Ordering number : ENA2140 STK672-120-SL-E Thick-Film Hybrid IC 2-phase Stepping Motor Driver Overview The STK672-120-SL-E is a hybrid IC for use as a unipolar, 2-phase stepping motor driver with PWM current control. Applications • Office photocopiers, printers, etc. Features • The motor speed can be controlled by the frequency of an external clock signal (the CLOCK pin signal). • The excitation type is switched according to the state (low or high) of the MODE pin. The mode is set to 2-phase or 1-2phase excitation on the rising edge of the clock signal. • A motor direction switching pin (the CWB pin) is provided. • All inputs are schmitt inputs and 40kΩ (typical: –50 to +100%) pull-up resistors are built in. • The motor current can be set by changing the Vref pin voltage. Since a 0.165Ω current detection resistor is built in, a current of 1A is set for each 0.165V of applied voltage. • The input frequency range for the clock signal used for motor speed control is 0 to 25kHz. • Supply voltage ranges: VCC = 10 to 42V, VDD = 5.0V ±5% • This IC supports motor operating currents of up to 2.4A at Tc = 105°C, and of up to 4.0A at Tc = 25°C. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment. The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for new introduction or other application different from current conditions on the usage of automotive device, communication device, office equipment, industrial equipment etc. , please consult with us about usage condition (temperature, operation time etc.) prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' s products or equipment. O1712HKPC 5-6407 No. A2140-1/11 STK672-120-SL-E Specifications Absolute Maximum Ratings at Tc = 25°C Parameter Symbol Conditions Ratings unit Maximum supply voltage 1 VCC max No signal 52 V Maximum supply voltage 2 VDD max No signal -0.3 to +7.0 V Input voltage VIN max Logic input pins -0.3 to +7.0 V Output current IOH max 10μA 1 pulse (resistance load) 4 A Repeated avalanche capacity Ear max 36 mJ Allowable power dissipation Pd max 8.5 W Operating substrate temperature Tc max 105 °C Junction temperature Tj max 150 °C Storage temperature Tstg -40 to +125 °C With an arbitrarily large heat sink. Per MOSFET Allowable Operating Ranges at Ta=25°C Parameter Symbol Conditions Operating supply voltage 1 VCC With signals applied Operating supply voltage 2 VDD With signals applied Input high voltage VIH Pin 8, 9, 10, 11 and 12 Output current 1 IOH1 Tc=105°C, CLOCK≥200Hz Output current 2 IOH2 Tc=80°C, CLOCK≥200Hz, Ratings See the motor current (IOH) derating curve unit 10 to 42 V 5±5% V 0 to VDD V 2.4 A 3.0 A CLOCK frequency fCL Minimum pulse width: 20μs 0 to 25 kHz Phase driver withstand voltage VDSS ID=1mA (Tc=25°C) 100min V Electrical Characteristics at Tc=25°C, VCC=24V, VDD=5.0V Parameter Symbol Conditions VDD supply current ICCO CLOCK=GND Output average current Ioave With R/L = 3Ω/3.8mH in each phase Vref = 0.176V min typ 0.56 max unit 2.6 6 0.62 0.69 mA A FET diode forward voltage Vdf If=1A (RL=23Ω) 1.1 1.7 V Output saturation voltage Vsat RL=23Ω 0.4 0.56 V High-level input voltage VIH Pins 6 to 9 (4 pins) Low-level input voltage VIL Pins 6 to 9 (4 pins) Input current IIL With pins 6 to 9 at the ground level. Pull-up resistance: 40kΩ (typical) Vref input voltage VrH Pin 12 Vref input bias current IIB With pin 12 at 1V 4.0 62 V 1.0 V 125 250 μA 3.5 V 50 500 nA 0 Notes: A fixed-voltage power supply must be used. No. A2140-2/11 STK672-120-SL-E Package Dimensions unit:mm (typ) 46.6 8.5 1 12 2.0 (9.6) 18.9 12.7 3.6 25.5 41.2 0.4 0.5 5.2 7.4 11 2=22 Figure 1 Derating Curve of Motor Current, IOH, vs. STK672-120-SL-E Operating Substrate Temperature, Tc IOH -- Tc 4.5 Motor current, IOH -- A VCC=24V Motor: R=0.4Ω L=1.2mH Operating region when fCL≥200Hz 4.0 3.5 3.0 Operating region in hold mode 2.5 2.4 2.0 2.0 1.5 1.0 0.5 0 0 20 40 60 80 100 105 120 Operating substrate temperature, Tc -- °C Notes • The current range given above represents conditions when output voltage is not in the avalanche state. • Tc must measure surface metal temperature on rear side center of this device. No. A2140-3/11 STK672-120-SL-E Block Diagram A AB 5 B 4 3 BB 2 VDD 10 F1 MODE 8 CLOCK 9 F2 F3 F4 Excitation mode selection Phase excitation signal generation Phase advance counter CWB 7 + VrefA - RESETB 6 Chopping circuit R1 C1 R2 RsA + VrefB - Off time setting RsB 1 GND C2 Vref 12 SUB SP 11 Sample Application Circuit STK672-120-SL-E 10μF VDD=5V CO3 CLOCK + 10 9 MODE 8 CWB 7 RESETB 5V Two-phase stepping motor 5 4 3 6 5V RO3 D1 2 AB BB + CO2 At least 100μF 0.1μF + RO2 VCC 24V B RO1 Vref CO4 10μF A 12 1 GND P.GND 11 CO1 No. A2140-4/11 STK672-120-SL-E Precautions • To minimize noise in the 5V system, locate the ground side of capacitor CO2 in the above circuit as close as possibleto pin 1 of the IC. • Insert resistor RO3 (47 to 100Ω) so that the discharge energy from capacitor CO4 is not directly applied to the CMOS-IC in this hybrid device. If the diode D1 has Vf characteristics with Vf less than or equal to 0.6V (when If = 0.1A), this will be smaller than the CMOS IC input pin diode Vf. If this is the case RO3 may be replaced with a short without problem. • Standard or HC type input levels are used for the pin 7, 8, and 9 inputs. • If open-collector type circuits are used for the pin 7, 8, and 9 inputs, these circuit will be in the high-impedance state for high level inputs. As a result, chopping circuit noise may cause the input circuits to operate incorrectly. To prevent incorrect operation due to such noise, capacitors with values between 470 and 1000pF must be connected between pins 7 and 11, 8 and 11, and 9 and 11. (A capacitor with a value between 470 and 1000pF must be connected between pins 6 and 11 as well if an open-collector output IC is used for the RESETB pin (pin 6) input.) • Taking the input bias current (IIB) characteristics into account, the resistor RO1 must not exceed 100kΩ. • The following circuit (for a lowered current of over 0.2A) is recommended if the application needs to temporarily lower the motor current. Here, a value of close to 100kΩ must be used for resistor RO1 to make the transistor output saturation voltage as low as possible. 5V 5V RO1 RO1 Vref R3 Vref RO2 R3 RO2 Input Pin Functions (CMOS input levels) Pin Pin No. Function Input conditions when operating CLOCK 9 Reference clock for motor phase current switching Operates on the rising edge of the signal MODE 8 Excitation mode selection Low: 2-phase excitation CWB 7 Motor direction switching Low: CW (forward) RESETB 6 System reset and A, AB, B, and BB outputs cutoff. High: 1-2 phase excitation High: CCW (reverse) A reset is applied by a low level Applications must apply a reset signal for at least 20μs when power is first applied. (1) A simple reset function is formed from D1, CO4, and RO3 in this application circuit. With the CLOCK input held low, when the 5V supply voltage is brought up a reset is applied if the motor output phases A and BB are driven. If the 5V supply voltage rise time is slow (over 50ms), the motor output phases A and BB may not be driven. Increase the value of the capacitor CO4 and check circuit operation again. (2) See the timing chart for the concrete details on circuit operation. No. A2140-5/11 STK672-120-SL-E Usage Notes • 5V system input pins [RESETB and CLOCK 〈〈Input signal timing when power is first applied〉〉] As shown in the timing chart, a RESETB signal input is required by the driver to operate with the timing in which the F1 gate is turned on first. The RESETB signal timing must be set up to have a width of at least 20μs, as shown below. The capacitor CO4 and the resistor RO3 in the application circuit form simple reset circuit that uses the RC time constant rising time. However, when designing the RESETB input based on CMOS levels, the application must have the timing shown in figure 2. Rise of the 5V supply voltage RESETB signal input At least 20μs CLOCK signal At least 10μs Figure 2 RESETB and CLOCK Signals Input Timing See the timing chart for details on the CLOCK, MODE, CWB, and other input pins. [Vref 〈〈Motor current peak value setting〉〉] In the sample application circuit, the peak value of the motor current (IOH) is set by RO1, RO2, and VDD (5V) as described by the formula below. IOH 0 Figure 3 Motor Current IO Flowing into the Driver IC IOH = Vref÷Rs Here, Rs is hybrid IC internal current detection resistor Vref = (RO2÷ (RO1+RO2)) ×5V STK672-120-SL-E: Rs = 0.165Ω • Allowable motor current operating range The motor current (IOH) must be held within the range corresponding to the area under the curve shown in figure 1. For example, if the operating substrate temperature Tc is 105°C, then IOH must be held under IOH = 2.4A, and in hold mode IOH must be held under IOH = 2.0A. No. A2140-6/11 STK672-120-SL-E • Thermal design [Operating range in which a heat sink is not used] The STK672-120-SL-E- package has a structure that uses no screws, and is recommended for use without a heat sink .This section discusses the safe operating range when no heat sink is used. In the maximum ratings specifications, Tc max is specified to be 105°C, and when mounted in an actual end product system, the Tc max value must never be exceeded during operation. Tc can be expressed by formula (A) below, and thus the range for ΔTc must be stipulated so that Tc is always under 105°C. Tc = Ta + ΔTc (A) Ta: Hybrid IC ambient temperature, ΔTc: Temperature increase across the aluminum substrate As shown in figure 6, the value of ΔTc increases as the hybrid IC internal average power dissipation PD increases. As shown in figure 5, PD increases with the motor current. Here we describe the actual PD calculation using the example shown in the motor current timing chart in figure 4. Since there are periods when current flows and periods when the current is off during actual motor operation, PD cannot be determined from the data presented in figure 5. Therefore, we calculate PD assuming that actual motor operation consists of repetitions of the operation shown in figure 4. IO1 Motor phase current (sink side) IO2 -IO1 T1 T2 T3 T0 Figure 4 Motor Current Timing T1: Motor rotation operation time T2: Motor hold operation time T3: Motor current off time T2 may be reduced, depending on the application. T0: Single repeated motor operating cycle IO1 and IO2: Motor current peak values Due to the structure of motor windings, the phase current is a positive and negative current with a pulse form. Note that figure 4 presents the concepts here, and that the on/off duty of the actual signals will differ. The hybrid IC internal average power dissipation PD can be calculated from the following formula. PD = (T1 × P1 + T2 × P2 + T3 × 0) ÷ T0 ------------------------------------------- (I) (Here, P1 is the PD for IO1 and P2 is the PD for IO2) If the value calculated in formula (I) above is under 1.4W, then from figure 6 we see that operation is allowed up to an ambient temperature Ta of 60°C. While the operating range when a heat sink is not used can be determined from formula (I) above, figure 5 is merely asingle example of one operating mode for a single motor. For example, while figure 5 shows a 2-phase excitation motor, if 1-2 phase excitation is used with a 500Hz clock frequency, the drive will be turned off for 25% of the time and the dissipation PD will be reduced to 75% of that in figure 5. It is extremely difficult for SANYO to calculate the internal average power dissipation PD for all possible end product conditions. After performing the above rough calculations, always install the hybrid IC in an actual end product and verify that the substrate temperature Tc does not rise above 105°C. No. A2140-7/11 STK672-120-SL-E Timing Charts 2-phase excitation MODE RESETB CWB CLOCK Gate F1 Gate F2 Gate F3 Gate F4 100% VrefA 100% VrefB 1-2 phase excitation MODE RESETB CWB CLOCK Gate F1 Gate F2 Gate F3 Gate F4 100% VrefA 100% VrefB No. A2140-8/11 STK672-120-SL-E 1-2 phase excitation MODE RESETB CWB CLOCK Gate F1 Gate F2 Gate F3 Gate F4 100% VrefA 100% VrefB 2-phase excitation→Switch to 1-2 phase excitation MODE RESETB CWB CLOCK Gate F1 Gate F2 Gate F3 Gate F4 100% VrefA 100% VrefB No. A2140-9/11 STK672-120-SL-E Hybrid IC internal average power dissipation, PD -- W Figure 5 Hybrid IC internal average power dissipation, PD - Motor current, IOH PD -- IOH 18 VCC=24V, VDD=5.0V Clock=500Hz Continuous 2-phase excitation operation Motor used: R=0.63Ω L=0.62mH The data are typical values. 16 14 12 10 8 6 4 2 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Motor current, IOH -- A Figure 6 Substrate temperature rise, ΔTc - Hybrid IC internal average power dissipation, PD ∆Tc -- PD Substrate temperature rise, ∆Tc -- °C 80 With no heat sink, the IC vertical, and convection cooling 70 60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 Hybrid IC internal average power dissipation, PD -- W Figure 7 Heat sinkthermal resistance, θc-a - Heat sink area, S S -- θc-a Heat sinkthermal resistance, θc-a -- °C/W 100 7 5 3 2 Wit h 10 Wit h 7 5 a bl 3 2 1.0 10 2 3 5 7 no s u rfac e fi nish ack ing surf ace fini shin g 100 2 3 5 7 1000 Heat sink area, S -- cm2 No. A2140-10/11 STK672-120-SL-E SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. Regarding monolithic semiconductors, if you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of October, 2012. Specifications and information herein are subject to change without notice. PS No. A2140-11/11