
Orange
Orange
0.043 min
1,1
Dimensions are in
0.044
1,12
inches
mm
Small surface blemishes are not unusual and do not adversely affect performance.
Wire may be visible inside the voids.
Acceptable void sizes:
Top: 0.01 in / 0,254 mm × 0.01 in / 0,254 mm
Sides: 0.02 in / 0,5 mm × 0.047 in / 1,2 mm
Note: All marked parts have three dots. Black dot, used only on -901 and ‑103 as
second significant digit, may be very difficult to see.
Document 634-2 Revised 09/17/09