Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal Modular Crimp Head Order No. 63811-9570 Application Tooling Specification Sheet TYPE 4A Hand Crimp Tool Order No. 63811-9500 FEATURES % % % % % % A full cycle ratcheting hand tool ensures complete crimps Ergonomically designed soft handles Precisely designed crimping profiles with simple contact positioning Easy handling due to outstanding force ratio Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100, accompanied by Air Powered Crimp Adapter (Order No. 63816-0700). Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V), accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600). SCOPE Products: OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal, 0.30-0.85mm² and 18-22 AWG. Terminal Terminal Order No. Series No. 50420 50420-8100 (loose) 50420-8000 (reel) * Wire Size AVS-0.3, AVS-0.3f 22AWG AVS-0.5, AVS-0.5f AVSS-0.5, AVSS-0.5f CAVS-0.5 20AWG AVS-0.75f, AVSS-0.75f AVS-0.85, AVSS-0.85 CAVS-0.85 18AWG 0.37 0.35 JASO TXL Insulation Diameter Strip Length mm In. mm In. 1.60-1.90 .063-.075 3.00-3.70 .118-.146 1.60-1.90 .063-.075 3.00-3.70 .118-.146 0.56 JASO 1.60-2.10 .063-.083 3.00-3.70 .118-.146 0.50 0.79 TXL JASO 1.60-2.10 .063-.083 3.00-3.70 .118-.146 1.80-2.30 .071-.090 3.00-3.70 .118-.146 0.88 JASO 1.80-2.30 .071-.090 3.00-3.70 .118-.146 0.80 TXL 1.80-2.30 .071-.090 3.00-3.70 .118-.146 Actual mm² Wire Type * Note: When using reeled parts, the cut-off tab must be maintained below 0.20mm (.008”) Doc No: ATS-6381195HM Revision: B Release Date: 08-03-07 Revision Date: 08-10-10 UNCONTROLLED COPY Page 1 of 6 Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal DEFINITION OF TERMS BRUSH BEND UP BELL MOUTH CONDUCTOR CRIMP INSULATION CRIMP ▲SEE NOTE ROLLING TWISTING STRIP LENGTH BEND DOWN CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. OVERLAP FORM GEOMETRY ▲Insulation Crimp Note: Due to the terminal’s insulation grip design and/or insulation diameter range, this tool uses “overlap” form geometry in the insulation punch. This produces an overlap insulation crimp (A620 – compliant). While the insulation punch profile may appear “lopsided”, this is a normal condition for this tool. See figure to the right. (Some tools with multiple crimp pockets may not have the “overlap” profile on all pockets). PUNCH OVERLAP INSULATION CRIMP WIRE ANVIL CRIMP SPECIFICATIONS: After crimping, the conductor profile should measure the following. Conductor Profile AWG Terminal Actual Wire Wire Size Crimp Height (Ref.) Crimp Width (Ref.) 0.3mm2 0.75+0.85mm2 0.5mm2 Series No. mm² Type 22 AWG 18 AWG 20 AWG mm In. mm In. 0.3, 0.3f 0.37 JASO 0.86-0.95 .034-.037 1.60 .063 X 22AWG 0.35 TXL 0.86-0.95 .034-.037 1.60 .063 X 0.5, 0.5f 0.56 JASO 0.96-1.06 .038-.042 1.60 .063 X 50420 20AWG 0.50 TXL 0.96-1.06 .038-.042 1.60 .063 X 0.75f 0.79 JASO 1.10-1.17 .043-.046 1.60 .063 X 0.85 0.88 JASO 1.10-1.17 .043-.046 1.60 .063 X 18AWG 0.80 TXL 1.10-1.17 .043-.046 1.60 .063 X Doc No: ATS-6381195HM Revision: B Release Date: 08-03-07 Revision Date: 08-10-10 UNCONTROLLED COPY Page 2 of 6 Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal Insulation Pull Force Terminal Wire Size Actual mm² Wire Type Crimp Height (Ref.) Crimp Width (Ref.) Minimum Series No. mm In. mm In. N Lb. 0.3, 0.3f 0.37 JASO 2.20 .087 2.30 .091 58.8 13.2 22AWG 0.35 TXL 2.20 .087 2.30 .091 58.8 13.2 0.5, 0.5f 0.56 JASO 2.35 .093 2.40 .094 88.2 19.8 50420 20AWG 0.50 TXL 2.35 .093 2.40 .094 88.2 19.8 0.75f 0.79 JASO 2.50 .098 2.60 .102 107.8 24.2 0.85 0.88 JASO 2.50 .098 2.60 .102 117.6 26.5 18AWG 0.80 TXL 2.50 .098 2.60 .102 117.6 26.5 Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an optimum crimp. Τ OPERATION Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will release the handles, and the hand tool will spring open. Crimping Terminals 1. Lift the wire stop blade up. 2. Insert the terminal fully into the correct profile until the terminal is fully seated and stops. 3. Bring down the wire stop blade. 4. Slide the pre-stripped wire into the wire stop blade. See Figure 1. Be sure to hold the wire in place until the terminal is fully crimped. See Figure 2. 5. Close the tool until the ratchet releases, the tool handles will then spring open. 6. Lift the wire stop blade up if it is still in down position. 7. Carefully remove the crimped terminal. SPACER WIRE STOP CONDUCTOR PUNCH BLADE RETAINER WIRE STOP BLADE INSULATION PUNCH LOCATOR WIRE TERMINAL LOCATOR TERMINAL PRE-STRIPPED WIRE Figure 1 CONDUCTOR ANVIL Figure 2 INSULATION ANVIL Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed. Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No: ATS-6381195HM Revision: B Release Date: 08-03-07 Revision Date: 08-10-10 UNCONTROLLED COPY Page 3 of 6 Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by lifting the ratchet release lever. See Figure 6. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Repetitive use of this tool should be avoided. CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Notes: 1. This tool should only be used for the terminals and wire gauges specified on this sheet. 2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above). Variations in tools, terminals, wire stranding, and insulation types may affect crimp height. 3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes. 4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased. 5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing. Doc No: ATS-6381195HM Revision: B Release Date: 08-03-07 Revision Date: 08-10-10 UNCONTROLLED COPY Page 4 of 6 Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal 6. Molex does not certify crimp hand tools. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. Applications for the Modular Crimp Head WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction and without first reading and understanding the instructions in the proper Manual or Specification Sheet. See Chart below for the correct Manual or Specification Sheet. WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the power by unplugging or turn off the Actuator from its power source. CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury. CAUTION: Wear safety glasses when operating or serving this tool. The chart below shows all applications for this Modular Crimp Head. Modular Crimp Head Order No. 63811-9570 Tool Tool Adapter Adapter Figure Order no. Description Order No. Description No. 63816-0000 Hand Crimp Frame (Short) N/A N/A 3 63816-0050 Hand Crimp Frame (Long) N/A N/A 3 63816-0200 Battery Power Tool (110 V) 63816-0600 Battery Power Crimp Adapter 4 63816-0250 Battery Power Tool (220 V) 63816-0600 Battery Power Crimp Adapter 4 63816-0100 Air Power Tool 63816-0700 Air Power Crimp Adapter 5 Applications for the Modular Crimp Head Hand Crimp Tool Battery Powered Tool MODULAR CRIMP HEAD LOCKING PINS MODULAR CRIMP HEAD LOCKING PINS HAND CRIMP FRAME LONG OR SHORT Doc No: ATS-6381195HM Revision: B LOCKING PINS AIR POWER CRIMP ADAPTER BATTERY POWERED TOOL LOCKING PINS AIR POWER TOOL Figure 4 Release Date: 08-03-07 Revision Date: 08-10-10 MODULAR CRIMP HEAD BATTERY POWER CRIMP ADAPTER LOCKING PINS Figure 3 Air Powered Tool UNCONTROLLED COPY Figure 5 Page 5 of 6 Hand Crimp Tool for OBD II 4.00mm (.157") Wire-to -Wire Crimp Terminal PARTS LIST Hand Crimp Tool 63811-9500 Item Order Number Description Quantity 1 63811-9570 Modular Crimp Head 1 (Ref) 2 63816-0050 Hand Crimp Frame (Long) 1 (Ref) 3 63811-9575 Locator 1 4 63816-0001 Locking Pin 2 5 63600-0525 Handle Spring 1 6 63600-0520 Crimping Spring 2 5 HANDLE SPRING 2 M4 X FLAT WASHER M4 X 14mm LONG BHCS RATCHET RELEASE LEVER 3 4 1 6 CRIMPING SPRING (2) Figure 6 http://www.molex.com Doc No: ATS-6381195HM Revision: B Release Date: 08-03-07 Revision Date: 08-10-10 UNCONTROLLED COPY Page 6 of 6