FREESCALE DSPB56374AFC

Freescale Semiconductor
Data Sheet: Technical Data
DSP56374
Rev. 4.2, 1/2007
DSP56374 Data Sheet
1
Overview
The DSP56374 is a high-density CMOS device with
3.3 V inputs and outputs.
NOTE
This document contains information on a
new product. Specifications and
information herein are subject to change
without notice.
For software or simulation models (for
example, IBIS files), contact sales or go
to www.freescale.com.
The DSP56374 supports digital audio applications
requiring sound field processing, acoustic equalization,
and other digital audio algorithms. The DSP56374 uses
the high performance, single-clock-per-cycle DSP56300
core family of programmable CMOS digital signal
processors (DSPs) combined with the audio signal
processing capability of the Freescale Semiconductor,
Inc. Symphony™ DSP family, as shown in Figure 1.
Significant architectural enhancements include a barrel
shifter, 24-bit addressing, and direct memory access
Table of Contents
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Signal Groupings . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . 25
Power Requirements . . . . . . . . . . . . . . . . . . . . . 26
Thermal Characteristics . . . . . . . . . . . . . . . . . . . 27
DC Electrical Characteristics . . . . . . . . . . . . . . . 28
AC Electrical Characteristics. . . . . . . . . . . . . . . . 29
Internal Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . 29
External Clock Operation . . . . . . . . . . . . . . . . . . 29
Reset, Stop, Mode Select, and Interrupt Timing . 32
Serial Host Interface SPI Protocol Timing. . . . . . 35
Serial Host Interface (SHI) I2C Protocol Timing . 41
Programming the Serial Clock . . . . . . . . . . . . . . 43
Enhanced Serial Audio Interface Timing. . . . . . . 44
Timer Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
GPIO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
JTAG Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Watchdog Timer Timing . . . . . . . . . . . . . . . . . . . 53
© Freescale Semiconductor, Inc., 2004, 2005, 2006, 2007. All rights reserved.
Overview
(DMA). The DSP56374 offers 150 million instructions per second (MIPS) using an internal 150 MHz
clock.
Data Sheet Conventions
This data sheet uses the following conventions:
OVERBAR
“asserted”
Used to indicate a signal that is active when pulled low (For example,
the RESET pin is active when low.)
Means that a high true (active high) signal is high or that a low true
(active low) signal is low
“deasserted” Means that a high true (active high) signal is low or that a low true
(active low) signal is high
Examples:
Signal/
Symbol
Logic State
Signal State
Voltage*
PIN
True
Asserted
VIL / VOL
PIN
False
Deasserted
VIH / VOH
PIN
True
Asserted
VIH / VOH
PIN
False
Deasserted
VIL / VOL
Note: *Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
DSP56374 Data Sheet, Rev. 4.2
2
Freescale Semiconductor
Features
15*
5
3
12*
12
Memory Expansion Area
ESAI_1
Interface
Triple
Timer
Watch
dog
Timer
Program
RAM
6k × 24
X Data
RAM
6k × 24
Y Data
RAM
6k × 24
ROM
20k × 24
ROM
4k × 24
ROM
4k × 24
Address
Generation
Unit
Six Channel
DMA Unit
YAB
XAB
PAB
DAB
YM_EB
Expansion Area
XM_EB
Peripheral
PIO_EB
ESAI
Interface
PM_EB
GPIO
SHI
Interface
24-Bit
Bootstrap
ROM
DSP56300
Core
DDB
YDB
XDB
PDB
GDB
Internal
Data
Bus
Switch
Clock
Gen.
XTAL
EXTAL
RESET
PINIT/NMI
Power
Mgmt.
PLL
Program
Interrupt
Controller
Program
Decode
Controller
Program
Address
Generator
Data ALU
24 × 24+56→56-bit MAC
Two 56-bit Accumulators
56-bit Barrel Shifter
4
JTAG
OnCE
MODA/IRQA/GPIO
MODB/IRQB/GPIO
MODC/IRQC/GPIO
MODD/IRQD/GPIO
* ESAI_1 and dedicated GPIO pins are not available in the 52-pin package.
Figure 1. DSP56374 Block Diagram
2
Features
2.1
DSP56300 Modular Chassis
•
•
•
•
150 Million Instructions Per Second (MIPS) with a 150 MHz clock at an internal logic supply
(QVDDL) of 1.25 V
Object Code Compatible with the 56K core
Data ALU with a 24 x 24 bit multiplier-accumulator and a 56-bit barrel shifter;16 bit arithmetic
support
Program Control with position independent code support
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
3
Features
•
•
•
•
•
•
2.2
•
•
•
•
•
Six-channel DMA controller
Provides a wide range of frequency multiplications (1 to 255), predivider factors (1 to 31), PLL
feedback multiplier (2 or 4), Output divide factor (1, 2, or 4) and a power-saving clock divider
(2i: i = 0 to 7) to reduce clock noise
Internal address tracing support and OnCE for Hardware/Software debugging
JTAG port, supporting boundary scan, compliant to IEEE 1149.1
Very low-power CMOS design, fully static design with operating frequencies down to DC
STOP and WAIT low-power standby modes
On-chip Memory Configuration
6Kx24 Bit Y-Data RAM and 4Kx24 Bit Y-Data ROM
6Kx24 Bit X-Data RAM and 4Kx24 Bit X-Data ROM
20Kx24 Bit Program and Bootstrap ROM including a PROM patching mechanism
6Kx24 Bit Program RAM.
Various memory switches are available. See memory table below.
Table 1. DSP56374 Memory Switch Configurations
Bit Settings
2.3
•
•
•
•
•
Memory Sizes (24-bit words)
MSW1
MSW0
MS
Prog
RAM
X Data
RAM
Y Data
RAM
Prog
ROM
X Data
ROM
Y Data
ROM
X
X
0
6K
6K
6K
20K
4K
4K
0
0
1
2K
10K
6K
20K
4K
4K
0
1
1
4K
8K
6K
20K
4K
4K
1
0
1
8K
4K
6K
20K
4K
4K
1
1
1
10K
4K
4K
20K
4K
4K
Peripheral Modules
Enhanced Serial Audio Interface (ESAI): up to 4 receiver pins and up to 6 transmitter pins, master
or slave. I2S, Sony, AC97, network, and other programmable protocols.
Enhanced Serial Audio Interface I (ESAI_1): up to 4 receiver pins and up to 6 transmitter pins,
master or slave. I2S, Sony, AC97, network and other programmable protocols. Note: Available in
the 80-pin package only.
Serial Host Interface (SHI): SPI and I2C protocols, 10-word receive FIFO, support for 8, 16, and
24-bit words. Three noise reduction filter modes.
Triple Timer module (TEC)
Most pins of unused peripherals may be programmed as GPIO pins. Up to 47 pins can be
configured as GPIO on the 80 pin package and 20 pins on the 52 pin package.
DSP56374 Data Sheet, Rev. 4.2
4
Freescale Semiconductor
Documentation
•
Hardware Watchdog Timer
2.4
Packages
80-pin and 52-pin plastic LQFP packages.
3
Documentation
Table 2 lists the documents that provide a complete description of the DSP56374 and are required to design
properly with the part. Documentation is available from a local Freescale Semiconductor, Inc. (formerly
Motorola) distributor, semiconductor sales office, Literature Distribution Center, or through the Freescale
DSP home page on the Internet (the source for the latest information).
Table 2. DSP56374 Documentation
Document Name
Description
Order Number
DSP56300 Family Manual
Detailed description of the 56300-family architecture and the
24-bit core processor and instruction set
DSP56300FM/AD
DSP56374 User’s Manual
Detailed description of memory, peripherals, and interfaces
DSP56374UM/D
DSP56374 Technical Data Sheet
Electrical and timing specifications; pin and package
descriptions
DSP56374 Product Brief
Brief description of the chip
4
DSP56374
DSP56374PB/D
Signal Groupings
The input and output signals of the DSP56374 are organized into functional groups, which are listed in
Table 3.
The DSP56374 is operated from a 1.25 V and 3.3 V supply; however, some of the inputs can tolerate 5.0 V.
A special notice for this feature is added to the signal descriptions of those inputs.
Table 3. DSP56374 Functional Signal Groupings
Number of
Signals1
Detailed
Description
Power (VDD)
11
Table 15
Ground (GND)
9
Table 5
Scan Pins
1
Table 6
Clock and PLL
3
Table 7
Port H2
5
Table 8
SHI
Port
H2
5
Table 9
ESAI
Port C4
12
Table 10
E5
12
Table 11
Functional Group
Interrupt and mode control
ESAI_1
Port
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
5
Signal Groupings
Table 3. DSP56374 Functional Signal Groupings (continued)
Number of
Signals1
Detailed
Description
15
Table 12
Timer
3
Table 13
JTAG/OnCE Port
4
Table 14
Functional Group
Port G3
Dedicated GPIO
Note:
1
Pins are not 5 V. tolerant unless noted.
2
Port H signals are the GPIO port signals which are multiplexed with the MOD and HREQ signals.
3
Port G signals are the dedicated GPIO port signals.
4
Port C signals are the GPIO port signals which are multiplexed with the ESAI signals.
5
Port E signals are the GPIO port signals which are multiplexed with the ESAI_1 signals.
4.1
Power
Table 4. Power Inputs
4.2
Power Name
Description
PLLA_VDD (1)
PLL Power— The voltage (3.3 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 3.3 VDD power rail. The user must provide adequate
external decoupling capacitors between PLLA_VDD and PLLA_GND. PLLA_VDD requires a filter
as shown in Figure 1 and Figure 2 below. See the DSP56374 technical data sheet for additional
details.
PLLP_VDD(1)
PLL Power— The voltage (3.3 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 3.3 VDD power rail. The user must provide adequate
external decoupling capacitors between PLLP_VDD and PLLP_GND.
PLLD_VDD (1)
PLL Power— The voltage (1.25 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 1.25 VDD power rail. The user must provide adequate
external decoupling capacitors between PLLD_VDD and PLLD_GND.
CORE_VDD (4)
Core Power—The voltage (1.25 V) should be well-regulated and the input should be provided with
an extremely low impedance path to the 1.25 VDD power rail. The user must provide adequate
external decoupling capacitors.
IO_VDD
(80-pin 4)
(52-pin 3)
SHI, ESAI, ESAI_1, WDT and Timer I/O Power —The voltage (3.3 V) should be well-regulated,
and the input should be provided with an extremely low impedance path to the 3.3 VDD power rail.
This is an isolated power for the SHI, ESAI, ESAI_1, WDT and Timer I/O. The user must provide
adequate external decoupling capacitors.
Ground
Table 5. Grounds
Ground Name
Description
PLLA_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLA_VDD and PLLA_GND.
DSP56374 Data Sheet, Rev. 4.2
6
Freescale Semiconductor
Signal Groupings
Table 5. Grounds (continued)
4.3
Ground Name
Description
PLLP_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLP_VDD and PLLP_GND.
PLLD_GND(1)
PLL Ground—The PLL ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors between PLLD_VDD and PLLD_GND.
CORE_GND(4)
Core Ground—The Core ground should be provided with an extremely low-impedance path to
ground. This connection must be tied externally to all other chip ground connections. The user
must provide adequate external decoupling capacitors.
IO_GND(2)
SHI, ESAI, ESAI_1, WDT and Timer I/O Ground—IO_GND is the ground for the SHI, ESAI,
ESAI_1, WDT and Timer I/O. This connection must be tied externally to all other chip ground
connections. The user must provide adequate external decoupling capacitors.
SCAN
Table 6. SCAN Signals
4.4
Signal
Name
Type
State
During
Reset
SCAN
Input
Input
Signal Description
SCAN—Manufacturing test pin. This pin must be connected to ground.
Clock and PLL
Table 7. Clock and PLL Signals
Signal
Name
Type
State
during
Reset
EXTAL
Input
Input
XTAL
Output
PINIT/NMI
Input
Signal Description
External Clock / Crystal Input—An external clock source must be connected
to EXTAL in order to supply the clock to the internal clock generator and PLL.
Chip Driven Crystal Output—Connects the internal Crystal Oscillator output to an external
crystal. If an external clock is used, leave XTAL unconnected.
Input
PLL Initial/Nonmaskable Interrupt—During assertion of RESET, the value of
PINIT/NMI is written into the PLL Enable (PEN) bit of the PLL control register,
determining whether the PLL is enabled or disabled. After RESET
de-assertion and during normal instruction processing, the PINIT/NMI
Schmitt-trigger input is a negative-edge-triggered nonmaskable interrupt
(NMI) request internally synchronized to the internal system clock.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
7
Signal Groupings
4.5
Interrupt and Mode Control
The interrupt and mode control signals select the chip’s operating mode as it comes out of hardware reset.
After RESET is de-asserted, these inputs are hardware interrupt request lines.
Table 8. Interrupt and Mode Control
Signal Name
Type
MODA/IRQA
Input
State
during
Reset
MODA
Input
Signal Description
Mode Select A/External Interrupt Request A—MODA/IRQA is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODA/IRQA selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or
negative-edge-triggered, maskable interrupt request input during
normal instruction processing. This pin can also be programmed as
GPIO. MODA, MODB, MODC, and MODD select one of 16 initial chip
operating modes, latched into the OMR when the RESET signal is
de-asserted. If the processor is in the stop standby state and the
MODA/IRQA pin is pulled to GND, the processor will exit the stop state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH0
Input, output,
or
disconnected
MODB/IRQB
Input
Port H0—When the MODA/IRQA is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODB
Input
Mode Select B/External Interrupt Request B—MODB/IRQB is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODB/IRQB selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or
negative-edge-triggered, maskable interrupt request input during
normal instruction processing. This pin can also be programmed as
GPIO. MODA, MODB, MODC, and MODD select one of 16 initial chip
operating modes, latched into OMR when the RESET signal is
de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH1
Input, output,
or
disconnected
MODC/IRQC
Input
Port H1—When the MODB/IRQB is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODC
Input
Mode Select C/External Interrupt Request C—MODC/IRQC is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODC/IRQC selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or
negative-edge-triggered, maskable interrupt request input during
normal instruction processing. This pin can also be programmed as
GPIO. MODA, MODB, MODC, and MODD select one of 16 initial chip
operating modes, latched into OMR when the RESET signal is
de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
8
Freescale Semiconductor
Signal Groupings
Table 8. Interrupt and Mode Control (continued)
Signal Name
Type
PH2
Input, output,
or
disconnected
MODD/IRQD
Input
State
during
Reset
Signal Description
Port H2—When the MODC/IRQC is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
MODD
Input
Mode Select D/External Interrupt Request D—MODD/IRQD is an
active-low Schmitt-trigger input, internally synchronized to the DSP
clock. MODD/IRQD selects the initial chip operating mode during
hardware reset and becomes a level-sensitive or
negative-edge-triggered, maskable interrupt request input during
normal instruction processing. This pin can also be programmed as
GPIO. MODA, MODB, MODC, and MODD select one of 16 initial chip
operating modes, latched into OMR when the RESET signal is
de-asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
PH3
Input, output,
or
disconnected
RESET
Input
Port H3—When the MODD/IRQD is configured as GPIO, this signal is
individually programmable as input, output, or internally disconnected.
Input
Reset—RESET is an active-low, Schmitt-trigger input. When asserted,
the chip is placed in the Reset state and the internal phase generator is
reset. The Schmitt-trigger input allows a slowly rising input (such as a
capacitor charging) to reset the chip reliably. When the RESET signal is
de-asserted, the initial chip operating mode is latched from the MODA,
MODB, MODC, and MODD inputs. The RESET signal must be asserted
during power up. A stable EXTAL signal must be supplied while RESET
is being asserted.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
4.6
Serial Host Interface
The SHI has five I/O signals that can be configured to allow the SHI to operate in either SPI or I2C mode.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
9
Signal Groupings
Table 9. Serial Host Interface Signals
Signal
Name
Signal Type
State during
Reset
SCK
Input or output
Tri-stated
SCL
Input or output
Signal Description
SPI Serial Clock—The SCK signal is an output when the SPI is configured
as a master and a Schmitt-trigger input when the SPI is configured as a
slave. When the SPI is configured as a master, the SCK signal is derived
from the internal SHI clock generator. When the SPI is configured as a
slave, the SCK signal is an input, and the clock signal from the external
master synchronizes the data transfer. The SCK signal is ignored by the SPI
if it is defined as a slave and the slave select (SS) signal is not asserted. In
both the master and slave SPI devices, data is shifted on one edge of the
SCK signal and is sampled on the opposite edge where data is stable. Edge
polarity is determined by the SPI transfer protocol.
I2C Serial Clock—SCL carries the clock for I2C bus transactions in the I2C
mode. SCL is a Schmitt-trigger input when configured as a slave and an
open-drain output when configured as a master. SCL should be connected
to VDD through an external pull-up resistor according to the I2C
specifications.
This signal is tri-stated during hardware, software, and individual reset.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
MISO
Input or output
SDA
Input or
open-drain
output
Tri-stated
SPI Master-In-Slave-Out—When the SPI is configured as a master, MISO
is the master data input line. The MISO signal is used in conjunction with the
MOSI signal for transmitting and receiving serial data. This signal is a
Schmitt-trigger input when configured for the SPI Master mode, an output
when configured for the SPI Slave mode, and tri-stated if configured for the
SPI Slave mode when SS is de-asserted. An external pull-up resistor is not
required for SPI operation.
I2C Data and Acknowledge—In I2C mode, SDA is a Schmitt-trigger input
when receiving and an open-drain output when transmitting. SDA should be
connected to VDD through a pull-up resistor. SDA carries the data for I2C
transactions. The data in SDA must be stable during the high period of SCL.
The data in SDA is only allowed to change when SCL is low. When the bus
is free, SDA is high. The SDA line is only allowed to change during the time
SCL is high in the case of start and stop events. A high-to-low transition of
the SDA line while SCL is high is a unique situation, and is defined as the
start event. A low-to-high transition of SDA while SCL is high is a unique
situation defined as the stop event.
This signal is tri-stated during hardware, software, and individual reset.
Thus, there is no need for an external pull-up in this state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
10
Freescale Semiconductor
Signal Groupings
Table 9. Serial Host Interface Signals (continued)
Signal
Name
Signal Type
State during
Reset
MOSI
Input or output
Tri-stated
HA0
Input
Signal Description
SPI Master-Out-Slave-In—When the SPI is configured as a master, MOSI
is the master data output line. The MOSI signal is used in conjunction with
the MISO signal for transmitting and receiving serial data. MOSI is the slave
data input line when the SPI is configured as a slave. This signal is a
Schmitt-trigger input when configured for the SPI Slave mode.
I2C Slave Address 0—This signal uses a Schmitt-trigger input when
configured for the I2C mode. When configured for I2C slave mode, the HA0
signal is used to form the slave device address. HA0 is ignored when
configured for the I2C master mode.
This signal is tri-stated during hardware, software, and individual reset.
Thus, there is no need for an external pull-up in this state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
SS
Input
Ignored Input SPI Slave Select—This signal is an active low Schmitt-trigger input when
configured for the SPI mode. When configured for the SPI Slave mode, this
signal is used to enable the SPI slave for transfer. When configured for the
SPI master mode, this signal should be kept de-asserted (pulled high). If it
is asserted while configured as SPI master, a bus error condition is flagged.
If SS is de-asserted, the SHI ignores SCK clocks and keeps the MISO
output signal in the high-impedance state.
HA2
Input
I2C Slave Address 2—This signal uses a Schmitt-trigger input when
configured for the I2C mode. When configured for the I2C Slave mode, the
HA2 signal is used to form the slave device address. HA2 is ignored in the
I2C master mode.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
HREQ
Input or Output
Tri-stated
Host Request—This signal is an active low Schmitt-trigger input when
configured for the master mode but an active low output when configured for
the slave mode.
When configured for the slave mode, HREQ is asserted to indicate that the
SHI is ready for the next data word transfer and de-asserted at the first clock
pulse of the new data word transfer. When configured for the master mode,
HREQ is an input. When asserted by the external slave device, it will trigger
the start of the data word transfer by the master. After finishing the data word
transfer, the master will await the next assertion of HREQ to proceed to the
next transfer. This pin can also be programmed as GPIO.
PH4
Input, output, or
disconnected
Port H4—When HREQ is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
11
Signal Groupings
4.7
Enhanced Serial Audio Interface
Table 10. Enhanced Serial Audio Interface Signals
Signal Name
Signal Type
HCKR
Input or output
PC2
Input, output, or
disconnected
State during
Reset
GPIO
disconnected
Signal Description
High Frequency Clock for Receiver—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI receiver as an alternate to the DSP
core clock. When programmed as an output, this signal can
serve as a high-frequency sample clock (e.g., for external
digital to analog converters [DACs]) or as an additional
system clock.
Port C2—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
HCKT
Input or output
PC5
Input, output, or
disconnected
GPIO
disconnected
High Frequency Clock for Transmitter—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI transmitter as an alternate to the DSP
core clock. When programmed as an output, this signal can
serve as a high frequency sample clock (e.g., for external
DACs) or as an additional system clock.
Port C5—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
12
Freescale Semiconductor
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (continued)
Signal Name
Signal Type
FSR
Input or output
State during
Reset
GPIO
disconnected
Signal Description
Frame Sync for Receiver—This is the receiver frame sync
input/output signal. In the asynchronous mode (SYN=0),
the FSR pin operates as the frame sync input or output
used by all the enabled receivers. In the synchronous mode
(SYN=1), it operates as either the serial flag 1 pin
(TEBE=0), or as the transmitter external buffer enable
control (TEBE=1, RFSD=1).
When this pin is configured as serial flag pin, its direction is
determined by the RFSD bit in the RCCR register. When
configured as the output flag OF1, this pin will reflect the
value of the OF1 bit in the SAICR register, and the data in
the OF1 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF1, the data value at the
pin will be stored in the IF1 bit in the SAISR register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PC1
Input, output, or
disconnected
Port C1—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
FST
Input or output
PC4
Input, output, or
disconnected
GPIO
disconnected
Frame Sync for Transmitter—This is the transmitter frame
sync input/output signal. For synchronous mode, this signal
is the frame sync for both transmitters and receivers. For
asynchronous mode, FST is the frame sync for the
transmitters only. The direction is determined by the
transmitter frame sync direction (TFSD) bit in the ESAI
transmit clock control register (TCCR).
Port C4—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
13
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (continued)
Signal Name
Signal Type
SCKR
Input or output
State during
Reset
GPIO
disconnected
Signal Description
Receiver Serial Clock—SCKR provides the receiver serial
bit clock for the ESAI. The SCKR operates as a clock input
or output used by all the enabled receivers in the
asynchronous mode (SYN=0), or as serial flag 0 pin in the
synchronous mode (SYN=1).
When this pin is configured as serial flag pin, its direction is
determined by the RCKD bit in the RCCR register. When
configured as the output flag OF0, this pin will reflect the
value of the OF0 bit in the SAICR register, and the data in
the OF0 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF0, the data value at the
pin will be stored in the IF0 bit in the SAISR register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PC0
Input, output, or
disconnected
Port C0—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SCKT
Input or output
PC3
Input, output, or
disconnected
GPIO
disconnected
Transmitter Serial Clock—This signal provides the serial bit
rate clock for the ESAI. SCKT is a clock input or output used
by all enabled transmitters and receivers in synchronous
mode, or by all enabled transmitters in asynchronous
mode.
Port C3—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
14
Freescale Semiconductor
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (continued)
Signal Name
Signal Type
SDO5
Output
SDI0
Input
PC6
Input, output, or
disconnected
State during
Reset
GPIO
disconnected
Signal Description
Serial Data Output 5—When programmed as a transmitter,
SDO5 is used to transmit data from the TX5 serial transmit
shift register.
Serial Data Input 0—When programmed as a receiver,
SDI0 is used to receive serial data into the RX0 serial
receive shift register.
Port C6—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO4
Output
SDI1
Input
PC7
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 4—When programmed as a transmitter,
SDO4 is used to transmit data from the TX4 serial transmit
shift register.
Serial Data Input 1—When programmed as a receiver,
SDI1 is used to receive serial data into the RX1 serial
receive shift register.
Port C7—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO3
Output
SDI2
Input
PC8
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 3—When programmed as a
transmitter, SDO3 is used to transmit data from the TX3
serial transmit shift register.
Serial Data Input 2—When programmed as a receiver,
SDI2 is used to receive serial data into the RX2 serial
receive shift register.
Port C8—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
15
Signal Groupings
Table 10. Enhanced Serial Audio Interface Signals (continued)
Signal Name
Signal Type
SDO2
Output
SDI3
Input
PC9
Input, output, or
disconnected
State during
Reset
GPIO
disconnected
Signal Description
Serial Data Output 2—When programmed as a transmitter,
SDO2 is used to transmit data from the TX2 serial transmit
shift register
Serial Data Input 3—When programmed as a receiver,
SDI3 is used to receive serial data into the RX3 serial
receive shift register.
Port C9—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO1
Output
PC10
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 1—SDO1 is used to transmit data from
the TX1 serial transmit shift register.
Port C10—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO0
Output
PC11
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 0—SDO0 is used to transmit data from
the TX0 serial transmit shift register.
Port C11—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
16
Freescale Semiconductor
Signal Groupings
4.8
Enhanced Serial Audio Interface_1
Table 11. Enhanced Serial Audio Interface_1 Signals
Signal Name
Signal Type
HCKR_1
Input or output
PE2
Input, output, or
disconnected
State during
Reset
GPIO
disconnected
Signal Description
High Frequency Clock for Receiver—When programmed as
an input, this signal provides a high frequency clock source
for the ESAI_1 receiver as an alternate to the DSP core
clock. When programmed as an output, this signal can
serve as a high-frequency sample clock (e.g., for external
digital to analog converters [DACs]) or as an additional
system clock.
Port E2—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
HCKT_1
Input or output
PE5
Input, output, or
disconnected
GPIO
disconnected
High Frequency Clock for Transmitter—When programmed
as an input, this signal provides a high frequency clock
source for the ESAI_1 transmitter as an alternate to the
DSP core clock. When programmed as an output, this
signal can serve as a high frequency sample clock (e.g., for
external DACs) or as an additional system clock.
Port E5—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
17
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (continued)
Signal Name
Signal Type
FSR_1
Input or output
State during
Reset
GPIO
disconnected
Signal Description
Frame Sync for Receiver_1—This is the receiver frame
sync input/output signal. In the asynchronous mode
(SYN=0), the FSR_1 pin operates as the frame sync input
or output used by all the enabled receivers. In the
synchronous mode (SYN=1), it operates as either the serial
flag 1 pin (TEBE=0), or as the transmitter external buffer
enable control (TEBE=1, RFSD=1).
When this pin is configured as serial flag pin, its direction is
determined by the RFSD bit in the RCCR_1 register. When
configured as the output flag OF1, this pin will reflect the
value of the OF1 bit in the SAICR_1 register, and the data
in the OF1 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF1, the data value at the
pin will be stored in the IF1 bit in the SAISR_1 register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PE1
Input, output, or
disconnected
Port E1—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
FST_1
Input or output
PE4
Input, output, or
disconnected
GPIO
disconnected
Frame Sync for Transmitter_1—This is the transmitter frame
sync input/output signal. For synchronous mode, this signal
is the frame sync for both transmitters and receivers. For
asynchronous mode, FST_1 is the frame sync for the
transmitters only. The direction is determined by the
transmitter frame sync direction (TFSD) bit in the ESAI_1
transmit clock control register (TCCR_1).
Port E4—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
18
Freescale Semiconductor
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (continued)
Signal Name
Signal Type
SCKR_1
Input or output
State during
Reset
GPIO
disconnected
Signal Description
Receiver Serial Clock_1—SCKR_1 provides the receiver
serial bit clock for the ESAI_1. The SCKR_1 operates as a
clock input or output used by all the enabled receivers in the
asynchronous mode (SYN=0), or as serial flag 0 pin in the
synchronous mode (SYN=1).
When this pin is configured as serial flag pin, its direction is
determined by the RCKD bit in the RCCR_1 register. When
configured as the output flag OF0, this pin will reflect the
value of the OF0 bit in the SAICR_1 register, and the data
in the OF0 bit will show up at the pin synchronized to the
frame sync in normal mode or the slot in network mode.
When configured as the input flag IF0, the data value at the
pin will be stored in the IF0 bit in the SAISR_1 register,
synchronized by the frame sync in normal mode or the slot
in network mode.
PE0
Input, output, or
disconnected
Port E0—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
SCKT_1
Input or output
PE3
Input, output, or
disconnected
GPIO
disconnected
Transmitter Serial Clock_1—This signal provides the serial
bit rate clock for the ESAI_1. SCKT_1 is a clock input or
output used by all enabled transmitters and receivers in
synchronous mode, or by all enabled transmitters in
asynchronous mode.
Port E3—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
19
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (continued)
Signal Name
Signal Type
SDO5_1
Output
SDI0_1
Input
PE6
Input, output, or
disconnected
State during
Reset
GPIO
disconnected
Signal Description
Serial Data Output 5_1—When programmed as a
transmitter, SDO5_1 is used to transmit data from the TX5
serial transmit shift register.
Serial Data Input 0_1—When programmed as a receiver,
SDI0_1 is used to receive serial data into the RX0 serial
receive shift register.
Port E6—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
SDO4_1
Output
SDI1_1
Input
PE7
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 4_1—When programmed as a
transmitter, SDO4_1 is used to transmit data from the TX4
serial transmit shift register.
Serial Data Input 1_1—When programmed as a receiver,
SDI1_1 is used to receive serial data into the RX1 serial
receive shift register.
Port E7—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO3_1
Output
SDI2_1
Input
PE8
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 3—When programmed as a transmitter,
SDO3_1 is used to transmit data from the TX3 serial
transmit shift register.
Serial Data Input 2—When programmed as a receiver,
SDI2_1 is used to receive serial data into the RX2 serial
receive shift register.
Port E8—When the ESAI is configured as GPIO, this signal
is individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
20
Freescale Semiconductor
Signal Groupings
Table 11. Enhanced Serial Audio Interface_1 Signals (continued)
State during
Reset
Signal Name
Signal Type
SDO2_1
Output
SDI3_1
Input
Serial Data Input 3—When programmed as a receiver,
SDI3_1 is used to receive serial data into the RX3 serial
receive shift register.
PE9
Input, output, or
disconnected
Port E9—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
GPIO
disconnected
Signal Description
Serial Data Output 2—When programmed as a transmitter,
SDO2_1 is used to transmit data from the TX2 serial
transmit shift register.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO1_1
Output
PE10
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 1—SDO1_1 is used to transmit data
from the TX1 serial transmit shift register.
Port E10—When the ESAI is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO0_1
Output
PE11
Input, output, or
disconnected
GPIO
disconnected
Serial Data Output 0—SDO0_1 is used to transmit data
from the TX0 serial transmit shift register.
Port E11—When the ESAI_1 is configured as GPIO, this
signal is individually programmable as input, output, or
internally disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
21
Signal Groupings
4.9
Dedicated GPIO-Port G
Table 12. Dedicated GPIO-Port G Signals
Signal
Name
PG0
Type
Input,
output, or
disconnected
State During
Reset
GPIO
disconnected
Signal Description
Port G0—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG1
Input,
output, or
disconnected
GPIO
disconnected
Port G1—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG2
Input,
output, or
disconnected
GPIO
disconnected
Port G2—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG3
Input,
output, or
disconnected
GPIO
disconnected
Port G3—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG4
Input,
output, or
disconnected
GPIO
disconnected
Port G4—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG5
Input,
output, or
disconnected
GPIO
disconnected
Port G5—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG6
Input,
output, or
disconnected
GPIO
disconnected
Port G6—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG7
Input,
output, or
disconnected
GPIO
disconnected
Port G7—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG8
Input,
output, or
disconnected
GPIO
disconnected
Port G8—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
DSP56374 Data Sheet, Rev. 4.2
22
Freescale Semiconductor
Signal Groupings
Table 12. Dedicated GPIO-Port G Signals (continued)
Signal
Name
PG9
Type
Input,
output, or
disconnected
State During
Reset
GPIO
disconnected
Signal Description
Port G9—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG10
Input,
output, or
disconnected
GPIO
disconnected
Port G10—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG11
Input,
output, or
disconnected
GPIO
disconnected
Port G11—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG12
Input,
output, or
disconnected
GPIO
disconnected
Port G12—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG13
Input,
output, or
disconnected
GPIO
disconnected
Port G13—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
PG14
Input,
output, or
disconnected
GPIO
disconnected
Port G14—This signal is individually programmable as input,
output, or internally disconnected.
Internal Pull down resistor.
This input is 5 V tolerant
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
23
Signal Groupings
4.10 Timer
Table 13. Timer Signal
Signal
Name
TIO0
Type
Input or
Output
State
during
Reset
Signal Description
GPIO Input Timer 0 Schmitt-Trigger Input/Output—When timer 0 functions as an
external event counter or in measurement mode, TIO0 is used as input.
When timer 0 functions in watchdog, timer, or pulse modulation mode,
TIO0 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer 0
control/status register (TCSR0). If TIO0 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input.
Internal Pull down resistor.
This input is 5 V tolerant
TIO1
Input or
Output
Watchdog
Timer
Output
Timer 1 Schmitt-Trigger Input/Output—When timer 1 functions as an
external event counter or in measurement mode, TIO1 is used as input.
When timer 1 functions in watchdog, timer, or pulse modulation mode,
TIO1 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer
1control/status register (TCSR1). If TIO1 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input.
WDT
Output
WDT—When this pin is configured as a hardware watchdog timer pin,
this signal is asserted low when the hardware watchdog timer counts
down to zero.
Internal Pull down resistor.
This input is 5 V tolerant
TIO2
Input or
Output
PLOCK
Output
Timer 2 Schmitt-Trigger Input/Output—When timer 2 functions as an
external event counter or in measurement mode, TIO2 is used as input.
When timer 2 functions in watchdog, timer, or pulse modulation mode,
TIO2 is used as output.
The default mode after reset is GPIO input. This can be changed to
output or configured as a timer input/output through the timer
control/status register (TCSR2). If TIO2 is not being used, it is
recommended to either define it as GPIO output immediately at the
beginning of operation or leave it defined as GPIO input .
DSP56374 Data Sheet, Rev. 4.2
24
Freescale Semiconductor
Maximum Ratings
Table 13. Timer Signal (continued)
Signal
Name
Type
PLOCK
Output
State
during
Reset
Signal Description
PLOCK—When this pin is configured as a PLL lock pin, this signal is
asserted high when the on-chip PLL enabled and locked and
de-asserted when the PLL enabled and unlocked. This pin is also
asserted high when the PLL is disabled.
Internal Pull down resistor.
This input is 5 V tolerant
4.11 JTAG/OnCE Interface
Table 14. JTAG/OnCE Interface
Signal
Name
Signal
Type
State
during
Reset
TCK
Input
Input
Signal Description
Test Clock—TCK is a test clock input signal used to synchronize the JTAG test
logic.
Internal Pull up resistor.
This input is 5 V tolerant.
TDI
Input
Input
Test Data Input—TDI is a test data serial input signal used for test instructions
and data. TDI is sampled on the rising edge of TCK.
Internal Pull up resistor.
This input is 5 V tolerant.
TDO
Output
Tri-stated
TMS
Input
Input
Test Data Output—TDO is a test data serial output signal used for test
instructions and data. TDO is tri-statable and is actively driven in the shift-IR
and shift-DR controller states. TDO changes on the falling edge of TCK.
Test Mode Select—TMS is an input signal used to sequence the test
controller’s state machine. TMS is sampled on the rising edge of TCK.
Internal Pull up resistor.
This input is 5 V tolerant.
5
Maximum Ratings
CAUTION
This device contains circuitry protecting against damage due to high static voltage
or electrical fields. However, normal precautions should be taken to avoid
exceeding maximum voltage ratings. Reliability of operation is enhanced if unused
inputs are pulled to an appropriate logic voltage level (e.g., either GND or VDD).
The suggested value for a pullup or pulldown resistor is 4.7 kΩ.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
25
Power Requirements
NOTE
In the calculation of timing requirements, adding a maximum value of one
specification to a minimum value of another specification does not yield a
reasonable sum. A maximum specification is calculated using a worst case variation
of process parameter values in one direction. The minimum specification is
calculated using the worst case for the same parameters in the opposite direction.
Therefore, a “maximum” value for a specification will never occur in the same
device that has a “minimum” value for another specification; adding a maximum to
a minimum represents a condition that can never exist.
Table 15. Maximum Ratings
Rating1
Value1, 2
Unit
−0.3 to + 1.6
V
VPLLP_VDD,
VIO_VDD,
VPLLA_VDD,
−0.3 to + 4.0
V
Tr
10
ms
VIN
GND − 0.3 to 6V
V
I
12
mA
ISCK
16
mA
IJTAG
24
ma
TJ
80 LQFP = 105
52 LQFP = 110
°C
−55 to +125
°C
ESD protected voltage (Human Body Model)
2000
V
ESD protected voltage (Machine Model)
200
V
Symbol
Supply Voltage
VCORE_VDD,
VPLLD_VDD
Maximum CORE_VDD power supply ramp time4
All “5.0V tolerant” input voltages
Current drain per pin excluding VDD and GND(Except
for pads listed below)
SCK_SCL
TDO
Operating temperature
range3
Storage temperature
TSTG
Note:
1 GND = 0 V, T = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50pF
J
2 Absolute maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed.
Stress beyond the maximum rating may affect device reliability or cause permanent damage to the device.
3 Operating temperature qualified for automotive applications. T = T + θ x Power. Variables used were
J
A
JA
Core Current = 100 mA, I/O Current = 60 mA, Core Voltage = 1.3 V, I/O Voltage = 3.46 V, TA = 85°C
4 If the power supply ramp to full supply time is longer than 10 ms, the POR circuitry will not operate correctly,
causing erroneous operation.
6
Power Requirements
To prevent high current conditions due to possible improper sequencing of the power supplies, the
connection shown below is recommended to be made between the DSP56374 IO_VDD and Core_VDD
power pins.
DSP56374 Data Sheet, Rev. 4.2
26
Freescale Semiconductor
Thermal Characteristics
IO_VDD
External
Schottky
Diode
Core_VDD
To prevent a high current condition upon power up, the IO_VDD must be applied ahead of the Core_VDD
as shown below if the external Schottky is not used.
Core_VDD
IO_VDD
For correct operation of the internal power on reset logic, the Core_VDD ramp rate (Tr) to full supply must
be less than 10 ms. This is shown below.
Tr
1.25 V
0V
Core_VDD
7
Thermal Characteristics
Table 16. Thermal Characteristics
Characteristic
Symbol
LQFP Values
Unit
Natural Convection, Junction-to-ambient thermal
resistance1,2
RθJA or θJA
68 (52 LQFP)
50 (80 LQFP)
°C/W
Junction-to-case thermal resistance3
RθJC or θJC
17 (52 LQFP)
11 (80 LQFP)
°C/W
Note:
1
Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance,
mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components
on the board, and board thermal resistance.
2 Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3 Thermal resistance between the die and the case top surface as measured by the cold plate method
(MIL SPEC-883 Method 1012.1).
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
27
DC Electrical Characteristics
8
DC Electrical Characteristics
Table 17. DC Electrical Characteristics
Characteristics
Symbol
Min
Typ
Max
Unit
Supply voltages
• Core (Core_VDD)
• PLL (PLLD_VDD)
VDD
1.2
1.25
1.3
V
Supply voltages
• I/O (IO_VDD)
• PLL (PLLP_VDD)
• PLL (PLLA_VDD)
VDDIO
3.14
3.3
3.46
V
VIH
2.0
—
VIO_VDD+2V
V
Input high voltage
• All pins
Note: All 3.3-V supplies must rise prior to the rise of the 1.25-V supplies to avoid a high current condition and possible
system damage.
Input low voltage
• All pins
VIL
–0.3
—
0.8
V
Input leakage current
IIN
—
—
± 84
µA
Clock pin Input Capacitance (EXTAL)
CIN
High impedance (off-state) input current (@ 3.46V)
ITSI
–10
—
84
µA
Output high voltage
• IOH = -5 mA
• XTAL Pin IOH = -10mA
VOH
2.4
—
—
V
Output low voltage
• IOL = 5 mA
• XTAL Pin IOL = 10 mA
VOL
—
—
0.4
V
ICCI
—
65
100
mA
ICCW
—
16
—
mA
ICCS
—
1.2
—
mA
CIN
—
—
10
pF
Internal supply current1 (core only) at internal clock of
150 MHz
• In Normal mode
• In Wait mode
• In Stop
mode2
Input capacitance
4.7
pF
Note:
1 The Current Consumption section provides a formula to compute the estimated current requirements in Normal
mode. In order to obtain these results, all inputs must be terminated (i.e., not allowed to float). Measurements are
based on synthetic intensive DSP benchmarks. The power consumption numbers in this specification are 90% of
the measured results of this benchmark. This reflects typical DSP applications. Typical internal supply current is
measured with VCORE_VDD = 1.25V, VDD_IO = 3.3V at TJ = 25°C. Maximum internal supply current is measured
with VCORE_VDD = 1.30V, VIO_VDD) = 3.46V at TJ = 115°C.
2 In order to obtain these results, all inputs, which are not disconnected at Stop mode, must be terminated (i.e., not
allowed to float).
DSP56374 Data Sheet, Rev. 4.2
28
Freescale Semiconductor
AC Electrical Characteristics
9
AC Electrical Characteristics
The timing waveforms shown in the AC electrical characteristics section are tested with a VIL maximum
of 0.8 V and a VIH minimum of 2.0 V for all pins. AC timing specifications, which are referenced to a
device input signal, are measured in production with respect to the 50% point of the respective input
signal’s transition. DSP56374 output levels are measured with the production test machine VOL and VOH
reference levels set at 1.0 V and 1.8 V, respectively.
10
Internal Clocks
Table 18. INTERNAL CLOCKS1
No.
Characteristics
Symbol
Min
Typ
Max
Unit
5
—
20
MHz
1
Comparison Frequency
Fref
2
Input Clock Frequency
FIN
3
Output clock Frequency (with
PLL enabled) 2,3
4
Output clock Frequency (with
PLL disabled) 2,3
5
Duty Cycle
Fref*NR
(Ef × MF x FM)/
(PDF × DF x OD)
Condition
Fref = FIN/NR
NR is input divider value
FOUT
75
150
MHz
Tc
13.3
FOUT
—
Ef
150
MHz
—
40
50
60
%
FOUT=FVCO/NO where
NO is output divider value
ns
—
FVCO=300MHz~600MHz
Note:
1 See users manual for definition.
2 DF = Division Factor
Ef = External Frequency
Mf = Multiplication Factor
PDF = Predivision Factor
FM= Frequency Multiplier
OD = Output Divider
Tc = Internal Clock Period
3 Maximum frequency will vary depending on the ordered part number.
11
External Clock Operation
The DSP56374 system clock is derived from the on-chip oscillator or is externally supplied. To use the
on-chip oscillator, connect a crystal and associated resistor/capacitor components to EXTAL and XTAL;
an example is shown below.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
29
External Clock Operation
Suggested component values:
f
osc = 24.576 MHz
R = 1 M ±10%
C (EXTAL)= 18 pF
C (XTAL) = 47 pF
Calculations are for a 12 - 49 MHz crystal with the following parameters:
• shunt capacitance (C0) of 10 pF - 12 pF
• series resistance 40 Ohm
• drive level of 10 µW
If the DSP56374 system clock is an externally supplied square wave voltage source, it is connected to
EXTAL (Figure 2.). When the external square wave source connects to EXTAL, the XTAL pin is not used.
VIH
Midpoint
EXTAL
VIL
ETH
ETL
6
7
8
Note:
ETC
The midpoint is 0.5 (VIH + VIL).
Figure 2. External Clock Timing
Table 19. Clock Operation
No.
6
Characteristics
EXTAL input high
1
Symbol
Min
Max
Units
Eth
3.33
50
ns
Etl
3.33
50
ns
Etc
6.67
inf
ns
50
200
6.67
inf
6.67
13.33
(40% to 60% duty cycle)
7
EXTAL input low2
(40% to 60% duty cycle)
8
EXTAL cycle time
• With PLL disabled
• With PLL enabled
9
Instruction cycle time= ICYC = TC3
• With PLL disabled
• With PLL enabled
Icyc
ns
DSP56374 Data Sheet, Rev. 4.2
30
Freescale Semiconductor
External Clock Operation
Table 19. Clock Operation (continued)
No.
Characteristics
Symbol
Min
Max
Units
Note:
1
Measured at 50% of the input transition.
2
The indicated duty cycle is for the specified maximum frequency for which a part is rated. The
minimum clock high or low time required for correct operation, however, remains the same at lower
operating frequencies; therefore, when a lower clock frequency is used, the signal symmetry may
vary from the specified duty cycle as long as the minimum high time and low time requirements
are met.
3
A valid clock signal must be applied to the EXTAL pin within 3 ms of the DSP56374 being
powered up.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
31
Reset, Stop, Mode Select, and Interrupt Timing
12
Reset, Stop, Mode Select, and Interrupt Timing
Table 20. Reset, Stop, Mode Select, and Interrupt Timing
No.
Characteristics
Expression
Min
Max
Unit
—
—
11
ns
• Power on, external clock generator, PLL disabled
2 xTC
13.4
—
ns
• Power on, external clock generator, PLL enabled
2 x TC
13.4
—
ns
2× TC
13.4
—
ns
(2xTC)+TLOCK
5.0
—
ms
10
Delay from RESET assertion to all pins at reset
value3
11
Required RESET duration4
13
Syn reset deassert delay time
• Minimum
• Maximum (PLL enabled)
14
Mode select setup time
10.0
—
ns
15
Mode select hold time
10.0
—
ns
16
Minimum edge-triggered interrupt request assertion
width
2 xTC
13.4
—
ns
17
Minimum edge-triggered interrupt request
deassertion width
2 xTC
13.4
—
ns
18
Delay from interrupt trigger to interrupt code
execution
10 × TC + 5
72
—
ns
19
Duration of level sensitive IRQA assertion to ensure
interrupt service (when exiting Stop)1, 2, 3
9+(128× TC)
854
—
µs
• PLL is active during Stop and Stop delay is not
enabled
(OMR Bit 6 = 1)
25× TC
165
—
ns
• PLL is not active during Stop and Stop delay is
enabled (OMR Bit 6 = 0)
9+(128xTC) + TLOCK
5.7
ms
• PLL is not active during Stop and Stop delay is
not enabled (OMR Bit 6 = 1)
(25 x TC) + TLOCK
5
ms
• PLL is active during Stop and Stop delay is
enabled
(OMR Bit 6 = 0)
20
• Delay from IRQA, IRQB, IRQC, IRQD, NMI
assertion to general-purpose transfer output
valid caused by first interrupt instruction
execution1
10 x TC + 3.0
69.0
ns
DSP56374 Data Sheet, Rev. 4.2
32
Freescale Semiconductor
Reset, Stop, Mode Select, and Interrupt Timing
Table 20. Reset, Stop, Mode Select, and Interrupt Timing (continued)
No.
21
22
Characteristics
Expression
Min
Max
Unit
• ESAI, ESAI_1, SHI, Timer
12 x TC
—
80.0
ns
• DMA
8 x TC
—
53.0
ns
• IRQ, NMI (edge trigger)
8 x TC
—
53.0
ns
• IRQ (level trigger)
12 x TC
—
80.0
ns
• Data read from ESAI, ESAI_1, SHI
6 x TC
—
40.0
ns
• Data write to ESAI, ESAI_1, SHI
7 x TC
—
46.7
ns
• Timer
2 x TC
—
13.4
ns
• IRQ, NMI (edge trigger)
3 x TC
—
20.0
ns
Interrupt Requests Rate1
DMA Requests Rate
Note:
1 When using fast interrupts and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through
21 apply to prevent multiple interrupt service. To avoid these timing restrictions, the Edge-triggered mode is
recommended when using fast interrupts. Long interrupts are recommended when using Level-sensitive mode.
2
For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time will
be defined by the OMR Bit 6 settings.
For PLL enable, (if bet 12 of the PCTL register is 0), the PLL is shutdown during Stop. Recovering from Stop
requires the PLL to get locked. The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range
of 0.5 ms.
3
Periodically sampled and not 100% tested.
4
RESET duration is measured during the time in which RESET is asserted, VDD is valid, and the EXTAL input is
active and valid. When the VDD is valid, but the other “required RESET duration” conditions (as specified
above) have not been yet met, the device circuitry will be in an uninitialized state that can result in significant
power consumption and heat-up. Designs should minimize this state to the shortest possible duration.
VIH
RESET
11
13
10
All Pins
Reset Value
Figure 3. Reset Timing
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
33
Reset, Stop, Mode Select, and Interrupt Timing
IRQA, IRQB,
IRQC, IRQD,
NMI
19
18
a) First Interrupt Instruction Execution
General
Purpose
I/O
20
IRQA, IRQB,
IRQC, IRQD,
NMI
b) General Purpose I/O
Figure 4. External Fast Interrupt Timing
IRQA, IRQB,
IRQC, IRQD,
NMI
16
IRQA, IRQB,
IRQC, IRQD,
NMI
17
Figure 5. External Interrupt Timing (Negative Edge-Triggered)
VIH
RESET
14
15
MODA, MODB,
MODC, MODD,
PINIT
VIH
VIH
VIL
VIL
IRQA, IRQB,
IRQC,IRQD, NMI
Figure 6. Recovery from Stop State Using IRQA Interrupt Service
DSP56374 Data Sheet, Rev. 4.2
34
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
13
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing
No.
Characteristics1,3,4
Mode
Filter Mode
Expression
Min
Max
Unit
23
Minimum serial clock cycle = tSPICC(min)
Master/Slave
Bypassed
10.0 x TC + 9
76.0
—
ns
Very Narrow
10.0 x TC + 9
76.0
—
ns
Narrow
10.0 x TC + 133
200.0
—
ns
Wide
10.0 x TC + 333
400.0
—
ns
Bypassed
—
—
0
ns
Very Narrow
—
—
10
ns
Narrow
—
—
50
ns
Wide
—
—
100
ns
Bypassed
—
38.0
—
ns
Very Narrow
—
38.0
—
ns
Narrow
—
100.0
—
ns
Wide
—
200.0
—
ns
Bypassed
2.0 x TC + 19.6
33.0
—
ns
Very Narrow
2.0 x TC + 19.6
33.0
—
ns
Narrow
2.0 x TC + 86.6
100.0
—
ns
Wide
2.0 x TC + 186.6
200.0
—
ns
Bypassed
—
38.0
—
ns
Very Narrow
—
38.0
—
ns
Narrow
—
100.0
—
ns
Wide
—
200.0
—
ns
Bypassed
2.0 x TC + 19.6
33.0
—
ns
Very Narrow
2.0 x TC + 19.6
33.0
—
ns
Narrow
2.0 x TC + 86.6
100.0
—
ns
Wide
2.0 x TC + 186.6
200.0
—
ns
Master
—
—
—
—
ns
Slave
—
—
—
5
ns
XX
24
Tolerable Spike width on data or clock in.
Serial clock high period
—
Master
Slave
25
Serial clock low period
Master
Slave
26
Serial clock rise/fall time
—
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
35
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing (continued)
No.
Characteristics1,3,4
Mode
Filter Mode
Expression
Min
Max
Unit
27
SS assertion to first SCK edge
Slave
Bypassed
2.0 x TC + 12.6
26
—
ns
Very Narrow
2.0 x TC + 2.6
16
—
ns
Narrow
2.0 x TC − 37.45
0
—
ns
Wide
2.0 x TC − 87.45
0
—
ns
Bypassed
—
10
—
ns
Very Narrow
—
0
—
ns
Narrow
—
0
—
ns
Wide
—
0
—
ns
Bypassed
—
12
—
ns
Very Narrow
—
22
—
ns
Narrow
—
100
—
ns
Wide
—
200
—
ns
Bypassed
—
0
—
ns
Very Narrow
—
0
—
ns
Narrow
—
0
—
ns
Wide
—
0
—
ns
Bypassed
3.0 x TC
20
—
ns
Very Narrow
3.0 x TC + 23.2
43.2
—
ns
Narrow
3.0 x TC + 53.2
73.2
—
ns
Wide
3.0 x TC + 80
100.0
—
ns
CPHA = 0
CPHA = 1
28
29
30
Slave
Last SCK edge to SS not asserted
Slave
Data input valid to SCK edge (data input
set-up time)
SCK last sampling edge to data input not
valid
Master
/Slave
Master
/Slave
31
SS assertion to data out active
Slave
—
—
5
—
ns
32
SS deassertion to data high impedance2
Slave
—
—
—
9
ns
33
SCK edge to data out valid
(data out delay time)
Master
/Slave
Bypassed
3.0 x TC + 26.1
—
46.2
ns
Very Narrow
3.0 x TC + 90.4
—
110.4
ns
Narrow
3.0 x TC + 116.4
—
136.4
ns
Wide
3.0 x TC + 203.4
—
223.4
ns
Bypassed
2.0 x TC
13.4
—
ns
Very Narrow
2.0 x TC + 1.6
15
—
ns
Narrow
2.0 x TC + 41.6
55
—
ns
Wide
2.0 x TC + 91.6
105
—
ns
—
—
—
12.0
ns
34
35
SCK edge to data out not valid
(data out hold time)
SS assertion to data out valid
(CPHA = 0)
Master
/Slave
Slave
DSP56374 Data Sheet, Rev. 4.2
36
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
Table 21. Serial Host Interface SPI Protocol Timing (continued)
No.
36
37
Characteristics1,3,4
SCK edge following the first SCK
sampling edge to HREQ output
deassertion
Last SCK sampling edge to HREQ output
not deasserted (CPHA = 1)
Mode
Filter Mode
Expression
Min
Max
Unit
Slave
Bypassed
3.0 x TC + 30
50
—
ns
Very Narrow
3.0 x TC + 40
60
—
ns
Narrow
3.0 x TC + 80
100
—
ns
Wide
3.0 x TC + 120
150
—
ns
Bypassed
4.0 x TC
57.0
—
ns
Very Narrow
4.0 x TC
67.0
—
ns
Narrow
4.0 x TC
107.0
—
ns
Wide
4.0 x TC
157.0
—
ns
Slave
38
SS deassertion to HREQ output not
deasserted (CPHA = 0)
Slave
—
3.0 x TC + 30
50.0
—
ns
39
SS deassertion pulse width (CPHA = 0)
Slave
—
2.0 x TC
13.4
—
ns
40
HREQ in assertion to first SCK edge
Master
Bypassed
0.5 x TSPICC +
3.0 x TC + 5
63
—
ns
Very Narrow
0.5 x TSPICC +
3.0 x TC + 5
63
—
ns
Narrow
0.5 x TSPICC +
3.0 x TC + 5
125
—
ns
Wide
0.5 x TSPICC +
3.0 x TC + 5
225
—
ns
41
HREQ in deassertion to last SCK
sampling edge (HREQ in set-up time)
(CPHA = 1)
Master
—
—
0
—
ns
42
First SCK edge to HREQ in not asserted
(HREQ in hold time)
Master
—
—
0
—
ns
43
HREQ assertion width
Master
—
3.0 x TC
20
—
ns
Note:
1 V
CORE_VDD = 1.2 5 ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
2 Periodically sampled, not 100% tested
3 All times assume noise free inputs.
4 All times assume internal clock frequency of 150 MHz.
5 Equation applies when the result is positive T .
C
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
37
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
26
SCK (CPOL = 0)
(Output)
23
24
26
25
26
SCK (CPOL = 1)
(Output)
29
30
MISO
(Input)
30
29
MSB
Valid
LSB
Valid
34
33
MOSI
(Output)
MSB
LSB
40
42
HREQ
(Input)
43
Figure 7. SPI Master Timing (CPHA = 0)
DSP56374 Data Sheet, Rev. 4.2
38
Freescale Semiconductor
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
26
SCK (CPOL = 0)
(Output)
24
23
26
25
26
SCK (CPOL = 1)
(Output)
29
29
30
MISO
(Input)
30
MSB
Valid
LSB
Valid
33
MOSI
(Output)
34
MSB
LSB
40
41
42
HREQ
(Input)
43
Figure 8. SPI Master Timing (CPHA = 1)
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
39
Serial Host Interface SPI Protocol Timing
SS
(Input)
25
23
24
26
28
26
39
SCK (CPOL = 0)
(Input)
27
23
24
26
25
26
SCK (CPOL = 1)
(Input)
35
33
34
31
MISO
(Output)
34
32
MSB
LSB
29
29
30
MOSI
(Input)
MSB
Valid
30
LSB
Valid
36
38
HREQ
(Output)
Figure 9. SPI Slave Timing (CPHA = 0)
DSP56374 Data Sheet, Rev. 4.2
40
Freescale Semiconductor
Serial Host Interface (SHI) I2C Protocol Timing
SS
(Input)
25
23
24
26
28
26
SCK (CPOL = 0)
(Input)
27
24
26
25
26
SCK (CPOL = 1)
(Input)
33
33
34
32
31
MISO
(Output)
MSB
LSB
29
29
30
30
MSB
Valid
MOSI
(Input)
LSB
Valid
37
36
HREQ
(Output)
Figure 10. SPI Slave Timing (CPHA = 1)
Serial Host Interface (SHI) I2C Protocol Timing
14
Table 22. SHI I2C Protocol Timing
Standard I2C
No.
XX
Symbol/
Expression
Characteristics1,2,3,4,5
Standard
Fast-Mode
Unit
Min
Max
Min
Max
Filters Bypassed
—
0
—
0
ns
Very Narrow Filters enabled
—
10
—
10
ns
Narrow Filters enabled
—
50
—
50
ns
Wide Fileters enabled.
—
100
—
100
ns
Tolerable Spike Width on SCL or SDA
—
44
SCL clock frequency
FSCL
—
100
—
400
kHz
44
SCL clock cycle
TSCL
10
—
2.5
—
µs
45
Bus free time
TBUF
4.7
—
1.3
—
µs
46
Start condition set-up time
TSUSTA
4.7
—
0.6
—
µs
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
41
Serial Host Interface (SHI) I2C Protocol Timing
Table 22. SHI I2C Protocol Timing (continued)
Standard I2C
No.
Symbol/
Expression
Characteristics1,2,3,4,5
Standard
Fast-Mode
Unit
Min
Max
Min
Max
THD;STA
4.0
—
0.6
—
µs
47
Start condition hold time
48
SCL low period
TLOW
4.7
—
1.3
—
µs
49
SCL high period
THIGH
4.0
—
1.3
—
µs
50
SCL and SDA rise time
TR
—
5.0
—
5.0
ns
51
SCL and SDA fall time
TF
—
5.0
—
5.0
ns
52
Data set-up time
TSU;DAT
250
—
100
—
ns
53
Data hold time
THD;DAT
0.0
—
0.0
0.9
µs
54
DSP clock frequency
• Filters bypassed
10.6
—
28.5
—
MHz
• Very Narrrow filters enabled
10.6
—
28.5
—
MHz
• Narrow filters enabled
11.8
—
39.7
—
MHz
• Wide filters enabled
13.1
—
61.0
—
MHz
FOSC
55
SCL low to data out valid
TVD;DAT
—
3.4
—
0.9
µs
56
Stop condition setup time
TSU;STO
4.0
—
0.6
—
µs
57
HREQ in deassertion to last SCL edge
(HREQ in set-up time)
tSU;RQI
0.0
—
0.0
—
ns
58
First SCL sampling edge to HREQ output
deassertion2
—
57.0
—
57.0
ns
—
77.0
—
67.0
ns
—
157.0
—
157.0
ns
—
257.0
—
257.0
ns
44
—
44
—
ns
54
—
54
—
ns
94
—
94
—
ns
144
—
144
—
ns
• Filters bypassed
4327
—
927
—
ns
• Very Narrow filters enabled
4317
—
917
—
ns
• Narrow filters enabled
4282
—
877
—
ns
• Wide filters enabled
4227
—
827
—
ns
0.0
—
0.0
—
ns
• Filters bypassed
• Very Narrow filters enabled
• Wide filters enabled
Last SCL edge to HREQ output not
deasserted2
• Filters bypassed
• Very Narrow filters enabled
• Wide filters enabled
61
TAS;RQO
2 × TC + 30
2 × TC + 40
2 × TC + 80
2 × TC + 130
• Narrow filters enabled
60
4 × TC + 30
4 × TC + 50
4 × TC + 130
4 × TC + 230
• Narrow filters enabled
59
TNG;RQO
HREQ in assertion to first SCL edge
First SCL edge to HREQ is not asserted
(HREQ in hold time.)
TAS;RQI
tHO;RQI
DSP56374 Data Sheet, Rev. 4.2
42
Freescale Semiconductor
Programming the Serial Clock
Table 22. SHI I2C Protocol Timing (continued)
Standard I2C
No.
Symbol/
Expression
Characteristics1,2,3,4,5
Standard
Min
Max
Fast-Mode
Min
Unit
Max
Note:
1
VCORE_VDD = 1.2 5 ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
2
Pull-up resistor: R P (min) = 1.5 kOhm
3
Capacitive load: C b (max) = 50 pF
4
All times assume noise free inputs
5
All times assume internal clock frequency of 150MHz
15
Programming the Serial Clock
The programmed serial clock cycle, T I CCP, is specified by the value of the HDM[7:0] and HRS bits of the
HCKR (SHI clock control register).
2
The expression for T I CCP is
2
T I2CCP = [TC × 2 × (HDM[7:0] + 1) × (7 × (1 – HRS) + 1)]
Eqn. 1
where
— HRS is the prescaler rate select bit. When HRS is cleared, the fixed
divide-by-eight prescaler is operational. When HRS is set, the prescaler is bypassed.
— HDM[7:0] are the divider modulus select bits. A divide ratio from 1 to 256 (HDM[7:0] = $00
to $FF) may be selected.
In I2C mode, the user may select a value for the programmed serial clock cycle from
6 × TC (if HDM[7:0] = $02 and HRS = 1)
Eqn. 2
4096 × TC (if HDM[7:0] = $FF and HRS = 0)
Eqn. 3
to
The programmed serial clock cycle (TI CCP ) should be chosen in order to achieve the desired SCL serial
clock cycle (TSCL), as shown in Table 23.
2
Table 23. SCL Serial Clock Cycle (TSCL) Generated as Master
Nominal
TI2CCP + 3 × TC + 45ns + TR
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
43
Enhanced Serial Audio Interface Timing
44
46
49
48
SCL
50
53
51
45
52
SDA
MSB
Stop Start
47
LSB
58
61
ACK
Stop
55
56
57
60
59
HREQ
Figure 11. I2C Timing
16
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing
Characteristics1, 2, 3
No.
62
63
64
65
66
Clock
cycle5
Clock high period
Expression3
Min
Max
Condition4
Unit
tSSICC
4 × Tc
26.4
—
x ck
ns
4 × Tc
26.4
—
i ck
ns
tSSICCH
• For internal clock
2 × Tc − 0.5
12.8
—
• For external clock
2 × Tc
13.4
—
• For internal clock
2 × Tc
13.4
—
• For external clock
2 × Tc
13.4
—
—
—
17.0
x ck
—
7.0
i ck a
—
17.0
x ck
—
7.0
i ck a
—
19.0
x ck
—
9.0
i ck a
—
19.0
x ck
—
9.0
i ck a
—
16.0
x ck
—
6.0
i ck a
Clock low period
tSSICCL
SCKR edge to FSR out (bl) high
—
SCKR edge to FSR out (bl) low
—
6
67
SCKR edge to FSR out (wr) high
68
low6
69
Symbol
SCKR edge to FSR out (wr)
SCKR edge to FSR out (wl) high
—
—
—
ns
—
—
—
—
ns
ns
ns
ns
ns
DSP56374 Data Sheet, Rev. 4.2
44
Freescale Semiconductor
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing (continued)
No.
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
Characteristics1, 2, 3
SCKR edge to FSR out (wl) low
Symbol
Expression3
Min
Max
Condition4
Unit
—
—
—
17.0
x ck
ns
—
7.0
i ck a
12.0
—
x ck
19.0
—
i ck
3.5
—
x ck
9.0
—
i ck
2.0
—
x ck
12.0
—
i ck a
2.0
—
x ck
12.0
—
i ck a
2.5
—
x ck
8.5
—
i ck a
0.0
—
x ck
19.0
—
i ck s
6.0
—
x ck
0.0
—
i ck s
—
18.0
x ck
—
8.0
i ck
—
20.0
x ck
—
10.0
i ck
—
20.0
x ck
—
10.0
i ck
—
22.0
x ck
—
12.0
i ck
—
19.0
x ck
—
9.0
i ck
—
20.0
x ck
—
10.0
i ck
—
22.0
x ck
—
17.0
i ck
—
17.0
x ck
—
11.0
i ck
—
18.0
x ck
—
13.0
i ck
—
21.0
x ck
—
16.0
i ck
Data in setup time before SCKR (SCK in
synchronous mode) edge
—
Data in hold time after SCKR edge
—
FSR input (bl, wr) high before SCKR edge 6
FSR input (wl) high before SCKR edge
—
—
FSR input hold time after SCKR edge
—
Flags input setup before SCKR edge
—
Flags input hold time after SCKR edge
—
SCKT edge to FST out (bl) high
—
SCKT edge to FST out (bl) low
—
SCKT edge to FST out (wr) high6
—
6
—
SCKT edge to FST out (wr) low
SCKT edge to FST out (wl) high
—
SCKT edge to FST out (wl) low
—
SCKT edge to data out enable from high
impedance
—
SCKT edge to transmitter #0 drive enable
assertion
—
SCKT edge to data out valid
—
SCKT edge to data out high impedance
7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
45
Enhanced Serial Audio Interface Timing
Table 24. Enhanced Serial Audio Interface Timing (continued)
No.
88
89
90
91
Characteristics1, 2, 3
Symbol
Expression3
Min
Max
Condition4
Unit
SCKT edge to transmitter #0 drive enable
deassertion7
—
—
—
14.0
x ck
ns
—
9.0
i ck
FST input (bl, wr) setup time before SCKT
edge6
—
2.0
—
x ck
18.0
—
i ck
FST input (wl) setup time before SCKT
edge
—
2.0
—
x ck
18.0
—
i ck
FST input hold time after SCKT edge
—
4.0
—
x ck
5.0
—
i ck
—
—
—
ns
ns
ns
92
FST input (wl) to data out enable from high
impedance
—
—
—
21.0
—
ns
93
FST input (wl) to transmitter #0 drive enable
assertion
—
—
—
14.0
—
ns
94
Flag output valid after SCKT rising edge
—
—
—
14.0
x ck
ns
—
9.0
i ck
95
HCKR/HCKT clock cycle
—
2 x TC
13.4
—
ns
96
HCKT input edge to SCKT output
—
—
—
18.0
ns
97
HCKR input edge to SCKR output
—
—
—
18.0
ns
Note:
1 V
CORE_VDD = 1.25 ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
2 i ck = internal clock
x ck = external clock
i ck a = internal clock, asynchronous mode
(asynchronous implies that SCKT and SCKR are two different clocks)
i ck s = internal clock, synchronous mode
(synchronous implies that SCKT and SCKR are the same clock)
3 bl = bit length
wl = word length
wr = word length relative
4 SCKT(SCKT pin) = transmit clock
SCKR(SCKR pin) = receive clock
FST(FST pin) = transmit frame sync
FSR(FSR pin) = receive frame sync
HCKT(HCKT pin) = transmit high frequency clock
HCKR(HCKR pin) = receive high frequency clock
5 For the internal clock, the external clock cycle is defined by Icyc and the ESAI control register.
6 The word-relative frame sync signal waveform relative to the clock operates in the same manner as the bit-length frame
sync signal waveform, but spreads from one serial clock before first bit clock (same as bit length frame sync signal), until
the one before last bit clock of the first word in frame.
7 Periodically sampled and not 100% tested.
8 ESAI_1 specs match those of ESAI.
DSP56374 Data Sheet, Rev. 4.2
46
Freescale Semiconductor
Enhanced Serial Audio Interface Timing
62
SCKT
(Input/Output)
63
64
78
79
FST (Bit) Out
83
84
FST (Word) Out
87
87
85
88
Data Out
First Bit
Last Bit
92
Transmitter #0
Drive Enable
90
86
89
94
FST (Bit) In
91
94
93
FST (Word) In
95
See Note
Flags Out
Note:
In network mode, output flag transitions can occur at the start of each time slot within the
frame. In normal mode, the output flag state is asserted for the entire frame period.
Figure 12 is drawn assuming positive polarity bit clock (TCKP=0) and positive frame sync
polarity (TFSP=0).
Figure 12. ESAI Transmitter Timing
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
47
Enhanced Serial Audio Interface Timing
62
63
64
SCKR
(Input/Output)
65
66
FSR (Bit)
Out
69
70
FSR (Word)
Out
72
71
Data In
First Bit
Last Bit
75
73
FSR (Bit)
In
74
FSR (Word)
In
75
76
77
Flags In
Note:
Figure 13 is drawn assuming positive polarity bit clock (RCKP=0) and positive frame sync polarity
(RFSP=0).
Figure 13. ESAI Receiver Timing
DSP56374 Data Sheet, Rev. 4.2
48
Freescale Semiconductor
Timer Timing
HCKT
SCKT (output)
95
96
Note: Figure 14 is drawn assuming positive polarity high frequency clock (THCKP=0) and positive bit clock polarity (TCKP=0).
Figure 14. ESAI HCKT Timing
HCKR
SCKR (output)
95
97
Note: Figure 15 is drawn assuming positive polarity high frequency clock (RHCKP=0) and positive bit clock polarity (RCKP=0).
Figure 15. ESAI HCKR Timing
17
Timer Timing
Table 25. Timer Timing
150 MHz
No.
Characteristics
Expression
Unit
Min
Max
98
TIO Low
2 × TC + 2.0
15.4
—
ns
99
TIO High
2 × TC + 2.0
15.4
—
ns
Note: VCORE_VDD = 1.25 V ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
TIO
98
99
Figure 16. TIO Timer Event Input Restrictions
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
49
GPIO Timing
18
GPIO Timing
Table 26. GPIO Timing
Characteristics1
No.
100
Expression
EXTAL edge to GPIO out valid (GPIO out delay time)2
101
EXTAL edge to GPIO out not valid (GPIO out hold time)
102
GPIO In valid to EXTAL edge (GPIO in set-up time)2
2
Min
Max
Unit
—
7
ns
—
7
ns
2
—
ns
0
—
ns
2
103
EXTAL edge to GPIO in not valid (GPIO in hold time)
104
Minimum GPIO pulse high width
TC + 13
19.7
—
ns
105
Minimum GPIO pulse low width
TC + 13
19.7
—
ns
106
GPIO out rise time
—
—
13.0
ns
107
GPIO out fall time
—
—
13.0
ns
Note:
1 V
CORE_VDD = 1.25 V ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
2 PLL Disabled, EXTAL driven by a square wave.
EXTAL
100
101
GPIO
(Output)
102
GPIO
(Input)
103
Valid
GPIO
(Output)
104
106
105
107
Figure 17. GPIO Timing
19
JTAG Timing
Table 27. JTAG Timing
All frequencies
No.
108
Characteristics
TCK frequency of operation (1/(TC × 3); maximum 10 MHz)
Unit
Min
Max
—
10.0
MHz
DSP56374 Data Sheet, Rev. 4.2
50
Freescale Semiconductor
JTAG Timing
Table 27. JTAG Timing (continued)
All frequencies
No.
Characteristics
Unit
Min
Max
109
TCK cycle time in Crystal mode
100.0
—
ns
110
TCK clock pulse width measured at 1.65 V
50.0
—
ns
111
TCK rise and fall times
—
3.0
ns
112
Boundary scan input data setup time
15.0
—
ns
113
Boundary scan input data hold time
24.0
—
ns
114
TCK low to output data valid
—
40.0
ns
115
TCK low to output high impedance
—
40.0
ns
116
TMS, TDI data setup time
5.0
—
ns
117
TMS, TDI data hold time
25.0
—
ns
118
TCK low to TDO data valid
—
44.0
ns
119
TCK low to TDO high impedance
—
44.0
ns
Note:
1. VCORE_VDD = 1.25 V ± 0.05 V; TJ = -40°C to 110°C (52 LQFP) / -40°C to 105°C (80 LQFP), CL = 50 pF
2. All timings apply to OnCE module data transfers because it uses the JTAG port as an interface.
109
TCK
(Input)
VIH
110
110
VM
VM
VIL
111
111
Figure 18. Test Clock Input Timing Diagram
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
51
JTAG Timing
TCK
(Input)
VIH
VIL
112
Data
Inputs
113
Input Data Valid
114
Data
Outputs
Output Data Valid
115
Data
Outputs
114
Data
Outputs
Output Data Valid
Figure 19. Debugger Port Timing Diagram
TCK
(Input)
VIH
VIL
116
TDI
TMS
(Input)
117
Input Data Valid
118
TDO
(Output)
Output Data Valid
119
TDO
(Output)
118
TDO
(Output)
Output Data Valid
Figure 20. Test Access Port Timing Diagram
DSP56374 Data Sheet, Rev. 4.2
52
Freescale Semiconductor
Watchdog Timer Timing
20
Watchdog Timer Timing
Table 28. Watchdog Timer Timing
No.
Characteristics
Expression
Min
Max
Unit
120
Delay from time-out to fall of TIO1
2 × Tc
13.4
—
ns
121
Delay from timer clear to rise of TIO1
2 x Tc
13.4
—
ns
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
53
Watchdog Timer Timing
Appendix A
Package Information
SCKT_1_PE3
HCKR_1_PE2
HCKR_PC2
HCKT_PC5
HCKT_1_PE5
SCAN
IO_Vdd
65
64
63
62
61
SCKR_1_PE0
70
66
Core_Gnd
71
67
Core_Vdd
72
SCKR_PC0
GPIO_PG14
73
SCKT_PC3
FST_1_PE4
74
68
FST_PC4
75
69
FSR_1_PE1
FSR_PC1
SDO4_PC7
78
76
SDO5_PC6
79
77
IO_Gnd
80
DSP56374 Pinout
SCK_SCL
15
46
XTAL
MISO_SDA
16
45
EXTAL
MOSI_HA0
17
44
PLLD_Vdd
GPIO_PG8
18
43
PLLD_Gnd
GPIO_PG7
19
42
PLLP_Gnd
IO_Gnd
20
41
PLLP_Vdd
40
IO_Vdd
PLLA_Gnd
47
39
14
PLLA_Vdd
PINIT_NMI
SS_HA2
38
SDO0_1_PE11
48
37
49
13
GPIO_PG0
12
HREQ_PH4
GPIO_PG1
GPIO_PG9
36
SDO1_1_PE10
35
50
GPIO_PG2
11
RESET_B
Core_Gnd
GPIO_PG10
34
51
GPIO_PG3
10
33
Core_Vdd
Core_Gnd
Core_Gnd
52
32
9
Core_Vdd
SDO2_1_PE9
Core_Vdd
31
53
PLOCK/TIO2
8
30
SDO3_1_PE8
GPIO_PG11
WDT/TIO1
54
29
7
TIO00
SDO0_PC11
MODD_IRQD_PH3
28
55
27
6
GPIO_PG4
SDO1_PC10
MODC_IRQC_PH2
TCK
SDO2_PC9
56
26
57
5
TMS
4
GPIO_PG12
25
GPIO_PG13
TDI
SDO3_PC8
24
58
TDO
3
23
SDO4_1_PE7
MODB_IRQB_PH1
22
59
GPIO_PG5
60
2
21
1
MODA_IRQA_PH0
GPIO_PG6
IO_Vdd
IO_Vdd
A.1
SDO5_1_PE6
1.25 V
Filter
3.3 V
Figure A-1. 80-Pin Vdd Connections
DSP56374 Data Sheet, Rev. 4.2
54
Freescale Semiconductor
HCKT_PC5
SCAN
IO_Vdd
42
41
40
26
HCKR_PC2
43
PLLA_Gnd
SCKR_PC0
SCKT_PC3
Core_Gnd
46
44
FST_PC4
FSR_PC1
Core_Vdd
SDO4_PC7
49
47
SDO5_PC6
50
48
IO_Gnd
51
45
25
13
PLLA_Vdd
12
IO_Gnd
23
MOSI_HA0
24
11
RESET_B
MISO_SDA
Core_Gnd
10
22
SCK_SCL
Core_Vdd
9
21
SS_HA2
20
8
PLOCK/TIO2
HREQ_PH4
WDT/TIO1
7
19
Core_Gnd
TIO00
6
18
Core_Vdd
TCK
5
17
MODD_IRQD_PH3
TMS
4
16
MODC_IRQC_PH2
TDI
3
15
MODB_IRQB_PH1
14
2
TDO
1
MODA_IRQA_PH0
IO_Vdd
IO_Vdd
52
Watchdog Timer Timing
39
SDO3_PC8
38
SDO2_PC9
37
SDO1_PC10
36
SDO0_PC11
35
Core_Vdd
34
Core_Gnd
33
PINIT_NMI
32
XTAL
31
EXTAL
30
PLLD_Vdd
29
PLLD_Gnd
28
PLLP_Gnd
27
PLLP_Vdd
1.25 V
Filter
3.3 V
Figure A-2. 52-pin Vdd Connections
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
55
Watchdog Timer Timing
A.2
A.2.1
Package Information
80-Pin Package
.
DSP56374 Data Sheet, Rev. 4.2
56
Freescale Semiconductor
Watchdog Timer Timing
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
57
Watchdog Timer Timing
DSP56374 Data Sheet, Rev. 4.2
58
Freescale Semiconductor
Watchdog Timer Timing
.
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
59
Watchdog Timer Timing
A.2.2
52-Pin Package
DSP56374 Data Sheet, Rev. 4.2
60
Freescale Semiconductor
Watchdog Timer Timing
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
61
Watchdog Timer Timing
DSP56374 Data Sheet, Rev. 4.2
62
Freescale Semiconductor
Watchdog Timer Timing
DSP56374 Data Sheet, Rev. 4.2
Freescale Semiconductor
63
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
DSP56374
Rev. 4.2, 1/2007
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2004, 2005, 2006, 2007. All rights reserved.