H_RN-2W & H_LT-2W Series 2W, FIXED INPUT,6000V ISOLATED & UNREGULATED SINGLE OUTPUT DC-DC CONVERTER Patent Protection RoHS PRODUCT PROGRAM FEATURES ● High Efficiency up to 80% ● DIP/SMD Package ● 6kVDC Isolation ● Temperature Range: -40°C ~ +85°C ● Internal SMD Construction ● No Heatsink Required ● No External Component Required ● Continuous Short Circuit Protection ● Industry Standard Pinout ● RoHS Compliance Input Part Number Voltage (VDC) Output Current (mA) Efficiency (%, Typ.) Certificate* Voltage (VDC) Max. Min. H0503RN-2W 3.3 606 60 71 H0505RN-2W 5 400 40 76 CE H0509RN-2W 9 223 22 78 CE H0512RN-2W 12 167 17 79 CE 15 133 13 78 CE H0505LT-2W 5 400 40 76 CE H0509LT-2W 9 223 22 78 CE H0512LT-2W 12 167 17 79 CE H0515LT-2W 15 133 13 78 CE H1205RN-2W 5 400 40 76 CE H1209RN-2W 9 223 22 79 CE H1212RN-2W 12 167 17 80 CE H1215RN-2W 15 133 13 79 CE 5 400 40 76 CE H1209LT-2W 9 223 22 79 CE H1212LT-2W 12 167 17 80 CE H1215LT-2W 15 133 13 79 CE 2) Where isolation is necessary between input H2405RN-2W 5 400 40 77 CE and output (isolation voltage ≤ 6000VDC); H2409RN-2W 9 223 22 77 CE 3) Where the regulation of the output voltage H2412RN-2W 12 167 17 80 CE H2415RN-2W 15 133 13 78 CE 3.3 400 40 71 Nominal APPLICATIONS The H_RN-2W&H_LT-2W series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤ ±10%); and the output ripple noise are 5 H0515RN-2W not demanding. H1205LT-2W H2403LT-2W 12 24 Range 4.5-5.5 10.8-13.2 21.6-26.4 Such as: purely digital circuits, ordinary low H2405LT-2W 5 400 40 77 CE frequency analog circuits, and IGBT power H2409LT-2W 9 223 22 77 CE device driving circuits. H2412LT-2W 12 167 17 80 CE H2415LT-2W 15 133 13 78 CE Note: 1.Models listed with strike-through text have been officially discontinued. 2.*CE Certificate:EN60601 MODEL SELECTION COMMON SPECIFICATIONS H0505RN-2W Rated Power Package Style Output Voltage Input Voltage Product Series Item Test Conditions Min. Operating temperature -40 Storage temperature -55 1.5mm from case for 10 seconds % °C 25 300 Free air convection Package material Http://www.mornsun-power.com Unit 95 125 15 Cooling Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China. Tel: 86-20-28203030 Fax:86-20-38601272 Max. 85 Temp. rise at full load Lead temperature MORNSUN Science & Technology Co.,Ltd. Typ. Storage humidity Epoxy Resin (UL94-V0) Short circuit protection Continuous, automatic recovery MTBF 3500 Weight K hours 3.8 g ISOLATION SPECIFICATIONS Item Test Conditions Isolation voltage Tested for 1 minute and 1mA max 6000 Isolation resistance Test at 500VDC 1000 Isolation capacitance The copyright and authority for the interpretation of the products are reserved by MORNSUN Min. Typ. Max. Unit VDC MΩ 10 pF Specifications subject to change without notice. H_RN-2W & H_LT-2W C/0-2012 Page 1 of 3 OUTPUT SPECIFICATIONS Item TYPICAL CHARACTERISTICS Test Conditions Min. Output power Typ. 0.2 For Vin change of ±1% Line regulation Load regulation Max. Units 2 W ±1.2 10% to 100% load (5V output) 12.8 15 10% to 100% load (9V output) 8.3 15 10% to 100% load (12V output) 6.8 15 10% to 100% load (15V output) 6.3 15 Output voltage accuracy % See tolerance envelope graph Temperature drift 100% full load Ripple & Noise* 20MHz Bandwidth 150 Switching frequency Full load, nominal input 50 ±0.03 %/°C 200 mVp-p KHz *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter. Section, application notes. RECOMMENDED REFLOW SOLDERING PROFILE P ea k. Temp 26 0 C 10 Sec Ma x 2 20 C Te mperature ( C ) 2 50 2 00 1 50 1 00 90 S ec M ax (>220 C ) 50 Operating Temp.(oC) 0 Tim e (s ec .) Remark: The curve applies only to the hot air reflow soldering APPLICATION NOTE RECOMMENDED CIRCUIT 1) Requirement On Output Load To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, L L +Vo Vin DC DC Cin Cout GND 0V the minimum output load could not be less than 10% of the full load. If the actual output power is very small, please connect a resistor with proper resistance at the (Figure 1) output end in parallel to increase the load, or use our company’s products with a lower rated output power. 2) Recommended testing and application circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be Vin +Vo REG DC DC GND 0V connected to the input and output ends of the DC/DC converter, see (Figure 1). It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance REG Vin +Vo DC DC GND 0V is too big, a startup problem might arise. For every channel of output, provided the safe (Figure 2) and reliable operation is ensured, the recommended capacitance of its filter capacitor sees (Table 1). EXTERNAL CAPACITOR TABLE (TABLE 1) 3) Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current Vin (VDC) Cin (µF) Single Vout (VDC) Cout (µF) protection is a linear voltage regulator with overheat protection that is connected to the 5 4.7 5 10 input or output end in series (Figure 2). 12 2.2 9 4.7 24 1 12 2.2 -- -- 15 1 4) Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self-recovery fuse in It’s not recommended to connect any external series at the input end or add a circuit breaker to the circuit. capacitor in the application field with less than 0.5 watt output. 5) No parallel connection or plug and play The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice. H_RN-2W & H_LT-2W C/0-2012 Page 2 of 3 OUTLINE DIMENSIONS & PIN CONNECTIONS M ECH ANIC AL D IM ENSIO NS RECOMMENDED FOOTPRINT H_RN- 2 W Series H_LT - 2 W Series 23.86±0.20 [0.939±0.008] 23.86 [0.939] 7 1 16 8 10 9 7 8 13.70 ±0.20 [0.539 ±0.008] 9 13.70±0.20 [0.539±0.008] 10 ( Top View ) ( Top View ) 1 9 16 10 1 7 8 2.54[0.100] 0.50±0.10 [0.020±0.004] 2.54 [0.100] 15.28 [0.602] 17.78 [0.700] 17.78[0.700] 16 ∅1.00±0.20 [0.039±0.008] H_RN- 2 W Series 2.54[0.100] 17.78[0.700] H_LT - 2 W Series 17.78±0.35 [0.700±0.700] 1.34 [0.053] MAX18.00[0.709] 2 2.60[0.890] FOOTPRINT DETAILS FOO TPR IN T D ETAILS Pin Function Pin Function 1 7 8 9 10 16 GND NC NC +Vo 0V Vin 1 7 8 9 10 16 GND NC NC +Vo 0V Vin 1.20±0.20 [0.047±0.008] TUBE OUTLINE DIMENSIONS 0.25±0.10 [0.010±0.004 ] 18.10±0.40 [0.713±0.016] 7 8 2.50±0.20 [0.098±0.008] 16.92[0.666] 7.50[0.295] 0~5 2.20±0.20 [0.087±0.008 ] 1 Note: grid 2.54*2.54mm. A ( Side View ) 9 17.78 [0.700] A ( Side View ) 10 10.10 [0.398 ] 15.53[0.611] 0.91±0.20 [0.045±0.008] 0.10 [0.004] MAX3.34 [0.135] 16 15.10 [0.594] 11.00±0.50 [0.433±0.020] MAX3.34 [0.131] 0.50±0.20 [0.020±0.008 ] 17.78 ±0.35 [0.700±0.014 ] ( Front View ) 8.00[0.315] 3.00[0.118] 0.50[0.020] 1.02[0.040] 7.50[0.295] 7.80 [0.307] ( Front View ) 8.40[0.331] Note: Unit: mm[inch] General tolerances:±0.50mm[± 0.020inch] L=530mm[20.866inch] Tube Q uantity:21pcs L=220mm[8.661inch] Tube Q uantity: 8pcs Short tube inner packaging dimensions: L*W*H=255*170*80mm; Short tube outer packaging dimensions(with six inner packaging boxes): L*W*H=375*280*270mm; Long tube inner packaging dimensions: L*W*H=580*200*100mm; Long tube outer packaging dimensions(with two inner packaging boxes)： L*W*H=600*215*220mm; Long tube outer packaging dimensions(with three inner packaging boxes)： L*W*H=600*215*325mm. N C :No connection Note: Unit: mm[inch] Pin section tolerances:±0.10mm[±0.004inch ] General tolerances:±0.25mm[±0.010inch] TAPING RE EL DIMENSIONS 1 8. 42 [0 .7 25 ] 1 .5 0 [ 0. 05 9] 2 .0 0 [ 0. 07 9] 4. 00 [0 .1 57 ] 14 .0 0 [ 0. 55 1] 5.00 [0.197] 4 4. 80 [1 .7 64 ] 10 0. 00 [3 .9 37 ] 330.00[12.992] 23.62[0.930] 20.30[0.799] 44.00[1.732] 1 .7 0 [ 0. 06 7] 13.81[0.544] 0. 50 [ 0. 02 0] 13 .0 0 [ 0. 51 2] 21 .5 0 [ 0. 84 6] 9 .7 0 [ 0. 38 2] 1.5 0 [ 0. 05 9] 2 8. 00 [1 .1 02 ] 2.0 0 [ 0. 07 9] Note: Unit:mm [inch] General Tolerances:±0.50mm [±0.020inch] Per reel of packing quantity:200PCS Innerpackage cartondimensions:L*W*H=365*350*105mm Tube Quantity:400pcs Outerpackagecartondimensions:L*W*H=390*360*245mm Tube Quantity:800pcs Note: 1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life of product. 2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 3. Only typical models listed, other models may be different, please contact our technical person for more details. 4. In this datasheet, all the test methods of indications are based on corporate standards. The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice. H_RN-2W & H_LT-2W C/0-2012 Page 3 of 3