N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole TECHNICAL DATA SHEET PE4297 N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole Configuration Connector Connector Specification Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style Mount Method N Female MIL-C-39012 RG59,RG62 Clamp/Solder Straight Bulkhead Electrical Specifications Impedance, Ohms 50 Mechanical Specifications Temperature Operating Range, deg C -65 to +165 Size Length, in [mm] Width/Dia., in [mm] 1.67 [42.42] 0.817 [20.75] Weight, lbs [g] 0.11 [49.9] Connector Type Contact Material and Plating Contact Plating Specification Body Material and Plating Dielectric Type N Female Gold MIL-G-45204 Brass, Nickel Teflon . Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole PE4297 PE4297 REV 1 N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole TECHNICAL DATA SHEET PE4297 Plotted and Other Data Notes: Values at 25 °C, sea level N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole PE4297 URL: http://www.pasternack.com/n-female-standard-rg59-rg62-connector-pe4297-p.aspx PE4297 REV 2 © 2013 Pasternack Enterprises All Rights Reserved PE4297 REV RG62 USES PTFE INSERT. INSERT PTFE BEFORE CONTACT. TAPER END FIRST. NOTE 2. FORM BRAID OVER CLAMP NUT (4). TRIM BRAID BACK TO SHOULDER. CUT DIELECTRIC & CENTER CONDUCTOR TO DIMENSION SHOWN. DO NOT NICK CENTER CONDUCTOR. SOLDER CONTACT TO CENTER CONDUCTOR. REMOVE EXCESS SOLDER. DO NOT OVER HEAT DIELECTRIC. INSERT CABLE ASSEMBLY INTO BODY & TIGHTEN. 1. SLIDE CLAMP NUT (1), WASHER (2) & GASKET (3) OVER CABLE. STRIP CABLE AS SHOWN. DO NOT NICK BRAID WHILE CUTTING JACKET. TAPER END OF BRAID TO PERMIT ASSEMBLY OF BRAID CLAMP (4). SLIDE BRAID CLAMP (4) OVER BRAID & SEAT AGAINST CABLE. ASSEMBLY PROCEDURES FSCM NO. 53919 PE4297 DWG TITLE CAD FILE 032813-A SCALE N/A SIZE A 2233 NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. N Female Bulkhead Connector Clamp/Solder Attachment For RG59, RG62, .640 inch DD Hole PE4297 CAD Drawing 3