DATA SHEET MOS INTEGRATED CIRCUIT µPD17P228 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROLLER DESCRIPTION The µPD17P228 is a model of the µPD17228 with a one-time PROM instead of an internal mask ROM. Since the user can write programs to the µPD17P228, it is ideal for experimental production or small-scale production of the µPD17225, 17226, 17227 or 17228 systems. When reading this document, also read the documents related to the µPD17225, 17226, 17227 and 17228. Detailed functions are described in the following user's manual. Read this manual when designing your system. µPD172×× Series User's Manual: U12795E FEATURES • Pin compatible with µPD17225, 17226, 17227 and 17228 (except PROM programming function) • Carrier generator circuit for infrared remote controller (REM output) • 17K architecture: General-purpose register method • Program memory (one-time PROM): 16 Kbytes (8192 × 16) • Data memory (RAM): 223 × 4 bits • Pull-up resistor can be connected to RESET pin • Low-voltage detection circuit (WDOUT output) • Supply voltage: VDD = 2.2 to 3.6 V (fx = 4 MHz: high-speed mode, 4 µs) VDD = 3.0 to 3.6 V (fx = 8 MHz: high-speed mode, 2 µs) APPLICATIONS Preset remote controllers, toys, and portable systems ORDERING INFORMATION Part Number Package µPD17P228MC-5A4 30-pin plastic SSOP (7.62 mm (300)) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. U14542EJ1V0DS00 (1st edition) Date Published April 2000 N CP(K) Printed in Japan © 2000 µPD17P228 PIN CONFIGURATION (TOP VIEW) • 30-pin plastic SSOP (7.62 mm (300)) µPD17P228MC-5A4 (1) Normal oprating mode P0D2 1 30 IC2 P0D3 2 29 P0D1 INT 3 28 P0D0 P0E0 4 27 P0C3 P0E1 5 26 P0C2 P0E2 6 25 P0C1 P0E3 7 24 P0C0 REM 8 23 P0B3 VDD 9 22 P0B2 XOUT 10 21 P0B1 XIN 11 20 P0B0 GND 12 19 P0A3 RESET 13 18 P0A2 WDOUT 14 17 P0A1 IC1 15 16 P0A0 GND : Ground IC1, IC2 : Internally connected INT : External interrupt request signal input Note P0A0-P0A3 : Input port (CMOS input) P0B0-P0B3 : Input port (CMOS input) P0C0-P0C3 : Output port (N-ch open-drain output) P0D0-P0D3 : Output port (N-ch open-drain output) P0E0-P0E3 : I/O port (CMOS push-pull output) Note 2 REM : Remote controller output (CMOS push-pull output) RESET : Reset input VDD : Power supply WDOUT : Hang-up/low voltage detection output (N-ch open-drain output) XIN, XOUT : Resonator connection This pin cannot be used. Leave unconnected. Data Sheet U14542EJ1V0DS00 µPD17P228 (2) PROM programming mode D2 1 30 (Open) D3 2 29 D1 VPP 3 28 D0 4 27 D7 5 26 D6 6 25 D5 7 24 D4 (Open) 8 23 MD3 VDD 9 22 MD2 (Open) 10 21 MD1 CLK 11 20 MD0 GND 12 19 (L) 13 18 (Open) 14 17 (Open) 15 16 (L) (L) Caution Contents in parantheses indicate how to handle unused pins in PROM programming mode. L :Connect to GND via a resistor (470 Ω) separately. OPEN:Leave unconnected. CLK : Clock input for PROM D0 - D7 : Data input/output for PROM GND : Ground MD0 - MD3 : Mode select input for PROM VDD : Power supply VPP : Power supply for PROM writing Data Sheet U14542EJ1V0DS00 3 µPD17P228 BLOCK DIAGRAM P0A0 P0A1 P0A2 P0A3 P0A Remote Control Divider RF RAM 223 × 4 bits P0B0 (MD0) P0B1 (MD1) P0B2 (MD2) P0B3 (MD3) REM 8-bit timer SYSTEM REG. P0B Interrupt Controller INT (VPP) ALU P0C0 (D4) P0C1 (D5) P0C2 (D6) P0C3 (D7) P0C One Time PROM 8192 × 16 bits P0D0 (D0) P0D1 (D1) P0D2 (D2) P0D3 (D3) Instruction Decoder RESET P0D WDOUT Program Counter P0E0 P0E1 P0E2 P0E3 Power Supply Circuit P0E Stack (5 levels) Basic Interval/ Watchdog Timer Remark 4 ( ): during PROM programming mode Data Sheet U14542EJ1V0DS00 VDD GND CPU Clock XIN (CLK) OSC XOUT µPD17P228 CONTENTS 1. DIFFRENCES AMONG µPD17225, 17226, 17227, 17228 AND µPD17P228 .......................... 6 2. PIN FUNCTIONS .......................................................................................................................... 7 2.1 Normal Operation Mode .................................................................................................................... 7 2.2 PROM Programming Mode ............................................................................................................... 8 2.3 Input/Output Circuits ......................................................................................................................... 9 2.4 Processing of Unused Pins .............................................................................................................. 10 2.5 Notes on Using the RESET and INT Pins ........................................................................................ 10 3. WRITING AND VERIFYING ONE-TIME PROM (PROGRAM MEMORY) .............................. 11 3.1 Operating Mode When Writing/Verifying Program Memory .......................................................... 11 3.2 Program Memory Writing Procedure ............................................................................................... 12 3.3 Program Memory Reading Procedure ............................................................................................. 13 4. ELECTRICAL SPECIFICATIONS ................................................................................................ 14 5. PACKAGE DRAWING ................................................................................................................. 21 6. RECOMMENDED SOLDERING CONDITIONS .......................................................................... 22 APPENDIX. DEVELOPMENT TOOLS ............................................................................................... 23 Data Sheet U14542EJ1V0DS00 5 µPD17P228 1. DIFFERENCES AMONG µPD17225, 17226, 17227, 17228 AND µPD17P228 µPD17P228 is equipped with PROM to which data can be written by the user instead of the internal mask ROM (program memory) of the µPD17228. Table 1-1 shows the differences between the µPD17225, 17226, 17227, 17228 and µPD17P228. The differences among these five models are the program memory and mask option, and their CPU functions and internal hardware are identical. Therefore, the µPD17P228 can be used to evaluate the program developed for the µPD17225, 17226, 17227, and 17228 system. Note, however, that some of the electrical specifications such as supply current and low-voltage detection voltage of the µPD17P228 are different from those of the µPD17225, 17226, 17227, and 17228. Table 1-1. Differences among µPD17225, 17226, 17227, 17228 and µPD17P228 Product Name µPD17P228 µPD17225 µPD17226 µPD17227 µPD17228 Item Program memory One-time PROM Pull-up resistor of RESET Pin Low-voltage detector circuit 16 K bytes 4 K bytes 8 K bytes 12 K bytes 16 K bytes (8192 × 16) (2048 × 16) (4096 × 16) (6144 × 16) (8192 × 16) (0000H-1FFFH) (0000H-07FFH) (0000H-0FFFH) (0000H-17FFH) (0000H-1FFFH) 223 × 4 bits Data memory Note VPP pin, operation mode select pin Instruction execution time (tCY) Mask ROM 111 × 4 bits 223 × 4 bits Provided Any (mask option) Provided Any (mask option) Provided Not provided 2 µs 2 µs (VDD = 2.2 to 3.6 V) (VDD = 3.0 to 3.6 V) 4 µs (VDD = 2.0 to 3.6 V) 4 µs (VDD = 2.2 to 3.6 V) 16 µs (VDD = 2.2 to 3.6 V) Operation when P0C, P0D are standby Supply voltage Package Note 6 Retain output level immediately before standby mode VDD = 2.0 to 3.6 V VDD = 2.0 to 3.6 V 30-pin plastic SSOP • 28-pin plastic SOP (9.53 mm (375)) • 28-pin plastic SDIP (10.16 mm (400)) (7.62 mm (300)) • 30-pin plastic SSOP (7.62 mm (300)) Although the circuit configuration is identical, its electrical characteristics differ depending on the product. Data Sheet U14542EJ1V0DS00 µPD17P228 2. PIN FUNCTIONS 2.1 Normal Operation Mode Pin No. Symbol 16 17 18 19 P0A0 P0A1 P0A2 P0A3 20 21 22 23 Function Output Format At Reset 4-bit CMOS input port with pull-up resistor. Can be used for key return input of key matrix. When at least one of these pins goes low, standby function is released. – Input P0B0 P0B1 P0B2 P0B3 4-bit CMOS input port with pull-up resistor. Can be used for key return input of key matrix. When at least one of these pins goes low, standby function is released. – Input 24 25 26 27 P0C0 P0C1 P0C2 P0C3 4-bit N-ch open-drain output port. Can be used for key source output of key matrix. N-ch open-drain Low-level output 28 29 1 2 P0D0 P0D1 P0D2 P0D3 4-bit N-ch open-drain output port. Can be used for key source output of key matrix. N-ch open-drain Low-level output 4 5 6 7 P0E0 P0E1 P0E2 P0E3 4-bit input/output port. Can be set in input or output mode in 1-bit units. In output mode, this port functions as a high current CMOS output port. In input mode, function as CMOS input and can be specified to connect pull-up resistor by program. CMOS push-pull Input 8 REM Outputs transfer signal for infrared remote controller. Active-high output. CMOS push-pull Low-level output 13 RESET System reset input. CPU can be reset when low-level signal is input to this pin. While low-level signal is input, oscillator is stopped. This pin connected to pull-up resistor by mask option. – Input 9 VDD Power supply – – 12 GND Ground – – 3 INT External interrupt request signal input – Input N-ch open-drain Highimpedance Low-level output at low voltage detection Output detecting hang-up and drop in supply voltage. This pin outputs at low level either when an overflow occurs in the watchdog timer, when an overflow/underflow occurs in the stack, or when the supply voltage drops below a specified level. Connect this pin to the RESET pin. 14 WDOUT 11 10 XIN XOUT Connects ceramic resonator for system clock oscillation – (Oscillation stops) 15 30 IC1 IC2 These pins cannot be used. Leave open. – – Data Sheet U14542EJ1V0DS00 7 µPD17P228 2.2 PROM Programming Mode Pin No. Symbol 3 VPP Function Output Format At Reset Power supply for PROM programming. Apply +12.5 V to this pin as the program voltage when writing/ verifying program memory. – – 9 VDD Power supply. Apply +6 V to this pin when writing/verifying program memory. – – 11 CLK Inputs clock for PROM programming. – – 12 GND Ground. – – 20 MD0 23 MD3 Input pins used to select operation mode when PROM is programmed. – Input 24 27 28 29 1 2 D4 D7 D0 D1 D2 D3 CMOS push-pull Input Remark Input/output 8-bit data for PROM programming The other pins are not used in the PROM programming mode. How to handle the other opins are described in the section PIN CONFIGURATION (2) PROM programming mode. 8 Data Sheet U14542EJ1V0DS00 µPD17P228 2.3 Input/Output Circuits The equivalent input/output circuit for each µPD17P228 pin is shown below. (1) P0A, P0B (4) RESET V DD VDD (Mask option) Input buffer Input buffer (2) P0C, P0D Schmitt trigger input with hysteresis characteristics data Output latch N-ch (5) INT (3) P0E V DD data Pull-up register P-ch Input buffer Schmitt trigger input with hysteresis characteristics V DD data Output latch P-ch (6) REM N-ch output disable V DD data P-ch Selector Input buffer N-ch output disable (7) WDOUT data Data Sheet U14542EJ1V0DS00 N-ch 9 µPD17P228 2.4 Processing of Unused Pins Process the unused pins as follows: Table 2-1. Processing of Unused Pins Pin Recommended Connection P0A0-P0A3 Connect to VDD. P0B0-P0B3 Connect to VDD. P0C0-P0C3 Connect to GND. P0D0-P0D3 Connect to GND. P0E0-P0E3 Input : Individually connect to VDD or GND via resistor. Output : Leave open. REM Leave open. INT Connect to GND. WDOUT Connect to VDD via resistor. IC1, IC2 These pins cannot be used. Leave open. 2.5 Notes on Using the RESET and INT Pins In addition to the functions shown in 2. PIN FUNCTION, the RESET pin also has the function of setting a test mode (for IC testing) in which the internal operations of the µPD17P228 are tested. When a voltage higher than VDD is applied to either of these pins, the test mode is set. This means that, even during normal operation, the µPD17P228 may be set in the test mode if noise exceeding VDD is applied. For example, if the wiring length of the RESET or INT pin is too long, noise superimposed on the wiring line of the pin may cause the above problem. Therefore, keep the wiring length of these pins as short as possible to suppress the noise; otherwise, take noise preventive measures as shown below by using external components. • Connect capacitor between VDD • Connect diode with low VF between VDD and RESET/INT pin and RESET/INT pin VDD Diode with low VF VDD VDD RESET, INT VDD RESET, INT Connect the WDOUT and RESET pins since a low level is output after the test mode is set using the INT pin. 10 Data Sheet U14542EJ1V0DS00 µPD17P228 3. WRITING AND VERIFYING ONE-TIME PROM (PROGRAM MEMORY) The program memory of the µPD17P228 is a one-time PROM of 8192 × 16 bits. To write or verify this one-time PROM, the pins shown in Table 3-1 are used. Note that no address input pin is used. Instead, the address is updated by using the clock input from the CLK pin. Table 3-1. Pins Used to Write/Verify Program Memory Pin Name Function VPP Supplies voltage when writing/verifying program memory. Apply +12.5 V to this pin. VDD Power supply. Supply +6 V to this pin when writing/verifying program memory. CLK Inputs clock to update address when writing/verifying program memory. By inputting pulse four times to CLK pin, address of program memory is updated. MD0-MD3 Input to select operation mode when writing/verifying program memory. D0-D 7 Inputs/outputs 8-bit data when writing/verifying program memory. 3.1 Operating Mode When Writing/Verifying Program Memory The µPD17P228 is set in the program memory write/verify mode when +6 V is applied to the VDD pin and +12.5 V is applied to the VPP pin after the µPD17P228 has been in the reset status (VDD = 5 V, RESET = 0 V) for a specific time. In this mode, the operating modes shown in Table 3-2 can be set by setting the MD0 through MD3 pins. Leave all the pins other than those shown in Table 3-1 unconnected or connect them to GND via pull-down resistor (470 Ω). (Refer to PIN CONNECTION (2) PROM programming mode.) Table 3-2. Setting Operation Mode Setting of Operating Mode VPP +12.5 V VDD +6 V MD0 Operating Mode MD1 MD2 MD3 H L H L Program memory address 0 clear mode L H H H Write mode L L H H Verify mode H × H H Program inhibit mode ×: don’t care (L or H) Data Sheet U14542EJ1V0DS00 11 µPD17P228 3.2 Program Memory Writing Procedure The program memory is written at high speed in the following procedure. (1) Pull down the pins not used to GND via resistor. Keep the CLK pin low. (2) Supply 5 V to the V DD pin. Keep the V PP pin low. (3) Supply 5 V to the V PP pin after waiting for 10 µ s. (4) Set the program memory address 0 clear mode by using the mode setting pins. (5) Supply +6 V to V DD and +12.5 V to V PP. (6) Set the program inhibit mode. (7) Write data to the program memory in the 1-ms write mode. (8) Set the program inhibit mode. (9) Set the verify mode. If the data have been written to the program memory, proceed to (10). If not, repeat steps (7) through (9). (10) Additional writing of (number of times of writing in (7) through (9): X) × 1 ms. (11) Set the program inhibit mode. (12) Input a pulse to the CLK pin four times to update the program memory address (+1). (13) Repeat steps (7) through (12) up to the last address. (14) Set the 0 clear mode of the program memory address. (15) Change the voltages on the V DD and V PP pins to 5 V. (16) Turn off power. The following figure illustrates steps (2) through (12) above. Repeated X time Reset Verify Write Additional write Address increment VPP VPP VDD GND VDD VDD+1 VDD GND CLK D0-D7 Hi-Z Data input Hi-Z Data output Hi-Z MD0 MD1 MD2 MD3 12 Data Sheet U14542EJ1V0DS00 Data input Hi-Z µPD17P228 3.3 Program Memory Reading Procedure (1) Pull down the pins not used to GND via resistor. Keep the CLK pin low. (2) Supply 5 V to the V DD pin. Keep the V PP pin low. (3) Supply 5 V to the V PP pin after waiting for 10 µ s. (4) Set the program memory address 0 clear mode by using the mode setting pins. (5) Supply +6 V to V DD and +12.5 V to V PP. (6) Set the program inhibit mode. (7) Set the verify mode. Data of each address is output sequentially each time the clock pulse is input to (8) Set the program inhibit mode. (9) Set the program memory address 0 clear mode. the CLK pin four times. (10) Change the voltage on the V DD and V PP pins to 5 V. (11) Turn off power. The following figure illustrates steps (2) through (9) above. Reset VPP VPP VDD GND VDD VDD+1 VDD GND CLK D0-D7 Hi-Z Data output Data output Hi-Z MD0 MD1 "L" MD2 MD3 Data Sheet U14542EJ1V0DS00 13 µPD17P228 4. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (TA = 25°C) Item Symbol Conditions Ratings Unit Supply voltage VDD –0.3 to +7.0 V PROM power supply VPP –0.3 to +13.5 V VI –0.3 to VDD + 0.3 V VO –0.3 to VDD + 0.3 V Peak value –36.0 mA rms value –24.0 mA Peak value –7.5 mA rms value –5.0 mA Peak value –22.5 mA rms value –15.0 mA Peak value 7.5 mA rms value 5.0 mA Total of P0C, P0D, Peak value 22.5 mA WDOUT pins rms value 15.0 mA Total of P0E pins Peak value 30.0 mA rms value 20.0 mA Input voltage Output voltage High-level output current Note IOH REM pin 1 pin (P0E pin) Total of P0E pins Low-level output current Note IOL 1 pin (P0C, P0D, P0E, REM or WDOUT pin) Operating temperature TA –40 to +85 °C Storage temperature Tstg –65 to +150 °C Power dissipation Pd 180 mW Note TA = 85°C Calculate rms value by this expression: [rms value] = [Peak value] × √ Duty Caution Even if one of the parameters exceeds its absolute maximum rating even momentarily, the quality of the product may be degraded. The absolute maximum rating therefore specifies the upper or lower limit of the value at which the product can be used without physical damages. Be sure not to exceed or fall below this value when using the product. 14 Data Sheet U14542EJ1V0DS00 µPD17P228 Recommended Operating Ranges (TA = –40 to +85°C, VDD = 2.2 to 3.6 V) Item Symbol Supply voltage Conditions VDD1 fX = 1 MHz High-speed mode (Instruction execution time: 16 µs) VDD2 fX = 4 MHz Ordinary mode (Instruction execution time: 4 µs) VDD3 fX = 8 MHz High-speed mode (Instruction execution time: 4 µs) High-speed mode (Instruction execution time: 2 µs) VDD4 Oscillation frequency Operating temperature Low-voltage detector circuit Note MIN. Note TYP. MAX. Unit 2.2 3.6 V 3.0 3.6 V fX 1.0 4.0 8.0 MHz TA –40 +25 +85 °C TCY 4 32 µs Reset if the status of VDD = 2.05 V (TYP.) lasts for 1 ms or longer. Program hang-up does not occur even if the voltage drops, until the reset function is effected (when the RESET pin and WDOUT pin are connected). Some oscillators stop oscillating before the reset function is effected. fX vs VDD (MHZ) 10 9 8 7 6 System clock: fX (MHZ) (Normal mode) 5 4 3 Operation guaranteed area 2 1 0.4 0 2 2.2 3 3.6 4 Supply voltage: VDD (V) Remark The region indicated by the broken line in the above figure is the guaranteed operating range in the highspeed mode. Data Sheet U14542EJ1V0DS00 15 µPD17P228 System Clock Oscillator Characteristics (TA = –40 to +85°C, VDD = 2.2 to 3.6 V) Recommended Constants Resonator Ceramic resonator X IN X OUT Item Conditions Oscillation frequency (fX)Note 1 Oscillation Note 2 stabilization time MIN. TYP. MAX. Unit 1.0 4.0 8.0 MHz 4 ms After VDD reached MIN. in oscillation voltage range Notes 1. The oscillation frequency only indicates the oscillator characteristics. 2. The oscillation stabilization time is necessary for oscillation to be stabilized, after VDD application or STOP mode release. Caution To use a system clock oscillator circuit, perform the wiring in the area enclosed by the dotted line in the above figure as follows, to avoid adverse wiring capacitance influences: • Keep wiring length as short as possible. • Do not cross a signal line with some other signal lines. Do not route the wiring in the vicinity of lines through which a large current flows. • Always keep the oscillator capacitor ground at the same potential as GND. Do not ground the capacitor to a ground pattern, through which a large current flows. • Do not extract signals from the oscillator. External circuit example XIN XOUT R1 C1 Remark C2 To select a resonator and determine oscillator constants, please evaluate the oscillation yourself or request the resonator manufacturer to evaluate it. 16 Data Sheet U14542EJ1V0DS00 µPD17P228 DC Characteristics (TA = –40 to +85°C, VDD = 2.2 to 3.6 V) Item High-level input voltage Symbol Conditions MIN. TYP. MAX. Unit VIH1 RESET, INT 0.8VDD VDD V VIH2 P0A, P0B 0.7VDD VDD V VIH3 P0E 0.8VDD VDD V VIL1 RESET, INT 0 0.2VDD V VIL2 P0A, P0B 0 0.3VDD V VIL3 P0E 0 0.35VDD V High-level input leakage current ILIH P0A, P0B, P0E, RESET, INT VIH = VDD 3 µA Low-level input leakage ILIL1 INT VIL = 0 V –3 µA current ILIL2 P0E VIL = 0 V w/o pull-up resistor –3 µA High-level output leakage current ILOH P0C, P0D, P0E, WDOUT VOH = VDD 3 µA Low-level output leakage ILOL P0E, WDOUT VOL = 0 V w/o pull-up resistor –3 µA R1 P0E, RESET 25 50 100 kΩ R2 P0A, P0B 100 200 400 kΩ High-level output current IOH1 REM VOH = 1.0 V, VDD = 3 V –6 –13 –24 mA High-level output voltage VOH P0E, REM IOH = –0.5 mA VDD–0.3 VDD V Low-level output voltage VOL1 P0C, P0D, REM, WDOUT IOL = 0.5 mA 0 0.3 V VOL2 P0E IOL = 1.5 mA 0 0.3 V VDT WDOUT = low level VDT = VDD 2.2 V 3.6 V Low-level input voltage current Internal pull-up resistor Low-voltage detector circuit Data retention voltage Supply current VDDDR IDD1 RESET = low level or STOP mode Operating mode VDD = 3 V ± 10% (high-speed) IDD2 Operating mode VDD = 3 V ± 10% (low-speed) IDD3 IDD4 2.05 HALT mode STOP mode VDD = 3 V ± 10% 1.3 fX = 1 MHz 0.55 1.1 mA fX = 4 MHz 1.0 2.0 mA fX = 8 MHz 1.3 2.6 mA fX = 1 MHz 0.5 1.0 mA fX = 4 MHz 0.75 1.5 mA fX = 8 MHz 0.9 1.8 mA fX = 1 MHz 0.4 0.8 mA fX = 4 MHz 0.5 1.0 mA fX = 8 MHz 0.6 1.2 mA 2.0 20.0 µA 2.0 5.0 µA VDD = 3 V ± 10% built-in POC Data Sheet U14542EJ1V0DS00 TA = 25 °C 17 µPD17P228 AC Characteristics (TA = –40 to +85°C, VDD = 2.2 to 3.6 V) Item Symbol Note CPU clock cycle time (instruction execution time) Conditions MIN. tCY1 tCY2 VDD = 3.0 to 3.6 V TYP. MAX. Unit 3.8 33 µs 1.9 33 µs INT high/low level width tINTH, tINTL 20 µs RESET low level lwidth tRSL 10 µs Note tCY vs VDD The CPU clock cycle time (instruction execution time) is determined by the oscillation frequency of the reso- 40 nator connected and SYSCK (RF: address 02H) of the 33 register file. The figure on the right shows the CPU clock cycle time CPU clock cycle time tcY (µs) tCY vs. supply voltage VDD characteristics. 10 9 8 7 6 Operation guaranteed area 5 4 3.8 3 2 1.9 2.2 1 0 1 2 3.6 3 4 Supply voltage VDD (V) 18 Data Sheet U14542EJ1V0DS00 µPD17P228 DC Programming Characteristics (TA = 25 °C, VDD = 6.0 ±0.25 V, VPP = 12.5 ±0.3 V) Parameter Symbol High-level input voltage Test Conditions MIN. MAX. Unit VDD V VDD–0.5 VDD V 0 0.3 VDD V 0 0.4 V 10 µA V IH1 Other than CLK 0.7 VDD V IH2 CLK V IL1 Other than CLK V IL2 CLK ILI V IN = VIL or V IH High-level output voltage V OH IOH = –1 mA Low-level output voltage VOL IOL = 1.6 mA V DD supply current IDD V PP supply current IPP Low-level input voltage Input leakage current TYP. VDD–1.0 V MD0 = VIL, MD1 = VIH 0.4 V 30 mA 30 mA Cautions 1. Keep V PP to within +13.5 V including overshoot. 2. Apply VDD before VPP and turns it off after VPP. AC Programming Characteristics (TA = 25 °C, VDD = 6.0 ±0.25 V, VPP = 12.5 ±0.3 V) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit tAS 2 µs MD1 setup time (vs. MD0↓) tM1S 2 µs Data setup time (vs. MD0↓) tDS 2 µs Address hold timeNote (vs. MD 0↑) tAH 2 µs Data hold time (vs. MD0↑) tDH 2 MD0↑→ data output float delay time tDF 0 VPP setup time (vs. MD3↑) tVPS 2 µs VDD setup time (vs. MD3↑) tVDS 2 µs Initial program pulse width tPW 0.95 Additional program pulse width tOPW 0.95 MD0 setup time (vs. MD1↑) tMOS MD0↓→ data output delay time tDV MD0 = MD1 = VIL MD1 hold time (vs. MD0↑) tM1H tM1H+tM1R ≥ 50 µs MD1 recovery time (vs. MD0↓) tM1R Address setup timeNote (vs. MD0↓) Program counter reset time CLK input high-, low-level width µs 130 1.0 ns 1.05 ms 21.0 ms µs 2 1 µs 2 µs 2 µs tPCR 10 µs tXH, tXL 0.125 µs CLK input frequency fX Initial mode set time tI 2 µs MD3 setup time (vs. MD1↑) tM3S 2 µs MD3 hold time (vs. MD1↓) tM3H 2 µs MD3 setup time (vs. MD0↓) tM3SR When program memory is read AddressNote → data output delay time tDAD When program memory is read Address Note → data output hold time 4.19 µs 2 2 tHAD When program memory is read 0 tM3HR When program memory is read 2 MD3↓→ data output float delay time tDFR When program memory is read Reset setup time tRES MD3 hold time (vs. MD0↑) 130 µs ns µs 2 10 MHz µs µs Notes The internal address increment (+1) is performed on the fall of the 3rd clock, where 4 clocks compreise one cycle. The internal clock is not connected to a pin. Data Sheet U14542EJ1V0DS00 19 µPD17P228 Program Memory Write Timing tRES tVPS VPP VPP VDD GND VDD VDD+1 VDD GND tVDS tXH CLK D0-D7 tXL Hi-Z Data input tI tDS Data output tDH tDV tDF Data input Data input tDH tAH tDS tAS MD0 tPW tM1R tMOS tOPW MD1 tPCR tM1S tM1H MD2 tM3H tM3S MD3 Program Memory Read Timing tRES tVPS VPP VPP VDD GND VDD tVDS VDD+1 VDD tXH GND CLK tXL tDAD tHAD Data output D0-D7 Data output tDV tI MD0 MD1 "L" tPCR MD2 tM3SR MD3 20 Data Sheet U14542EJ1V0DS00 tM3HR tDFR µPD17P228 5. PACKAGE DRAWING 30-PIN PLASTIC SSOP (7.62 mm (300)) 30 16 detail of lead end F G T P 1 L 15 U E A H I J S C D N M S B K M NOTE Each lead centerline is located within 0.13 mm of its true position (T.P.) at maximum material condition. ITEM A MILLIMETERS 9.85±0.15 B 0.45 MAX. C 0.65 (T.P.) D 0.24 +0.08 −0.07 E 0.1±0.05 F 1.3±0.1 G 1.2 H 8.1±0.2 I 6.1±0.2 J 1.0±0.2 K 0.17±0.03 L 0.5 M 0.13 N 0.10 P 3° +5° −3° T 0.25 U 0.6±0.15 S30MC-65-5A4-2 Data Sheet U14542EJ1V0DS00 21 µPD17P228 6. RECOMMENDED SOLDERING CONDITIONS For the µPD17P228 soldering must be performed under the following conditions. For details of recommended conditions for surface mounting, refer to information document "Semiconductor Device Mounting Technology Manual" (C10535E). For other soldering methods, please consult with NEC personnel. Table 6-1. Soldering Conditions of Surface Mount Type • µPD17P228MC-5A4: 30-pin plastic SSOP (7.62 mm(300)) Soldering Method Soldering Conditions Symbol Infrated Reflow Package peak temperature: 235°C, Time: 30 seconds max. (210°C min.), Number of times: 2 max. Number of days: 3 (after that, prebaking is necessary at 125°C for 10 hours) IR35-103-2 VPS Package peak temperature: 215°C, Time: 40 seconds max. (200°C min.), Number of times: 2 max. Number of days: 3 (after that, prebaking is necessary at 125°C for 10 hours) VP15-103-2 Wave soldering Solder bath temperature: 260°C max, Time: 10 seconds max., Number of times: once, preheating temperature: 120°C max. (package surface temperature) Number of days: 3 (after that, prebaking is necessary at 125°C for 10 hours) WS-60-103-1 Partial heating Pin temperature: 300°C max., Time: 3 seconds max. (per side of device) Note — Number of days in storage after the dry pack has been opened. The storage conditions are at 25°C, 65% RH MAX. Caution Do not use two or more soldering methods in combination (except the partial heating method). 22 Data Sheet U14542EJ1V0DS00 µPD17P228 APPENDIX. DEVELOPMENT TOOLS To develop the programs for the µPD17P228 subseries, the following development tools are available: Hardware Name In-circuit emulator IE-17K, IE-17K-ETNote 1 Remarks IE-17K and IE-17K-ET are the in-circuit emulators used in common with the 17K series microcontroller. TM IE-17K and IE-17K-ET are connected to a PC-9800 series or IBM PC/AT compatible machines as the host machine with RS-232C. By using these in-circuit emulators with a system evaluation board corresponding to the microcomputer, the emulators can emulate the microcomputer. A higher level debugging TM environment can be provided by using man-machine interface SIMPLEHOST . SE board (SE-17225) This is an SE board for µPD17225 subseries. It can be used alone to evaluate a system or in combination with an in-circuit emulator for debugging. Emulation probe (EP-17K30GS) EP-17K30GS is an emulation probe for 17K series 30-pin SSOP (MC-5A4). When used with EV-9500GT-30Note 2, it connects an SE board to the target system. Conversion adapter Note 2 (EV-9500GT-30 ) The EV-9500GT-30 is a conversion adapter for the 30-pin SSOP (MC-5A4). It is used to connect the EP-17K30GS and target system. PROM programmer Note 3 Note 3 (AF-9706 , AF-9708 , Note 3 AF-9709 ) AF-9706, AF-9708, and AF-9709 are PROM programmers corresponding to µPD17P228. By connecting program adapter PA-17P236 to this PROM programmer, µPD17P228 can be programmed. Program adapter (PA-17P236) PA-17P236 are adapters that is used to program µPD17P228, and is used in combination with AF-9706, AF-9708, or AF-9709. Notes 1. Low-cost model: External power supply type 2. Two EV-9500GT-30 are supplied with the EP-17K30GS. Five EV-9500GT-30s are optionally available as a set. 3. These are products from Ando Electric Co., Ltd. For details, consult Ando Electric Co., Ltd. (Tel: 033733-1166). Data Sheet U14542EJ1V0DS00 23 µPD17P228 Software Name 17K assembler (RA17K) Device file (AS17225) Support software (SIMPLEHOST) 24 Outline Host Machine OS WindowsTM Supply Order Code 3.5" 2HD µSAA13RA17K 3.5" 2HC µSAB13RA17K The RA17K is an assembler common to the 17K series products. When developing the program of devices, RA17K is used in combination with a device file (AS17225). PC-9800 series Japanese IBM PC/AT compatible machine Japanese Windows The AS17225 is a device file for µPD17225, 17226, 17227, and 17228 and is used in combination with an assembler for the 17K series (RA17K). PC-9800 series Japanese Windows 3.5" 2HD µSAA13AS17225 IBM PC/AT compatible machine Japanese Windows 3.5" 2HC µSAB13AS17225 English Windows SIMPLEHOST is a software package that enables man-machine interface on the Windows when a program is developed by using an incircuit emulator and a personal computer. PC-9800 Japanese Windows 3.5" 2HD µSAA13ID17K Japanese Windows 3.5" 2HC µSAB13ID17K µSBB13RA17K English Windows µSBB13AS17225 series IBM PC/AT compatible machine English Windows Data Sheet U14542EJ1V0DS00 µSBB13ID17K µPD17P228 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to V DD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. Data Sheet U14542EJ1V0DS00 25 µPD17P228 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: • Device availability • Ordering information • Product release schedule • Availability of related technical literature • Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) • Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) NEC Electronics (Germany) GmbH NEC Electronics Hong Kong Ltd. Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580 Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics Hong Kong Ltd. Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics (France) S.A. NEC Electronics Singapore Pte. Ltd. Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290 Spain Office Madrid, Spain Tel: 91-504-2787 Fax: 91-504-2860 United Square, Singapore 1130 Tel: 65-253-8311 Fax: 65-250-3583 NEC Electronics Italiana s.r.l. NEC Electronics (Germany) GmbH Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388 NEC Electronics (France) S.A. NEC Electronics (Germany) GmbH Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490 NEC Electronics (UK) Ltd. NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 Fax: 02-2719-5951 NEC do Brasil S.A. Electron Devices Division Rodovia Presidente Dutra, Km 214 07210-902-Guarulhos-SP Brasil Tel: 55-11-6465-6810 Fax: 55-11-6465-6829 J99.1 26 Data Sheet U14542EJ1V0DS00 µPD17P228 [MEMO] Data Sheet U14542EJ1V0DS00 27 µPD17P228 SIMPLEHOST is a trademark of NEC Corporation. Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of IBM Corporation. The export of this product from Japan is regulated by the Japanese government. To export this product may be prohibited without governmental license, the need for which must be judged by the customer. The export or re-export of this product from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative. • The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. • NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. • Descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. • While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. • NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated “quality assurance program“ for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. M7 98.8