1008 CHIP INDUCTORS Chip Inductors for Critical Applications ST413RAD ■ Highest Q factors for this body size, roughly 20% higher than our xx413RAA parts. ■ Exceptional SRFs, tight tolerance and batch consistency Part number1 ST413RAD3N0_LZ2 ST413RAD4N1_LZ ST413RAD7N8_LZ2 ST413RAD10N_LZ ST413RAD12N_LZ ST413RAD18N_LZ ST413RAD22N_LZ ST413RAD33N_LZ ST413RAD36N_LZ ST413RAD39N_LZ ST413RAD47N_LZ ST413RAD56N_LZ ST413RAD68N_LZ ST413RAD82N_LZ ST413RADR10_LZ Inductance3 Percent SRF min5 DCR max6 Imax (nH)tolerance Q min4 (GHz)(OhST) (A) 3.0 @50 MHz 5 57 @ 1000 MHz >5.00 38 1.8 4.1 @50 MHz 5 75 @ 1000 MHz >5.00 50 1.8 7.8 @50 MHz 5 51 @ 500 MHz 3.80 50 1.6 10 @50 MHz 5,2 60 @ 500 MHz 3.20 60 1.5 12 @50 MHz 5,2 57 @ 500 MHz 2.40 60 1.5 18 @50 MHz 5,2 62 @ 350 MHz 2.10 70 1.4 22 @50 MHz 5,2 62 @ 350 MHz 2.05 70 1.4 33 @50 MHz 5,2 49 @ 150 MHz 1.70 90 1.2 36 @50 MHz 5,2 57 @ 150 MHz 1.40 90 1.1 39 @50 MHz 5,2 45 @ 150 MHz 1.30 90 1.1 47 @50 MHz 5,2,1 45 @ 150 MHz 1.45 120 0.95 56 @50 MHz 5,2,1 43 @ 150 MHz 1.08 120 0.95 68 @50 MHz 5,2,1 54 @ 150 MHz 1.15 130 0.85 82 @50 MHz 5,2,1 54 @ 150 MHz 1.06 160 0.80 100 @50 MHz 5,2,1 51 @ 150 MHz 0.82 160 0.80 1. When ordering, specify tolerance, termination and testing codes: ST413RADR10GLZ Tolerance: F1% G = 2% J = 5% Termination:L=RoHS compliant silver-palladium-platinum glass frit. Special order: S=Tin-lead (63/37) over silver-platinum-glass frit. T=Tin-silver-copper (95.5/4/0.5) over silver-platinumglass frit. Testing:Z =COTS H=Screening per Coilcraft CP-SA-10001 2. Part is wound on low profile coilform. 3. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/ HP 4286A impedance analyzer or equivalent with Coilcraft-provided correlation pieces. 4. Q measured using an Agilent/HP 4291A with an AgilentHP 16197A test fixture or equivalents. 5. SRF measured using an Aglilent/HP 8753ES network analyzeror equivalent and a Coilcraft SMD-D test fixture. 6. DCR measured on a Keithley 580 micro-ohmmeter or equivalent and a Coilcraft CCF858 test fixture. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Core material Ceramic Terminations Silver-palladium-platinum-glass frit. Ambient temperature –40°C to +125°C with Imax current, +125°C to +140°C with derated current Storage temperature Component: –55°C to +140°C. Tape and reel packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +155 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Packaging 2000/7″reel Standard height parts: Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.8 mm pocket depth Low profile parts: Plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth Document ST190-1 Revised 11/06/12 ® © Coilcraft, Inc. 2012 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information. 1008 CHIP INDUCTORS ST413RAD Series (1008) Typical Q vs Frequency 120 Typical L vs Frequency 120 22 nH 110 10 nH 68 nH 100 100 47 nH 3.0 nH 90 90 70 Inductance (nH) Q Factor 80 100 nH 60 50 40 30 70 50 40 10 0 0 10000 22 nH 30 10 1000 47 nH 60 20 100 68 nH 80 20 10 100 nH 110 10 nH 3.0 nH 1 10 100 Frequency (MHz) 10000 Frequency (MHz) Current Derating B overall 120 H C Pick and place material F 110 100 I G A 90 J F 80 E terminal 70 60 I D Recommended Suggested LandPattern Pattern Land Terminal wraparound: approx 0.015/0,38 both ends 50 40 ABCD max max max* ref 25°C Percent of rated Irms 1000 30 20 F G H IJ 2,922,792,030,512,030,511,522,541,021,27 mm 10 0 -55 -40 E 0.1150.1100.0800.0200.0800.0200.0600.1000.0400.050inches *Low profile parts: 0.050/1,27 -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) Note: Dimensions are before optional solder application. For maximum overall dimensions including solder, add 0.0025 in / 0,064 mm to B and 0.006 in / 0,15 mm to A and C. Document ST190-2 Revised 11/06/12 ® © Coilcraft, Inc. 2012 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information.