TB62726ANG/AFG TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic TB62726ANG,TB62726AFG 16-bit Constant-Current LED Driver with Operating Voltage of 3.3-V and 5-V The TB62726A series are comprised of constant-current drivers designed for LEDs and LED displays. The output current value can be set using an external resistor. As a result, all outputs will have virtually the same current levels. This driver incorporates 16-bit constant-current outputs, a 16-bit shift register, a 16-bit latch and a 16-bit AND-gate circuit. These drivers have been designed using the Bi-CMOS process. The suffix (G) appended to the part number represents a Lead(Pb)-Free product. TB62726ANG TB62726AFG Features • Output current capability and number of outputs: 90 mA × 16 outputs • Constant current range: 2 to 90 mA • Application output voltage: 0.7 V (output current 2 to 80 mA) 0.4 V (output current 2 to 40 mA) • For anode-common LEDs • Input signal voltage level: 3.3-V and 5-V CMOS level (Schmitt trigger input) Weight SDIP24-P-300-1.78: 1.22 g (typ.) SSOP24-P-300-1.00B: 0.32 g (typ.) • Power supply voltage range VDD = 3.0 to 5.5 V • Maximum output terminal voltage: 17 V • Serial and parallel data transfer rate: 20 MHz (max, cascade connection) • Operating temperature range Topr = −40 to 85°C • Package: Type ANG: SDIP24-P-300-1.78 Type AFG: SSOP24-P-300-1.00B • Current accuracy (All output ON) Output Voltage Current Accuracy Between Bits > = 0.4 V > = 0.7 V ±4% Output Current Between ICs ±15% 2 to 5 mA ±12% 5 to 80 mA 1 2006-06-14 TB62726ANG/AFG Pin Assignment (top view) GND SERIAL-IN CLOCK VDD R-EXT SERIAL-OUT LATCH OUT0 OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 ENABLE OUT15 OUT14 OUT13 OUT12 OUT11 OUT10 OUT9 OUT8 Warnings: Short-circuiting an output terminal to GND or to the power supply terminal may broken the device. Please take care when wiring the output terminals, the power supply terminal and the GND terminals. Block Diagram OUT0 R-EXT OUT15 OUT1 I-REG ENABLE Q ST Q D ST Q D ST D LATCH D SERIAL-IN Q D CK Q CK D Q SERIAL-OUT CK CLOCK Truth Table CLOCK Note 1: LATCH ENABLE SERIAL-IN OUT0 … OUT7 … OUT15 SERIAL-OUT H L Dn Dn … Dn − 7 … Dn − 15 Dn − 15 L L Dn + 1 No change Dn − 14 H L Dn + 2 Dn + 2 … Dn − 5 … Dn − 13 Dn − 13 X L Dn + 3 Dn + 2 … Dn − 5 … Dn − 13 Dn − 13 X H Dn + 3 OFF Dn − 13 OUT0 to OUT15 = On when Dn = H; OUT0 to OUT15 = Off when Dn = L. In order to ensure that the level of the power supply voltage is correct, an external resistor must be connected between R-EXT and GND. 2 2006-06-14 TB62726ANG/AFG Timing Diagram n=0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3.3 V/5 V CLOCK 0V 3.3 V/5 V SERIAL-IN 0V 3.3 V/5 V LATCH 0V 3.3 V/5 V ENABLE 0V On OUT0 Off On OUT1 Off On OUT3 Off On OUT15 Off 3.3 V/5 V SERIAL-OUT 0V Warning: Latch circuit is leveled-latch circuit. Be careful because it is not triggered-latch circuit. Note 2: The latches circuit holds data by pulling the LATCH terminal Low. And, when LATCH terminal is a High level, latch circuit doesn’t hold data, and it passes from the input to the output. When ENABLE terminal is a Low level, output terminal OUT0 to OUT15 respond to the data, and on and off does. And, when ENABLE terminal is a High level, it offs with the output terminal regardless of the data. 3 2006-06-14 TB62726ANG/AFG Terminal Description Pin No. Pin Name 1 GND 2 SERIAL-IN 3 CLOCK 4 LATCH Function GND terminal for control logic Input terminal for serial data for data shift register Input terminal for clock for data shift on rising edge Input terminal for data strobe 5 to 20 When the LATCH input is driven High, data is not latched. When it is pulled Low, data is latched. OUT0 to OUT15 Constant-current output terminals Input terminal for output enable. 21 ENABLE All outputs ( OUT0 to OUT15 ) are turned off, when the ENABLE terminal is driven High. And are turned on, when the terminal is driven Low. 22 SERIAL-OUT 23 R-EXT 24 VDD Output terminal for serial data input on SERIAL-IN terminal Input terminal used to connect an external resistor. This regulated the output current. 3.3-V/5-V supply voltage terminal Equivalent Circuits for Inputs and Outputs 1. ENABLE terminal 2. LATCH terminal R (UP) VDD VDD LATCH ENABLE GND GND R (DOWN) 3. CLOCK, SERIAL-IN terminal 4. SERIAL-OUT terminal VDD VDD CLOCK, SERIAL-IN SERIAL-OUT Internal data GND GND 5. OUT0 to OUT15 terminals OUT0 to OUT15 Parasitic Diode GND 4 2006-06-14 TB62726ANG/AFG Absolute Maximum Ratings (Topr = 25°C) Characteristics Symbol Rating Unit Supply voltage VDD 6 V Input voltage VIN −0.2 to VDD + 0.2 V Output current IOUT +90 mA/ch Output voltage VOUT −0.2 to 17 V ANG-type (when not mounted) Power dissipation ANG-type (on PCB) (Note 3) AFG-type (when not mounted) 1.25 Pd1 1.78 W 0.83 Pd2 1.00 AFG-type (on PCB) ANG-type (when not mounted) Thermal resistance ANG-type (on PCB) (Note 3) AFG-type (when not mounted) 104 Rth (j-a) 1 70 °C/W 140 Rth (j-a) 2 120 AFG-type (on PCB) Operating temperature Topr −40 to 85 °C Storage temperature Tstg −55 to 150 °C Note 3: ANG-Type: Powers dissipation is derated by 14.28 mW/°C if device is mounted on PCB and ambient temperature is above 25°C. AFG-Type: Powers dissipation is derated by 6.67 mW/°C if device is mounted on PCB and ambient temperature is above 25°C. With device mounted on glass-epoxy PCB of less than 40% Cu and of dimensions 50 mm × 50 mm × 1.6 mm. Recommended Operating Conditions (Topr = −40°C to 85°C unless otherwise specified) Characteristics Symbol Conditions Min Typ. Max Unit Supply voltage VDD ⎯ 3 ⎯ 5.5 V Output voltage VOUT ⎯ Output current ⎯ 0.7 4 V IOUT Each DC 1 circuit 2 ⎯ 80 mA/ch IOH SERIAL-OUT ⎯ ⎯ −1 IOL SERIAL-OUT ⎯ ⎯ 1 0.7 × VDD ⎯ VDD + 0.15 −0.15 ⎯ 0.3 × VDD ⎯ ⎯ 20 MHz 50 ⎯ ⎯ ns 25 ⎯ ⎯ ns Upper IOUT = 20 mA 2000 ⎯ ⎯ Lower IOUT = 20 mA 3000 ⎯ ⎯ 10 ⎯ ⎯ ns 10 ⎯ ⎯ ns 50 ⎯ ⎯ ns VIH ⎯ Input voltage VIL Clock frequency fCLK LATCH pulse width twLAT CLOCK pulse width twCLK ENABLE pulse width (Note 4) Set-up time for CLOCK terminal Hold time for CLOCK terminal Set-up time for LATCH terminal twENA Cascade connected ⎯ tSETUP1 ⎯ tHOLD tSETUP2 mA V ns Note 4: When the pulse of the Low level is inputted to the ENABLE terminal held in the High level. 5 2006-06-14 TB62726ANG/AFG Electrical Characteristics (Topr = 25°C, VDD = 3.0 V to 5.5 V unless otherwise specified) Characteristics Supply voltage Symbol VDD IOUT1 VOUT = 0.7 V, VDD = 3.3 V IOUT4 VOUT = 0.7 V, VDD = 5 V ∆IOUT1 VOUT ≥ 0.4 V, All outputs ON REXT = 490 Ω ∆IOUT2 VOUT ≥ 0.4 V, All outputs ON REXT = 250 Ω IOZ VOUT = 15.0 V Max Unit 3.0 ⎯ 5.5 V 31.96 36.20 40.54 31. 59 35.90 40.20 63.63 72.30 80.97 62.75 71.30 79.95 ⎯ ±1 ±4 % µA mA REXT = 250 Ω ⎯ ⎯ 1 ⎯ ⎯ VDD ⎯ GND ⎯ 0.3 VDD IOL = 1.0 mA, VDD = 3.3 V ⎯ ⎯ 0.3 IOL = 1.0 mA, VDD = 5 V ⎯ ⎯ 0.3 IOH = − 1.0 mA, VDD = 3.3 V 3 ⎯ ⎯ IOH = 1.0 mA, VDD = 5 V 4.7 ⎯ ⎯ %/VDD When VDD is changed 3 V to 5.5 V ⎯ −1 −5 % R (Up) ENABLE terminal 115 230 460 kΩ VIN VOH Pull-down resistor Typ. 0.7 VDD SOUT terminal voltage Pull-up resistor Min REXT = 490 Ω IOUT3 VOL Output current Supply voltage Regulation VOUT = 0.4 V, VDD = 3.3 V VOUT = 0.4 V, VDD = 5 V Output current error between bits Input voltage Normal operation IOUT2 Output current Output leakage current input voltage Conditions R (Down) V LATCH terminal IDD (OFF) 1 VOUT = 15.0 V REXT = OPEN ⎯ 0.1 0.5 IDD (OFF) 2 VOUT = 15.0 V, All outputs OFF REXT = 490 Ω 1 3.5 5 IDD (OFF) 3 VOUT = 15.0 V, All outputs OFF REXT = 250 Ω 4 6 9 VOUT = 0.7 V, All outputs ON REXT = 490 Ω ⎯ 9 15 Same as the above, Topr = −40°C ⎯ ⎯ 20 VOUT = 0.7 V, All outputs ON ⎯ 18 25 ⎯ ⎯ 40 Supply current IDD (ON) 1 IDD (ON) 2 V REXT = 250 Ω Same as the above, Topr = −40°C 6 mA 2006-06-14 TB62726ANG/AFG Switching Characteristics (Topr = 25°C unless otherwise specifed) Characteristics Symbol Conditions CLK- OUTn , LATCH = “H”, tpLH1 Propagation delay ENABLE = “L” Min Typ. Max ⎯ 150 300 tpLH2 LATCH - OUTn , ENABLE = “L” ⎯ 140 300 tpLH3 ENABLE - OUTn , LATCH = “H” ⎯ 140 300 tpLH CLK-SERIAL OUT 3 6 ⎯ tpHL1 CLK- OUTn , LATCH = “H”, ENABLE = “L” ⎯ 170 340 tpHL2 LATCH - OUTn , ENABLE = “L” ⎯ 170 340 tpHL3 ENABLE - OUTn , LATCH = “H” ⎯ 170 340 tpLH CLK-SERIAL OUT 4 7 ⎯ Unit ns Output rise time tor 10 to 90% of voltage waveform 40 85 150 ns Output fall time tof 90 to 10% of voltage waveform 40 70 150 ns Maximum CLOCK rise time tr When not on PCB ⎯ ⎯ 5 µs ⎯ ⎯ 5 µs Maximum CLOCK fall time (Note 5) tf Conditions: (Refer to test circuit.) Topr = 25°C, VDD = VIH = 3.3 V and 5 V, VOUT = 0.7 V, VIL = 0 V, REXT = 490 Ω , VL = 3.0 V, RL = 60 Ω, CL = 10.5 pF Note 5: If the device is connected in a cascade and tr/tf for the waveform is large, it may not be possible to achieve the timing required for data transfer. Please consider the timings carefully. Test Circuit IDD VIH, VIL ENABLE RL VDD OUT0 CL Function generator CLOCK IOL OUT15 LATCH SERIAL-IN SERIAL-OUT R-EXT Logic input waveform VL GND CL Iref VDD = VIH = 3.3 V VIL = 0 V tr = tf = 10 ns (10% to 90%) 7 2006-06-14 TB62726ANG/AFG Timing Waveforms 1. CLOCK, SERIAL-IN, SERIAL-OUT twCLK 50% CLOCK 50% tSETUP1 SERIAL-IN 50% 50% tHOLD SERIAL-OUT 50% tpLH/tpHL 2. CLOCK, SERIAL-IN, LATCH , ENABLE , OUTn CLOCK 50% SERIAL-IN tSETUP2 LATCH 50% 50% twLAT ENABLE twENA 50% tSETUP3 OUTn 50% 50% tpHL1/LH1 tpHL2/LH2 tpHL3/LH3 3. OUTn 90% 90% OFF OUTn 10% 10% tof ON tor 8 2006-06-14 TB62726ANG/AFG Output Current – Duty (LEDS turn-on rate) IOUT – DUTY On PCB 80 80 (mA) 100 60 IOUT IOUT (mA) IOUT – DUTY On PCB 100 40 20 Topr = 25°C VDD = 3.3 V to 5.0 V 20 40 20 TB62726AFG VCE = 1.0 V Tj = 120°C (max) 0 0 60 60 DUTY – Turn On Rate 80 0 0 100 20 IOUT – DUTY On PCB (W/IC) PD 60 Power dissipation (mA) 80 100 80 100 (%) Pd – Topr 80 IOUT 60 2.0 1.8 40 Topr = 85°C VDD = 3.3 V to 5.0 V 20 NG (On PCB) 1.6 1.4 1.2 FG (On PCB) 1.0 0.8 0.6 0.4 TB62726AFG VCE = 1.0 V Tj = 120°C (max) 0 0 TB62726ANG 40 DUTY – Turn On Rate (%) 100 20 TB62726AFG VCE = 1.0 V Tj = 120°C (max) TB62726ANG 40 Topr = 55°C VDD = 3.3 V to 5.0 V 0.2 TB62726ANG 40 60 DUTY – Turn On Rate 80 0 0 100 20 40 60 Ambient temperature (%) Ta (°C) Output Current – REXT Resistor IOUT – REXT 90 Theoretical value: 80 IOUT = (1.15 (V) ÷ R-EXT (Ω)) × 14.9 70 IOUT (mA) 60 50 40 Topr = 25°C 30 20 10 VCE = 0.7 V 0 100 500 1000 5000 10000 REXT (Ω) 9 2006-06-14 TB62726ANG/AFG Application Circuit (example 1): The general composition in static lighting of LED. More than VLED (V) ≥ Vf (total max) + 0.7 is recommended with the following application circuit with the LED power supply VLED. r1: The setup resistance for the setup of output current of every IC. r2: The variable resistance for the brightness control of every LED module. Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system. VLED SCAN O0 O1 O2 O13 O14 SERIAL-IN SERIAL-OUT ENABLE C.U. 16-bit SIPO, Latches and Constant-sink-current drivers ENABLE O0 O15 SERIAL-IN LATCH O1 O2 O13 O14 O15 16-bit SIPO, Latches and Constant-sink-current drivers SERIAL-OUT LATCH TB62726ANG/AFG CLOCK CLOCK TB62726ANG/AFG r1 = 100 Ω (min) r2 r1 = 100 Ω (min) 10 2006-06-14 TB62726ANG/AFG Application Circuit (example 2): When the condition of VLED is VLED > 17 V The unnecessary voltage is one effective technique as to making the voltage descend with the zenor diode. Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system. VLED > 17 V SCAN O0 O1 O2 O13 O14 C.U. SERIAL-IN SERIAL-OUT ENABLE 16-bit SIPO, Latches and Constant-sink-current drivers ENABLE O0 O15 SERIAL-IN LATCH O1 O2 O13 O14 O15 16-bit SIPO, Latches and Constant-sink-current drivers SERIAL-OUT LATCH TB62726ANG/AFG CLOCK CLOCK TB62726ANG/AFG r1 = 100 Ω (min) r2 r1 = 100 Ω (min) 11 2006-06-14 TB62726ANG/AFG Application Circuit (example 3): When the condition of VLED is Vf +0.7 < VLED < 17 V VOUT = VLED-Vf = 0.7 to 1.0 V is the most suitable for VOUT. Surplus VOUT causes an IC fever and the useless consumption electric power. It is the one way of being effective to build in the r3 in this problem. r3 can make a calculation to the formula r3 Ω = surplus VOUT/IOUT. Though the resistance parts increase, the fixed constant current performance is kept Example) TD62M8600F: 8-bit multi-chip PNP transistor array, which is not used in static lighting system. r3 r3 VLED = 15 V SCAN O0 O1 O2 O13 O14 SERIAL-IN SERIAL-OUT C.U. 16-bit SIPO, Latches and Constant-sink-current drivers ENABLE O0 O15 SERIAL-IN LATCH O1 O2 O13 O14 O15 16-bit SIPO, Latches and Constant-sink-current drivers SERIAL-OUT LATCH TB62726ANG/AFG CLOCK CLOCK TB62726ANG/AFG r1 = 100 Ω (min) r2 r1 = 100 Ω (min) 12 2006-06-14 TB62726ANG/AFG Notes • Operation may become unstable due to the electromagnetic interference caused by the wiring and other phenomena. To counter this, it is recommended that the IC be situated as close as possible to the LED module. If overvoltage is caused by inductance between the LED and the output terminals, both the LED and the terminals may suffer damage as a result. • There is only one GND terminal on this device when the inductance in the GND line and the resistor are large, the device may malfunction due to the GND noise when output switchings by the circuit board pattern and wiring. To achieve stable operation, it is necessary to connect a resistor between the REXT terminal and the GND line. Fluctuation in the output waveform is likely to occur when the GND line is unstable or when a capacitor (of more than 50 pF) is used. Therefore, take care when designing the circuit board pattern layout and the wiring from the controller. • This application circuit is a reference example and is not guaranteed to work in all conditions. Be sure to check the operation of your circuits. • This device does not include protection circuits for overvoltage, overcurrent or overtemperature. If protection is necessary, it must be incorporated into the control circuitry. • The device is likely to be destroyed if a short-circuit occurs between either of the power supply pins and any of the output terminals when designing circuits, pay special attention to the positions of the output terminals and the power supply terminals (VDD and VLED), and to the design of the GND line. 13 2006-06-14 TB62726ANG/AFG Package Dimensions Weight: 1.22 g (typ.) 14 2006-06-14 TB62726ANG/AFG Package Dimensions Weight: 0.32 g (typ.) 15 2006-06-14 TB62726ANG/AFG Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. Timing Charts Timing charts may be simplified for explanatory purposes. 4. Application Circuits The application circuits shown in this document are provided for reference purposes only. Thorough evaluation is required, especially at the mass production design stage. Toshiba does not grant any license to any industrial property rights by providing these examples of application circuits. 5. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on Handling of ICs (1) The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. (2) Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. (3) If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. (4) Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 16 2006-06-14 TB62726ANG/AFG (5) Carefully select external components (such as inputs and negative feedback capacitors) and load components (such as speakers), for example, power amp and regulator. If there is a large amount of leakage current such as input or negative feedback condenser, the IC output DC voltage will increase. If this output voltage is connected to a speaker with low input withstand voltage, overcurrent or IC failure can cause smoke or ignition. (The over current can cause smoke or ignition from the IC itself.) In particular, please pay attention when using a Bridge Tied Load (BTL) connection type IC that inputs output DC voltage to a speaker directly. 17 2006-06-14 TB62726ANG/AFG Points to Remember on Handling of ICs (1) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (2) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor’s power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 18 2006-06-14 TB62726ANG/AFG About solderability, following conditions were confirmed • Solderability (1) Use of Sn-37Pb solder Bath · solder bath temperature = 230°C · dipping time = 5 seconds · the number of times = once · use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath · solder bath temperature = 245°C · dipping time = 5 seconds · the number of times = once · use of R-type flux RESTRICTIONS ON PRODUCT USE 060116EBA • The information contained herein is subject to change without notice. 021023_D • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. 021023_A • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. 021023_B • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 060106_Q • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C • The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E 19 2006-06-14