TI MSP430FW427IPM

SLAS383 − OCTOBER 2003
D Low Supply-Voltage Range, 1.8 V . . . 3.6 V
D Ultralow-Power Consumption:
D
D
D
D
D
D
D
D
D
D Serial Onboard Programming,
− Active Mode: 200 µA at 1 MHz, 2.2 V
− Standby Mode: 0.7 µA
− Off Mode (RAM Retention): 0.1 µA
Five Power-Saving Modes
Wake-Up From Standby Mode in less
than 6 µs
Frequency-Locked Loop, FLL+
16-Bit RISC Architecture, 125-ns
Instruction Cycle Time
Scan IF for Background Water, Heat, and
Gas Volume Measurement
16-Bit Timer_A With Three
Capture/Compare Registers
16-Bit Timer_A With Five
Capture/Compare Registers
Integrated LCD Driver for 96 Segments
On-Chip Comparator
D
D
D
D
D
D
No External Programming Voltage Needed
Programmable Code Protection by Security
Fuse
Brownout Detector
Supply Voltage Supervisor/Monitor With
Programmable Level Detection
Bootstrap Loader in Flash Devices
Family Members Include:
− MSP430FW423:
8KB + 256B Flash Memory,
256B RAM
− MSP430FW425:
16KB + 256B Flash Memory,
512B RAM
− MSP430FW427:
32KB + 256B Flash Memory,
1KB RAM
Available in 64-Pin Quad Flat Pack (QFP)
For Complete Module Descriptions, Refer
to the MSP430x4xx Family User’s Guide,
Literature Number SLAU056
description
The Texas Instruments MSP430 family of ultralow power microcontrollers consist of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low power
modes is optimized to achieve extended battery life in portable measurement applications. The device features
a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 6µs.
The MSP430xW42x series are microcontroller configurations with two built-in 16-bit timers, a comparator, 96
LCD segment drive capability, a scan interface, and 48 I/O pins.
Typical applications include sensor systems that capture analog signals, convert them to digital values, and
process the data and transmit them to a host system. The comparator and timers make the configurations ideal
for gas, heat, and water meters, industrial meters, counter applications, handheld meters, etc.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
−40°C to 85°C
PLASTIC 64-PIN QFP
(PM)
MSP430FW423IPM
MSP430FW425IPM
MSP430FW427IPM
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2003, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # # "#
'' *+( '"! $!#, '# #!#&+ !&"'#
#, && $##(
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLAS383 − OCTOBER 2003
AVCC
DVSS
AVSS
P6.2/SIFCH2
P6.1/SIFCH1
P6.0/SIFCH0
RST/NMI
TCK
TMS
TDI/TCLK
TDO/TDI
P1.0/TA0.0
P1.1/TA0.0/MCLK
P1.2/TA0.1
P1.3/TA1.0/SVSOUT
P1.4/TA1.0
pin designation, MSP430xW42x
1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
2
47
3
46
4
45
5
44
6
43
7
42
8
MSP430xW42x
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
P4.4/S5
P4.3/S6
P4.2/S7
P4.1/S8
P4.0/S9
P3.7/S10
P3.6/S11
P3.5/S12
P3.4/S13
P3.3/S14
P3.2/S15
P3.1/S16
P3.0/S17
P2.7/SIFCLKG/S18
P2.6/CAOUT/S19
P2.5/TA1CLK/S20
DVCC
P6.3/SIFCH3/SIFCAOUT
P6.4/SIFCI0
P6.5/SIFCI1
P6.6/SIFCI2/SIFDACOUT
P6.7/SIFCI3/SVSIN
SIFCI
XIN
XOUT
SIFVSS
SIFCOM
P5.1/S0
P5.0/S1
P4.7/S2
P4.6/S3
P4.5/S4
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
P1.5/TA0CLK/ACLK
P1.6/CA0
P1.7/CA1
P2.0/TA0.2
P2.1/TA1.1
P5.7/R33
P5.6/R23
P5.5/R13
R03
P5.4/COM3
P5.3/COM2
P5.2/COM1
COM0
P2.2/TA1.2/S23
P2.3/TA1.3/S22
P2.4/TA1.4/S21
SLAS383 − OCTOBER 2003
functional block diagram
XIN
XOUT
Oscillator
FLL+
DVCC
DVSS
AVCC
AVSS
RST/NMI
P5
P6
P3
P4
ACLK
8 KB Flash
256 B RAM
Scan IF
I/O Port 5/6
I/O Port 3/4
SMCLK
16 KB Flash
512 B RAM
16 I/Os
16 I/Os
32 KB Flash
1 KB RAM
Up to 4
sensors
System Clock
P1
P2
I/O Port 1/2
16 I/Os, With
Interrupt
Capability
MCLK
Test
MAB,
4 Bit
MAB, 16 Bit
JTAG
CPU
MCB
Emulation
Module
Incl. 16 Reg.
Bus
Conv
MDB, 16 Bit
MDB, 8 Bit
4
TMS
TCK
Watchdog
Timer
TDI/TCLK
TDO/TDI
15 / 16 Bit
Timer0_A
3 CC−Reg
Timer1_A
5 CC−Reg
POR
SVS
Brownout
Comparator
A
Basic
Timer1
1 Interrupt
Vector
LCD
96
Segments
1,2,3,4 MUX
fLCD
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SLAS383 − OCTOBER 2003
Terminal Functions
MSP430xW42x
TERMINAL
NAME
NO.
I/O
DESCRIPTION
AVCC
64
Positive terminal that supplies SVS, brownout, oscillator, FLL+, comparator_A, scan IF AFE, port 6,
and LCD resistive divider circuitry; must not power up prior to DVCC.
AVSS
62
Negative terminal that supplies SVS, brownout, oscillator, FLL+, comparator_A, scan IF AFE. and port
6. Must be externally connected to DVSS. Internally connected to DVSS.
DVCC
1
Digital supply voltage, positive terminal. Supplies all parts, except those which are supplied via AVCC.
DVSS
63
SIFVSS
P1.0/TA0.0
10
Digital supply voltage, negative terminal. Supplies all digital parts, except those which are supplied via
AVCC/AVSS.
Scan IF AFE reference supply voltage.
53
I/O
General-purpose digital I/O/Timer0_A. Capture: CCI0A input, compare: Out0 output/BSL Transmit
P1.1/TA0.0/MCLK
52
I/O
General-purpose digital I/O/Timer0_A. Capture: CCI0B input/MCLK output/BSL Receive.
Note: TA0.0 is only an input on this pin.
P1.2/TA0.1
51
I/O
General-purpose digital I/O/Timer0_A, capture: CCI1A input, compare: Out1 output
P1.3/TA1.0/
SVSOUT
50
I/O
General-purpose digital I/O/Timer1_A, capture: CCI0B input/SVS: output of SVS comparator. Note:
TA1.0 is only an input on this pin.
P1.4/TA1.0
49
I/O
General-purpose digital I/O/Timer1_A, capture: CCI0A input, compare: Out0 output
P1.5/TA0CLK/
ACLK
48
I/O
General-purpose digital I/O/input of Timer0_A clock/output of ACLK
P1.6/CA0
47
I/O
General-purpose digital I/O/Comparator_A input
P1.7/CA1
46
I/O
General-purpose digital I/O/Comparator_A input
P2.0/TA0.2
45
I/O
General-purpose digital I/O/Timer0_A, capture: CCI2A input, compare: Out2 output
P2.1/TA1.1
44
I/O
General-purpose digital I/O/Timer0_A, capture: CCI1A input, compare: Out1 output
P2.2/TA1.2/S23
35
I/O
General-purpose digital I/O/Timer1_A, capture: CCI2A input, compare: Out2 output/LCD segment
output 23 (see Note)
P2.3/TA1.3/S22
34
I/O
General-purpose digital I/O/Timer1_A, capture: CCI3A input, compare: Out3 output/LCD segment
output 22 (see Note)
P2.4/TA1.4/S21
33
I/O
General-purpose digital I/O/Timer1_A, capture: CCI4A input, compare: Out4 output/LCD segment
output 21 (see Note)
P2.5/TA1CLK/S20
32
I/O
General-purpose digital I/O/input of Timer1_A clock/LCD segment output 20 (see Note)
P2.6/CAOUT/S19
31
I/O
General-purpose digital I/O/Comparator_A output/LCD segment output 19 (see Note)
P2.7/SIFCLKG/
S18
30
I/O
General-purpose digital I/O/Scan IF, signal SIFCLKG from internal clock generator/LCD segment
output 18 (see Note)
P3.0/S17
29
I/O
General-purpose digital I/O/ LCD segment output 17 (see Note)
P3.1/S16
28
I/O
General-purpose digital I/O/ LCD segment output 16 (see Note)
P3.2/S15
27
I/O
General-purpose digital I/O/ LCD segment output 15 (see Note)
P3.3/S14
26
I/O
General-purpose digital I/O/ LCD segment output 14 (see Note)
P3.4/S13
25
I/O
General-purpose digital I/O/LCD segment output 13 (see Note)
P3.5/S12
24
I/O
General-purpose digital I/O/LCD segment output 12 (see Note)
P3.6/S11
23
I/O
General-purpose digital I/O/LCD segment output 11 (see Note)
P3.7/S10
22
I/O
General-purpose digital I/O/LCD segment output 10 (see Note)
NOTE 1: LCD function selected automatically when applicable LCD module control bits are set, not with PxSEL bits.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
Terminal Functions (Continued)
MSP430xW42x
TERMINAL
NAME
NO.
I/O
DESCRIPTION
P4.0/S9
21
I/O
General-purpose digital I/O/LCD segment output 9 (see Note)
P4.1/S8
20
I/O
General-purpose digital I/O/LCD segment output 8 (see Note)
P4.2/S7
19
I/O
General-purpose digital I/O/LCD segment output 7 (see Note)
P4.3/S6
18
I/O
General-purpose digital I/O/LCD segment output 6 (see Note)
P4.4/S5
17
I/O
General-purpose digital I/O/LCD segment output 5 (see Note)
P4.5/S4
16
I/O
General-purpose digital I/O/LCD segment output 4 (see Note)
P4.6/S3
15
I/O
General-purpose digital I/O/LCD segment output 3 (see Note)
P4.7/S2
14
I/O
General-purpose digital I/O/LCD segment output 2 (see Note)
P5.0/S1
13
I/O
General-purpose digital I/O/LCD segment output 1 (see Note)
P5.1/S0
12
I/O
General-purpose digital I/O/LCD segment output 0 (see Note)
COM0
36
O
Common output. COM0−3 are used for LCD backplanes
P5.2/COM1
37
I/O
General-purpose digital I/O/common output. COM0−3 are used for LCD backplanes
P5.3/COM2
38
I/O
General-purpose digital I/O/common output. COM0−3 are used for LCD backplanes
P5.4/COM3
39
I/O
General-purpose digital I/O/common output. COM0−3 are used for LCD backplanes
R03
40
I
P5.5/R13
41
I/O
General-purpose digital I/O/input port of third most positive analog LCD level (V4 or V3)
P5.6/R23
42
I/O
General-purpose digital I/O/input port of second most positive analog LCD level (V2)
P5.7/R33
43
I/O
General-purpose digital I/O/output port of most positive analog LCD level (V1)
P6.0/SIFCH0
59
I/O
General-purpose digital I/O/Scan IF, channel 0 sensor excitation output and signal input
P6.1/SIFCH1
60
I/O
General-purpose digital I/O/Scan IF, channel 1 sensor excitation output and signal input
P6.2/SIFCH2
61
I/O
General-purpose digital I/O/Scan IF, channel 2 sensor excitation output and signal input
P6.3/SIFCH3/
SIFCAOUT
2
I/O
General-purpose digital I/O/Scan IF, channel 3 sensor excitation output and signal input/Scan IF
comparator output
P6.4/SIFCI0
3
I/O
General-purpose digital I/O/Scan IF, channel 0 signal input to comparator
P6.5/SIFCI1
4
I/O
General-purpose digital I/O/Scan IF, channel 1 signal input to comparator
P6.6/SIFCI2/
SIFDACOUT
5
I/O
General-purpose digital I/O/Scan IF, channel 2 signal input to comparator/10-bit DAC output
P6.7/
SIFCI3/SVSIN
6
I/O
General-purpose digital I/O/Scan IF, channel 3 signal input to comparator/SVS, analog input
Input port of fourth positive (lowest) analog LCD level (V5)
SIFCI
7
I
Scan IF input to Comparator.
SIFCOM
11
O
Common termination for Scan IF sensors.
RST/NMI
58
I
Reset input or nonmaskable interrupt input port.
TCK
57
I
Test clock. TCK is the clock input port for device programming and test.
TDI/TCLK
55
I
Test data input or test clock input. The device protection fuse is connected to TDI/TCLK.
TDO/TDI
54
I/O
TMS
56
I
Test mode select. TMS is used as an input port for device programming and test.
XIN
8
I
Input port for crystal oscillator XT1. Standard or watch crystals can be connected.
XOUT
9
O
Output terminal of crystal oscillator XT1.
Test data output port. TDO/TDI data output or programming data input terminal.
NOTE 1: LCD function selected automatically when applicable LCD module control bits are set, not with PxSEL bits.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLAS383 − OCTOBER 2003
short-form description
CPU
The MSP430 CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions,
are performed as register operations in
conjunction with seven addressing modes for
source operand and four addressing modes for
destination operand.
Program Counter
PC/R0
Stack Pointer
SP/R1
SR/CG1/R2
Status Register
Constant Generator
The CPU is integrated with 16 registers that
provide reduced instruction execution time. The
register-to-register operation execution time is
one cycle of the CPU clock.
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register,
and constant generator respectively. The
remaining registers are general-purpose
registers.
Peripherals are connected to the CPU using data,
address, and control buses, and can be handled
with all instructions.
instruction set
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 1 shows examples of the three types of
instruction formats; the address modes are listed
in Table 2.
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
General-Purpose Register
R11
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
Table 1. Instruction Word Formats
Dual operands, source-destination
e.g. ADD R4,R5
R4 + R5 −−−> R5
Single operands, destination only
e.g. CALL
PC −−>(TOS), R8−−> PC
Relative jump, un/conditional
e.g. JNE
R8
Jump-on-equal bit = 0
Table 2. Address Mode Descriptions
ADDRESS MODE
SYNTAX
EXAMPLE
OPERATION
Register
D
D
MOV Rs,Rd
MOV R10,R11
Indexed
D
D
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
Symbolic (PC relative)
D
D
MOV EDE,TONI
M(EDE) −−> M(TONI)
Absolute
D
D
MOV &MEM,&TCDAT
M(MEM) −−> M(TCDAT)
Indirect
D
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) −−> M(Tab+R6)
Indirect
autoincrement
D
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) −−> R11
R10 + 2−−> R10
D
MOV #X,TONI
MOV #45,TONI
Immediate
NOTE: S = source
6
S D
D = destination
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
R10
−−> R11
M(2+R5)−−> M(6+R6)
#45
−−> M(TONI)
SLAS383 − OCTOBER 2003
operating modes
The MSP430 has one active mode and five software selectable low-power modes of operation. An interrupt
event can wake up the device from any of the five low-power modes, service the request and restore back to
the low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
D Active mode AM;
−
All clocks are active
D Low-power mode 0 (LPM0);
−
CPU is disabled
ACLK and SMCLK remain active, MCLK is available to modules
FLL+ Loop control remains active
D Low-power mode 1 (LPM1);
−
CPU is disabled
ACLK and SMCLK remain active, MCLK is available to modules
FLL+ Loop control is disabled
D Low-power mode 2 (LPM2);
−
CPU is disabled
MCLK and FLL+ loop control and DCOCLK are disabled
DCO’s dc-generator remains enabled
ACLK remains active
D Low-power mode 3 (LPM3);
−
CPU is disabled
MCLK, FLL+ loop control, and DCOCLK are disabled
DCO’s dc-generator is disabled
ACLK remains active
D Low-power mode 4 (LPM4);
−
CPU is disabled
ACLK is disabled
MCLK, FLL+ loop control, and DCOCLK are disabled
DCO’s dc-generator is disabled
Crystal oscillator is stopped
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SLAS383 − OCTOBER 2003
interrupt vector addresses
The interrupt vectors and the power-up starting address are located in the ROM with an address range
0FFFFh − 0FFE0h. The vector contains the 16-bit address of the appropriate interrupt-handler instruction
sequence.
INTERRUPT SOURCE
INTERRUPT FLAG
SYSTEM INTERRUPT
WORD ADDRESS
PRIORITY
Power-up
External Reset
Watchdog
Flash memory
WDTIFG
KEYV
(see Note 1)
Reset
0FFFEh
15, highest
NMI
Oscillator Fault
Flash memory access violation
NMIIFG (see Notes 1 and 3)
OFIFG (see Notes 1 and 3)
ACCVIFG (see Notes 1 and 3)
(Non)maskable
(Non)maskable
(Non)maskable
0FFFCh
14
Timer1_A5
TA1CCR0 CCIFG (see Note 2)
Maskable
0FFFAh
13
Timer1_A5
TA1CCR1 to TA1CCR4
CCIFGs
TA1CTL TAIFG
Maskable
0FFF8h
12
Comparator_A
CMPAIFG
Maskable
0FFF6h
11
Watchdog Timer
WDTIFG
Maskable
0FFF4h
10
Scan IF
SIFIFG0 to SIFIFG6
(See Note 1)
Maskable
0FFF2h
9
0FFF0h
8
0FFEEh
7
Timer0_A3
TA0CCR0 CCIFG (see Note 2)
Maskable
0FFECh
6
Timer0_A3
TA0CCR1 and TA0CCR2
CCIFGs, and TA0CTL TAIFG
(see Notes 1 and 2)
Maskable
0FFEAh
5
I/O port P1 (eight flags)
P1IFG.0 (see Notes 1 and 2)
To
P1IFG.7 (see Notes 1 and 2)
Maskable
0FFE8h
4
0FFE6h
3
0FFE4h
2
I/O port P2 (eight flags)
P2IFG.0 (see Notes 1 and 2)
To
P2IFG.7 (see Notes 1 and 2)
Maskable
0FFE2h
1
Basic Timer1
BTIFG
Maskable
0FFE0h
0, lowest
NOTES: 1. Multiple source flags
2. Interrupt flags are located in the module.
3. (Non)maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt-enable cannot.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
special function registers
Most interrupt and module enable bits are collected into the lowest address space. Special function register bits
that are not allocated to a functional purpose are not physically present in the device. Simple software access
is provided with this arrangement.
interrupt enable 1 and 2
7
Address
6
0h
5
4
ACCVIE
NMIIE
rw-0
7
Address
1h
6
3
2
rw-0
5
1
0
OFIE
WDTIE
rw-0
4
3
2
rw-0
1
0
BTIE
rw-0
WDTIE:
Watchdog-timer interrupt enable. Inactive if watchdog mode is selected. Active if watchdog timer is
configured in interval timer mode.
OFIE:
Oscillator-fault-interrupt enable
NMIIE:
Nonmaskable-interrupt enable
ACCVIE:
Flash access violation interrupt enable
BTIE:
Basic Timer1 interrupt enable
interrupt flag register 1 and 2
7
Address
6
5
02h
4
3
2
NMIIFG
rw-0
7
Address
3h
6
5
1
0
OFIFG
WDTIFG
rw-1
4
3
2
rw-0
1
0
BTIFG
rw-0
WDTIFG:
Set on watchdog-timer overflow (in watchdog mode) or security key violation. Reset with VCC power-up,
or a reset condition at the RST/NMI pin in reset mode.
OFIFG:
Flag set on oscillator fault
NMIIFG:
Set via RST/NMI pin
BTIFG:
Basic Timer1 interrupt flag
module enable registers 1 and 2
Address
7
6
5
4
3
2
1
0
04h/05h
Legend: rw:
rw-0:
Bit Can Be Read and Written
Bit Can Be Read and Written. It Is Reset by PUC.
SFR Bit Not Present in Device
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SLAS383 − OCTOBER 2003
memory organization
MSP430FW423
MSP430FW425
MSP430FW427
Size
Flash
Flash
8KB
0FFFFh − 0FFE0h
0FFFFh − 0E000h
16KB
0FFFFh − 0FFE0h
0FFFFh − 0C000h
32KB
0FFFFh − 0FFE0h
0FFFFh − 08000h
Information memory
Size
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
Boot memory
Size
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
Size
256 Byte
02FFh − 0200h
512 Byte
03FFh − 0200h
1KB
05FFh − 0200h
16-bit
8-bit
8-bit SFR
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
Memory
Interrupt vector
Code memory
RAM
Peripherals
bootstrap loader (BSL)
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete
description of the features of the BSL and its implementation, see the Application report Features of the MSP430
Bootstrap Loader, Literature Number SLAA089.
BSL Function
PM Package Pins
Data Transmit
53 - P1.0
Data Receive
52 - P1.1
flash memory
The flash memory can be programmed via the JTAG port, the bootstrap loader, or in-system by the CPU. The
CPU can perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
D Flash memory has n segments of main memory and two segments of information memory (A and B) of 128
bytes each. Each segment in main memory is 512 bytes in size.
D Segments 0 to n may be erased in one step, or each segment may be individually erased.
D Segments A and B can be erased individually, or as a group with segments 0−n.
Segments A and B are also called information memory.
D New devices may have some bytes programmed in the information memory (needed for test during
manufacturing). The user should perform an erase of the information memory prior to the first use.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
flash memory (continued)
8KB
16KB
0FFFFh 0FFFFh
32KB
0FFFFh
0FE00h 0FE00h 0FE00h
0FDFFh 0FDFFh 0FDFFh
Segment 0
With Interrupt Vectors
Segment 1
0FC00h 0FC00h 0FC00h
0FBFFh 0FBFFh 0FBFFh
Segment 2
0FA00h
0F9FFh
0FA00h
0F9FFh
0FA00h
0F9FFh
Main Memory
0E400h 0C400h
0E3FFh 0C3FFh
083FFh
0E200h 0C200h
0E1FFh 0C1FFh
08200h
081FFh
0E000h
010FFh
0C000h
010FFh
08000h
010FFh
01080h
0107Fh
01080h
0107Fh
01080h
0107Fh
08400h
Segment n−1
Segment n
Segment A
Information Memory
Segment B
01000h
01000h
01000h
peripherals
Peripherals are connected to the CPU through data, address, and control busses and can be handled using
all instructions. For complete module descriptions, refer to the MSP430x4xx Family User’s Guide, literature
number SLAU056.
oscillator and system clock
The clock system in the MSP430xW42x family of devices is supported by the FLL+ module that includes support
for a 32768-Hz watch crystal oscillator, an internal digitally-controlled oscillator (DCO) and a high frequency
crystal oscillator. The FLL+ clock module is designed to meet the requirements of both low system cost and
low-power consumption. The FLL+ features a digital frequency locked loop (FLL) hardware which in conjunction
with a digital modulator stabilizes the DCO frequency to a programmable multiple of the watch crystal frequency.
The internal DCO provides a fast turn-on clock source and stabilizes in less than 6 µs. The FLL+ module
provides the following clock signals:
D
D
D
D
Auxiliary clock (ACLK), sourced from a 32768-Hz watch crystal or a high frequency crystal.
Main clock (MCLK), the system clock used by the CPU.
Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules.
ACLK/n, the buffered output of ACLK, ACLK/2, ACLK/4, or ACLK/8.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SLAS383 − OCTOBER 2003
brownout, supply voltage supervisor
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on
and power off. The supply voltage supervisor (SVS) circuitry detects if the supply voltage drops below a user
selectable level and supports both supply voltage supervision (the device is automatically reset) and supply
voltage monitoring (SVM, the device is not automatically reset).
The CPU begins code execution after the brownout circuit releases the device reset. However, VCC may not
have ramped to VCC(min) at that time. The user must insure the default FLL+ settings are not changed until VCC
reaches VCC(min). If desired, the SVS circuit can be used to determine when VCC reaches VCC(min).
digital I/O
There are six 8-bit I/O ports implemented—ports P1 through P6:
D
D
D
D
All individual I/O bits are independently programmable.
Any combination of input, output, and interrupt conditions is possible.
Edge-selectable interrupt input capability for all the eight bits of ports P1 and P2.
Read/write access to port-control registers is supported by all instructions.
Basic Timer1
The Basic Timer1 has two independent 8-bit timers which can be cascaded to form a 16-bit timer/counter. Both
timers can be read and written by software. The Basic Timer1 can be used to generate periodic interrupts and
clock for the LCD module.
LCD drive
The LCD driver generates the segment and common signals required to drive an LCD display. The LCD
controller has dedicated data memory to hold segment drive information. Common and segment signals are
generated as defined by the mode. Static, 2-MUX, 3-MUX, and 4-MUX LCDs are supported by this peripheral.
watchdog timer
The primary function of the watchdog timer (WDT) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be configured as an interval timer and can generate
interrupts at selected time intervals.
comparator_A
The primary function of the comparator_A module is to support precision slope analog−to−digital conversions,
battery−voltage supervision, and monitoring of external analog signals.
scan IF
The scan interface is used to measure linear or rotational motion and supports LC and resistive sensors such
as GMR sensors. The scan IF incorporates a VCC/2 generator, a comparator, and a 10-bit DAC and supports
up to four sensors.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
timer0_A3
Timer0_A3 is a 16-bit timer/counter with three capture/compare registers. Timer0_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer0_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer0_A3 Signal Connections
Input Pin Number
Device Input Signal
Module Input Name
48 - P1.5
TA0CLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
48 - P1.5
TA0CLK
INCLK
53 - P1.0
TA0.0
CCI0A
52 - P1.1
TA0.0
CCI0B
DVSS
DVCC
GND
51 - P1.2
45 - P2.0
TA0.1
VCC
CCI1A
CAOUT (internal)
CCI1B
DVSS
DVCC
GND
TA0.2
VCC
CCI2A
ACLK (internal)
CCI2B
DVSS
DVCC
GND
Module Block
Module Output Signal
Timer
NA
Output Pin Number
53 - P1.0
CCR0
TA0.0
51 - P1.2
CCR1
TA0.1
45 - P2.0
CCR2
TA0.2
VCC
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SLAS383 − OCTOBER 2003
timer1_A5
Timer1_A5 is a 16-bit timer/counter with five capture/compare registers. Timer1_A5 can support multiple
capture/compares, PWM outputs, and interval timing. Timer1_A5 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer1_A5 Signal Connections
Input Pin Number
Device Input Signal
Module Input Name
32 - P2.5
TA1CLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
32 - P2.5
TA1CLK
INCLK
49 - P1.4
TA1.0
CCI0A
50 - P1.3
TA1.0
CCI0B
DVSS
DVCC
GND
44 - P2.1
35 - P2.2
34 - P2.3
33 - P2.4
14
TA1.1
VCC
CCI1A
CAOUT (internal)
CCI1B
DVSS
DVCC
GND
TA1.2
VCC
CCI2A
SIFO0sig (internal)
CCI2B
DVSS
DVCC
GND
TA1.3
VCC
CCI3A
SIFO1sig (internal)
CCI3B
DVSS
DVCC
GND
TA1.4
VCC
CCI4A
SIFO2sig (internal)
CCI4B
DVSS
DVCC
GND
Module Block
Module Output Signal
Timer
NA
49 - P1.4
CCR0
TA1.0
44 - P2.1
CCR1
TA1.1
35 - P2.2
CCR2
TA1.2
34 - P2.3
CCR3
TA1.3
33 - P2.4
CCR4
VCC
POST OFFICE BOX 655303
Output Pin Number
• DALLAS, TEXAS 75265
TA1.4
SLAS383 − OCTOBER 2003
peripheral file map
PERIPHERALS WITH WORD ACCESS
Watchdog
Watchdog Timer control
WDTCTL
0120h
Timer1_A5
Timer1_A interrupt vector
TA1IV
011Eh
Timer1_A control
TA1CTL
0180h
Capture/compare control 0
TA1CCTL0
0182h
Capture/compare control 1
TA1CCTL1
0184h
Capture/compare control 2
TA1CCTL2
0186h
Capture/compare control 3
TA1CCTL3
0188h
Capture/compare control 4
TA1CCTL4
018Ah
Reserved
018Ch
Reserved
018Eh
Timer1_A register
TA1R
0190h
Capture/compare register 0
TA1CCR0
0192h
Capture/compare register 1
TA1CCR1
0194h
Capture/compare register 2
TA1CCR2
0196h
Capture/compare register 3
TA1CCR3
0198h
Capture/compare register 4
TA1CCR4
019Ah
Reserved
019Ch
Reserved
Timer0_A3
019Eh
Timer0_A interrupt vector
TA0IV
012Eh
Timer0_A control
TA0CTL0
0160h
Capture/compare control 0
TA0CCTL0
0162h
Capture/compare control 1
TA0CCTL1
0164h
Capture/compare control 2
TA0CCTL2
0166h
Reserved
0168h
Reserved
016Ah
Reserved
016Ch
Reserved
016Eh
Timer0_A register
TA0R
0170h
Capture/compare register 0
TA0CCR0
0172h
Capture/compare register 1
TA0CCR1
0174h
Capture/compare register 2
TA0CCR2
0176h
Reserved
0178h
Reserved
017Ah
Reserved
017Ch
Reserved
Flash
017Eh
Flash control 3
FCTL3
012Ch
Flash control 2
FCTL2
012Ah
Flash control 1
FCTL1
0128h
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SLAS383 − OCTOBER 2003
PERIPHERALS WITH WORD ACCESS (CONTINUED)
Scan IF
SIF timing state machine 23
SIFTSM23
01FEh
:
:
:
SIF timing state machine 0
SIFTSM0
01D0h
SIF DAC register 7
SIFDACR7
01CEh
:
:
:
SIF DAC register 0
SIFDACR0
01C0h
SIF control register 5
SIFCTL5
01BEh
SIF control register 4
SIFCTL4
01BCh
SIF control register 3
SIFCTL3
01BAh
SIF control register 2
SIFCTL2
01B8h
SIF control register 1
SIFCTL1
01B6h
SIF processing state machine
SIFTPSMV
01B4h
SIF counter CNT1/2
SIFCNT
01B2h
Reserved
SIFDEBUG
01B0h
LCD memory 20
LCDM20
0A4h
:
:
:
LCD memory 16
LCDM16
0A0h
LCD memory 15
LCDM15
09Fh
:
:
:
LCD memory 1
LCDM1
091h
LCD control and mode
LCDCTL
090h
Comparator_A port disable
CAPD
05Bh
Comparator_A control2
CACTL2
05Ah
PERIPHERALS WITH BYTE ACCESS
LCD
Comparator_A
Comparator_A control1
CACTL1
059h
Brownout, SVS
SVS control register
SVSCTL
056h
FLL+ Clock
FLL+ Control1
FLL_CTL1
054h
FLL+ Control0
FLL_CTL0
053h
System clock frequency control
SCFQCTL
052h
System clock frequency integrator
SCFI1
051h
System clock frequency integrator
SCFI0
050h
BT counter2
BTCNT2
047h
BT counter1
BTCNT1
046h
BT control
BTCTL
040h
Basic Timer1
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
peripheral file map (continued)
PERIPHERALS WITH BYTE ACCESS (CONTINUED)
Port P6
Port P5
Port P4
Port P3
Port P2
Port P1
Special Functions
Port P6 selection
P6SEL
037h
Port P6 direction
P6DIR
036h
Port P6 output
P6OUT
035h
Port P6 input
P6IN
034h
Port P5 selection
P5SEL
033h
Port P5 direction
P5DIR
032h
Port P5 output
P5OUT
031h
Port P5 input
P5IN
030h
Port P4 selection
P4SEL
01Fh
Port P4 direction
P4DIR
01Eh
Port P4 output
P4OUT
01Dh
Port P4 input
P4IN
01Ch
Port P3 selection
P3SEL
01Bh
Port P3 direction
P3DIR
01Ah
Port P3 output
P3OUT
019h
Port P3 input
P3IN
018h
Port P2 selection
P2SEL
02Eh
Port P2 interrupt enable
P2IE
02Dh
Port P2 interrupt-edge select
P2IES
02Ch
Port P2 interrupt flag
P2IFG
02Bh
Port P2 direction
P2DIR
02Ah
Port P2 output
P2OUT
029h
Port P2 input
P2IN
028h
Port P1 selection
P1SEL
026h
Port P1 interrupt enable
P1IE
025h
Port P1 interrupt-edge select
P1IES
024h
Port P1 interrupt flag
P1IFG
023h
Port P1 direction
P1DIR
022h
Port P1 output
P1OUT
021h
Port P1 input
P1IN
020h
SFR module enable 2
ME2
005h
SFR module enable 1
ME1
004h
SFR interrupt flag2
IFG2
003h
SFR interrupt flag1
IFG1
002h
SFR interrupt enable2
IE2
001h
SFR interrupt enable1
IE1
000h
absolute maximum ratings†
Voltage applied at VCC to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to + 4.1 V
Voltage applied to any pin (see Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VCC + 0.3 V
Diode current at any device terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2 mA
Storage temperature (unprogrammed device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Storage temperature (programmed device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltages referenced to VSS. The JTAG fuse-blow voltage, VFB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TDI/TCLK pin when blowing the JTAG fuse.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SLAS383 − OCTOBER 2003
recommended operating conditions
PARAMETER
MIN
NOM
MAX
UNITS
Supply voltage during program execution, SVS disabled
VCC (AVCC = DVCC = VCC)
MSP430xW42x
1.8
3.6
V
Supply voltage during program execution, SVS enabled (see Note 1),
VCC (AVCC = DVCC = VCC)
MSP430xW42x
2.2
3.6
V
Supply voltage during programming flash memory,
VCC (AVCC = DVCC = VCC)
MSP430FW42x
2.7
3.6
V
0
0
V
MSP430xW42x
−40
85
°C
Supply voltage, VSS (AVSS = DVSS = VSS)
Operating free-air temperature range, TA
LFXT1 crystal frequency, f(LFXT1)
(see Note 2)
LF selected, XTS_FLL=0
Watch crystal
32768
XT1 selected, XTS_FLL=1
Ceramic resonator
XT1 selected, XTS_FLL=1
Crystal
Hz
450
8000
kHz
1000
8000
kHz
DC
4.15
DC
8
Processor frequency (signal MCLK), f(System)
VCC = 1.8 V
VCC = 3.6 V
Low-level input voltage (TCK, TMS, TDI/TCLK, RST/NMI), VIL
(excluding XIN)
VCC = 2.2 V/3 V
VSS
VSS+0.6
V
High-level input voltage (TCK, TMS, TDI/TCLK, RST/NMI), VIH
(excluding XIN)
VCC = 2.2 V/3 V
0.8×VCC
VCC
V
MHz
f(System) − Maximum Processor Frequency − MHz
NOTES: 1. The minimum operating supply voltage is defined according to the trip point where POR is going active by decreasing supply voltage.
POR is going inactive when the supply voltage is raised above minimum supply voltage plus the hysteresis of the SVS circuitry.
2. The LFXT1 oscillator in LF-mode requires a watch crystal.
Supply Voltage Range
During Programming of
the Flash Memory
f (MHz)
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
8 MHz
Supply Voltage Range, xW42x
During Program Execution
4.15 MHz
1.8 V
2.7 V
3V
3.6 V
VCC − Supply Voltage − V
Figure 1. Maximum Frequency vs Supply Voltage
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted)
supply current into AVCC + DVCC excluding external current, (see Note 1)
PARAMETER
TEST CONDITIONS
Active mode,
f(MCLK) = f(SMCLK) = 1 MHz,
f(ACLK) = 32,768 Hz, XTS_FLL = 0
(FW42x: Program executes in flash)
I(AM)
I(LPM0)
I(LPM2)
I(LPM3)
MIN
NOM
MAX
VCC = 2.2 V
200
250
VCC = 3 V
300
350
VCC = 2.2 V
57
70
VCC = 3 V
92
100
VCC = 2.2 V
VCC = 3 V
11
14
17
22
TA = −40°C
TA = −10°C
0.95
1.4
0.8
1.3
TA = 25°C
TA = 60°C
0.7
1.2
A
µA
TA = −40°C to 85°C
Low-power mode, (LPM0)
f(MCLK) = f(SMCLK) = 1 MHz,
f(ACLK) = 32,768 Hz, XTS_FLL = 0
FN_8=FN_4=FN_3=FN_2=0
TA = −40°C to 85°C
Low-power mode, (LPM2)
TA = −40°C to 85°C
Low-power mode, (LPM3) (see Note 2)
UNIT
A
µA
VCC = 2.2 V
0.95
1.4
TA = 85°C
TA = −40°C
1.6
2.3
1.1
1.7
TA = −10°C
TA = 25°C
1.0
1.6
0.9
1.5
TA = 60°C
TA = 85°C
1.1
1.7
2.0
2.6
TA = −40°C
TA = 25°C
0.1
0.5
VCC = 3 V
µA
A
µA
A
0.1
0.5
VCC = 2.2 V/3 V
µA
TA = 85°C
0.8
2.5
NOTES: 1. All inputs are tied to 0 V or VCC. Outputs do not source or sink any current. The current consumption is measured with active Basic
Timer1 and LCD (ACLK selected).
The current consumption of the Comparator_A and the SVS module are specified in the respective sections.
2. The LPM3 currents are characterized with a KDS Daishinku DT−38 (6 pF) crystal.
I(LPM4)
Low-power mode, (LPM4)
current consumption of active mode versus system frequency, F version
I(AM) = I(AM) [1 MHz] × f(System) [MHz]
current consumption of active mode versus supply voltage, F version
I(AM) = I(AM) [3 V] + 140 µA/V × (VCC – 3 V)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Schmitt-trigger inputs − Ports P1, P2, P3, P4, P5, and P6; RST/NMI; JTAG: TCK, TMS, TDI/TCLK, TDO
PARAMETER
TEST CONDITIONS
VIT+
Positive-going input threshold voltage
VIT−
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ − VIT−)
MIN
TYP
MAX
VCC = 2.2 V
VCC = 3 V
VCC = 2.2 V
1.1
1.5
1.5
1.9
0.4
0.9
VCC = 3 V
VCC = 2.2 V
0.9
1.3
0.3
1.1
0.45
1
VCC = 3 V
UNIT
V
V
V
inputs Px.x, TAx.x
PARAMETER
t(int)
TEST CONDITIONS
VCC
2.2 V/3 V
Port P1, P2: P1.x to P2.x, External trigger signal
for the interrupt flag, (see Note 1)
External interrupt timing
t(cap)
Timer_A, capture timing
TAx.x
f(TAext)
Timer_A clock frequency
externally applied to pin
TAxCLK, INCLK t(H) = t(L)
f(TAint)
Timer_A clock frequency
SMCLK or ACLK signal selected
MIN
TYP
MAX
1.5
2.2 V
62
3V
50
2.2 V
62
3V
50
UNIT
cycle
ns
ns
2.2 V
8
3V
10
2.2 V
8
3V
10
MHz
MHz
NOTES: 1. The external signal sets the interrupt flag every time the minimum t(int) cycle and time parameters are met. It may be set even with
trigger signals shorter than t(int). Both the cycle and timing specifications must be met to ensure the flag is set. t(int) is measured in
MCLK cycles.
leakage current (see Note 1)
PARAMETER
Ilkg(P1.x)
Ilkg(P6.x)
TEST CONDITIONS
Leakage current
Port P1
Port 1: V(P1.x) (see Note 2)
Leakage current
Port P6
Port 6: V(P6.x) (see Note 2)
MIN
NOM
VCC = 2.2 V/3 V
VCC = 2.2 V/3 V
MAX
UNIT
±50
nA
±50
nA
NOTES: 1. The leakage current is measured with VSS or VCC applied to the corresponding pin(s), unless otherwise noted.
2. The port pin must be selected as an input.
outputs − Ports P1, P2, P3, P4, P5, and P6
PARAMETER
VOH
VOL
High-level output voltage
Low-level output voltage
TEST CONDITIONS
MIN
IOH(max) = −1.5 mA,
IOH(max) = −6 mA,
VCC = 2.2 V,
VCC = 2.2 V,
See Note 1
IOH(max) = −1.5 mA,
IOH(max) = −6 mA,
VCC = 3 V,
VCC = 3 V,
See Note 1
IOL(max) = 1.5 mA,
IOL(max) = 6 mA,
VCC = 2.2 V,
VCC = 2.2 V,
See Note 1
IOL(max) = 1.5 mA,
IOL(max) = 6 mA,
VCC = 3 V,
VCC = 3 V,
See Note 1
See Note 2
See Note 2
See Note 2
See Note 2
TYP
MAX
VCC−0.25
VCC−0.6
VCC
VCC
VCC−0.25
VCC−0.6
VCC
VCC
VSS
VSS
VSS+0.25
VSS+0.6
VSS
VSS
VSS+0.25
VSS+0.6
UNIT
V
V
NOTES: 1. The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±12 mA to satisfy the maximum
specified voltage drop.
2. The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±24 mA to satisfy the maximum
specified voltage drop.
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
outputs − Ports P1, P2, P3, P4, P5, and P6 (continued)
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
40
20
TA = 85°C
15
10
5
0
0.0
d
TA = 25°C
VCC = 2.2 V
P2.4
IOL − Typical Low-Level Output Current − mA
IOL − Typical Low-Level Output Current − mA
25
0.5
1.0
1.5
2.0
VCC = 3 V
P2.4
35
TA = 85°C
30
25
20
15
10
5
0
0.0
2.5
TA = 25°C
0.5
VOL − Low-Level Output Voltage − V
1.0
Figure 2
3.0
3.5
0
VCC = 2.2 V
P2.4
IOH − Typical High-Level Output Current − mA
IOH − Typical High-Level Output Current − mA
2.5
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
0
−5
−10
−15
−25
0.0
2.0
Figure 3
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
−20
1.5
VOL − Low-Level Output Voltage − V
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
2.5
VOH − High-Level Output Voltage − V
−5
VCC = 3 V
P2.4
−10
−15
−20
−25
−30
−35
TA = 85°C
−40
−45
TA = 25°C
−50
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH − High-Level Output Voltage − V
Figure 4
Figure 5
NOTE A: One output loaded at a time
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
output frequency
PARAMETER
TEST CONDITIONS
fPx.y
(1 ≤ x ≤ 6, 0 ≤ y ≤ 7)
CL = 20 pF,
IL = ± 1.5mA
fACLK,
fMCLK,
fSMCLK
P1.1/TA0.0/MCLK,
P1.5/TA0CLK/ACLK
CL = 20 pF
tXdc
MIN
VCC = 2.2 V
VCC = 3 V
TYP
MAX
DC
10
DC
12
VCC = 2.2 V
UNIT
MHz
8
MHz
VCC = 3 V
12
P1.5/TA0CLK/ACLK,
CL = 20 pF
VCC = 2.2 V / 3 V
fACLK = fLFXT1 = fXT1
fACLK = fLFXT1 = fLF
P1.1/TA0.0/MCLK,
CL = 20 pF,
VCC = 2.2 V / 3 V
fMCLK = fLFXT1/n
50%−
15 ns
50%
50%+
15 ns
fMCLK = fDCOCLK
50%−
15 ns
50%
50%+
15 ns
Duty cycle of output frequency
40%
60%
30%
fACLK = fLFXT1/n
70%
50%
wake-up LPM3 (see Note 1)
PARAMETER
TEST CONDITIONS
MIN
NOM
MAX
t(LPM3) Delay time
VCC = 2.2 V/3 V
NOTES: 1. The delay time t(LPM3) is independent of the system frequency and VCC.
6
UNIT
µs
RAM (see Note 1)
PARAMETER
TEST CONDITIONS
VRAMh
MIN
CPU halted (see Note 1)
TYP
MAX
1.6
UNIT
V
NOTES: 1. This parameter defines the minimum supply voltage when the data in the program memory RAM remain unchanged. No program
execution should take place during this supply voltage condition.
LCD
PARAMETER
V(33)
V(23)
V(13)
V(33) − V(03)
2.5
Voltage at P5.6/R23
Analog voltage
Voltage at P5.5/R13
VCC = 3 V
Voltage at R33/R03
R03 = VSS
Input leakage
P5.5/R13 = VCC/3
P5.6/R23 = 2 × VCC/3
I(R23)
V(Sxx0)
V(Sxx1)
V(Sxx2)
Segment line
voltage
I(Sxx) = −3 µA,
A,
2.5
No load at all
segment and
common lines,
VCC = 3 V
VCC = 3 V
V(Sxx3)
22
MIN
Voltage at P5.7/R33
I(R03)
I(R13)
TEST CONDITIONS
POST OFFICE BOX 655303
TYP
MAX
VCC +0.2
(V33−V03) × 2/3 + V03
(V(33)−V(03)) × 1/3 + V(03)
UNIT
V
VCC +0.2
±20
±20
nA
±20
V(03)
V(13)
V(03) − 0.1
V(13) − 0.1
V(23)
V(33)
V(23) − 0.1
V(33) + 0.1
• DALLAS, TEXAS 75265
V
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Comparator_A (see Note 1)
PARAMETER
TEST CONDITIONS
I(CC)
CAON = 1, CARSEL = 0, CAREF = 0
I(Refladder/RefDiode)
CAON = 1, CARSEL = 0,
CAREF = 1/2/3,
No load at P1.6/CA0/TA1 and P1.7/
CA1/TA2
MIN
TYP
MAX
VCC = 2.2 V
VCC = 3 V
25
40
45
60
VCC = 2.2 V
30
50
VCC = 3 V
45
71
Voltage @ 0.25 V CC node PCA0 = 1, CARSEL = 1, CAREF = 1,
No load at P1.6/CA0 and P1.7/CA1
V CC
VCC = 2.2 V / 3 V
0.23
0.24
0.25
V(Ref050)
Voltage @ 0.5 V CC node
PCA0 = 1, CARSEL = 1, CAREF = 2,
No load at P1.6/CA0 and P1.7/CA1
VCC = 2.2V / 3 V
0.47
0.48
0.50
(See Figure 6 and
Figure 7)
PCA0 = 1, CARSEL = 1, CAREF = 3,
No load at P1.6/CA0 and P1.7/CA1;
TA = 85°C
VCC = 2.2 V
390
480
540
V(RefVT)
VCC = 3.0 V
400
490
550
V(IC)
Common-mode input
voltage range
CAON = 1
VCC = 2. 2V/3 V
0
Offset voltage
See Note 2
VCC = 2.2 V/3 V
−30
Input hysteresis
CAON = 1
VCC = 2.2 V / 3 V
VCC = 2.2 V
V(offset)
Vhys
TA = 25
25°C,
C,
Overdrive 10 mV, without filter: CAF = 0
t(response LH)
TA = 25
25°C
C
Overdrive 10 mV, with filter: CAF = 1
TA = 25
25°C
C
Overdrive 10 mV, without filter: CAF = 0
t(response HL)
µA
A
A
µA
V(Ref025)
V CC
UNIT
mV
VCC = 3 V
VCC = 2.2 V
VCC = 3 V
VCC = 2.2 V
VCC = 3 V
VCC = 2.2 V
VCC−1.0
V
30
mV
0
0.7
1.4
mV
130
210
300
80
150
240
1.4
1.9
3.4
0.9
1.5
2.6
130
210
300
80
150
240
ns
µss
ns
1.4
1.9
3.4
µss
VCC = 3.0 V
0.9
1.5
2.6
NOTES: 1. The leakage current for the Comparator_A terminals is identical to Ilkg(Px.x) specification.
2. The input offset voltage can be cancelled by using the CAEX bit to invert the Comparator_A inputs on successive measurements.
The two successive measurements are then summed together.
25°C,
TA = 25
C,
Overdrive 10 mV, with filter: CAF = 1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
REFERENCE VOLTAGE
vs
FREE-AIR TEMPERATURE
REFERENCE VOLTAGE
vs
FREE-AIR TEMPERATURE
650
650
VCC = 2.2 V
V(RefVT) − Reference Voltage − mV
V(RefVT) − Reference Voltage − mV
VCC = 3 V
600
Typical
550
500
450
400
−45
−25
−5
15
35
55
75
600
Typical
550
500
450
400
−45
95
−25
−5
35
Figure 7
Figure 6
0 V VCC
0
15
CAF
1
CAON
Low Pass Filter
V+
V−
+
_
0
0
1
1
To Internal
Modules
CAOUT
Set CAIFG
Flag
τ ≈ 2 µs
Figure 8. Block Diagram of Comparator_A Module
VCAOUT
Overdrive
V−
400 mV
V+
t(response)
Figure 9. Overdrive Definition
24
55
TA − Free-Air Temperature − °C
TA − Free-Air Temperature − °C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
75
95
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
POR brownout, reset (see Notes 1 and 2)
PARAMETER
TEST CONDITIONS
td(BOR)
VCC(start)
MIN
dVCC/dt ≤ 3 V/s (see Figure 10)
V(B_IT−)
Vhys(B_IT−)
MAX
UNIT
2000
µs
0.7 × V(B_IT−)
dVCC/dt ≤ 3 V/s (see Figure 10, Figure 11, Figure 12)
dVCC/dt ≤ 3 V/s (see Figure 10)
Brownout
TYP
70
130
V
1.71
V
180
mV
Pulse length needed at RST/NMI pin to accepted reset internally,
2
µs
VCC = 2.2 V/3 V
NOTES: 1. The current consumption of the brownout module is already included in the ICC current consumption data. The voltage level V(B_IT−)
+ Vhys(B_IT−) is ≤ 1.8 V.
2. During power up, the CPU begins code execution following a period of td(BOR) after VCC = V(B_IT−) + Vhys(B_IT−). The default FLL+
settings must not be changed until VCC ≥ VCC(min). See the MSP430x4xx Family User’s Guide (SLAU056) for more information on
the brownout/SVS circuit.
t(reset)
VCC
Vhys(B_IT−)
V(B_IT−)
VCC(start)
1
0
td(BOR)
Figure 10. POR/Brownout Reset (BOR) vs Supply Voltage
VCC
2
VCC (min) − V
tpw
3V
V cc = 3 V
Typical Conditions
1.5
1
VCC(min)
0.5
0
0.001
1
1000
1 ns
tpw − Pulse Width − µs
1 ns
tpw − Pulse Width − µs
Figure 11. VCC(min) Level With a Square Voltage Drop to Generate a POR/Brownout Signal
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
VCC
VCC (min) − V
2
1.5
tpw
3V
V cc = 3 V
Typical Conditions
1
VCC(min)
0.5
0
0.001
tf = tr
1
1000
tf
tr
tpw − Pulse Width − µs
tpw − Pulse Width − µs
Figure 12. VCC(min) Level With a Triangle Voltage Drop to Generate a POR/Brownout Signal
SVS (supply voltage supervisor/monitor) (See Notes 1 and 2)
PARAMETER
TEST CONDITIONS
MIN
t(SVSR)
dVCC/dt > 30 V/ms (see Figure 13)
dVCC/dt ≤ 30 V/ms
5
td(SVSon)
tsettle
SVSon, switch from VLD=0 to VLD ≠ 0, VCC = 3 V
VLD ≠ 0‡
20
V(SVSstart)
VLD ≠ 0, VCC/dt ≤ 3 V/s (see Figure 13)
VLD = 1
VCC/dt ≤ 3 V/s (see Figure 13)
VLD = 2 .. 14
Vhys(B_IT−)
VCC/dt ≤ 3 V/s (see Figure 13), external voltage applied
on SVSIN
VCC/dt ≤ 3 V/s (see Figure 13)
V(SVS_IT−)
VCC/dt ≤ 3 V/s (see Figure 13), external voltage applied
on SVSIN
VLD = 15
70
NOM
MAX
UNIT
150
µs
2000
µs
150
µs
12
µs
1.55
1.7
V
120
155
mV
V(SVS_IT−)
x 0.004
V(SVS_IT−)
x 0.008
4.4
10.4
VLD = 1
1.8
1.9
2.05
VLD = 2
1.94
2.1
2.25
VLD = 3
2.05
2.2
2.37
VLD = 4
2.14
2.3
2.48
VLD = 5
2.24
2.4
2.6
VLD = 6
2.33
2.5
2.71
VLD = 7
2.46
2.65
2.86
VLD = 8
2.58
2.8
3
VLD = 9
2.69
2.9
3.13
VLD = 10
2.83
3.05
3.29
VLD = 11
2.94
3.2
VLD = 12
3.11
3.35
VLD = 13
3.24
VLD = 14
3.43
3.5
3.7†
3.42
3.61†
3.76†
VLD = 15
1.1
1.2
mV
V
3.99†
1.3
ICC(SVS)
VLD ≠ 0, VCC = 2.2 V/3 V
10
15
µA
(see Note 1)
† The recommended operating voltage range is limited to 3.6 V.
‡ tsettle is the settling time that the comparator o/p needs to have a stable level after VLD is switched VLD ≠ 0 to a different VLD value somewhere
between 2 and 15. The overdrive is assumed to be > 50 mV.
NOTES: 1. The current consumption of the SVS module is not included in the ICC current consumption data.
2. The SVS is not active at power up.
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Software Sets VLD>0:SVS is Active
VCC
V
(SVS_IT−)
V(SVSstart)
Vhys(SVS_IT−)
Vhys(B_IT−)
V(B_IT−)
VCC(start)
Brownout
Brownout
Region
Brownout
Region
1
0
td(BOR)
SVS out
td(BOR)
SVS Circuit is Active From VLD > to VCC < V(B_IT−)
1
0
td(SVSon)
Set POR
1
td(SVSR)
Undefined
0
Figure 13. SVS Reset (SVSR) vs Supply Voltage
VCC
3V
tpw
2
Rectangular Drop
VCC(min) − V
1.5
VCC(min)
Triangular Drop
1
1 ns
0.5
1 ns
VCC
3V
tpw
0
1
10
100
1000
tpw − Pulse Width − µs
VCC(min)
tf = tr
tf
tr
t − Pulse Width − µs
Figure 14. VCC(min) With a Square Voltage Drop and a Triangle Voltage Drop to Generate an SVS Signal
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
DCO
PARAMETER
f(DCOCLK)
TEST CONDITIONS
VCC
2.2 V/3 V
MIN
TYP
2.2 V
0.3
0.65
1.25
3V
0.3
0.7
1.3
2.2 V
2.5
5.6
10.5
3V
2.7
6.1
11.3
2.2 V
0.7
1.3
2.3
3V
0.8
1.5
2.5
2.2 V
5.7
10.8
18
3V
6.5
12.1
20
2.2 V
1.2
2
3
3V
1.3
2.2
3.5
2.2 V
9
15.5
25
3V
10.3
17.9
28.5
2.2 V
1.8
2.8
4.2
3V
2.1
3.4
5.2
2.2 V
13.5
21.5
33
3V
16
26.6
41
2.2 V
2.8
4.2
6.2
3V
4.2
6.3
9.2
2.2 V
21
32
46
3V
30
46
70
1 < TAP ≤ 20
1.06
TAP = 27
1.07
2.2 V
–0.2
–0.3
–0.4
3V
–0.2
–0.3
–0.4
0
5
15
N(DCO)=01E0h, FN_8=FN_4=FN_3=FN_2=0, D = 2, DCOPLUS= 0
f(DCO2)
FN_8=FN_4=FN_3=FN_2=0 , DCOPLUS = 1
f(DCO27)
FN_8=FN_4=FN_3=FN_2=0, DCOPLUS = 1, (see Note 1)
f(DCO2)
FN_8=FN_4=FN_3=0, FN_2=1; DCOPLUS = 1
f(DCO27)
FN_8=FN_4=FN_3=0, FN_2=1; DCOPLUS = 1, (see Note 1)
f(DCO2)
FN_8=FN_4=0, FN_3= 1, FN_2=x; DCOPLUS = 1
f(DCO27)
FN_8=FN_4=0, FN_3= 1, FN_2=x;, DCOPLUS = 1, (see Note 1)
f(DCO2)
FN_8=0, FN_4= 1, FN_3= FN_2=x; DCOPLUS = 1
f(DCO27)
FN_8=0, FN_4=1, FN_3= FN_2=x; DCOPLUS = 1, (see Note 1)
f(DCO2)
FN_8=1, FN_4=FN_3=FN_2=x; DCOPLUS = 1
f(DCO27)
FN_8=1,FN_4=FN_3=FN_2=x,DCOPLUS = 1, (see Note 1)
Sn
Step size between adjacent DCO taps:
Sn = fDCO(Tap n+1) / fDCO(Tap n), (see Figure 16 for taps 21 to 27)
Dt
Temperature drift, N(DCO) = 01E0h, FN_8=FN_4=FN_3=FN_2=0
D = 2, DCOPLUS = 0, (see Note 2)
DV
Drift with VCC variation, N(DCO) = 01E0h, FN_8=FN_4=FN_3=FN_2=0
D = 2, DCOPLUS = 0 (see Note 2)
MAX
1
UNIT
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
1.11
1.17
%/_C
%/V
NOTES: 1. Do not exceed the maximum system frequency.
2. This parameter is not production tested.
f
f
f
(DCO)
f
(DCO3V)
(DCO)
(DCO205C)
1.0
1.0
0
1.8
2.4
3.0
3.6
VCC − V
−40
−20
0
20
40
60
Figure 15. DCO Frequency vs Supply Voltage VCC and vs Ambient Temperature
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
85
TA − °C
SLAS383 − OCTOBER 2003
Sn - Stepsize Ratio between DCO Taps
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
1.17
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎ
Max
1.11
1.07
1.06
Min
1
20
27
DCO Tap
Figure 16. DCO Tap Step Size
f(DCO)
Legend
Tolerance at Tap 27
DCO Frequency
Adjusted by Bits
29 to 25 in SCFI1 {N{DCO}}
Tolerance at Tap 2
Overlapping DCO Ranges:
Uninterrupted Frequency Range
FN_2=0
FN_3=0
FN_4=0
FN_8=0
FN_2=1
FN_3=0
FN_4=0
FN_8=0
FN_2=x
FN_3=1
FN_4=0
FN_8=0
FN_2=x
FN_3=x
FN_4=1
FN_8=0
FN_2=x
FN_3=x
FN_4=x
FN_8=1
Figure 17. Five Overlapping DCO Ranges Controlled by FN_x Bits
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
29
SLAS383 − OCTOBER 2003
crystal oscillator, LFXT1 oscillator (see Notes 1 and 2)
PARAMETER
CXIN
CXOUT
VIL
VIH
Integrated load capacitance
Integrated load capacitance
Input levels at XIN
TEST CONDITIONS
OSCCAPx = 0h
VCC
2.2 V/3 V
OSCCAPx = 1h
2.2 V/3 V
10
OSCCAPx = 2h
2.2 V/3 V
14
OSCCAPx = 3h
2.2 V/3 V
18
OSCCAPx = 0h
2.2 V/3 V
0
OSCCAPx = 1h
2.2 V/3 V
10
OSCCAPx = 2h
2.2 V/3 V
14
OSCCAPx = 3h
2.2 V/3 V
see Note 3
2.2 V/3 V
MIN
TYP
MAX
UNIT
0
pF
pF
18
VSS
0.8×VCC
0.2×VCC
VCC
V
NOTES: 1. The parasitic capacitance from the package and board may be estimated to be 2pF. The effective load capacitor for the crystal is
(CXIN x CXOUT) / (CXIN + CXOUT). It is independent of XTS_FLL.
2. To improve EMI on the low-power LFXT1 oscillator, particularly in the LF mode (32 kHz), the following guidelines must be
observe:
• Keep as short a trace as possible between the ’xW42x and the crystal.
• Design a good ground plane around oscillator pins.
• Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
• Avoid running PCB traces underneath or adjacent to XIN an XOUT pins.
• Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
• If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
• Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation.
This signal is no longer required for the serial programming adapter.
3. Applies only when using an external logic-level clock source. XTS_FLL must be set. Not applicable when using a crystal or resonator.
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Scan IF, port drive, port timing
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VOL(SIFCHx)
Voltage drop due to
excitation transistor’s
on−resistance.
(see Figure 18)
I(SIFCHx) = 2.0 mA, SIFTEN = 1
3V
0.3
V
VOH(SIFCHx)
(see Note 1)
Voltage drop due to
damping transistor’s
on−resistance.
(see Figure 18)
I(SIFCHx) = −200 µA, SIFTEN = 1
3V
0.1
V
0
0.1
V
3V
−50
50
nA
2.2 V/3 V
−20
20
ns
VOL(SIFCOM)
I(SIFCOM) = 3 mA, SIFSH = 1
V(SIFCHx) = 0 V to AVCC, port function
disabled, SIFSH = 1
ISIFCHx(tri-state)
∆tdSIFCH :
twEx(tsm)−twSIFCH
(see Note 2 and
Figure 18)
Change of pulse width
of internal signal
SIFEX(tsm) to pulse
width at pin SIFCHx
I(SIFCHx) = 3 mA,
tEx(SIFCHx) = 500 ns ±20%
2.2 V/3 V
NOTES: 4. SIFCOM=1.5V , supplied externally. (See Figure 19).
5. Not production tested.
tEx(SIFCHx)
SIFEX(tsm)
P6.x/SIFCH.x
tSIFCH(x)
Figure 18. P6.x/SIFCHx timing, SIFCHx function selected
SIFCOM
VOH(SIFCHx)
Damping
Transistor
I(SIFCHx)
P6.x/SIFCH.x
VOL(SIFCHx)
Excitation
Transistor
Figure 19. Voltage drop due to on-resistance
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
31
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Scan IF, sample capacitor/Ri timing (See Note 1)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
CSHC(SIFCHx)
Sample capacitance
at SIFCHx pin
SIFEx(tsm) = 1, SIFSH = 1
2.2 V/3 V
5
7
pF
Ri(SIFCHx)
Serial input resistance
at the SIFCHx pin
SIFEx(tsm) = 1, SIFSH = 1
2.2 V/3 V
1.5
3
kΩ
tHold
(See Notes 6 and 2)
Maximum hold time
∆Vsample < 3 mV
µs
62
NOTES: 6. Values are not production tested.
7. The sampled voltage at the sample capacitance varies less than 3 mV (∆Vsample) during the hold time tHold. If the voltage is sampled
after tHold, the sampled voltage may be any other value.
8. The minimum sampling time (7.6 x tau for 1/2 LSB accuracy) with maximum CSHC(SIFCHx) and Ri(SIFCHx) and Ri(source) is
tsample(min) ~ 7.6 x CSHC(SIFCHx) x (Ri(SIFCHx) + Ri(source))
with Ri(source) estimated at 3 kΩ, tsample(min) = 319 ns.
Scan IF, VCC/2 generator
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
AVCC
Analog supply
voltage
AVCC = DVCC (connected together)
AVSS = DVSS (connected together)
AICC
Scan IF VCC/2
generator operating
supply current into
AVCC terminal
CL at SIFCOM pin = 470 nF ±20%,
frefresh(SIFCOM) =32768 Hz
frefresh(SIFCOM)
VCC/2 refresh
frequency
Source clock = ACLK
V(SIFCOM)
Output voltage at
pin SIFCOM
CL at SIFCOM pin = 470 nF ±20%,
I_Load = 1µA
SIFCOM source
current (see Note 2
and Figure 20)
2.2 V
−500
Isource(SIFCOM)
3V
−900
SIFCOM sink
current (see Note 2
and Figure 20)
2.2 V
150
Isink(SIFCOM)
3V
180
trecovery(SIFCOM)
Time to recover
from Voltage Drop
on Load
ILoad1 = ILOAD3 = 0 mA
ILoad2 = 3 mA, tload(on) = 500nS,
CL at SIFCOM pin = 470 nF ±20%
ton(SIFCOM)
Time to reach 98%
after VCC/2 is
switched on
CL at SIFCOM pin = 470 nF ±20%
frefresh(SIFCOM) = 32768 Hz
tVccSettle(SIFCOM)
(See Note 1)
Settling time to
±VCC/512 (2 LSB)
after AVCC voltage
change
MAX
2.2
UNIT
3.6
2.2 V
250
350
3V
370
450
V
nA
2.2 V/3 V
30
32.768
AVCC/2 −
.05
AVCC/2
kHz
AVCC/2 +
.05
V
µA
A
nA
2.2 V/3 V
30
µss
6
ms
2.2 V/3 V
1.7
SIFEN =1, SIFVCC2 =1, SIFSH =0,
AVCC = AVCC −100 mV
frefresh(SIFCOM) = 32768 Hz
2.2 V/3 V
AVCC = AVCC + 100mV
frefresh(SIFCOM) = 32768 Hz
2.2 V/3 V
80
ms
3
NOTES: 9. The settling time after an AVCC voltage change is the time to for the voltage at pin SIFCOM to settle to AVCC/2 ± 2LSB.
10. The sink and source currents are a function of the voltage at the pin SIFCOM. The maximum currents are reached if SIFCOM is
shorted to GND or VCC. Due to the topology of the output section (refer to Figure 20) the VCC/2 generator can source relatively large
currents but can sink only small currents.
32
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
VCC
VCC/2
ISource(SIFCOM)
SIFCOM
ISink(SIFCOM)
Figure 20. P6.x/SIFCHx timing, SIFCHx function selected
Scan IF, 10-bit DAC (See Note 11)
PARAMETER
TEST CONDITIONS
AVCC
Analog supply voltage
AVCC = DVCC (connected together)
AVSS = DVSS (connected together)
AICC
Scan IF 10-bit DAC
operating supply
current into AVCC
terminal
CL at SIFCOM pin = 470 nF ±20%,
frefresh(SIFCOM) = 32768 Hz
VCC
MIN
2.2
MAX
3.6
2.2 V
23
45
3V
33
60
UNIT
V
A
µA
Resolution
10
INL
RL = 1000 MΩ,
CL = 20 pF
2.2 V/3 V
DNL
RL = 1000 MΩ,
CL = 20 pF
EZS
EG
RO
Output resistance
ton(SIFDAC)
On time after AVCC of
SIFDAC is switched on
tSettle(SIFDAC)
TYP
±5
LSB
2.2 V/3 V
±1
LSB
Zero Scale Error
2.2 V/3 V
±10
mV
Gain Error
2.2 V/3 V
Settling time
±2
bit
25
0.6
%
50
kΩ
V+SIFCA − VSIFDAC = ±6 mV
2.2 V/3 V
2.0
µs
SIFDAC code = 1C0h → 240h
VSIFDAC(240h) − V+SIFCA = +6 mV
2.2 V/3 V
2.0
µs
2.0
µs
SIFDAC code = 240h → 1C0h,
2.2 V/3 V
VSIFDAC(1C0h) − V+SIFCA = −6 mV
NOTES: 11. The SIFDAC operates from AVCC and SIFVSS. All parameters are based on these references.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
33
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Scan IF, Comparator
PARAMETER
AVCC
Analog supply voltage
TEST CONDITIONS
VCC
AVCC = DVCC (connected together)
AVSS = DVSS (connected together)
MIN
TYP
2.2
MAX
UNIT
3.6
V
VIC
Scan IF comparator
operating supply current
into AVCC terminal
Common Mode Input
Voltage Range
VOffset
Input Offset Voltage
2.2 V/3 V
dVOffset/dT
Temperature coefficient of
VOffset
2.2 V/3 V
10
µV/_C
dVOffset/dVCC
VOffset supply voltage
(VCC) sensitivity
2.2 V/3 V
0.3
mV/V
Vhys
Input Voltage Hysteresis
V+terminal = V−terminal = 0.5 x VCC
ton(SIFCA)
On time after SIFCA is
switched on
V+SIFCA − VSIFDAC = +6 mV
V+SIFCA = 0.5 x AVCC
2.2 V/3 V
2.0
us
tSettle(SIFCA)
Settle time
V+SIFCA − VSIFDAC= −12 mV → 6
mV
V+SIFCA = 0.5 x AVCC
2.2 V/3 V
2.0
us
AICC
(see Note 1)
2.2 V
25
35
3V
35
50
2.2 V/3 V
µA
A
AVCC
− 0.5
0.9
±30
2.2V
0
5.0
3.0V
0
6.0
V
mV
mV
NOTES: 12. The comparator output is reliable when at least one of the input signals is within the common mode input voltage range.
Scan IF, SIFCLK Oscillator
PARAMETER
TEST CONDITIONS
AVCC
Analog supply voltage
AICC
Scan IF oscillator
operating supply current
into AVCC terminal
fSIFCLKG = 0
Scan IF oscillator at
minimum setting
TA=25ºC, SIFCLKFQ=0000
fSIFCLKG = 8
Scan IF oscillator at
nominal setting
TA=25ºC, SIFCLKFQ=0000
fSIFCLKG = 15
Scan IF oscillator at
maximum setting
TA=25ºC, SIFCLKFQ=0000
ton(SIFCLKG)
Settling time to full
operation after VCC is
switched on
S(SIFCLK)
Frequency Change per ±1
SIFCLKFQ(SIFCTL5) step
Dt
DV
34
VCC
AVCC = DVCC (connected together)
AVSS = DVSS (connected together)
MIN
TYP
2.2
MAX
3.6
2.2 V
75
3V
90
SIFNOM = 0
1.8
3.2
SIFNOM = 1
0.45
0.8
SIFNOM = 0
4
SIFNOM = 1
1
UNIT
V
µA
A
MHz
SIFNOM = 0
4.48
6.8
SIFNOM = 1
1.12
1.7
2.2 V/3 V
150
500
ns
S(SIFCLK) = f(SIFCLKFQ + 1) /
f(SIFCLKFQ)
2.2 V/3 V
1.01
1.18
Hz/Hz
Temperature Coefficient
SIFCLKFQ(SIFCTL5) = 8
2.2 V/3 V
0.35
%/_C
Frequency vs. supply
voltage VCC variation
SIFCLKFQ(SIFCTL5) = 8
2.2 V/3 V
2
%/V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1.05
SLAS383 − OCTOBER 2003
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Flash Memory
TEST
CONDITIONS
PARAMETER
VCC(PGM/
ERASE)
VCC
MIN
NOM
MAX
UNIT
Program and Erase supply voltage
2.7
3.6
V
fFTG
IPGM
Flash Timing Generator frequency
257
476
kHz
Supply current from DVCC during program
2.7 V/ 3.6 V
3
5
mA
IERASE
tCPT
Supply current from DVCC during erase
2.7 V/ 3.6 V
3
5
mA
Cumulative program time
see Note 1
2.7 V/ 3.6 V
4
ms
tCMErase
Cumulative mass erase time
see Note 2
2.7 V/ 3.6 V
Program/Erase endurance
TJ = 25°C
200
104
ms
105
tRetention
Data retention duration
tWord
tBlock, 0
Word or byte program time
Block program time for 1st byte or word
tBlock, 1-63
tBlock, End
Block program time for each additional byte or word
tMass Erase
tSeg Erase
Mass erase time
5297
Segment erase time
4819
Block program end-sequence wait time
cycles
100
years
35
30
21
see Note 3
tFTG
6
NOTES: 13. The cumulative program time must not be exceeded during a block-write operation. This parameter is only relevant if the block write
feature is used.
14. The mass erase duration generated by the flash timing generator is at least 11.1ms ( = 5297x1/fFTG,max = 5297x1/476kHz). To
achieve the required cumulative mass erase time the Flash Controller’s mass erase operation can be repeated until this time is met.
(A worst case minimum of 19 cycles are required).
15. These values are hardwired into the Flash Controller’s state machine (tFTG = 1/fFTG).
JTAG Interface, F-Device
TEST
CONDITIONS
PARAMETER
fTCK
TCK input frequency
see Note 1
RInternal
Internal pull-up resistance on TMS, TCK, TDI/TCLK
see Note 2
VCC
MIN
2.2 V
0
NOM
MAX
UNIT
5
MHz
3V
0
10
MHz
2.2 V/ 3 V
25
60
90
kΩ
MIN
NOM
MAX
NOTES: 16. fTCK may be restricted to meet the timing requirements of the module selected.
17. TMS, TDI/TCLK, and TCK pull-up resistors are implemented in all versions.
JTAG Fuse, F-Device (see Note 1)
TEST
CONDITIONS
PARAMETER
VCC(FB)
VFB
Supply voltage during fuse-blow condition
IFB
tFB
Supply current into TDI/TCLK during fuse blow
TA = 25°C
Voltage level on TDI/TCLK for fuse-blow
VCC
2.5
6
Time to blow fuse
UNIT
V
7
V
100
mA
1
ms
NOTES: 18. Once the fuse is blown, no further access to the MSP430 JTAG/Test and emulation features is possible. The JTAG block is switched
to bypass mode.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
35
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
Port P1, P1.0 to P1.5, input/output with Schmitt-trigger
Pad Logic
CAPD.x
P1SEL.x
0: Input
1: Output
0
P1DIR.x
Direction Control
From Module
P1OUT.x
1
0
1
Module X OUT
Bus
keeper
P1.0/TA0.0
P1.1/TA0.0/MCLK
P1.2/TA0.1
P1.3/TA1.0/SVSOUT
P1.4/TA1.0
P1.5/TA0CLK/ACLK
P1IN.x
EN
D
Module X IN
P1IE.x
P1IRQ.x
P1IFG.x
Q
EN
Interrupt
Edge
Select
Set
P1IES.x
P1SEL.x
NOTE: 0 ≤ x ≤ 5.
Port Function is Active if CAPD.x = 0
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
PnIE.x
PnIFG.x
PnIES.x
P1SEL.0
P1DIR.0
P1DIR.0
P1OUT.0
Out0 Sig.†
P1IN.0
CCI0A†
P1IE.0
P1IFG.0
P1IES.0
P1SEL.1
P1DIR.1
P1DIR.1
P1OUT.1
MCLK
P1IN.1
CCI0B†
P1IE.1
P1IFG.1
P1IES.1
P1SEL.2
P1DIR.2
P1DIR.2
P1OUT.2
Out1 Sig.†
P1IN.2
CCI1A†
P1IE.2
P1IFG.2
P1IES.2
P1SEL.3
P1DIR.3
P1DIR.3
P1OUT.3
SVSOUT
P1IN.3
CCI0B‡
P1IE.3
P1IFG.3
P1IES.3
P1SEL.4
P1DIR.4
P1DIR.4
P1OUT.4
Out0 Sig.‡
P1IN.4
CCI0A‡
P1IE.4
P1IFG.4
P1IES.4
P1SEL.5
P1DIR.5
P1DIR.5
P1OUT.5
ACLK
P1IN.5
T0ACLK†
P1IE.5
P1IFG.5
P1IES.5
† Timer0_A
‡ Timer1_A
36
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
Port P1, P1.6, P1.7 input/output with Schmitt-trigger
Pad Logic
Note: Port Function Is Active if CAPD.6 = 0
CAPD.6
P1SEL.6
0: Input
1: Output
0
P1DIR.6
1
P1DIR.6
P1.6/
CA0
0
P1OUT.6
1
DVSS
Bus
Keeper
P1IN.6
EN
D
unused
P1IE.7
P1IRQ.07
EN
Interrupt
Edge
Select
Q
P1IFG.7
Set
P1IES.x
P1SEL.x
Comparator_A
P2CA
AVcc
CAREF
CAEX
CA0
CAF
CCI1B
+
to Timer_Ax
−
CA1
2
Reference Block
CAREF
Pad Logic
Note: Port Function Is Active if CAPD.7 = 0
CAPD.7
P1SEL.7
0: Input
1: Output
0
P1DIR.7
1
P1.7/
CA1
P1DIR.7
0
P1OUT.7
1
DVSS
Bus
Keeper
P1IN.7
EN
unused
D
P1IE.7
P1IRQ.07
EN
Q
P1IFG.7
Set
Interrupt
Edge
Select
P1IES.7
P1SEL.7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
37
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P2, P2.0 to P2.7, input/output with Schmitt-trigger
P2.0, P2.1
LCDM.5
LCDM.6
P2.2 to P2.5
LCDM.7
P2.6, P2.7
0: Port Active
1: Segment xx
Function Active
Pad Logic
Segment xx
P2SEL.x
0: Input
1: Output
0
P2DIR.x
Direction Control
From Module
P2OUT.x
1
0
P2.x
1
Module X OUT
Bus
keeper
P2.0/TA0.2
P2.1/TA1.1
P2.2/TA1.2/S23
P2.3/TA1.3/S22
P2.4/TA1.4/S21
P2.5/TA1CLK/S20
P2.6/CAOUT/S19
P2.7/SIFCLKG/S18
P2IN.x
EN
Module X IN
D
P2IE.x
P2IRQ.x
P2IFG.x
Q
EN
Set
NOTE: 0 ≤ x ≤ 7
Interrupt
Edge
Select
P2IES.x
P2SEL.x
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
PnIE.x
PnIFG.x
PnIES.x
P2SEL.0
P2DIR.0
P2DIR.0
P2OUT.0
Out2 Sig.†
P2IN.0
CCI2A†
P2IE.0
P2IFG.0
P2IES.0
P2SEL.1
P2DIR.1
P2DIR.1
P2OUT.1
Out1 Sig.‡
P2IN.1
CCI1A‡
P2IE.1
P2IFG.1
P2IES.1
P2SEL.2
P2DIR.2
P2DIR.2
P2OUT.2
Out2 Sig.‡
P2IN.2
CCI2A‡
P2IE.2
P2IFG.2
P2IES.2
P2SEL.3
P2DIR.3
P2DIR.3
P2OUT.3
Out3 Sig.‡
P2IN.3
CCI3A‡
P2IE.3
P2IFG.3
P2IES.3
P2SEL.4
P2DIR.4
P2DIR.4
P2OUT.4
Out4 Sig.‡
P2IN.4
CCI4A‡
P2IE.4
P2IFG.4
P2IES.4
P2SEL.5
P2DIR.5
P2DIR.5
P2OUT.5
DVSS
P2IN.5
TA1CLK1‡
P2IE.5
P2IFG.5
P2IES.5
P2SEL.6
P2DIR.6
P2DIR.6
P2OUT.6
CAOUT
P2IN.6
Unused
P2IE.6
P2IFG.6
P2IES.6
P2SEL.7
P2DIR.7
P2DIR.7
P2OUT.7
SIFCLKG§
P2IN.7
Unused
P2IE.7
P2IFG.7
P2IES.7
†Timer0_A
‡Timer1_A
§Scan IF
38
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P3, P3.0, P3.7, input/output with Schmitt-trigger
LCDM.5
LCDM.6
LCDM.7
P3.2 to P3.7
P3.0, P3.1
0: Port Active
1: Segment xx
Function Active
Pad Logic
Segment xx
P3SEL.x
0: Input
1: Output
0
P3DIR.x
Direction Control
From Module
P3OUT.x
1
0
1
Module X OUT
P3.x
Bus
keeper
P3.0/S17
P3.1/S16
P3.2/S15
P3.3/S14
P3.4/S13
P3.5/S12
P3.6/S11
P3.7/S10
P3IN.x
EN
D
Module X IN
NOTE: 0 ≤ x ≤ 7
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
P3SEL.0
P3DIR.0
P3DIR.0
P3OUT.0
DVSS
P3IN.0
Unused
P3SEL.1
P3DIR.1
P3DIR.1
P3OUT.1
DVSS
P3IN.1
Unused
P3SEL.2
P3DIR.2
P3DIR.2
P3OUT.2
DVSS
P3IN.2
Unused
P3SEL.3
P3DIR.3
P3DIR.3
P3OUT.3
DVSS
P3IN.3
Unused
P3SEL.4
P3DIR.4
P3DIR.4
P3OUT.4
DVSS
P3IN.4
Unused
P3SEL.5
P3DIR.5
P3DIR.5
P3OUT.5
DVSS
P3IN.5
Unused
P3SEL.6
P3DIR.6
P3DIR.6
P3OUT.6
DVSS
P3IN.6
Unused
P3SEL.7
P3DIR.7
P3DIR.7
P3OUT.7
DVSS
P3IN.7
Unused
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
39
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P4, P4.0 to P4.7, input/output with Schmitt-trigger
LCDM.5
LCDM.6
LCDM.7
0: Port Active
1: Segment xx
Function Active
Pad Logic
Segment xx
P4SEL.x
0: Input
1: Output
0
P4DIR.x
Direction Control
From Module
P4OUT.x
1
0
1
Module X OUT
P4.x
Bus
keeper
P4.0/S9
P4.1/S8
P4.2/S7
P4.3/S6
P4.4/S5
P4.5/S4
P4.6/S3
P4.7/S2
P4IN.x
EN
D
Module X IN
NOTE: 0 ≤ x ≤ 7
40
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
P4SEL.0
P4DIR.0
P4DIR.0
P4OUT.0
DVSS
P4IN.0
Unused
P4SEL.1
P4DIR.1
P4DIR.1
P4OUT.1
DVSS
P4IN.1
Unused
P4SEL.2
P4DIR.2
P4DIR.2
P4OUT.2
DVSS
P4IN.2
Unused
P4SEL.3
P4DIR.3
P4DIR.3
P4OUT.3
DVSS
P4IN.3
Unused
P4SEL.4
P4DIR.4
P4DIR.4
P4OUT.4
DVSS
P4IN.4
Unused
P4SEL.5
P4DIR.5
P4DIR.5
P4OUT.5
DVSS
P4IN.5
Unused
P4SEL.6
P4DIR.6
P4DIR.6
P4OUT.6
DVSS
P4IN.6
Unused
P4SEL.7
P4DIR.7
P4DIR.7
P4OUT.7
DVSS
P4IN.7
Unused
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P5, P5.0, P5.1, input/output with Schmitt-trigger
LCDM.5
LCDM.6
LCDM.7
0: Port Active
1: Segment
Function Active
Pad Logic
Segment xx or
COMx or Rxx
P5SEL.x
0: Input
1: Output
0
P5DIR.x
Direction Control
From Module
P5OUT.x
1
0
1
Module X OUT
P5.x
Bus
keeper
P5.0/S1
P5.1/S0
P5IN.x
EN
D
Module X IN
NOTE: x = 0, 1
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
Segment
P5SEL.0
P5DIR.0
P5DIR.0
P5OUT.0
DVSS
P5IN.0
Unused
S1
P5SEL.1
P5DIR.1
P5DIR.1
P5OUT.1
DVSS
P5IN.1
Unused
S0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
41
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P5, P5.2, P5.4, input/output with Schmitt-trigger
0: Port Active
1: COMx Function
Active
Pad Logic
COMx
P5SEL.x
0: Input
1: Output
0
P5DIR.x
Direction Control
From Module
P5OUT.x
1
0
1
Module X OUT
P5.x
Bus
keeper
P5.2/COM1
P5.3/COM2
P5.4/COM3
P5IN.x
EN
D
Module X IN
NOTE: 2 ≤ x ≤ 4
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
COMx
P5SEL.2
P5DIR.2
P5DIR.2
P5OUT.2
DVSS
P5IN.2
Unused
COM1
P5SEL.3
P5DIR.3
P5DIR.3
P5OUT.3
DVSS
P5IN.3
Unused
COM2
P5SEL.4
P5DIR.4
P5DIR.4
P5OUT.4
DVSS
P5IN.4
Unused
COM3
NOTE:
The direction control bits P5SEL.2, P5SEL.3, and P5SEL.4 are used to distinguish between port
and common functions. Note that a 4MUX LCD requires all common signals COM3 to COM0, a
3MUX LCD requires COM2 to COM0, 2MUX LCD requires COM1 to COM0, and a static LCD
requires only COM0.
42
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P5, P5.5 to P5.7, input/output with Schmitt-trigger
0: Port Active
1: Rxx Function
Active
Pad Logic
Rxx
P5SEL.x
0: Input
1: Output
0
P5DIR.x
Direction Control
From Module
P5OUT.x
1
0
1
Module X OUT
P5.x
Bus
keeper
P5.5/R13
P5.6/R23
P5.7/R33
P5IN.x
EN
D
Module X IN
NOTE: 5 ≤ x ≤ 7
PnSEL.x
PnDIR.x
Direction
Control
From Module
PnOUT.x
Module X
OUT
PnIN.x
Module X IN
Rxx
P5SEL.5
P5DIR.5
P5DIR.5
P5OUT.5
DVSS
P5IN.5
Unused
R13
P5SEL.6
P5DIR.6
P5DIR.6
P5OUT.6
DVSS
P5IN.6
Unused
R23
P5SEL.7
P5DIR.7
P5DIR.7
P5OUT.7
DVSS
P5IN.7
Unused
R33
NOTE:
The direction control bits P5SEL.5, P5SEL.6, and P5SEL.7 are used to distinguish between port
and LCD analog level functions. Note that 4MUX and 3MUX LCDs require all Rxx signals R33 to
R03, a 2MUX LCD requires R33, R13, and R03, and a static LCD requires only R33 and R03.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
43
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P6, P6.0, P6.1, P6.2, P6.4, P6.5, input/output with Schmitt-trigger
P6SEL.x
0
P6DIR.x
Direction Control
From Module
1
0: Input
1: Output
Pad Logic
0
P6OUT.x
Module X OUT
P6.X
1
P6.0/SIFCH0
P6.1/SIFCH1
P6.2/SIFCH2
P6.4/SIFCI0
P6.5/SIFCI1
Bus Keeper
P6IN.x
EN
Module X IN
D
To/From Scan I/F
P6SEL.x must be set if the corresponding pins are used by the Scan IF.
x: Bit Identifier = 0, 1, 2, 4, or 5
NOTE: Analog signals applied to digital gates can cause current flow from the positive to the negative terminal. The throughput current flows if
the analog signal is in the range of transitions 0→1 or 1→0. The value of the throughput current depends on the driving capability of the
gate. For MSP430, it is approximately 100 µA.
Use P6SEL.x=1 to prevent throughput current. P6SEL.x should be set, if an analog signal is applied to the pin.
PnSEL.x
PnDIR.x
Dir. Control
From Module
PnOUT.x
Module X OUT
PnIN.x
Module X IN
P6Sel.0
P6DIR.0
P6DIR.0
P6OUT.0
DVSS
P6IN.0
unused
P6Sel.1
P6DIR.1
P6DIR.1
P6OUT.1
DVSS
P6IN.1
unused
P6Sel.2
P6DIR.2
P6DIR.2
P6OUT.2
DVSS
P6IN.2
unused
P6Sel.4
P6DIR.4
P6DIR.4
P6OUT.4
DVSS
P6IN.4
unused
P6Sel.5
P6DIR.5
P6DIR.5
P6OUT.5
DVSS
P6IN.5
unused
NOTE: The signal at pins P6.x/SIFCHx and P6.x/SIFCIx are shared by Port P6 and the San IF module. P6SEL.x must be set if the corresponding
pins are used by the Scan IF.
44
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P6, P6.3 input/output with Schmitt-trigger
P6SEL.3
0
P6DIR.3
0: Input
1: Output
1
Pad Logic
0
P6OUT.x
SIFCAOUT
P6.3/SIFCH3/SIFCAOUT
1
Bus Keeper
P6IN.3
EN
Module X IN
D
To/From Scan I/F
P6SEL.x must be set if the corresponding pins are used by the Scan IF.
NOTE: Analog signals applied to digital gates can cause current flow from the positive to the negative terminal. The throughput current flows if
the analog signal is in the range of transitions 0→1 or 1→0. The value of the throughput current depends on the driving capability of the
gate. For MSP430, it is approximately 100 µA.
Use P6SEL.x=1 to prevent throughput current. P6SEL.x should be set, if an analog signal is applied to the pin.
P6SEL.3
P6DIR.3
Port Function
0
0
P6.3 Input
0
1
P6.3 Output
1
0
SIFCH3 (Scan IF channel 3 excitation output and comparator input)
1
1
SIFCAOUT (Comparator output)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
45
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P6, P6.6 input/output with Schmitt-trigger
P6SEL.6
0
P6DIR.6
0: Input
1: Output
1
Pad Logic
0
P6OUT.6
DVss
P6.6/SIFCI2/DACOUT
1
Bus Keeper
P6IN.6
EN
Module X IN
D
1
From Scan I/F DAC
To Scan I/F comparator input mux
P6SEL.x must be set if the corresponding pins are used by the Scan IF.
NOTE: Analog signals applied to digital gates can cause current flow from the positive to the negative terminal. The throughput current flows if
the analog signal is in the range of transitions 0→1 or 1→0. The value of the throughput current depends on the driving capability of the
gate. For MSP430, it is approximately 100 µA.
Use P6SEL.x=1 to prevent throughput current. P6SEL.x should be set, if an analog signal is applied to the pin.
46
P6SEL.6
P6DIR.6
0
0
P6.6 Input
0
1
P6.6 Output
1
0
SIFCI2 (Scan IF channel 2 comparator input)
1
1
SIFDAOUT (Scan IF DAC output)
Port Function
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
port P6, P6.7 input/output with Schmitt-trigger
SVS VLDx=15
P6SEL.7
P6DIR.7
0
1
0: Input
1: Output
Pad Logic
0
P6OUT.7
DVss
P6.6/SIFCI3/SVSIN
1
Bus Keeper
P6IN.7
EN
Module X IN
D
SVS VLDx=15
1
To SVS
To Scan I/F comparator (+) terminal
P6SEL.x must be set if the corresponding pins are used by the Scan IF.
NOTE: Analog signals applied to digital gates can cause current flow from the positive to the negative terminal. The throughput current flows if
the analog signal is in the range of transitions 0→1 or 1→0. The value of the throughput current depends on the driving capability of the
gate. For MSP430, it is approximately 100 µA.
Use P6SEL.x=1 to prevent throughput current. P6SEL.x should be set, if an analog signal is applied to the pin.
SVS VLDx = 15
P6SEL.7
P6DIR.7
0
0
0
P6.7 Input
0
0
1
P6.7 Output
0
1
X
SIFCI3 (Scan IF channel 3 comparator input)
1
X
X
SVSIN
POST OFFICE BOX 655303
Port Function
• DALLAS, TEXAS 75265
47
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
JTAG pins TMS, TCK, TDI/TCLK, TDO/TDI, input/output with Schmitt-trigger or output
TDO
Controlled by JTAG
Controlled by JTAG
TDO/TDI
JTAG
Controlled
by JTAG
DVCC
TDI
Burn and Test
Fuse
TDI/TCLK
Test
and
Emulation
DVCC
TMS
Module
TMS
DVCC
TCK
TCK
RST/NMI
Tau ~ 50 ns
Brownout
TCK
48
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
G
D
U
S
G
D
U
S
SLAS383 − OCTOBER 2003
APPLICATION INFORMATION
JTAG fuse check mode
MSP430 devices that have the fuse on the TDI/TCLK terminal have a fuse check mode that tests the continuity
of the fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF , of 1.8 mA at 3 V can flow from the TDI/TCLK pin to ground if the fuse is not burned. Care must be
taken to avoid accidentally activating the fuse check mode and increasing overall system power consumption.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if the
TMS is being held low during power up. The second positive edge on the TMS pin deactivates the fuse check
mode. After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the
fuse check mode has the potential to be activated.
The fuse check current only flows when the fuse check mode is active and the TMS pin is in a low state (see
Figure 21). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
The JTAG pins are terminated internally, and therefore do not require external termination.
Time TMS Goes Low After POR
TMS
ITDI/TCLK
ITF
Figure 21. Fuse Check Mode Current, MSP430FW42x
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
49
MECHANICAL DATA
MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996
PM (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
0,08 M
33
48
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040152 / C 11/96
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Falls within JEDEC MS-026
May also be thermally enhanced plastic with leads connected to the die pads.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Amplifiers
Applications
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated