MACOM 5787395-5

AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Cable Assemblies, Series III
AMPLIMITE .050 Series
Connectors, Series III
To meet Standard
Applications the following
106 ohm, black jacketed
cable assemblies are available. For AMPLIMITE .050
Series cable assemblies that
meet other impedance
requirements or other
lengths consult TE.
SCSI-2
SCSI-1 to SCSI-2
RS-232 (Alternate)
to RS-232
RS-232 (Alternate)
IPI-2 and HIPPI
2 Feet
Part Numbers
2 Meters
3 Meters
SCSI-2
50 pos. .050 Series Plug to
50 pos. .050 Series Plug
750254-1
5750254-2
750254-3
SCSI-2*
68 pos. .050 Series Plug to
68 pos. .050 Series Plug
—
5750732-2
5750732-4
RS-232
(Alternate)
26 pos. .050 Series Plug to
26 pos. .050 Series Plug
—
750255-2
750255-3
Application
Assembly
5 Meters
Part Numbers
15 Meters
25 Meters
IPI-2 and
HIPPI
100 pos. .050 Series Plug to
100 pos. .050 Series Plug
749755-2
—
—
Application
Assembly
*This version has spring latches. Consult TE for availability of jackscrew version.
Note: .050 centerline ribbon cable assemblies are available in single or double ended versions. These assemblies are
made using AMPLIMITE .050 Series panel mount connectors, AMPLIMITE .050 Series all-plastic connectors
and AMP-LATCH Novo receptacles. Consult TE.
SCSI—Small Computer Systems Interface
HIPPI—High Performance Parallel Interface
IPI—Intelligent Peripheral Interface
Note: All part numbers are RoHS compliant.
6
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Right-Angle Receptacle Headers, Series III
.463
[11.76]
AMPLIMITE .050 Series
Connectors, Series III
.118±.003
[3.00±0.08]
K
Materials:
G
E
Housing — Thermoplastic, 94V-0
rated, black. SMT compatible
Shell — Steel, plated bright nickel over
copper
Bracket — Zinc, plated nickel over
copper
Contacts — Phosphor bronze, duplex
plated [.000030] 0.00076 min. gold on
mating end; tin on solder end; all underplated nickel
Position 1
F
.050 Typ.
[1.27]
.100
[2.54]
Typ.
.406
[10.31]
2-56 UNC 2B
Holes
Last Position
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Technical Documents:
Product Specifications — 108-1228
Application Specifications —
114-40029
Shown With Boardlocks
No. of
Pos.
40
50
50
68
100
E
1.580
40.13
1.830
46.48
1.830
46.48
2.280
57.91
3.080
78.23
Dimensions
F
G
.950
24.13
1.200
30.48
1.200
30.48
1.650
41.91
2.450
62.23
1.815
46.10
2.065
52.45
2.065
52.45
2.515
63.88
3.315
84.20
K
1.415
35.94
1.665
42.29
1.665
42.29
2.115
53.72
2.915
74.04
w/ Rails and Latchblocks
With .100 [2.54]
Solder Tails
Without
With
Boardlocks
Boardlocks
Shown With Boardlocks
Part Numbers
w/o Rails, w/ Latchblocks
With .100 [2.54]
Solder Tails
Without
With
Boardlocks
Boardlocks
Shown With Boardlocks
w/o Rails, w/o Latchblocks
With .100 [2.54]
With .120 [3.05]
Solder Tails
Solder Tails
Without
With
With
Boardlocks
Boardlocks
Boardlocks
—
1761028-2
—
5787082-3
—
5787170-4*
—
5787190-5
1761028-3
5787394-5
5787082-5
—
5787170-5*
5787362-5*
—
5787266-5*
—
5787395-5*
—
—
—
5787190-7
1761028-4
5787394-7
5787082-7
5787169-7* 5787170-7*
5787362-7*
—
1761028-5
—
5787082-9
5787169-9* 5787170-9*
5787362-9*
*Has 4-40 threaded mating holes (2 places), for use with female screwlock Part No. 750644-1.
Note: All part numbers are RoHS compliant.
7
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Vertical Receptacle Headers With
Through-Hole Tails, Series III
L
P
AMPLIMITE .050 Series
Connectors, Series III
Position 1
Position 2
Position 3
.406
[10.31]
Materials:
Housing—Thermoplastic, 94V-0 rated,
black. SMT compatible
Shell—Steel, plated bright nickel over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end; tin on solder end; all underplated nickel
.350
[8.89]
.100
[2.54]
2-56 Threaded
Hole 2 Plc.
Last Position
R
M
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
.125±.015
[3.18±0.38]
.351
[8.92]
.150
[3.81]
Note: Extra pin contact protection is provided
by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion
should not be used to disengage the connector
system.
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Part Number 749069-5
No. of
Pos.
20
26
28
40
50
68
80
100
L
1.080
27.43
1.230
31.34
1.280
32.51
1.580
40.13
1.830
46.48
2.280
57.91
2.580
65.53
3.080
78.23
Part Number 749721-5
Dimensions
M
P
.915
.450
23.24
11.43
1.065
.600
27.05
15.24
1.115
.650
28.32
16.51
1.415
.950
35.94
24.13
1.665
1.200
42.29
30.48
2.115
1.650
53.72
41.91
2.415
1.950
61.34
49.53
2.915
2.450
74.04
62.23
R
1.315
33.40
1.465
37.21
1.515
38.48
1.815
46.10
2.065
52.45
2.515
63.88
2.815
71.50
3.315
84.20
Part Number 749070-7
w/ Rails & Latchblocks
Part Numbers
w/ Latchblocks
Plain
5749069-1
—
—
5749069-2
—
—
—
5749721-3
—
5749069-4
—
—
5749069-5
5749721-5
5749070-5
5749069-7
5749721-7
5749070-7
5749069-8
—
—
5749069-9
—
5749070-9
Note: All part numbers are RoHS compliant.
8
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Vertical Receptacle Headers With
Through-Hole Tails, Series III (Continued)
.120 [3.05] Solder Tail
Length
A
D
.763
[19.38]
Typ.
Position 1
Typ.
2-56UNC-2B
4 Holes
AMPLIMITE .050 Series
Connectors, Series III
.050
[1.27]
Typ.
±.008
B [±0.20]
C
Last Position
Typ.
.120±.007
[3.05±0.18]
Typ.
E
Rails and Latch Blocks
Materials:
Housing—Thermoplastic, 94V-0 rated,
black. SMT compatible
Shell—Steel, plated bright nickel over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end; tin on solder end; all underplated nickel
A
D
.050
[1.27]
Typ.
.763
[19.38]
Typ.
Position 1
Typ.
4-40UNC-2B
4 Holes
±.008
B [±0.20]
C
Related Product Data:
Required Hardware—page 26
Last Position
Typ.
.120±.007
[3.05±0.18]
Typ.
E
Technical Documents:
Flat Top Configuration
Product Specifications—108-1228-1
Application Specifications—
114-40029
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Note: Extra pin contact protection is provided
by rails, which facilitate a straight-out unmating motion. A side-to-side rocking motion
should not be used to disengage the connector
system.
No. of
Pos.
A
2.085
52.96
2.535
64.39
2.535
64.39
50/50
68/68
68/68
B
.874
22.20
1.124
28.55
1.124
28.55
Dimensions
C
.500
12.70
.750
19.05
.750
19.05
D
1.830
46.48
2.280
57.91
2.280
57.91
E
1.200
30.48
1.650
41.91
1.650
41.91
Part No.
5787656-1
5787678-1
*5787679-1*
*Flat-top configuration.
Note: All part numbers are RoHS compliant.
9
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Vertical Receptacle Headers, Series III, with
ACTION PIN Contacts (.050 x .100 [1.27 x 2.54] Centerlines)
Product Facts
AMPLIMITE .050 Series
Connectors, Series III
■
Recognized under the
Component Program of
the Underwriters
Laboratories, Inc.,
File No. E28476
R
■
■
Certified by Canadian
Standards
Association,
File No. 1088108
(LR 7189A-207)
R
Produced under a Quality
Management System
certified to ISO 9001
■ A copy of the
certificate is available
upon request
ISO900e1d
i
rtif
Ce
Shielded AMPLIMITE .050
Series headers with
ACTION PIN contacts offer
a high-density D type
interface, and a solderless
board-mount interconnection.
These vertical mount
headers are available in
20, 26, 50, 68 and 100
contact sizes. Choice of
configurations includes;
headers with rails and latch
blocks, with latch blocks
only, and without rails and
latch blocks.
ACTION PIN contact tails
are available in two lengths;
.173 [4.39] for pc boards
with a nominal thickness of
.062 [1.56] to .093 [2.36],
and .280 [7.11] for pc
boards with a nominal
thickness of .125 [3.18]
to .200 [5.08].
AMPLIMITE .050 Series
headers with ACTION PIN
contacts are compatible
with SCSI-2, SCSI-3, EIA
RS-232, IPI-2 and HIPPI
standards.
Principle of the AMPLIMITE .050
Series Compliant ACTION PIN
Contact
When an AMPLIMITE .050
Series compliant
ACTION PIN contact is
inserted into a platedthrough-hole, two spring
members are compressed,
exerting force against
the hole for a gas-tight
connection. The diameter
of the hole is smaller than
the diagonal size of the pin.
AMPLIMITE .050 Series
compliant ACTION PIN
contact, the residual force
of the elastic deformation
maintains stored energy to
produce a gas-tight contact
zone between the pin and
the plated-through-hole.
This ensures long term
electrical and mechanical
reliability of the
interconnection.
Technical Documents:
Product Specification—
108-1228-2
Application Specification—
114-40029
Instruction Sheets—
408 6923—AMP Manual Arbor
Frame Assembly
408 9027—AMP Adapter Kit for
Greenerd Frame Assemblies 3A and 3B
408 9757—Seating Instructions
and Tooling
408 6927—Recommendations for
pc board support
The beam characteristics of
the pin are designed so that
a plastic, as well as an
elastic, deformation takes
place during insertion.
The two spring members
compress to different
degrees to accommodate
hole tolerances. The
compliant pin also reduces
strain on the board. With a
rigid pin, the elastic strain
energy is stored entirely in
the board, leading to
damage of the platedthrough holes. With the
10
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Vertical Receptacle Headers,
with ACTION PIN Tails, Series III
P
Position 2
Position 1
AMPLIMITE .050 Series
Connectors, Series III
2-56 Thread
2 Plc.
.406
[10.31]
Last Position
L
Materials:
Housings—Thermoplastic, 94V-0
rated, black, SMT compatible
Shell—Carbon steel, plated bright tin
over copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end; tin on solder end; all underplated nickel
.350
[8.89]
Typ.
R
.275
[2.98]
Typ.
M Typ.
Mating Face
.351
[8.92] Typ.
±.015
S ±0.38
[
]
.150
[3.81]
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Technical Documents:
Product Specifications—
108-1228-2
Application Specifications—
114-40029
Note: Extra pin contact protection is provided
by rails, which facilitate a straight-out unmating motion. A side-to-side rocking motion
should not be used to disengage the connector
system.
Part Number 786554-1
No. of
Pos.
20
26
50
68
100
120
Part Number 786554-7
L
1.080
27.43
1.230
31.34
M
.915
23.24
1.065
27.05
Dimensions
P
.450
11.43
.600
15.24
R
1.315
33.40
1.465
37.21
1.830
46.48
1.665
42.29
1.200
30.48
2.065
52.45
2.280
57.91
2.115
53.72
1.650
41.91
2.515
63.88
3.080
78.23
3.580
90.93
2.915
74.04
3.415
86.74
2.450
62.23
2.950
74.93
3.315
84.20
3.815
96.90
S
.173
4.39
.173
4.39
.173
4.39
.280
7.11
.173
4.39
.280
7.11
.173
4.39
.173
4.39
Part Number 786155-7
w/ Rails & Latchblocks
Part Numbers
w/ Latchblocks
Plain
5786554-1
—
—
5786554-2
—
—
5786554-5
5786155-5
5786555-5
5786556-5
—
—
5786554-7
5786155-7
5786555-7
786155-7
5786557-7
5786554-9
—
5786555-9
1-5786554-0
—
—
—
Note: All part numbers are RoHS compliant.
11
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Cable Plug Connectors, Series III
Shielded Plugs
B
AMPLIMITE .050 Series
Connectors, Series III
.050
[1.27]
Typ.
.100
[2.54]
Typ.
.224
[5.69]
Shielded Plug
±.003
D [±0.08]
±.003
Mating Face
A [±0.08]
Typ.
Shell
.588±.010
[14.94±0.25]
Typ.
.327
[
+.003
-.002
+0.08
8.31 -0.05
]
Housing
Wire Lacing Termination Covers
Termination
Area
Typ.
Materials:
Housing and Covers—
Thermoplastic, 94V-0 rated, black or
gray
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, tin on termination end, all
underplated .nickel
Shell—Steel, plated tin-nickel alloy
over nickel over min. copper
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter.
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Instruction Sheet—408-9427
Shielded Plug with Unassembled Wire Lacing Termination Covers
Connector With Unassembled Wire Lacing Termination Covers
No. of
Pos.
26
50
68
100
A
Dimensions
B
D
.293
7.44
.293
7.44
.293
7.44
.373
9.47
.600
15.24
1.200
30.48
1.650
41.91
2.450
62.23
.979
24.87
1.579
40.11
2.029
51.54
2.829
71.86
Part Numbers
.032-.036
.029-.031
[0.81-0.91]
[0.74-0.79]
Outer Wire Dia. Black Outer Wire Dia. Gray
5750913-2
1-5750913-2
5750913-5
1-5750913-5
5750913-7
1-5750913-7
—
1-5750913-9
Notes: 1. Plug connector requires backshell kit for complete assembly. Refer to pages 16-19 for backshell kit part
numbers.
2. For termination, cover closing and wire lacing tooling, see page 14.
Note: All part numbers are RoHS compliant.
12
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Cable Plug Connectors, Series III (Continued)
Shielded Plugs
(Continued)
.100
[2.54]
Plug Shell
.224
[5.69]
Shielded Plug with Unassembled
Standard Termination Covers
AMPLIMITE .050 Series
Connectors, Series III
B
.050
[1.27]
Terminating Cover
.588
[14.94]
E
Plug Housing
D
.327
[8.31]
Terminating Cover
Shielded Plug with Assembled
Standard Termination Covers
Materials:
Shielded Plug with Assembled or Unassembled Standard Termination Covers
Housing and Covers—
Thermoplastic, 94V-0 rated, black
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, tin on termination end, all
underplated nickel
Shell—Steel, plated tin-nickel alloy
over nickel over copper
Recommended wire size3 —
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter.
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Instruction Sheet—408-9427
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Connectors With Standard Termination Covers
No. of
Pos.
20
26
28
40
50
68
80
100
120
B
.450
11.43
.600
15.24
.650
16.50
.950
24.13
1.200
30.48
1.650
41.91
1.950
49.53
2.450
62.23
2.950
74.93
Dimensions
D
.829
21.06
.979
24.87
1.029
26.14
1.329
33.76
1.579
40.11
2.029
51.54
2.329
59.16
2.829
71.86
3.329
84.56
E
.293
7.44
.293
7.44
.293
7.44
.293
7.44
.293
7.44
.293
7.44
.373
9.47
.373
9.47
.373
9.47
Part Numbers
w/Rails & Latchblocks
w/Latchblocks
5749111-1
5749621-1
1-5749111-0
5749621-2
—
5749621-3
5749111-3
5749621-4
5749111-4
5749621-5
5749111-6
5749621-7
5749111-7
5749621-8
5749111-8
5749621-9
5749111-9
1-5749621-0
Notes: 1. Plug connector requires backshell kit for complete assembly and must use round jacketed cable (discrete
or laminated). Refer to pages 16-19 for backshell kit part numbers.
2. For termination tooling, see pages 28 & 29.
3. The CHAMPOMATOR 2.5 Automatic Termination Machine will accept diameters as low as .023 [0.58].
Note: All part numbers are RoHS compliant.
13
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Cable Plug Connectors, Series III (Continued)
AMPLIMITE .050 Series
Connectors, Series III
AMPLIMITE .050 Series
Connector Application
Tooling for Use with Wire
Lacing Termination Covers
Manual Arbor Frame
Assembly—Part No. 58024-1
Equipped with Cover
Lacing Assembly—Part No.
91293-1 (Includes Seating
Bars for 50 and 100
Positions). See Table 3 for
Seating Bar Part Numbers.
Extra Lacing Stations available for use with Lacing
Assembly—Part No. 91293-1
Order Lower Tooling
Assembly—Part No. 543481-1
Arbor Frame, Part No. 58024-1
Equipped with
Cover Lacing Assembly,
Part No. 91293-1
Miniature Applicator Frame Assembly
Part No. 91295-1
Lower Tooling Assembly Equipped with Cover Closing Kit
Part No. 543508-1
Part No. 543481-1
Table Number 3
Note: AMP Manual Miniature
Applicator Frame Assembly, Cover
Closing Kit, and Staple Insertion Kit
each must be ordered separately by
part number.
Seatings Bars
No. of
Pos.
Seating Bar
Part No.
26
543494-2
40
543494-3
50
543494-1
68
543502-2
100
543502-1
Note: All Tooling must be ordered
separately by part number.
Note: All part numbers are RoHS compliant.
14
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Cable Receptacle Connectors, Series III
Shielded Receptacles
.050
[1.27]
Terminating
Cover
AMPLIMITE .050 Series
Connectors, Series III
.592
[15.04] Ref.
B
E
Shielded Receptacle
with Assembled
Termination Covers
Receptacle
Housing
Receptacle
Shell
Materials:
Housing and Covers—
Thermoplastic, 94V-0 rated, black
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, tin on termination end, all
underplated nickel
Shell—Steel, plated bright tin over
copper
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter.
Terminating
Cover
D
Mating Face
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
No. of
Pos.
40
50
68
100
B
.950
24.13
1.200
30.48
1.650
41.91
2.450
62.23
Dimensions
D
1.329
33.76
1.579
40.11
2.029
51.54
2.829
71.86
E
.293
7.44
.293
7.44
.293
7.44
.373
9.47
Part Numbers
Connectors With Standard Termination Covers
Assembled Covers
Unassembled Covers
—
—
5749210-5
5749699-5
5749210-7
5749699-7
—
5749699-8
Notes: 1. Receptacle connector requires backshell kit for complete assembly. Refer to pages 16-19 for backshell
kit part numbers.
2. For termination, cover closing and wire lacing tooling, see page 14.
3. For Termination Tooling other than Wire Lacing see pages 28 & 29.
Note: All part numbers are RoHS compliant.
15
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Shielded Backshell Kits, With Jackscrews,
Series III
Cable Supplied
By Customer
Strain Relief Staple
(1 Supplied)
AMPLIMITE .050 Series
Connectors, Series III
Jackscrew 2-56 Thd.
(2 Supplied)
Machine Screw
A
Straight Exit
Male Jackscrews
Style A
Connector (Must Be
Purchased Separately)
B
Upper Shield
(1 Supplied)
C
Lower Shield
(1 Supplied)
Style A
Straight Exit Male Jackscrews
Strain Relief
(1 Supplied)
Cable Supplied
By Customer
Jackscrew 2-56 Thd.
(2 Supplied)
Straight Exit
Male Jackscrews
Style B
A
Machine Screws
(4 Supplied)
Connector
(Must be
Purchased
Separately)
B
.404
[10.26]
Upper Shield
(1 Supplied)
Straight Exit
Female Jackscrews
Style A
C
Lower Shield
(1 Supplied)
Style B
Straight Exit Male Jackscrews
Cable Supplied
By Customer
Materials:
Jackscrews—Stainless steel or steel,
black electroless nickel plated
Jackscrew Caps—Polyolefin or PVC,
black
2-56 Screws—Stainless steel
Backshell—Zinc, plated nickel over
copper
Strain Relief Staple—Steel, plated
tin over nickel
Strain Relief Staple
(1 Supplied)
Jackscrew 2-56 Thd.
(2 Supplied)
Machine Screw
A
B
Upper Shield
(1 Supplied)
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Instruction Sheet—408-9427
Connector (Must Be
Purchased Separately)
C
Lower Shield
(1 Supplied)
Style A
Straight Exit Female Jackscrews
16
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Shielded Backshell Kits, With Jackscrews,
Series III (Continued)
No. of
Pos.
Style
Dimensions
B
A
C
Pkg.
40
B
1.822
46.25
1.830
46.48
.456
11.58
Bulk
Bulk
50
68
100
A
B
A
1.270
32.26
2.085
52.96
.480
12.19
1.887
47.93
1.822
46.28
2.082
52.88
1.695
43.05
2.645
67.18
2.525
64.14
3.325
84.46
3.325
84.46
.660
16.76
.564
14.33
.615
15.62
.595
15.11
Individual
Bulk
Bulk
Individual
Individual
Individual
.450
11.43
.400
10.16
.350
8.89
.400
10.16
.400
10.16
.550
13.97
.550
13.97
.500
12.70
.500
12.70
Male with
#2-56
Threads
Female with
#2-56
Threads
5787543-1
1-5787543-7
5787543-2
1-5787543-8
5787543-3
1-5787543-9
5749080-1
—
5749080-2
—
5750752-3
—
5786152-3
—
5749854-1
—
5749081-1
—
AMPLIMITE .050 Series
Connectors, Series III
Bulk
Max.
O.D.
Notes: 1. Each backshell kit includes upper and lower backshells, two male or female jackscrews, one strain relief staple and two or four #2-56 screws.
All are packaged unassembled.
Notes: 2. For Staple Insertion Tooling see page 29.
Note: All part numbers are RoHS compliant.
17
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Shielded Backshell Kits, With Spring Latches,
Series III
AMPLIMITE .050 Series
Connectors, Series III
Strain Relief Staple
(1 Supplied)
Cable Supplied
by Customer
Rear Plug
Machine Screw
A
Spring Latch
(2 Supplied)
Style A
Straight Exit
with Latches
Upper Backshell,
(1 Supplied)
Connector
(Must be
Purchased
Separately)
B
C
Lower Backshell
(1 Supplied)
Style A
Straight Exit with Latches
Style A
Angled Exit
with Latches
Cable Supplied
by Customer
Strain Relief Staple
(1 Supplied)
Machine Screw
A
Spring Latch
(2 Supplied)
Upper Backshell
(1 Supplied)
Style B
Straight Exit
with Latches
B
Connector
(Must be
Purchased
Separately)
C
Lower Backshell
(1 Supplied)
Materials:
Backshell—Zinc, plated nickel over
copper
Spring Latch—Stainless steel
2-56 Screws—Stainless steel
Strain Relief Staple—Steel, plated
tin over nickel
Style A
Angled Exit with Latches
Cable Supplied
by Customer
Strain Relief Staple
(1 Supplied)
Spring Latch
(2 Supplied)
A
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Instruction Sheet—408-9427
Note: Extra pin contact protection is provided
by rails on the receptacle, which facilitate a
straight-out unmating motion. A side-to-side
rocking motion should not be used to disengage the connector system.
Machine Screw
B
Connector
(Must be
Purchased
Separately)
Upper Backshell
(1 Supplied)
C
Lower Backshell
(1 Supplied)
Style B
Straight Exit with Latches
18
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Shielded Backshell Kits, With Spring Latches,
Series III (Continued)
Straight Exit
with
Latches
Angled Exit
with
Latches
Individual
.270
6.86
5749190-1
5749199-1
.400
10.16
Individual
.270
6.86
—
5749609-1
.400
10.16
Individual
.270
6.86
749608-2
—
.320
8.13
—
5749201-1
.320
8.13
5749192-1
—
Individual
.400
10.16
—
5749202-2
Bulk
.400
10.16
5749202-3
—
.355
9.02
5749193-1
—
.400
10.16
5749193-2
—
Bulk
.480
12.19
5749889-3
—
Individual
.480
12.18
5749889-4
—
.400
10.16
—
5749204-1
.440
11.18
5749195-2
5749204-2
.420
10.67
—
5749205-1
.500
12.70
749196-2
—
5749197-1
5749206-1
5749198-1
5749207-1
C
A
1.290
32.77
1.215
30.86
.400
10.16
A
1.290
32.77
1.365
34.67
B
1.290
32.77
1.335
33.91
20
26
A
A
1.715
43.56
1.290
32.77
1.965
49.91
1.395
35.43
.400
10.16
.480
12.19
50
Individual
B
68
Individual
A
1.965
49.91
1.800
45.72
1.405
35.69
2.415
61.34
.492
12.50
.520
13.21
Individual
A
1.600
40.64
2.715
68.96
.565
14.35
100
A
1.725
43.82
3.215
81.66
.615
15.62
Individual
.500
12.70
120
A
1.725
43.82
3.715
94.36
.665
16.89
Individual
.550
13.97
80
Individual
AMPLIMITE .050 Series
Connectors, Series III
Max.
O.D.
Dimensions
B
Style
40
Pkg.
A
No. of
Pos.
Note: All part numbers are RoHS compliant.
19
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Shielded Enclosure Kits,
With Male Jackscrews, Series III
AMPLIMITE .050 Series
Connectors, Series III
68-Position
Material and Finish:
Backshells—Zinc
Boot—PVC, black
Jackscrews—Stainless steel and PVC,
black
Staple—Carbon steel, plated tin over
nickel
Screws—Stainless steel, #2-56 threads
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
.550
[13.97]
Max. Dia.
Cable Supplied
by Customer
1.887
[47.93]
2.645
[67.18]
Connector
(Must be
Purchased
Separately)
.660
[16.76]
.520
[13.21]
No. of
Pos.
Part Number
Male 2-56 Jackscrews
Part Number
Male 4-40 Jackscrews
68
5750752-1
5750752-2
Notes: 1. Each enclosure kit contains two backshells, one boot, two jackscrews,
one staple and two screws. All are packaged unassembled.
2. For staple insertion tooling see page 29.
3. Meets SCSI-3 standards.
Note: All part numbers are RoHS compliant.
20
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Panel Mount Receptacle Assemblies
Without Rails, With Latch Blocks, Series III
AMPLIMITE .050 Series
Connectors, Series III
C
Recessed Cavity
Identification
.050
[1.27]
Typ.
.406
[10.31]
Materials:
2-56 UNC*
2 Plc.
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Shell—Steel, plated bright nickel over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, bright tin in termination
area, all nickel underplated
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter or
.050 [1.27] centerline, 28 AWG
[0.08-0.09mm2] stranded, PVC, flat
ribbon cable.
E
F
±.004
[±0.10]
.201±.002
[5.11±0.05]
Mating Face
.596
[15.14] Ref.
Typ.
.170±.002
[4.32±0.05]
D
Contact
Typ.
Housing
±.007
[±0.18]
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Dimensions
D
E
Part Numbers
Connectors With Unassembled
Wire Lacing Termination Covers
Connectors With Assembled
.032-.036
.029-.031
Standard Termination Covers
[0.81-0.91]
[0.74-0.79]
Outer Wire Dia. Outer Wire Dia.
No. of
Pos.
C
50
1.830
46.48
1.629
41.38
2.065
52.45
1.665
42.29
1-749656-1
5-786862-5
6-786862-5
50
1.830
46.48
1.629
41.38
2.065
52.45
1.665
42.29
5-750640-1*
5-786865-5*
—
68
2.280
57.91
2.079
52.81
2.515
63.88
2.115
53.72
1-749656-2
—
—
120
3.580
90.93
3.379
85.83
3.815
96.90
3.415
86.74
6-749656-0
—
—
F
*Part Numbers 5-750640-1 and 5-786865-5 have 4-40 threaded holes. All others have 2-56 threaded holes.
Note: For termination, cover closing and wire lacing tooling, see page 14.
Note: For termination tooling other than wire lacing see pages 28 & 29.
Note: All part numbers are RoHS compliant.
21
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Panel Mount Flat Top Receptacle Assemblies
Without Rails and Latch Blocks, Series III
C
AMPLIMITE .050 Series
Connectors, Series III
.050
[1.27]
Typ.
Cavity
Identification
Terminating
Cover
.406
[10.31]
Receptacle
Housing
4-40 UNC
2 Plcs.
Materials:
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Shell—Steel, plated bright nickel over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end; tin on solder end; all nickel
underplated
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter or
.050 [1.27] centerline, 28 AWG
[0.08-0.09mm2] stranded, PVC,
flat ribbon cable
E
.197
[5.00]
Mating Face
.592
Ref.
[15.04]
.170 ± .002
[4.32 ± 0.05]
Typ.
D
± .007
[± 0.18]
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
C
Dimensions
D
E
Part Numbers
Connectors With Assembled
Standard Termination Covers
50
1.830
46.48
1.629
41.38
2.065
52.45
5-749877-5
68
2.280
57.91
2.079
52.81
2.515
63.88
5-749877-7
100
3.080
78.23
2.879
73.13
3.315
84.20
5-749877-9
Pos.
No. of
Note: For termination, cover closing and wire lacing tooling, see page 14.
Note: For termination tooling other than wire lacing see pages 28 & 29.
Note: All part numbers are RoHS compliant.
22
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Panel Mount Plug Assemblies
With Rails, Latch Blocks, Series III
Plug
C
AMPLIMITE .050 Series
Connectors, Series III
.050
Typ.
[1.27]
Recessed Cavity
Identification
.406
[10.31]
2-56 UNC
2 Plc.
Materials:
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, bright tin in termination
area, all nickel underplated
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter or
.050 [1.27] centerline, 28 AWG
[0.08-0.09mm2] stranded, PVC, flat
ribbon cable.
E
F
.217 ± .002
[5.51 ± 0.05]
± .004
[± 0.10]
.024 ± .001 Typ.
[0.61 ± 0.03]
Mating Face
.598 Ref.
[15.19]
.154 ± .002
[3.91 ± 0.05]
D
± .007
[± 0.18]
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Note: Extra pin contact protection is provided
by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion
should not be used to disengage the connector
system.
No. of
Positions
50
68
100
C
1.830
46.48
2.280
57.91
3.080
78.23
Dimensions
D
E
1.629
2.065
41.38
52.45
2.079
2.515
52.81
63.88
2.879
3.315
73.13
84.20
F
1.665
42.29
2.115
53.72
2.915
74.04
Part
Numbers
5-749878-5
5-749878-7
5-749878-9
Note: All part numbers are RoHS compliant.
23
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Panel Mount Plug Assemblies
With Rails, Latch Blocks, Series III (Continued)
C
AMPLIMITE .050 Series
Connectors, Series III
.050
[1.27]
Typ.
Cavity Identification
.406
[10.31]
2-56 UNC*
2 Plc.
Materials:
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Shell—Steel, plated bright nickel over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, bright tin in termination
area, all nickel underplated
Recommended wire size—
28 AWG [0.08-0.09mm2] or
30 AWG [0.05mm2], solid or
7 strand, with a .029-.036
[0.74-0.89] insulation diameter or
.050 [1.27] centerline, 28 AWG
[0.08-0.09mm2] stranded, PVC, flat
ribbon cable.
E
±.004
F [±0.05]
.201±.002
[5.11±0.05]
Typ.
Mating Face
.596
[15.14]
Typ.
.170±.002
[4.32±0.05]
Typ.
Contact
Typ.
Housing
±.007
D [±0.18]
Technical Documents:
Product Specifications—108-1228
Application Specifications—
114-40029
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
Note: Extra pin contact protection is provided
by rails, which facilitate a straight-out, unmating motion. A side-to-side rocking motion
should not be used to disengage the connector
system.
No. of
Pos.
C
D
E
F
Part Numbers
Connectors With Assembled
Standard Termination Covers
20
1.080
27.43
.879
22.33
1.315
33.40
.915
23.24
5-749611-2*
26
1.230
31.24
1.029
26.14
1.465
37.21
1.065
27.05
5-749611-1*
50
1.830
46.48
1.629
41.38
2.065
52.45
1.665
42.29
5-749611-5*
50
1.830
46.48
1.629
41.38
2.065
52.45
1.665
42.29
5-750450-1*
100
3.080
78.23
2.879
73.13
3.315
84.20
2.915
74.04
5-749611-9*
Dimensions
*Part Number 750450-1 has 4-40 threaded holes. All others have 2-56 threaded holes.
Note: For termination, cover closing and wire lacing tooling, see page 14.
Note: For termination tooling other than wire lacing see pages 28 & 29.
Note: All part numbers are RoHS compliant.
24
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Plug Assemblies Unshielded
for .025 [0.64] Centerline Ribbon Cable, Series III
.050 Typ.
[1.27]
Plug Assembly
AMPLIMITE .050 Series
Connectors, Series III
E
±.003
[±0.08]
Materials:
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, bright tin on termination
end, all over nickel underplating
Recommended wire size—
.025 [0.64] centerline, 30 AWG
[0.05mm2] solid or 7 strand, PVC,
flat ribbon cable.
Note: Cable must be approved by
TE Engineering.
.778±.015
[19.76±0.38]
Unshielded
Plug Housing
.423
[10.74]
Termination
Cover
.025
[0.64]
F
±.003
[±0.08]
No. of
Pos.
Technical Documents for
5786090-7 only:
50
Product Specifications—108-1359
Application Specifications—
114-40049
68
Dimensions
E
F
1.578
1.578
40.07
40.07
5390377-51
2.029
51.54
5786090-7
Part
No.
2.023
51.30
Note: Termination Tooling: Manual Arbor Press Part No. 91085-2 or
Pneumatic Press Part No. 91112-3, Universal Base Tool Part
No. 768338-4, and Connector Specific Kit Part No. 679235-2.
Refer to page 29.
1 Accepts 32 AWG Flat Ribbon Cable. Selection of compatible ribbon cable is
the responsibility of the user.
Note: Refer to TE Customer drawings and Application Spec for PCB & panel layouts.
A
Backshell Kit for 5786090-7
.025 [0.64] CLC Unshielded
Plug
±.015
B [±0.38]
.682±.020
[17.32±0.51]
Typ.
.400±.015
[10.16±0.38]
.833
[21.16]
Typ.
Materials:
Backshell—Thermoplastic, 94V-0
rated, black
Spring Latches—Stainless steel
No. of
Pos.
Kit
Part No.
68
787032-7
.596±.019
[15.14±0.48] .466
2 Plc.
[11.84]
4 Plc.
Strain Relief for 5786090-7
.025 [0.64] CC
L Unshielded
Plug
1.715±.003
[43.56±0.08]
68-Position
Part No. 787043-7
Materials:
Thermoplastic, 94V-0 rated, black
Note: Pull tab Part No. 88450-8
can be used with this strain relief.
Must be ordered separately.
Dimensions
A
B
2.415 [61.34]
2.125 [53.48]
.356±.002
[9.04±0.05]
2.109±.009
[53.57±0.23]
Note: All part numbers are RoHS compliant.
25
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Hardware and Dust Covers, Series III
Screwlock Kits
.187
[4.75]
Materials:
AMPLIMITE .050 Series
Connectors, Series III
Stainless steel (female)
Steel, zinc plated black (male)
Screwlock
(2 Supplied)
#2-56 Thd.
Related Product Data:
Used with the following
connectors:
Right-Angle Receptacle Header—
page 7
Vertical Receptacle Header—
pages 8-11
Panel Mount Plug and Receptacle
Headers—pages 21 & 22
.062 Panel
[1.57]
.177
[4.50]
Male
Part No. 749086-1
(Includes two screwlocks)
Connector
.532
[13.51]
.050
[1.27]
Technical Documents:
#4-40 Thd.
Product Specifications—108-1228
Application Specifications—
114-40029
.187
[4.75]
#2-56 Thd.
Screwlock
.062 Panel
[1.57]
Female
(Includes two screwlocks)
Dim.
A
.562
14.27
.380
9.65
.562
14.27
1
Dim.
B
.157
3.99
.157
3.99
.165
4.19
Individual Kits
Part No.
Bulk
Part No.
749087-1
—
749087-21
749087-3
749087-4*
749087-8
B
Connector
A
.050
[1.27]
#4-40 Thd.
Recommended for right-angle board mount connectors.
.187 Dia.
[4.75]
2-56 UNC
B
Min. Deep
.027±.003
[0.69±0.08] Typ.
Female
(Includes two screwlocks)
Thread Size
A
B
Kits
Part No.
Bulk
Part No.
4-40
.110
2.79
750644-1*
—
2-56
.090
2.29
786585-2
786585-3
.100±.003
[2.54±0.08]
.355
[9.02]
Recommended for pc board mount of panel mount connectors with
latches or latches and rails. Permits cable connectors to be spring latchtype or jackscrew-type
Note: All part numbers are RoHS compliant.
A
26
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Performance Specifications and
Technical Documents
Performance Specifications for
Right-Angle, Vertical and .050
Centerline Cable Products
Mating Cycles (Durability): 500 max.
Current Rating (30°C T-Rise): 1A max., 50% energized
AMPLIMITE .050 Series
Connectors, Series III
Termination Resistance (Mated): 25 milliohms max.
Insulation Resistance: 1000 megohms min.
Dielectric Withstanding Voltage: 500 VAC
Header Processing Temperature: +220°C max. for 3 minutes
Temperature Range: –55°C to 105°C
Performance Specifications for
.025 [1.27] Centerline Ribbon
Cable Product. Same as above
except:
Current Rating (30°C T-Rise): 1A max. center four contacts energized (two from top row, two
from bottom row)
Termination Resistance (Mated): 50 milliohms max.
Product Specifications:
108-1228
AMPLIMITE .050 Series Printed Circuit Board Mounted and Cable Applied
108-1359
AMPLIMITE .050 Series .025 [0.64] Centerline Connectors
108-1228
AMPLIMITE .050 Series Stacked Connectors
108-1228-2 AMPLIMITE .050 Series ACTION PIN Connectors
108-1228-3 AMPLIMITE .050 Series SBus Connectors
Application Specifications:
114-40029 AMPLIMITE .050 Series Printed Circuit Board Mounted and Cable Applied
Connectors
114-40049 AMPLIMITE .050 Series .025 [0.64] Centerline Connectors
Instruction Sheets:
408-6923
AMP Manual Arbor Frame Assembly
408-6927
TE Design Recommendations for Printed Circuit Board
Support Fixture
408-9200
AMP Single Wire Insertion Tool
408-9822
Wire Termination Tooling Kit for CHAMPOMATOR 2.5 Machine
408-9820
AMP Cover Closing and Staple Inserter Kits
408-9663
AMP Mass Insertion Tool
408-9750
AMP Cover Lacing Fixture
408-9757
AMP Tooling Assembly for ACTION PIN Receptacles
408-9817
AMP Manual Miniature Applicator Frame Assembly
408-9427
Round-to-Flat Cable Termination
408-9875
AMP Universal Base Tool for .025 [0.64] CL Connectors
408-9892
AMP Tool Kit for .025 [0.64] CL Connectors
Customer Manuals:
409-5839
CHAMPOMATOR 2.5 Machine
409-5791
Control Unit for CHAMPOMATOR 2.5 Machine
27
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Application Tooling, Series III
Discrete Wire
Application Tooling
AMPLIMITE .050 Series
Connectors, Series III
To meet medium to high
volume production of
dis-crete wire terminations,
TE offers the following
tooling:
The CHAMPOMATOR
Model 2.5 Bench
Terminating Machine—
Part No. 354786-1, used in
conjunction with Control
Module—Part No. 852423-▫,
and Tie Bar—Part No.
762637-▫ (Table No. 1).
Control Module
Part No. 852423-1 120 VAC
852423-2 100 VAC
852423-3 230 VAC
CHAMPOMATOR
2.5 Machine Tool Kit
Part No. 354786-1
Note: The CHAMPOMATOR 2.5 Machine includes plug
and receptacle nests, as well as wire setup gauge.
Table Number 1
Connector
Size
Tie Bar
Part No.
20 Pos.
1-762637-1
26 Pos.
1-762637-1
28 Pos.
1-762637-2
40 Pos.
1-762637-3
50 Pos.
1-762637-4
60 Pos.
1-762637-5
68 Pos.
1-762637-6
80 Pos.
1-762637-7
100 Pos.
1-762637-9
120 Pos.
1-762637-0
Discrete Wire
Application Tooling
For low to medium volume
production use the AMP
Arbor Frame Assembly—
Part No. 58024-1 equipped
with Applicator—Part No.
91291-1 for .032-.035
[0.81-0.89] Conductor
Insulation O.D. and Applicator—Part No. 91291-2
for .029-.032 [0.74-0.81]
Conductor Insulation O.D.
Note: AMP Arbor Frame Assembly and
Applicator Kit must be ordered separately.
Note: All part numbers are RoHS compliant.
Arbor Frame
Part No. 58024-1
Equipped with
Applicator Part No.
91291-
▫
28
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Application Tooling, Series III (Continued)
Cover Closing/
Termination Tooling
AMPLIMITE .050 Series
Connectors, Series III
Manual Miniature Applicator
Frame Assembly—
Part No. 91295-1
This Frame requires Cover
Closing Kit—Part No. 543508-1
Cable Staple Tooling
To provide cable strain relief
use Manual Miniature
Applicator Frame Assembly—
Part No. 91295-1. This Frame
requires Staple Insertion
Kit—Part No. 543515-1 to
install staples into lower
backshells of connector kits
and assemblies.
AMPLIMITE .050 Series
Connector Application
Tooling for Use with Wire
Lacing Terminating Covers
Staple Insertion Kit
Part No. 543515-1
(For use with Miniature Applicator
Frame Assembly
Part No. 91295-1)
Miniature Applicator Frame Assembly
Part No. 91295-1
Equipped with Cover Closing Kit
Part No. 543508-1
Manual Arbor Frame
Assembly—Part No. 58024-1
Equipped with Cover
Lacing Assembly—Part No.
91293-1 (Includes Seating
Bars for 50 and 100 Positions).
See Table 3 for Seating Bar
Part Numbers.
Extra Lacing Stations available for use with Lacing
Assembly—Part No. 91293-1
Order Lower Tooling
Assembly—Part No. 543481-1
Seatings Bars
Table Number 3
Seating Bar
Part No.
26
543494-2
50
543494-1
68
543502-2
100
543502-1
Notes: All Tooling must be ordered
separately by part number.
Two seating bars required
per tool assembly.
Arbor Frame, Part No. 58024-1
Equipped with
Cover Lacing Assembly, Part No. 91293-1
Note: AMP Manual Miniature
Applicator Frame Assembly, Cover
Closing Kit, and Staple Insertion
Kit each must be ordered separately
by part number.
Lower Tooling Assembly
Part No. 543481-1
No. of
Pos.
Termination Tooling for
.025 [0.64] Centerline
Ribbon Cable
Used with Manual Arbor
Tool Part No. 91085-2, or
Pneumatic Arbor Tool Part No.
91112-3 and Universal Base
Tool Part No. 768338-4.
No. of
Pos.
50
68
Plug/Receptacle
Upper Tooling Kit
679235-2
Note: All part numbers are RoHS compliant.
29
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors
Product Facts
AMPLIMITE .050 Series
Connectors, Series III
Compact design, profile
for the right-angle header
1.230 x .588 [31.24 x 14.94],
vertical header 1.230 x .433
[31.24 x 11.00], right-angle
stacked headers 1.230 x
.803 [31.24 x 20.40]
Housings and covers made
of UL 94V-0 rated thermoplastic
Headers are compatible
with surface mount reflow
solder processes
Header footprint for rightangle and stacked configurations is .100 x .050
[2.54 x 1.27] staggered
centerlines
Right-angle and stacked
headers feature integral
boardlocks for positive board
retention and grounding
Stacked headers reduce
overall total header volume
by 48% and PC board area
by 38%
Stacked headers offer
optional contact shield for
additional EMI/RFI protection
Plugs preloaded with
insulation displacement
contacts (IDC) provide fast,
reliable and economical
terminations
Aesthetically designed backshell kits feature easy-to-use
finger grip jackscrews to
secure mated connectors
Listed and complies with UL
1863, Communication
Circuit Accessories,
File No. E81956
R
Certified by
Canadian Standards
Association
File No. 1088108
(LR 7189A-207)
■
■
R
Produced under a Quality
Management System certified to ISO 9001
A copy of the
ISO900e1d
certificate is available
tifi
upon request
r
Ce
Shielded AMPLIMITE .050
Series, Slimline Connectors
answer today’s industry
requirement for higher
density in a smaller overall
package. The present line
consists of 26 position,
shielded right-angle, 26
position right-angle stacked
PCB receptacle header, and
mating 26 position plug
connectors. All header, plug
and backshell housings are
made of UL 94V-0 rated
thermoplastic. PCB headers
are compatible with surface
mount reflow solder
processes. Right-angle and
stacked PCB headers feature con-tact footprints on
.100 x .050 [2.54 x 1.27]
staggered centerlines.
The compact design of the
right-angle header package
measures only 1.230 W x
.588 D x .300 H [31.24 W x
14.94 D x 7.62 H] for maximum board real estate conservation. Right-angle PCB
headers feature integral
boardlocks for positive board
retention and grounding.
Right-angle stacked headers
provide 52 contacts in a
package only .635 [16.13]
high, allowing parallel
(board-over-board) board
spacing of .800 [20.32].
Centerlines between the top
connector and the bottom
connector measure .335
[8.51] when compared to
.400 [10.16] on the standard
.050 Series stacked headers.
This results in an over-all
reduction of total header
volume, in comparison to
the standard AMPLIMITE
.050 Series header, of 48%,
and a comparative reduction
in PC board area of 38%.
Stacked header board
retention and stabilization
is provided by two boardlocks and four grounding
posts. In addition, an
optional rear contact shield
is available for additional
EMI/RFI protection.
The mating plug connector
consists of a thermoplastic
housing, preloaded with
insulation displacement
contacts (IDC) for fast, reliable terminations that offer
greater applied cost savings. TE offers a choice of
termination equipment to
meet your production
requirements.
The backshell hardware kit
includes a two-piece, aesthetically designed, thermoplastic cover over an inner
and outer shield and two,
high strength #2-56 male
jackscrews with insulated
heads (easy finger grip
caps) to secure mated
connectors.
The AMPLIMITE .050
Series, Slimline family of
connectors offers keyed
coupling. This feature eliminates the problem of mismatch mating of plug and
receptacle, particularly in
stacked applications.
30
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors (Continued)
Right-Angle Header,
Receptacle
.118
[3.00]
AMPLIMITE .050 Series
Connectors, Series III
Date Code Marked
In Area Indicated
.975
[24.77]
.588
[14.94]
Position 1
Part No. 750823-1
.300
[7.26]
Material and Finish
.100
[2.54]
1.230
[31.24]
Housing—UL 94V-0 rated thermoplastic, black
Bracket—Zinc, plated tin or tin over
copper
Metal-Shell—Carbon steel, plated tin
over copper
Boardlocks—Copper alloy, tin plated
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, tin plated on solder end, all
over nickel
Position 26
.263
[6.680]
.050
[1.27]
Typ.
.338
[8.59]
.188
[4.76]
.050
[1.27]
Typ.
.600
[15.24]
Notes:
1. Rear panel mounting only.
2. Female screwlocks to be used with connectors mounted to panels having a thickness of .047 [1.19].
3. See Application Specification 114-40036 for the most up-to-date detailed panel cutout and recommended
PC Board hole pattern.
4. Female screwlocks are not included with receptacles and must be ordered separately. See page 33 for screwlock kit
information.
Note: All part numbers are RoHS compliant.
31
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors (Continued)
Shielded Right-Angle
Stacked Header,
Receptacle
Shield
Date Code Marked
In Area Indicated
AMPLIMITE .050 Series
Connectors, Series III
.168
[4.27]
.215
[5.46]
2 Plc.
.870±.015
[22.10±0.38]
.803
[20.40]
Position 1
With Shielding
Position 1
Position 26
.635
[16.13]
1.230
[31.24]
Position 26
Without Shielding
Material and Finish:
.363
[9.22]
.050
[1.27]
Typ.
Housing—UL 94V-0 rated thermoplastic, black
Bracket—Zinc, plated tin over copper
Metal-Shell—Carbon steel, plated tin
over copper
Boardlocks—Copper alloy, tin plated
Contact Shield—Phosphor bronze,
plated tin
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. on
mating end, tin plated on solder end, all
over nickel
.188
[4.76]
.538
[13.67]
.050 Typ.
[1.27]
.600
[15.24]
Shielded Header with Rear Contact Shield
No. of
Positions
26/26
Part Numbers
Std. Rcpt. without
Rcpt. with
Rear Contact Shield
Rear Contact Shield3
Keyed1
Unkeyed2
Keyed1
Unkeyed2
—
5786200-1
5750821-1 5750820-1
Lower header unkeyed with 4-40 threaded holes, upper header keyed in keying
position 1. See page 33 for keying code.
Both headers unkeyed with 4-40 threaded holes.
3Receptacle includes a metal contact shield for added RFI protection to the rear
of the receptacle assembly.
1
2
Note: See Application Specification 114-40036 for the most up-to-date detailed panel cutout and recommended PC Board hole pattern.
Note: All part numbers are RoHS compliant.
32
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors (Continued)
Cable Connector, Plug
AMPLIMITE .050 Series
Connectors, Series III
Part No. 750833-1
Material and Finish:
.275
[6.99]
Housing and Termination Covers—
UL 94V-0 rated thermoplastic, black
Shell—Steel, plated bright tin over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end, bright tin on termination
end, all underplated nickel
Bracket—Zinc, plated nickel over
copper
Recommended Wire Size—28 AWG
[0.08 mm2] with max. O.D. .032 [0.813].
PVC or polyolefin insulation.
.576
[14.63]
.975
[24.77]
1.170
[29.72]
Note: Cable Connectors must be used with Backshell Kits. See page 34.
Keying Code, Receptacle
Keying Code, Plug
Position 1 (Up)
Accessories
#2-56 Thread
.170
[4.32]
Female Screwlock Kit
.142
[3.61]
Material—Stainless Steel
.170
[4.32]
Note: Female screwlocks to be used with connectors mounted to panels having a thickness
of .047 [1.19]
.390
[9.91]
#4-40 Thread
Part No.
750831-1
Packaging
Individually Packed Kit
(2 Screwlocks per kit)
*Minimum order is 510 kits.
Note: All part numbers are RoHS compliant.
33
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors (Continued)
AMPLIMITE .050 Series
Connectors, Series III
Backshell Kits
1.745
[44.32]
Material and Finish:
Backshells—Copper-nickel alloy
Jackscrews—Steel, plated tin over
copper, handles covered with ABS, gray
Keyed and Unkeyed Inserts—Zinc,
plated tin over copper
Outside Covers—ABS, gray
1.250
[31.75]
.330
[8.38]
Connector shown for illustration purposes
only, must be purchased separately.
.805
[20.45]
Cable Supplied
By Customer
Must Be
TE Approved
Inner Shell
1.531
[38.89]
Outer Shell
1.252
[31.80]
.275
[6.98]
Plug Assembly Must Be
Purchased Separately
Backshell Kits
Unkeyed Kit
Part No.
750850-1
750850-2
Cable Dia.
Packaging*
.250-.280
6.35-7.11
Individually Packed Kit
Bulk Packed Kit
750850-3
.280-.310
7.11-7.87
Individually Packed Kit
*Bulk packaging—100 kits per box.
Note: All part numbers are RoHS compliant.
34
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Slimline Connectors, Application Tooling
Discrete Wire
Application Tooling
The CHAMPOMATOR
Model 2.5 Bench
Terminating Machine—
Part No. 354786-1, used in
conjunction with Control
■,
Module—Part No. 852423-■
and Tie Bar—Part No.
1-762637-3.
Note: CHAMPOMATOR 2.5
Machine and Control Module
must be ordered separately by
part number.
Control Module
Part No. 852423-1 120 VAC
852423-2 100 VAC
852423-3 230 VAC
AMPLIMITE .050 Series
Connectors, Series III
To meet medium to high
volume production of discrete wire terminations, TE
offers the following tooling:
CHAMPOMATOR
2.5 Machine
Part No. 354786-1
26 Position
Tie Bar
1-762637-3
Wire Setup Gauge
Wire Insulation Dia.
mm
in.
0.66-0.71
.026-.028
.029-.031
0.74-0.79
.032-.035
0.81-0.89
Part No.
763382-3
763382-4
763382-5
Discrete Wire
Application Tooling
For low to medium volume
production use the TE Arbor
Tool—Part No. 58024-1
equipped with Applicator—
Part No. 91291-1 and Special
Locator—Part No. 543506-1.
Cable-to-Shell Staple
Tooling (For discrete
wire jacketed cable only)
Arbor Tool
Part No. 58024-1
Equipped with
Applicator Part No.
91291-1
To meet medium to high
volume production use
TE Pneumatic Crimper—
Part No. 312522-3 equipped
with Die Holder Assembly—
Part No. 58449-1 and Die—
Part No. 90437-1 to crimp
outer backshells onto inner
backshells of connector kits
and assemblies.
For low volume use Manual
Arbor Tool—Part No. 91085-2,
equipped with Backshell
Crimper Assembly Tool—
Part No. 856684-1.
For tooling information call
Tooling Assistance Center
1-800-722-1111.
Staple Insertion Kit
Part No. 543515-1
(For use with Miniature Applicator
Frame Assembly
Part No. 91295-1)
Backshell Tooling and
Cover Tooling
Miniature Applicator Frame Assembly
Part No. 91295-1
Equipped with Cover Closing Kit
Part No. 543508-1
Pneumatic Bench Tool
No. 312522-3
(Requires Die Set Holder
No. 58449-1)
To assemble backshell into
plastic housing use Manual
Miniature Applicator Frame
Assembly—Part No. 91295-1
equipped with Part No.
543521-1. To assemble
upper cover on lower
cover use Part No. 91295-1
equipped with Part No.
543522-1.
Note: All part numbers are RoHS compliant.
35
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
Shielded AMPLIMITE .050 Series Contact Arrangements, Performance
Specifications, Technical Documents—Slimline Connectors
A
AMPLIMITE .050 Series
Connectors, Series III
Contact Arrangements
Position 1
C
B
Note: Mating face of receptacle is shown, plug is mirror image.
No. of
Pos.
26
A
13
Position No.
B
C
14
26
Performance Specifications
Mating Cycles (Durability): 500 max.
Current Rating (30°C T-Rise): 1A max., 50% loading
Termination Resistance (Mated): 25 milliohms max.
Insulation Resistance: 1000 megohms min.
Dielectric Withstanding Voltage: 500 VAC
Header Processing Temperature: +220°C max. for 3 minutes
Temperature Range: –55°C to +105°C
Technical Documents
Product Specifications describe technical performance
characteristics and verification tests. They are intended for
the Design, Component and Quality Engineer.
108-1366
Shielded AMPLIMITE .050 Series,
Slimline Connectors
Application Specifications describe requirements for using
the product in its intended application and/or termination information. They are intended for the Packaging and
Design Engineer and the Setup person.
114-40036
Shielded AMPLIMITE .050 Series,
Slimline Connectors
Instruction Sheets provide instructions for assembling or
applying product. They are intended for Manufacturing
Assembler or Operator.
408-9663
Mass Insertion Tooling–Part No. 91291-■
■
408-6923
AMP Manual Arbor Frame–Part No. 58024-1
408-9701
Wire Termination Tooling Kit for CHAMPOMATOR 2.5
Machine–Part No. 1-762661-4
408-7777
AMP Manual Arbor Frame w/Slide–Part No. 91085-2
408-9746
Crimper Assembly–Part No. 856684-1
408-9200
Single Wire Insertion Tool–Part No. 58430-1
408-9721
Die Holder Assembly for Pneumatic Crimper–
■
Part No. 58449-■
408-9788
Die Assembly–Part No. 90437-1
408-9898
Backshell and Cover Tooling Assemblies–
Part No. 543521-1 and 543522-1
Customer Manuals provide information on TE termination
equipment. They are intended for Manufacturing Assemblers or
Operators.
409-5786
CHAMPOMATOR 2.5 Machine
409-5791
CHAMPOMATOR 2.5 Control Module–
■
Part No. 852423-■
409-5822
Pneumatic Crimper–Part No. 312522-3
409-5843
Pneumatic Power Unit
Note: All part numbers are RoHS compliant.
36
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015
AMPLIMITE Subminiature D Connectors
AMPLIMITE .050 Series Panel Mount Receptacle Assemblies
for .025 [0.64] Centerline Ribbon Cable, Series III
E
±.006
[±0.15]
.050
[1.27] Typ.
AMPLIMITE .050 Series
Connectors, Series III
.406
[10.31]
see table
Materials:
Housing and Termination Covers—
Thermoplastic, 94V-0 rated, black
Shell—Steel, plated bright tin over
copper
Bracket—Zinc, plated nickel over
copper
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold on
mating end; tin on solder end; all nickel
underplated
Recommended wire size—
.025 [0.64] centerline, 30 AWG
[0.05mm2] and 32 AWG [0.03mm2]
solid or 7 strand, PVC, flat ribbon cable.
Selection of compatible ribbon cable is
the responsibility of the user.
latch
blocks
.170±.002
[4.32±0.05]
Termination Cover
Receptacle Housing
.025
[0.64]
F
See customer drawings for
Product Performance criteria.
50
Recognized under
the Component Program
of Underwriters
Laboratories, Inc.,
File No. E28476
R
Certified by
Canadian Standards
Association,
File No. LR 7189
±.004
[±0.10]
.423
[10.74]
Technical Documents:
■
G
.201±.002
[5.11±0.05]
No. of
Pos.
■
.786±.015
[19.96±0.38]
Panel Mount
Bracket
H
R
68
E
1.831
46.50
1.831
46.50
1.831
46.50
1.831
46.50
1.831
46.50
1.831
46.50
2.281
57.93
2.281
57.93
2.281
57.93
2.281
57.93
2.281
57.93
±.003
[±0.08]
Dimensions
F
G
1.602
N/A
40.70
1.602
N/A
40.70
1.602
40.70
1.602
40.70
1.602
40.70
1.602
40.70
2.018
51.50
2.018
51.50
2.018
51.50
2.018
51.50
2.018
51.50
1.664
42.27
1.664
42.27
1.664
42.27
1.664
42.27
N/A
N/A
2.114
53.70
2.114
53.70
2.114
53.70
H
2.066
52.47
2.066
52.47
2.066
52.47
2.066
52.47
2.066
52.47
2.066
52.47
2.516
63.90
2.516
63.90
2.516
63.90
2.516
63.90
2.516
63.90
Gold
Plating
Mating Hardware
Part No.
15µ
w/ 4-40 threaded holes
1-5390378-5
30µ
w/ 4-40 threaded holes
5390378-5
30µ
w/ latch blocks and
4-40 threaded holes
w/ latch blocks and
4-40 threaded holes
w/ latch blocks and
4-40 threaded holes
w/ latch blocks and
2-56 threaded holes
15µ
w/ 4-40 threaded holes
1-5390378-7
30µ
w/ 4-40 threaded holes
5390378-7
flash
15µ
30µ
flash
15µ
30µ
w/ latch blocks and
4-40 threaded holes
w/ latch blocks and
4-40 threaded holes
w/ latch blocks and
4-40 threaded holes
2-5390399-5
1-5390399-5
5390399-5
5390379-5
2-5390399-7
1-5390399-7
5390399-7
Note: Termination Tooling: Manual Arbor Press Part No. 91085-2 or Pneumatic Press Part No. 91112-3, Universal
Base Tool Part No. 768338-4, and Connector Specific Kit Part No. 1490479-1.
Note: All part numbers are RoHS compliant.
37
Catalog 82068
Revised 4-12
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in inches and
millimeters unless otherwise
specified.
USA: +1 (800) 522-6752
Canada: +1 (905) 475-6222
Mexico/C. Am.: +52 (0) 55-1106-0800
Latin/S. Am.: +54 (0) 11-4733-2200
Germany: +49 (0) 6251-133-1999
UK: +44 (0) 800-267666
France: +33 (0) 1-3420-8686
Netherlands: +31 (0) 73-6246-999
China: +86 (0) 400-820-6015