SMA3103 Ordering number : ENA1580A SANYO Semiconductors DATA SHEET SMA3103 Silicon MMIC Wideband Amplifier Features • • • • • High Gain Wideband response Low current High output power Port impedance : Gp=26.5dB typ. @1GHz : fu=3.3GHz : ICC=19mA typ : Po(1dB)=5dBm : input/output 50Ω Specifications Absolute Maximum Ratings at Ta=25°C Parameter Symbol Supply Voltage Conditions Ratings Unit VCC ICC 6 V 40 mA PD Topr 280 mW Operating Temperature --40 to +85 °C Storage Temperature Tstg --55 to +150 °C Circuit Current Allowable Power Dissipation Package Dimensions Product & Package Information unit : mm (typ) 7022A-018 • Package : MCPH6 • JEITA, JEDEC : SC-88, SC-70-6, SOT-363 • Minimum Packing Quantity : 3,000 pcs./reel 6 5 0 to 0.02 1 2 Marking TL 3 0.65 LC LOT No. 0.3 0.85 0.25 Packing Type : TL 4 LOT No. 0.07 SMA3103-TL-E 0.15 2.1 1.6 0.25 2.0 1 2 3 1 : VCC 2 : GND 3 : OUT 4 : GND 5 : GND 6 : IN 6 5 4 SANYO : MCPH6 http://semicon.sanyo.com/en/network 72512 TKIM/N1109AM TKIM TC-00002164 No. A1580-1/8 SMA3103 Recommended Operating Condition at Ta=25°C Parameter Supply Voltage Operating Ambient Temperature Symbol Conditions VCC Topr Ratings min typ Unit max 4.5 5 5.5 V --40 +25 +85 °C Note) Pay attention to handling since it is liable to be affected by static electricity due to the high frequency process adopted. Electrical Characteristics at Ta=25°C, VCC=5V, Zs=ZL=50Ω Parameter Circuit Current Symbol Conditions ICC Power Gain Gp Isolation ISL Input Return Loss RLin Output Return Loss RLout Noise Figure NF Gain 1dB Compression Output Power Po(1dB) Upper Limit Operating Frequency fu Ratings min typ Unit max 14.0 19.0 25.0 f=1GHz 24.0 26.5 29.0 f=2.2GHz 24.0 27.0 30.0 f=1GHz 31.0 33.0 f=2.2GHz 31.0 33.0 f=1GHz 12.0 20.0 f=2.2GHz 10.0 14.0 f=1GHz 12.0 20.0 f=2.2GHz 10.0 16.0 dB dB 4.7 5.3 f=2.2GHz 4.7 5.3 6.0 8.2 f=2.2GHz 4.0 5.7 3dB down below flat gain at f =1GHz 3.3 dB dB f=1GHz f=1GHz mA dB dBm GHz Ordering Information Device SMA3103-TL-E Package Shipping memo MCPH6 3,000pcs./reel Pb Free No. A1580-2/8 SMA3103 Test Circuit 100pF IN 6 5 4 1 2 3 100pF OUT 1000pF 100nH VCC Connect 2, 4 and 5 with GND. Design of the Evaluation Board IN OUT C1 L1 C2 C3 Symbol C1, C2 VCC Value C3 100pF 1000pF L1 100nH No. A1580-3/8 SMA3103 ICC -- VCC Circuit Current, ICC -- mA 25 20 15 10 5 0 0 1 2 3 4 5 Circuit Voltage, VCC -- V 6 IT15097 Gp -- f 30 RLin -- f 0 5.5V Input Return Loss, RLin -- dB --5 Power Gain , Gp -- dB 5.0V 4.5V 25 20 15 0 1000 2000 3000 Frequency, f -- MHz 5.0V 5.5V --40 --50 0 1000 2000 3000 Pout -- Pin --10 --30 --20 Input Power, Pin -- dBm --10 0 IT15102 3000 4000 IT15099 RLout -- f --10 5.0V 5.5V --15 4.5V --20 --25 --30 0 1000 2000 3000 4000 IT15101 Pout -- Pin 20 Output Power, Pout -- dBm Output Power, Pout -- dBm 0 --40 2000 Frequency, f -- MHz VCC=5.0V f=1.0GHz --50 1000 IT15100 10 --20 --60 0 --5 --35 4000 Frequency, f -- MHz 20 --30 Frequency, f -- MHz Output Return Loss, RLout -- dB Isolation, ISL -- dB --20 4.5V --25 0 --10 --30 V 4.5 --20 IT15098 ISL -- f 0 V 5.0 --15 --35 4000 V 5.5 --10 VCC=5.0V f=2.2GHz 10 0 --10 --20 --60 --50 --40 --30 --20 Input Power, Pin -- dBm --10 0 IT15103 No. A1580-4/8 SMA3103 S Parameter S11 S22 50 50 100 25 250 10 100 25 250 10 3GHz 25 10 0 2GHz 50 100 250 10 0 25 50 1GHz 100 250 3GHz 1GHz 2GHz --10 --250 --25 --10 --250 --25 --100 --50 IT15104 --100 --50 IT15105 No. A1580-5/8 SMA3103 Embossed Taping Specification SMA3103-TL-E No. A1580-6/8 SMA3103 Outline Drawing SMA3103-TL-E Land Pattern Example Mass (g) Unit 0.008 mm * For reference Unit: mm 2.1 0.6 0.4 0.65 0.65 No. A1580-7/8 SMA3103 Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2012. Specifications and information herein are subject to change without notice. PS No. A1580-8/8