CRYSTEKCRYSTAL E2412T-1W

E_T-1W & F_T-1W Series
1W, FIXED INPUT, ISOLATED & UNREGULATED
DUAL/SINGLE OUTPUT DC-DC CONVERTER
RoHS
FEATURES
● Small Footprint
● SMD Package Style
● 3kVDC Isolation
● Temperature Range: -40°C ~ +85°C
● No Heatsink Required
● Industry Standard Pinout
● Internal SMD construction
● No External Component Required
● RoHS Compliance
APPLICATIONS
PRODUCT PROGRAM
Input
Part
Number
Voltage (VDC)
Output
Current (mA)
Efficiency
Certificate
(%, Typ.)
Voltage
(VDC)
Max.
Min.
F0303T-1W
3.3
304
30
F0305T-1W
5
200
20
75
±5
±100
±10
68
E0312T-1W
±12
±42
±5
77
F0505T-1W
5
200
20
70
UL
F0509T-1W
9
110
11
76
UL
F0512T-1W
12
84
9
78
UL
F0515T-1W
15
66
7
79
UL
±5
±100
±10
71
UL
Nominal
E0305T-1W
3.3
5
E0505T-1W
Range
3.0-3.6
4.5-5.5
73
The E_T-1W & F_T-1W series are specially
E0509T-1W
±9
±55
±6
77
UL
designed for applications where a group of polar
E0512T-1W
±12
±42
±5
78
UL
power supplies are isolated from the input power
E0515T-1W
±15
±33
±4
79
UL
F1203T-1W
3.3
303
30
70
F1205T-1W
5
200
20
69
UL
F1209T-1W
9
110
11
73
UL
F1212T-1W
12
84
9
73
UL
15
66
7
74
UL
±5
±100
±10
71
UL
supply in a distributed power supply system on a
circuit board. These products apply to:
1) Where the voltage of the input power supply is
fixed (voltage variation ≤ ±10%);
2) Where isolation is necessary between input
and output (isolation voltage ≤3000VDC);
3) Where the regulation of the output voltage and
F1215T-1W
12
10.8-13.2
E1205T-1W
the output ripple noise are not demanding.
E1209T-1W
±9
±55
±6
73
UL
Such as: purely digital circuits, ordinary low
E1212T-1W
±12
±42
±5
74
UL
frequency analog circuits, and IGBT power device
E1215T-1W
±15
±33
±4
75
UL
driving circuits.
F2405T-1W
5
200
20
69
F2412T-1W
12
84
9
77
F2415T-1W
15
66
7
74
24
42
5
76
F2424T-1W
24
21.6-26.4
MODEL SELECTION
E2405T-1W
±5
±100
±10
70
F0505T-1W
E2412T-1W
±12
±42
±5
77
E2424T-1W
±24
±21
±3
79
Rated Power
Package Style
Output Voltage
Input Voltage
Product Series
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
Fax:86-20-38601272
Http://www.mornsun-power.com
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Storage humidity
Max.
Units
95
%
Operating temperature
-40
85
Storage temperature
-55
125
Temp. rise at full load
Lead temperature
15
1.5mm from case for 10 seconds
260
Cooling
Package material
Free air convection
Epoxy Resin(UL94-V0)
Short circuit protection*
MTBF
°C
25
1
3500
Weight
s
k hours
1.71
g
*Supply voltage must be discontinued at the end of short circuit duration.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
E_T-1W&F_T-1W
B/0-2010
Page 1 of 3
ISOLATION SPECIFICATIONS
TYPICAL CHARACTERISTICS
Item
Test Conditions
Min.
Typ.
Max.
Units
Isolation voltage
Tested for 1 minute and 1mA max
3000
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
OUTPUT SPECIFICATIONS
Item
Test Conditions
Min.
Output power
Typ.
0.1
For Vin change of ±1%(3.3V output)
Line regulation
Units
1
W
±1.5
±1.2
For Vin change of ±1%(Others output)
10% to 100% load (3.3V output)
Load regulation
Max.
15
20
10% to 100% load (5V output)
12.8
15
10% to 100% load (9V output)
8.3
10
10% to 100% load (12V output)
6.8
10
10% to 100% load (15V output)
6.3
10
10% to 100% load (24V output)
6.0
10
See tolerance envelope
graph
±0.03 %/°C
Output voltage accuracy
Temperature drift
100% full load
Output ripple &Noise*
20MHz
Bandwidth
Switching frequency
Full load, nominal input
%
E_T-1W series
50
75
F_T-1W series
75
100
24V input
500
Others
100
mVp-p
kHz
Operating Temp.(oC)
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
RECOMMENDED REFLOW SOLDERING PROFILE
2 50
1 0 S ec M ax
Te m p eratu r e ( o C)
o
2 00
220 C
Dual Output
L
L
+Vo
Vin
Cout
DC DC
Cin
1 50
1 00
RECOMMENDED CIRCUIT
26 0 o C
90 Se c Ma x
( >2 2 0 oC )
50
0
Ti me ( s ec .)
Remark: The curve applies only to the hot air reflow soldering
GND
-Vo
Si ngl e Output
L
Vin
increase the load, or use our company’s products with a lower rated output power
(E _T-W2/F_T-W2 Series).
2) Recommended testing circuit
If you want to further decrease the input/output ripple, an “LC” filtering network may be
connected to the input and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the frequency of the “LC” filtering network
+Vo
DC DC
Cin
Cout
0V
(Figure 1)
Dual O u tput
Vi n
output load could not be less than 10% of the full load. If the actual output power is very
small, please connect a resistor with proper resistance at the output end in parallel to
L
GND
APPLICATION NOTE
1) Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum
0V
L Cout
R EG
REG
+Vout
REG
-Vout
REG
+Vout
0V
DC DC
GND
S ingle O utput
Vi n
R EG
DC DC
GND
0V
(Figure2)
should be staggered with the DC/DC frequency to avoid mutual interference. However, the
capacitance of the output filter capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output, provided the safe and reliable
operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1).
3) Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current
protection is a linear voltage regulator with overheat protection that is connected to the input
or output end in series (Figure2).
4) Overload Protection
Under normal operating conditions, the output circuit of these products has no protection
against overload. The simplest method is to connect a self-recovery fuse in series at the
EXTERNAL CAPACITOR TABLE (Table 1)
Vin
Cin Single Cout
Dual Cout
(VDC) (µF)
Vout
(µF)
Vout
(µF)
(VDC)
(VDC)
3.3/5
4.7
5
10
±3.3/5 4.7
12
2.2
9
4.7
±9
2.2
24
1
12
2.2
±12
1
-
-
15
1
±15
1
24
0.47
±24
0.47
It’s not recommended to connect any external
capacitor in the application field with less than 0.5 watt
output.
input end or add a circuit breaker to the circuit.
5) No parallel connection or plug and play
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
E_T-1W&F_T-1W
B/0-2010
Page 2 of 3
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
(Side View)
6.25 [0.246]
6.50 [0.256]
1.00 [0.039]
0.60 [0.024]
0.25 [0.010]
15.24 [0.600]
12.70 [0.500]
2.54 [0.100]
12 11 10
1 2
8
3
7
2.54 [0.100]
3
5
6
2.10 [0.083]
2
2.54 [0.100]
7
11.20 [0.441]
5
6
FOOTPRINT DETAILS
Single
Pin
Dual
1
GND
GND
2
Vin
Vin
5
0V
0V
6
NC
-Vo
+Vo
+Vo
8
Others
NC
NC
A
0.25 [0.010]
A
8.50 [0.335]
8
1
(Top View)
7.50 [0.295]
12 11 10
10.10 [0.398]
5°max
1.35 [0.053]
NC:No Connection
Note:
Unit: mm[inch]
Pin section tolerances: 0.10mm[ 0.004inch]
General tolerances: 0.25mm[ 0.010inch]
REEL PACKING OUTLINE DIMENSIONS
TUBE OUTLINE DIMENSIONS
Taping dimension:
∅1.50 [0.059]
1.75 [0.069]
11.50 [0.453]
2.00 [0.079]
0.50 [0.020]
7.40 [0.291]
15.65[0.616]
8.90 [0.350]
24.00 [0.945]
14.10 [0.555]
6.50 [0.256]
4.30 [0.169]
0.60 [0.024]
16.00[0.630]
Taping reel dimension:
∅1.50 [0.059]
29.40 [1.157]
14.10 [0.555]
∅100.00 [3.937]
Note:
Unit: mm[inch]
General tolerances:
0.5mm[
0.020inch]
L=540mm[21.260inch] Devices per tube quantity : 33pcs
L=220mm[8.661inch] Devices per tube quantity : 12pcs
7.35 [0.289]
330.00 [12.992]
11.60 [0.457]
∅13.00 [0.512]
∅21.50 [0.846]
Note:
Unit: mm[inch]
General tolerances: 0.5mm[ 0.020inch]
Devices per reel quantity: 500pcs
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the
life of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
1. Only typical models listed, other models may be different, please contact our technical person for more details.
2. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
E_T-1W&F_T-1W
B/0-2010
Page 3 of 3