LED Control IC W2RF002RF Most Suitable IC for Controlling LED Effects within Applications • Free-running PWM gradation control, with up to 1,024 levels, enables the representation of beautiful fade-in and fade-out effects. • CPU load can be reduced by controlling lighting gradation and speed. • Up to 49 pieces of this IC can be connected on the same serial bus communication line. Device group setting is also possible. • 24 Line Outputs are contained in the 7 x 7 mm package. • Use with Omron’s W2RV005RM Constant Current IC to directly drive multiple LED’s in series. • RoHS Compliant Ordering Information Description LED Control IC Model W2RF002RF Specifications Absolute Maximum Ratings (Ta = 25°C) Recommended Operating Conditions Item Symbol Rating Supply Voltage Input Voltage Communication Output Voltage (SCL-O, SDA-O) Driving Output Voltage VDD VIN -0.3 to 7.0 V -0.3 to VDD + 0.3 ≤ 7.0 V Item VSOUT -0.3 to VDD + 0.3 ≤ 7.0 V VDOUT Driving Output Current/pin (See note 1) IDOUT Power Dissipation Operating Temperature Storage Temperature Pd TOPR TSTG -0.3 to 20 V 50 mA (when VDD = 5.0 V) 30 mA (when VDD = 3.3 V) 1.19 W (See note 2) -20 to 85 °C -40 to 150 °C Symbol Rating VDD VIN 3.0 to 5.5 V 0 to VDD V ISOUT -10 to 10 mA fSCL Max. 5 MHz (See note 1) Supply Voltage Input Voltage Communication Output Current (SCL-O, SDA-O) Communication Clock Frequency (SCL-I) Note: 1. Take the timing characteristics into consideration. Note: 1. Take the power consumption and power dissipation rating into consideration. 2. When implemented on a standard board (70 x 70 x 1.6 mm, Cu 3%, Single-sided glass epoxy board). The value reduces at a rate of about 9.52 mW/°C when the IC is used at Ta = 25°C or higher. DC Electrical Characteristics (Ta = 25°C, VDD = 5V) Item Symbol Condition High-level Input Voltage VIH Low-level Input Voltage VIL High-level Communication Output Voltage Low-level Communication Output Voltage Spec. Max. Unit Min. Typ. --- VDD x 0.7 --- --- V --- --- --- VDD x 0.3 V VSOH IOUT = -10 mA VDD - 0.5 --- --- V VSOL IOUT = 10 mA --- --- 0.5 V Applicable terminal SDA-I, SCL-I, RST, INV, ADRA0 to 2, ADRB0 to 2 SDA-O, SCL-O Driving Output Voltage 1 VDO1 IOUT = 50 mA --- 0.27 0.60 V Driving Output Voltage 2 VDO2 IOUT = 20 mA --- 0.10 0.22 V Driving Output Leakage Current IDOZ VOUT = 5 V --- --- 1.0 μA Operating Current Consumption IDD Total Output: IOUT = 50 mA --- 3.2 5.3 mA LED Control IC OUTA0 to 7 OUTB0 to 7 OUTC0 to 7 W2RF002RF VDD 1 Timing Characteristics (Ta = 25°C, VDD = 5V) Item Symbol Condition Driving Output PWM Cycle TPWM Communication Clock Pulse Width Spec. Unit Applicable terminal 4.12 ms OUTA0 to 7 OUTB0 to 7 OUTC0 to 7 --- --- ns SCL-I 50 --- --- ns 50 --- --- ns Min. Typ. Max. --- 3.88 4.00 tSCL --- 100 Setup Time tSET --- Hold Time tHLD --- tSCL SDA-I, SCL-I tSCL SCL-I tSET tHLD Valid SDA-I Fig. 1 Input timing waveforms Engineering Data Block Diagram VZ1 INV VZ2 SDA-I SCL-I Filter Filter Gradation control A0 Communication circuit Register SDA-O SCL-O Buffer Gradation control C0 Buffer ADRA2 Operational control ADRA1 Gradation control B0 ADRA0 ADRB2 OUTA0 OUTB0 Output circuit OUTC0 OUTA1 OUTB1 OUTC1 Gradation control A1 OUTA2 Gradation control B1 OUTC2 Gradation control C1 OUTB3 Gradation control A7 OUTA6 Gradation control B7 OUTC6 Gradation control C7 OUTB7 ADRB1 OUTB2 OUTA3 OUTC3 ADRB0 RST Filter Reset CAP VDD Internal oscillation Clock division circuit GND System clock 2 LED Control IC W2RF002RF OUTB6 OUTA7 OUTC7 Terminal Designation Terminal Number Terminal Name Description I/O 1 SDA-I Serial data input I 2 SCL-I Serial clock input I 3 RST Reset (See note 1) I 4 VDD Power source P 5 CAP Capacitor (See note 2) --- 6 GND Ground P 7 ADRA2 Device address A2 I 8 ADRA1 Device address A1 I 9 ADRA0 Device address A0 I 10 ADRB2 Device address B2 I 11 ADRB1 Device address B1 I 12 ADRB0 Device address B0 I 13 INV Output inversion I 14 GND Ground P 15 OUTA0 Output A0 O 16 OUTB0 Output B0 O 17 OUTC0 Output C0 O 18 OUTA1 Output A1 O 19 OUTB1 Output B1 O 20 OUTC1 Output C1 O 21 VZ1 Output protection 1(See note 3) --- 22 GND Ground P 23 OUTA2 Output A2 O 24 OUTB2 Output B2 O 25 OUTC2 Output C2 O 26 OUTA3 Output A3 O 27 OUTB3 Output B3 O 28 OUTC3 Output C3 O 29 GND Ground P 30 OUTA4 Output A4 O 31 OUTB4 Output B4 O 32 OUTC4 Output C4 O 33 OUTA5 Output A5 O 34 OUTB5 Output B5 O 35 OUTC5 Output C5 O 36 GND Ground P 37 VZ2 Output protection 2(See note 3) --- 38 OUTA6 Output A6 O 39 OUTB6 Output B6 O 40 OUTC6 Output C6 O 41 OUTA7 Output A7 O 42 OUTB7 Output B7 O 43 OUTC7 Output C7 O 44 GND Ground P 45 TST1 Not used (See note 4) --- 46 TST2 Not used (See note 4) --- 47 SDA-O Serial data buffer output O 48 SCL-O Serial clock buffer output O Logic Function CMOS, filter L: Reset CMOS, filter, pull-up Refer to Operaton section (See note 4) CMOS N-ch open drain N-ch open drain N-ch open drain N-ch open drain CMOS Note: 1. The RST terminal is connected to an internal 100 kΩ pull-up resistor. When this terminal is not used, connect a 0.1 μF capacitor between the terminal and ground to prevent misoperation at power-on. 2. Connect the CAP terminal to a capacitor for smoothing power supply. Connect a 0.1 μF capacitor between the terminal and GND. 3. The VZ1 and VZ2 terminals are for driving output protection. Connect them to the power source of a driving system. When several driving system power supplies are used, connect the terminals to the highest potential among them. When these terminals are not used, leave them open. 4. Always leave the TST1 and TST2 terminals open. 5. Leave unused output terminals open. LED Control IC W2RF002RF 3 Operation ■ Functional Overview Receiving Commands The IC recieves commands with two-wire serial communication to control 24 LED lines. Commands are received in a 40-bits-per-command communication format. Gradation Control The lighting of the 24 LED lines is controlled individually or by group with 16-level lighting gradation and 32-level lighting speed. The exponential control of output duty cycle allows lighting gradation that matches the human visual characteristics. In addition, the specification of lighting speed allows fade-in and fade-out with up to 1,024 levels. Number of Control Lines The IC has two device address lines, each of which can be configured in seven ways by terminal configuration. This provides up to 49 patterns of device address configuration, allowing up to 1,176 lines to be controlled on the same communication line. Two device address lines can be combined to configure a device group. ■ Communication Specifications Input signals to SDA-I and SCL-I are input via the filter circuit (0.1μs delay) to the communication circuit. An SDA-I signal that is input to the communication circuit is taken in as serial data at the rising edge of an SCL-I signal. When serial data is received in a different format from the communication format, the data will be invalid. When the START signal, “111111111” is detected, the communication circuit takes in data as new serial data, whether it is on stand-by or in the middle of intake of serial data. Input signals to SDA-I and SCL-I will be output via the asynchronous buffer to SDA-O and SCL-O without going through the filter circuit. Communication Format 4 5 1 1 1 1 1 1 Name 6 7 8 1 1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 1 0 START 0 0 Device ID 0 Device address A Device address B Device selection data dvc_dat[7:0] 0 Output address Control data ctrl_dat[6:0] (Break) 3 Control 2 (Break) 1 (Break) bit SCL-I SDA-I 0 Lighting speed Lighting gradation Lighting data light_dat[8:0] X X X END Description of Communication Format Device ID Device Selection Data Device-specific ID (Fixed to “00” for this IC) Device Address A Specified with the ADRA0 to 2 terminals Device Address B Specified with the ADRB0 to 2 terminals Control Data Specifies control (data saving / immediate reflection) Control Lighting Data Output Address Specifies the terminal to output (Individual specification and collective specification are possible) Lighting Speed Specifies changing speed of free-running gradation control (32 levels) Lighting Gradation Specifies the brightness of lighting (16 levels) ■ Control Command Device Selection Data (8 bits) Device selection data dvc_dat (7:0) Device ID 0 Device Address A 0 ADRA2 ADRA1 Device Address B ADRA0 ADRB2 ADRB1 ADRB0 The device ID is fixed. The correspondence between the device addresses A and B and the setting terminals ADRA0 to 2 and ADRB0 to 2 is shown in the table. (Setting “L”...Data “0”. Setting “H”...Data “1”). When ADRA0 to 2 = “111”, the device address A line is specified collectively, and when ADRB0 to 2 = “111”, the device address B line is specified collectively. Because up to 7 addresses can be specified for each of device address A and device address B, their combination allows the specification of up to 49 addresses. 4 LED Control IC W2RF002RF Control Data (7 bits) Control data ctrl_dat (6:0) Control Output Address ctrl o_adr(5) o_adr(4) o_adr(3) o_adr(2) o_adr(1) o_adr(0) The control signal, ‘ctrl’, activates the operational control shown in the following table. • When ctrl = “0”, latch operation is activated, in which data is only stored in latch registers and will not be reflected in the output. • When ctrl = “1”, load operation is activated, in which data is stored in the specified latch registers and the data of the latch registers in all addresses will be stored in the load registers. Control (ctrl) Operational Control 0 Latch 1 Load The output terminals in the following table are specified with the output address o_adr(5:0) Output Address o_adr (5:0) Output Address o_adr (5:0) Output Terminal (5) (4) (3) (2) (1) (0) Output Terminal (5) (4) (3) (2) (1) (0) 0 0 0 0 0 0 OUTA0 1 0 0 0 0 0 OUTA0, OUTA1, OUTA4, OUTA5 0 0 0 0 0 1 OUTA1 1 0 0 0 0 1 OUTA2, OUTA3, OUTA6, OUTA7 0 0 0 0 1 0 OUTA2 1 0 0 0 1 0 OUTB0, OUTB1, OUTB4, OUTB5 0 0 0 0 1 1 OUTA3 1 0 0 0 1 1 OUTB2, OUTB3, OUTB6, OUTB7 0 0 0 1 0 0 OUTA4 1 0 0 1 0 0 OUTC0, OUTC1, OUTC4, OUTC5 0 0 0 1 0 1 OUTA5 1 0 0 1 0 1 OUTC2, OUTC3, OUTC6, OUTC7 0 0 0 1 1 0 OUTA6 0 0 0 1 1 1 OUTA7 1 0 0 1 1 0 0 0 1 0 0 0 OUTB0 OUTA0, OUTA1, OUTA4, OUTA5 OUTB0, OUTB1, OUTB4, OUTB5 OUTC0, OUTC1, OUTC4, OUTC5 0 0 1 0 0 1 OUTB1 1 0 0 1 1 1 0 0 1 0 1 0 OUTB2 OUTA2, OUTA3, OUTA6, OUTA7 OUTB2, OUTB3, OUTB6, OUTB7 OUTC2, OUTC3, OUTC6, OUTC7 0 0 1 0 1 1 OUTB3 1 0 1 0 0 0 OUTA0, OUTA1, OUTA2, OUTA3 0 0 1 1 0 0 OUTB4 1 0 1 0 0 1 OUTA4, OUTA5, OUTA6, OUTA7 0 0 1 1 0 1 OUTB5 1 0 1 0 1 0 OUTB0, OUTB1, OUTB2, OUTB3 0 0 1 1 1 0 OUTB6 1 0 1 0 1 1 OUTB4, OUTB5, OUTB6, OUTB7 0 0 1 1 1 1 OUTB7 1 0 1 1 0 0 OUTC0, OUTC1, OUTC2, OUTC3 0 1 0 0 0 0 OUTC0 1 0 1 1 0 1 OUTC4, OUTC5, OUTC6, OUTC7 0 1 0 0 0 1 OUTC1 0 1 0 0 1 0 OUTC2 1 0 1 1 1 0 0 1 0 0 1 1 OUTC3 OUTA0, OUTA1, OUTA2, OUTA3 OUTB0, OUTB1, OUTB2, OUTB3 OUTC0, OUTC1, OUTC2, OUTC3 0 1 0 1 0 0 OUTC4 1 0 1 1 1 1 0 1 0 1 0 1 OUTC5 OUTA4, OUTA5, OUTA6, OUTA7 OUTB4, OUTB5, OUTB6, OUTB7 OUTC4, OUTC5, OUTC6, OUTC7 0 1 0 1 1 0 OUTC6 1 1 0 0 0 0 OUTA0, OUTB0, OUTC0 0 1 0 1 1 1 OUTC7 1 1 0 0 0 1 OUTA1, OUTB1, OUTC1 0 1 1 0 0 0 OUTA0, OUTA2, OUTA4, OUTA6 1 1 0 0 1 0 OUTA2, OUTB2, OUTC2 0 1 1 0 0 1 OUTA1, OUTA3, OUTA5, OUTA7 1 1 0 0 1 1 OUTA3, OUTB3, OUTC3 0 1 1 0 1 0 OUTB0, OUTB2, OUTB4, OUTB6 1 1 0 1 0 0 OUTA4, OUTB4, OUTC4 0 1 1 0 1 1 OUTB1, OUTB3, OUTB5, OUTB7 1 1 0 1 0 1 OUTA5, OUTB5, OUTC5 0 1 1 1 0 0 OUTC0, OUTC2, OUTC4, OUTC6 1 1 0 1 1 0 OUTA6, OUTB6, OUTC6 0 1 1 1 0 1 OUTC1, OUTC3, OUTC5, OUTC7 1 1 0 1 1 1 OUTA7, OUTB7, OUTC7 1 1 1 0 0 0 (No terminal) 0 OUTA0, OUTA2, OUTA4, OUTA6 OUTB0, OUTB2, OUTB4, OUTB6 OUTC0, OUTC2, OUTC4, OUTC6 1 1 1 0 0 1 All OUTA 1 1 1 0 1 0 All OUTB 1 1 1 0 1 1 All OUTA, All OUTB 1 1 1 1 0 0 All OUTC 1 1 1 1 0 1 All OUTA, All OUTC 1 1 1 1 1 0 All OUTB, All OUTC 1 1 1 1 1 1 All OUTA, All OUTB, All OUTC 0 0 1 1 1 1 1 1 1 1 1 OUTA1, OUTA3, OUTA5, OUTA7 OUTB1, OUTB3, OUTB5, OUTB7 OUTC1, OUTC3, OUTC5, OUTC7 LED Control IC W2RF002RF 5 Lighting Data (9 bits) Lighting data light_dat (8:0) Lighting speed spd(4) spd(3) spd(2) Lighting gradation spd(1) spd(0) brt(3) brt(2) brt(1) brt(0) Lighting is controlled in each line with the values of the load registers. In lighting control, the gradation changes to the specified one at the specified lighting speed The Lighting speed follows the table below. The change time is specified with 5 bits; Lighting Speed spd(4:0) (4) (3) (2) (1) (0) The Lighting gradation follows the table below. The brightness is specified with 4 bits; Change time per 1/15 of brightness Change time from 0/15 to 15/15 of brightness (and vice versa) Lighting Gradation brt(3:0) (3) (2) (1) (0) Brightness PWM duty ratio (reference) 0 0 0 0 0 Less than 60 μs Less than 1 ms 0 0 0 0 0/15 (light OFF) 0% 0 0 0 0 1 8.5 ms 0.128 s 0 0 0 1 1/15 0.42 % 0 0 0 1 0 10.7 ms 0.160 s 0 0 1 0 2/15 0.84 % 0 0 0 1 1 12.8 ms 0.192 s 0 0 1 1 3/15 1.25 % 0 0 1 0 0 14.9 ms 0.224 s 0 1 0 0 4/15 1.78 % 0 0 1 0 1 17.1 ms 0.256 s 0 1 0 1 5/15 2.61 % 0 0 1 1 0 21.3 ms 0.320 s 0 1 1 0 6/15 3.76 % 0 0 1 1 1 25.6 ms 0.384 s 0 1 1 1 7/15 5.42 % 0 1 0 0 0 29.9 ms 0.448 s 1 0 0 0 8/15 7.96 % 0 1 0 0 1 34.1 ms 0.512 s 1 0 0 1 9/15 11.3 % 0 1 0 1 0 42.7 ms 0.640 s 1 0 1 0 10/15 16.7 % 0 1 0 1 1 51.2 ms 0.768 s 1 0 1 1 11/15 23.3 % 0 1 1 0 0 59.7 ms 0.896 s 1 1 0 0 12/15 35.2 % 0 1 1 0 1 68.3 ms 1.024 s 1 1 0 1 13/15 48.4 % 0 1 1 1 0 85.3 ms 1.280 s 1 1 1 0 14/15 73.4 % 0 1 1 1 1 102 ms 1.536 s 1 0 0 0 0 119 ms 1.792 s 1 15/15 (Light completely ON) 100 % 1 0 0 0 1 137 ms 2.048 s 1 0 0 1 0 171 ms 2.560 s 1 0 0 1 1 205 ms 3.072 s 1 0 1 0 0 239 ms 3.584 s 1 0 1 0 1 273 ms 4.096 s 1 0 1 1 0 341 ms 5.120 s 1 0 1 1 1 410 ms 6.144 s 1 1 0 0 0 478 ms 7.168 s 1 1 0 0 1 546 ms 8.192 s 1 1 0 1 0 683 ms 10.24 s 1 1 0 1 1 819 ms 12.29 s 1 1 1 0 0 956 ms 14.34 s 1 1 1 0 1 1,092 ms 16.38 s 1 1 1 1 0 1,365 ms 20.48 s 1 1 1 1 1 1,638 ms 24.58 s Note: The change time per 1/15 of brightness represents the time required for a change from, for example, 10/15 to 11/15 of brightness. The change time from 0/15 to 15/15 of brightness and vice versa represents the time required for a change from 0/15 of brightness (light OFF) to 15/15 of brightness (light completely ON). However, these times are median values and depend on the driving output PWM cycle. 6 LED Control IC W2RF002RF 1 1 1 ■ Functional Terminals/Setting Terminals ADR terminals The ADRA terminal and ADRB terminal set device address A and device address B, respectively. For “H” setting, connect the terminal to VDD and for “L” setting, connect the terminal to GND INV terminal This terminal sets the polarity of OUT terminal. • When the terminal is used with “L” as active (e.g., for directly driving an LED), connect the terminal to VDD RST terminal When the voltage of the RST terminal becomes “L”, the internal circuit will be reset and the output will be open. • When the terminal is used with the “H” as active (e.g., for driving an LED with a driving transistor), connect the terminal to GND. ■ Application Example 5V Transmitting circuit 12 V 1 SDA-I VZ1 21 2 SCL-I VZ2 37 R R Receiving circuit 48 SCL-O OUTA1 18 OUTB1 19 OUTC1 20 10 ADRB2 11 ADRB1 12 ADRB0 OUTA2 23 OUTB2 24 OUTC2 25 4 VDD C1 0.1μF 6 14 22 29 36 44 GND GND GND GND GND GND 3 RST 5 CAP NC 45 TST1 NC 46 TST2 B B G B R G 7 ADRA2 8 ADRA1 9 ADRA0 13 INV C2 0.1μF C3 0.1μF OUTA0 15 OUTB0 16 OUTC0 17 47 SDA-O R G G W2RF002RF B W2RV005RM OUTA3 26 OUTB3 27 OUTC3 28 OUTA4 30 OUTB4 31 OUTC4 32 OUTA5 33 OUTB5 34 OUTC5 35 OUTA6 38 OUTB6 39 OUTC6 40 OUTA7 41 OUTB7 42 OUTC7 43 LED Control IC W2RF002RF 7 Dimensions 1.6 (max.) 9 ± 0.2 7 ± 0.1 Trademark Recommended PCB Layout S 0.1 ± 0.05 1.5 ± 0.05 0.5 25 36 Type 37 24 48 13 0.08 S 12 +6º +0.05 0.22 -0.04 4º -4º 0.08 M 0.1 45 +0.0 5 -0.0 3 1(min) 1(min) 1 0.5 ± 0.1 0.5 ± 0.15 1 ± 0.2 Index mark 7.5 7 ± 0.1 9 ± 0.2 Lot No. 0.25 7.5 (Unit : mm) Tape Packaging Packaging style: Embossed taping Packaging quantity: 1,500 pcs/reel Reel Dimensions 9 . 5 ±0 . 1 1 0 . 8 ±0 . 1 7 . 5 ±0 . 1 1 . 7 ±0 . 1 17.5±1.0 1 . 5 ( m in ) (330) 2 2 . 5 ( m a x) ϕ1 . 6 +-00. 1 1 2 . 0 ±0 . 1 Direction of Insertion 9 . 8 ±0 . 1 (6.0) 9 . 5 ±0 . 1 No.1pin Reel Drawing direction 8 0 . 3 ±0 . 0 5 (6.0) 2 . 0 ±0 . 1 1 6 . 0 ±0 . 3 1 3 . 0 ±0 . 2 4 . 0 ±0 . 1 (80) ϕ 1 . 5 +-00. 1 1 . 7 5 ±0 . 1 Embossed Tape Dimensions ϕ 20.2(mi n) LED Control IC W2RF002RF (0.8) (1.4) 2.2±0.1 Precautions for Use ■ Correct Use ■ RoHS Directive Compliance • The absolute maximum rating is the limit value which should not be exceeded even in a flash. Exceeding this value can cause deterioration of the characteristics or complete failure of the IC. • Check the operation at the communication frequency to be used before using the device. • Sufficiently take into consideration the static electricity, chattering and voltage of the input to be connected when determining each input circuit. • Although the device contains an ESD protection circuit, static electricity that exceeds the function may damage the device. When handling the device, exercise due caution by, for example, grounding the human body. • Due to potential damage, do not use product that has been dropped or that has come into contact with water. Models that are indicated as being RoHS compliant are free of the following six substances. Lead: 1,000 ppm max. Mercury: 1,000 ppm max. Cadmium: 100 ppm max. Hexavalent chromium: 1,000 ppm max. PBB: 1,000 ppm max. PBDE: 1,000 ppm max. ■ Lot Code Indication ■ Recommended Reflow Conditions Control Code: Three-digit alphanumeric characters Allowable Temperature Profile Conditions Production week: Serial number starting from week01 including January1 Product mounting method should be by Reflow and we recommend the following temperature profile. Reflow no more than two times, maximum. Production year: The last one digit of the year Package surface temperature 260°C (max) 250°C 10s (max) 220°C 200°C 140°C 60~120s 60s (max) Time Storage Conditions before Mounting Moisture absorption by the plastic package will increase the possibility of faults, such as cracks; therefore, take enough care for storage. Storage Conditions Period 5 to 30°C, 40 to 70%RH One Year LED Control IC W2RF002RF 9 All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ON-LINE OMRON ELECTRONIC COMPONENTS LLC Global - http://www.omron.com USA - http://www.components.omron.com 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. OCB-AM AM-W2-AO-005(E) 10 LED Control IC 08/12 W2RF002RF Specifications subject to change without notice Printed in USA