Low Signal Relay
G6A
Fullly Sealed Relay with High Impulse Withstand
• High sensitivity — can be driven by digital circuits.
• Low-profile design allows use in 12.70 mm PC board rack.
• Surge withstand voltage meets FCC Part 68 regulation.
• Units can be mounted side by side due to low magnetic
leakage.
• Special models available for low thermoelectromotive force.
• Unique moving loop (permanent magnet) armature reduces
relay size, magnetic interference, and contact bounce time.
• Single or dual coil winding types available.
• RoHS Compliant
RC FCC
Ordering Information
To Order: Select the part number and add the desired coil voltage rating, (e.g., G6A-274P-ST-US-DC12).
■ Non-latching
Type
Contact form
Model
Ag (Au clad)
Standard
Low-sensitivity
DPDT
G6A-274P-ST-US
4PDT - DISCONTINUED
G6A-474P-ST-US
DPDT
G6A-274P-ST40-US
4PDT - DISCONTINUED
G6A-474P-ST40-US
■ Latching
Single Coil
Type
Contact form
Model
Ag (Au clad)
Standard
DPDT
G6AU-274P-ST-US
4PDT - DISCONTINUED
G6AU-474P-ST-US
Dual Coil
Type
Contact form
Model
Ag (Au clad)
Standard
Low-sensitivity
DPDT
G6AK-274P-ST-US
4PDT - DISCONTINUED
G6AK-474P-ST-US
DPDT
G6AK-274P-ST40-US
4PDT - DISCONTINUED
G6AK-474P-ST40-US
Low Signal Relay
G6A
81
Specifications
■ Contact Data
Type
G6A-274P-ST(40)-US, G6A-474P-ST(40)-US
G6AK-274P-ST(40)-US, G6AK-474P-ST(40)-US
G6AU-274P-ST-US, G6AU-474P-ST-US
Load
Resistive load (p.f. = 1)
Inductive load (p.f. = 0.4)
(L/R = 7 ms)
Rated load
0.50 A at 125 VAC,
2 A at 30 VDC
0.3 A* at 125 VAC,
1 A at 30 VDC
Contact material
Ag (Au clad)
Carry current
3A
Max. operating voltage
250 VAC, 220 VDC
Max. operating current
2A
1A
Max. switching capacity
125 VA, 60 W
62.50 VA, 30 W
Min. permissible load (See note)
10 μA, 10 mVDC
* 0.25A at 125VAC for latching models
Note: 1. P level: λ60 = 0.1 x 10–6/operation
This value was measured at a switching frequency of 60 operations/min and the criterion of contact resistance is 50 Ω. This value may
vary depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.
2. G6A-4 pole versions are discontinued.
■ Coil Data
Standard Non-latching DPDT (G6A-274P-ST-US)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance
(ref. value) (H)
Armature
OFF
Pick-up
voltage
Armature
ON
3
66.70
45
0.07
0.065
4.5
44.6
101
0.16
0.14
5
40
125
0.20
0.18
6
33.30
180
0.29
0.26
9
22.20
405
0.63
0.57
12
16.70
720
1.10
1.06
24
8.30
2,880
4.50
4.10
48
4.90
9,750
13.70
12.50
Dropout
voltage
Maximum
voltage
% of rated voltage
70% max.
10% min.
200%
at 23°C
Power
consumption
(mW)
Approx. 200
Approx. 235
Low-sensitivity Non-latching DPDT (G6A-274P-ST40-US)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance
(ref. value) (H)
Armature
OFF
Pick-up
voltage
Armature
ON
3
133.30
22.50
0.03
0.02
4.5
88.9
50.6
0.065
0.06
5
80
62.50
0.08
0.07
6
66.70
90
0.11
0.10
9
44.30
203
0.27
0.23
12
33.30
360
0.52
0.43
24
16.70
1,440
2.10
1.80
48
8.30
5,760
7.50
6.40
Dropout
voltage
Maximum
voltage
% of rated voltage
70% max.
10% min.
150%
at 23°C
Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.
2. Operating characteristics are measured at a coil temperature of 23°C.
3. The maximum voltage is the highest voltage that can be imposed on the relay coil.
82
Low Signal Relay
G6A
Power
consumption
(mW)
Approx. 400
Standard Non-latching 4PDT (G6A-474P-ST-US - DISCONTINUED)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance
(ref. value) (H)
Armature
OFF
Pick-up
voltage
Armature
ON
3
120
25
0.05
0.045
4.5
79.9
56.3
0.11
0.095
5
72.50
69
0.14
0.12
6
60
100
0.20
0.17
9
40
225
0.45
0.38
12
30
400
0.80
0.68
24
15
1,600
3.20
2.70
48
7.50
6,400
12.80
10.90
Dropout
voltage
Maximum
voltage
% of rated voltage
70% max.
10% min.
150%
at 23°C
Power
consumption
(mW)
Approx. 360
Low-sensitivity Non-latching 4PDT (G6A-474P-ST40-US - DISCONTINUED)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance
(ref. value) (H)
Armature
OFF
Pick-up
voltage
Armature
ON
3
133.30
22.50
0.035
0.02
4.5
88.9
50.6
0.1
0.07
5
80
62.50
0.12
0.09
6
66.70
90
0.17
0.13
9
44.30
203
0.42
0.30
12
33.30
360
0.70
0.52
24
16.70
1,440
2.80
2.20
48
8.30
5,760
10.20
8.60
Dropout
voltage
Maximum
voltage
% of rated voltage
70% max.
10% min.
150%
at 23°C
Power
consumption
(mW)
Approx. 400
Standard Single Coil Latching DPDT (G6AU-274P-ST-US)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance
(ref. value) (H)
Armature OFF
Set pick-up
voltage
Armature ON
3
33.70
89
0.15
0.11
4.5
22.2
202
0.34
0.25
5
20
250
0.44
0.35
6
16.70
360
0.64
0.48
9
11.10
810
1.38
1.07
12
8.30
1,440
2.50
2
24
4.20
5,760
9.20
7.20
48
2.50
19,000
28.50
22
Reset pickup voltage
Maximum
voltage
% of rated voltage
70% max.
70% min.
200%
at 23°C
Power
consumption
(mW)
Approx. 100
Approx. 120
Standard Dual Coil Latching DPDT (G6AK-274P-ST-US)
Rated
Rated
Coil
voltage current resistance
(VDC)
(mA)
(Ω)
Coil inductance
(ref. value) (H)
Set coil
Reset coil
Set
pick-up
voltage
Armature Armature Armature Armature
OFF
ON
OFF
ON
3
66.70
45
0.037
0.027
0.027
0.037
4.5
40.2
112
0.09
0.065
0.065
0.09
5
36
139
0.11
0.08
0.08
0.11
6
30
200
0.16
0.12
0.12
0.16
9
20
450
0.38
0.28
0.28
0.38
12
15
800
0.60
0.45
0.45
0.60
24
7.50
3,200
2.10
1.50
1.50
2.10
48
4.20
11,520
8.50
6.30
6.30
8.50
Reset
pick-up
voltage
Maximum
voltage
Power
consumption
(mW)
% of rated voltage
70% max.
70% min.
200%
at 23°C
Approx. 200
Approx. 180
Approx. 200
Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.
2. Operating characteristics are measured at a coil temperature of 23°C.
3. The maximum voltage is the highest voltage that can be imposed on the relay coil.
Low Signal Relay
G6A
83
Low-sensitivity Dual Coil Latching DPDT (G6AK-274P-ST40-US)
Rated
Coil
Rated
voltage current resistance
(mA)
(Ω)
(VDC)
Coil inductance (ref. value) (H)
Set coil
Reset coil
Set
pick-up
voltage
Armature Armature Armature Armature
OFF
ON
OFF
ON
3
120
25
0.015
0.01
0.01
0.015
4.5
79.9
56.3
0.04
0.025
0.025
0.04
5
72.50
69
0.05
0.035
0.035
0.05
6
60
100
0.07
0.05
0.05
0.07
9
40
225
0.16
0.12
0.12
0.16
12
30
400
0.28
0.20
0.20
0.28
24
15
1,600
1.10
0.75
0.75
1.10
48
7.50
6,400
4
2.90
2.9
4
Reset
pick-up
voltage
Maximum
voltage
Power
consumption
(mW)
% of rated voltage
70% max.
70% min.
150%
at 23°C
Approx. 360
Standard Single Coil Latching 4PDT (G6AU-474P-ST-US - DISCONTINUED)
Rated
voltage
(VDC)
Rated
current
(mA)
Coil
resistance
(Ω)
Coil inductance (ref. value) (H)
Armature OFF
Set pick-up
voltage
Armature ON
3
106.80
28.10
0.03
0.02
4.5
71.2
63.2
0.06
0.04
5
64
78.10
0.08
0.06
6
53.30
112.50
0.11
0.08
9
35.60
253
0.25
0.18
12
26.70
450
0.45
0.32
24
13.30
1,800
1.80
1.30
48
6.70
7,200
7.00
5.20
Reset pick-up
voltage
Maximum
voltage
% of rated voltage
70% max.
70% min.
150%
at 23°C
Power
consumption
(mW)
Approx. 320
Standard Dual Coil Latching 4PDT (G6AK-474P-ST-US - DISCONTINUED)
Rated
voltage
(VDC)
Rated
Coil
current resistance
(mA)
(Ω)
Coil inductance (ref. value) (H)
Set coil
Reset coil
Set
pick-up
voltage
Armature Armature Armature Armature
OFF
ON
OFF
ON
3
106.80
28.10
0.03
0.02
0.02
0.03
4.5
71.2
63.2
0.06
0.04
0.04
0.06
5
64
78.10
0.08
0.06
0.06
0.08
6
53.30
112.50
0.11
0.08
0.08
0.11
9
35.60
253
0.25
0.18
0.18
0.25
12
26.70
450
0.45
0.32
0.32
0.45
24
13.30
1,800
1.80
1.30
1.30
1.80
48
6.70
7,200
7.00
5.20
5.20
7.00
Reset
pick-up
voltage
Maximum
voltage
Power
consumption
(mW)
% of rated voltage
70% max.
70% min.
150%
at 23°C
Approx. 320
Dual Coil Latching Low-sensitivity 4PDT (G6AK-474P-ST40-US - DISCONTINUED)
Rated
voltage
(VDC)
Rated
Coil
current resistance
(mA)
(Ω)
Coil inductance (ref. value) (H)
Set coil
Reset coil
Set
pick-up
voltage
Armature Armature Armature Armature
OFF
ON
OFF
ON
3
120
25
0.02
0.02
0.02
0.02
4.5
79.9
56.3
0.045
0.035
0.035
0.045
5
72.50
69
0.065
0.05
0.05
0.065
6
60
100
0.09
0.075
0.075
0.09
9
40
225
0.18
0.14
0.14
0.18
12
30
400
0.30
0.23
0.23
0.30
24
15
1,600
1.20
0.82
0.82
1.20
48
7.50
6,400
4.40
3.20
3.20
4.40
Reset
pick-up
voltage
Maximum
voltage
% of rated voltage
70% max.
70% min.
150%
at 23°C
Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.
2. Operating characteristics are measured at a coil temperature of 23°C.
3. The maximum voltage is the highest voltage that can be imposed on the relay coil.
84
Low Signal Relay
G6A
Power
consumption
(mW)
Approx. 360
■ Characteristics
Type
Non-latching
Contact resistance (See note 1)
50 mΩ max.
Operate (set) time
(See note 2)
5 ms max. (mean value approx. 3 ms)
Release (reset) time
(See note 2)
DPDT
4PDT - DISCONTINUED 7 ms max. (mean value approx 3.80 ms)
DPDT
Latching
5 ms max. (mean value approx. 2.50 ms)
7 ms max. (mean value approx. 3.30 ms)
3 ms max. (mean value approx. 1.20 ms)
5 ms max. (mean value approx. 2.50 ms)
4PDT - DISCONTINUED 5 ms max. (mean value approx. 1.30 ms)
7 ms max. (mean value approx. 2.70 ms)
Min. set/reset signal width DPDT
7 ms min.
4PDT - DISCONTINUED 15 ms min.
Operating frequency
Mechanical
36,000 operations/hour
Electrical
1,800 operations/hour (under rated load)
Insulation resistance (See note 3)
1,000 MΩ min. (at 500 VDC); except for set-reset
Dielectric strength
1,000 VAC, 50/60 Hz for 1 minute between coil and contacts
1,000 VAC, 50/60 Hz for 1 minute between contacts of different poles
1,000 VAC, 50/60 Hz for 1 minute between contacts of same pole
250 VAC, 50/60 Hz for 1 minute between set and reset coils
1,500 V (10 x 160 μs) (conforms to FCC Part 68)
Surge withstand voltage
Vibration
Mechanical durability 10 to 55 Hz; 5 mm double amplitude
Shock
Mechanical durability 1,000 m/s2 (Approx. 100G
Malfunction durability 10 to 55 Hz; 3.3 mm double amplitude
Malfunction durability DPDT: 500 m/s2 (Approx. 50 G); 4PDT: 300 m/s2 (Approx. 30 G)
Ambient temperature
-40° to 70°C with no icing
Humidity
5% to 85% RH
Service life
Weight
Mechanical
100 million operations min. (at 36,000 operations/hour)
Electrical
500,000 operations min. (at 1,800 operations/hr) See “Characteristic Data”
DPDT
Approx. 3.5 g
4PDT - DISCONTINUED Approx. 6.0 g
Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a fall-of-potential method.
2. Values in parentheses are typical values unless otherwise stated.
3. The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength
(except between the set and reset coil).
4. The above values are initial values.
■ Approvals
UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C
Type
G6A( )-274P-ST( )-US
Contact form
DPDT
Coil rating
1.5 to 48 VDC
Contact ratings
1 A at 125 VAC (General Purpose)
2 A at 30 VDC (General Purpose)
0.6 A at 110 VDC (General Purpose)
Number of test operations
6,000
Note: 1. The rated values approved by each of the safety standards (e.g., UL and CSA) may be different from the performance characteristics
individually defined in this catalog.
2. In the general interest of product improvement, specifications are subject to change.
Low Signal Relay
G6A
85
■ Characteristic Data
Ambient Temperature vs.
Maximum Coil Voltage
Switching current (A)
DC inductive
(L/R = 7 ms)
DC resistive
AC resistive
AC inductive
(cosf = 0.4)
Maximum coil voltage (%)
Maximum Switching Capacity
DPDT, 4PDT
DPDT: 100, 180, 200 mW
DPDT: 360, 400 mW
4PDT: 320, 360, 400 mW
Rated Operating voltage (V)
Ambient temperature (°C)
Note: The maximum coil voltage refers
to the maximum value in a varying
range of operating power voltage,
not a continuous voltage.
100
50
20
4PDT
-274P 30 VDC, resistive
-234P 30 VDC, resistive;
-274P 30 VDC, inductive
10
5
3
-234P 125 VAC,
resistive
1
0.5
0.3
-274P 125 VAC,
resistive;
-234P 30 VDC,
inductive
0.1
0.05
0.03
234P 125 VAC,
inductive
-274P 125 VAC,
inductive
Rated operating current (A)
Note: G6A-4 pole versions are discontinued.
86
Low Signal Relay
G6A
Service Life (x10 6 operations)
Service Life (x10 6 operations)
Electrical Service Life
DPDT
100
50
30
10
5
3
-474P 30 VDC, resistive
-434P 30 VDC, resistive,
-434P 30 VDC, inductive
-474P 30 VDC, inductive
1
0.5
0.3
0.1
0.05
0.03
-434P 125 VAC,
resistive
-434P 125 VAC, -474P 125 VAC,
inductive
inductive
Rated Operating current (A)
Dimensions
Note: 1. All units are in millimeters unless otherwise indicated.
2. Orientation marks are indicated as follows:
■ Non-latching
G6A-274P-ST(40)-US
10.1 max.
(9.9)*
20.2 max.
(20)*
Mounting Holes
(Bottom View)
Tolerance: ±0.1
Terminal Arrangement/
Internal Connections
(Bottom View)
1+
6
16-
13
11
0.3
7.62
(1.2)
8
4
8.4 max.
0.64 (8.2)*
5.08 5.08
(1.2)
7.62
9
(1.2)
3.16
0.6
7.62
(1.2)
Eight, 1.0-dia. holes
*Average value
G6A-474P-ST-US - DISCONTINUED
Terminal Arrangement/
Internal Connections
(Bottom View)
10.1 max.
(9.9)*
35.4 max.
(35.2)*
7
1
3
5
8
+
8.4 max.
0.64 (8.2)*
0.3
0.6
12
14
10
4
6
13
11
16
9
Mounting Holes
(Bottom View)
Tolerance: ±0.1
3.16
7.62
*Average value
5.08 5.08 5.08
(1.2)
7.62
5.08 5.08
(1.2)
7.62
(1.2)
(1.2)
Fourteen, 1.0-dia. holes
■ Latching
G6AU-274P-ST-US
10.1 max.
(9.9)*
20.2 max.
(20)*
8.4 max.
0.64 (8.2)*
1
8
+ SR
0.6
0.3
Mounting Holes
(Bottom View)
Terminal Arrangement/
Internal Connections
(Bottom View)
3.16
16
-+
Tolerance: ±0.1
(1.2)
7.62
5.08 5.08
(1.2)
6
4
13
7.62
11
9
(1.2)
7.62
*Average value
(1.2)
Eight, 1.0-dia. holes
Low Signal Relay
G6A
87
G6AK-274P-ST(40)-US
Terminal Arrangement/
Internal Connections
(Bottom View)
10.1 max.
(9.9)*
20.2 max.
(20)*
8.4 max.
0.64 (8.2)*
1+ +
Mounting Holes
(Bottom View)
Tolerance: ±0.1
2
2.54 5.08 5.08 5.08
(1.2)
8
(1.2)
6
4
S R
0.3
0.6
3.16
16 -
- 15
7.62
13
11
9
(1.2)
7.62
(1.2)
*Average value
Ten, 1-dia. holes
G6AU-474P-ST-US - DISCONTINUED
Terminal Arrangement/
Internal Connections
(Bottom View)
10.1 max.
(9.9)*
35.4 max.
(35.2)*
7
8.4 max.
0.64 (8.2)*
3
5
12
0.6
8
4
+ S R
- +
14
13
16
10
0.3
1
6
11
9
3.16
7.62
*Average value
Mounting Holes
(Bottom View)
Tolerance: ±0.1
5.08 5.08 5.08
(1.2)
7.62
5.08 5.08
(1.2)
7.62
(1.2)
(1.2)
Fourteen, 1.0-dia. holes
G6AK-474P-ST(40)-US - DISCONTINUED
Terminal Arrangement/
Internal Connections
(Bottom View)
10.1 max.
(9.9)*
35.4 max.
(35.2)*
7
5
12
10
0.6
4
+
R
S
14
13
16 15
+
8.4 max.
0.64 (8.2)*
0.3
1 2
3
3.16
8
6
11
9
Mounting Holes
(Bottom View)
7.62
Tolerance: ±0.1
*Average value
5.08 5.08 5.08 2.54 5.08 5.08 5.08
(1.2)
7.62
(1.2)
Sixteen, 1.0-dia. holes
(1.2)
Precautions
Long-term Continuously ON Contacts
Relay Handling
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout. Otherwise, use a latching relay.
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold cleaning bath immediately after soldering.
88
Low Signal Relay
G6A
Omron Electronic Components, LLC
Terms and Conditions of Sales
I. GENERAL
1. Definitions: The words used herein are defined as follows.
(a) Terms:
These terms and conditions
(b) Seller:
Omron Electronic Components LLC and its subsidiaries
(c) Buyer:
The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Terms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
II. SALES
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
III. PRECAUTIONS
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
IV. WARRANTY AND LIMITATION
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
V. INFORMATION; ETC.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information.
VI. MISCELLANEOUS
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
Low Signal Relay
G6A
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
Global - http://www.omron.com
USA - http://www.components.omron.com
847-882-2288
Cat. No. X301-E-1
Low Signal Relay
06/09
G6A
Specifications subject to change without notice
Printed in USA