SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 D D D D D D D D D D D D D State-of-the-Art Advanced BiCMOS Technology (ABT) Widebus Design for 2.5-V and 3.3-V Operation and Low Static Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 2.3-V to 3.6-V VCC ) Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25°C High-Drive (–24/24 mA at 2.5-V and –32/64 mA at 3.3-V VCC) Power Off Disables Outputs, Permitting Live Insertion High-Impedance State During Power Up and Power Down Prevents Driver Conflict Uses Bus Hold on Data Inputs in Place of External Pullup/Pulldown Resistors to Prevent the Bus From Floating Auto3-State Eliminates Bus Current Loading When Output Exceeds VCC + 0.5 V Latch-Up Performance Exceeds 250 mA Per JESD 17 ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model; and Exceeds 1000 V Using Charged-Device Model, Robotic Method Flow-Through Architecture Facilitates Printed Circuit Board Layout Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Package Options Include Plastic Shrink Small-Outline (DL), Thin Shrink Small-Outline (DGG), Thin Very Small-Outline (DGV) Packages, and 380-mil Fine-Pitch Ceramic Flat (WD) Package SN54ALVTH16821 . . . WD PACKAGE SN74ALVTH16821 . . . DGG, DGV, OR DL PACKAGE (TOP VIEW) 1OE 1Q1 1Q2 GND 1Q3 1Q4 VCC 1Q5 1Q6 1Q7 GND 1Q8 1Q9 1Q10 2Q1 2Q2 2Q3 GND 2Q4 2Q5 2Q6 VCC 2Q7 2Q8 GND 2Q9 2Q10 2OE 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 1CLK 1D1 1D2 GND 1D3 1D4 VCC 1D5 1D6 1D7 GND 1D8 1D9 1D10 2D1 2D2 2D3 GND 2D4 2D5 2D6 VCC 2D7 2D8 GND 2D9 2D10 2CLK description The ’ALVTH16821 devices are 20-bit bus-interface flip-flops with 3-state outputs designed for 2.5-V or 3.3-V VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. The devices can be used as two 10-bit flip-flops or one 20-bit flip-flop. The 20-bit flip-flops are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK), the flip-flops store the logic levels set up at the D inputs. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments Incorporated. Copyright 1999, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 description (continued) A buffered output-enable (OE) input can be used to place the ten outputs in either a normal logic state (high or low level) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operation of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. When VCC is between 0 and 1.2 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.2 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. The SN54ALVTH16821 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ALVTH16821 is characterized for operation from –40°C to 85°C. FUNCTION TABLE (each 10-bit section) INPUTS 2 OE CLK D OUTPUT Q L ↑ H H L ↑ L L L H or L X Q0 H X X Z POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 logic diagram (positive logic) 1OE 1CLK 1 56 One of Ten Channels 1D1 C1 55 2 1D 1Q1 To Nine Other Channels 2OE 2CLK 28 29 One of Ten Channels 2D1 C1 42 1D 15 2Q1 To Nine Other Channels POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Output current in the low state, IO: SN54ALVTH16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ALVTH16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Output current in the high state, IO: SN54ALVTH16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –48 mA SN74ALVTH16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions, VCC = 2.5 V ± 0.2 V (see Note 3) SN54ALVTH16821 SN74ALVTH16821 MIN MAX MIN 2.7 2.3 VCC VIH Supply voltage 2.3 High-level input voltage 1.7 VIL VI Low-level input voltage IOH High-level output current IOL ∆t/∆v TYP TYP 2.7 1.7 0 VCC 5.5 –6 Low-level output current 0.7 0 VCC V V 5.5 V –8 mA 6 8 Low-level output current; current duty cycle ≤ 50%; f ≥ 1 kHz 18 24 Input transition rise or fall rate 10 10 Outputs enabled UNIT V 0.7 Input voltage MAX mA ns/V ∆t/∆VCC Power-up ramp rate 200 200 µs/V TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 recommended operating conditions, VCC = 3.3 V ± 0.3 V (see Note 3) SN54ALVTH16821 SN74ALVTH16821 MIN MAX MIN 3.6 3 VCC VIH Supply voltage 3 High-level input voltage 2 VIL VI Low-level input voltage IOH High-level output current IOL ∆t/∆v TYP TYP 3.6 2 0 5.5 0.8 0 V VCC V 5.5 V –24 –32 mA Low-level output current 24 32 Low-level output current; current duty cycle ≤ 50%; f ≥ 1 kHz 48 64 Input transition rise or fall rate 10 10 Outputs enabled VCC UNIT V 0.8 Input voltage MAX mA ns/V ∆t/∆VCC Power-up ramp rate 200 200 µs/V TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 electrical characteristics over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER VIK VOH VCC = 2.3 V, VCC = 2.3 V to 2.7 V, II = –18 mA IOH = –100 µA 3V VCC = 2 2.3 IOH = –6 mA IOH = –8 mA VCC = 2.3 V to 2.7 V, VOL VCC = 2 2.3 3V Control inputs VCC = 2.7 V, VCC = 0 or 2.7 V, II Data inputs Ioff IBHL‡ IBHH§ SN54ALVTH16821 MIN TYP† MAX TEST CONDITIONS VCC = 2.7 V SN74ALVTH16821 MIN TYP† MAX –1.2 VCC–0.2 1.8 –1.2 V 1.8 IOL = 100 µA IOL = 6 mA 0.2 0.2 0.4 IOL = 8 mA IOL = 18 mA 0.4 IOL = 24 mA VI = VCC or GND 0.5 VI = 5.5 V VI = 5.5 V VI = VCC VI = 0 ±1 ±1 10 10 10 10 1 1 –5 –5 ±100 VCC = 2.3 V, VCC = 2.7 V, VI = 1.7 V VI = 0 to VCC IEX|| VCC = 2.7 V, VCC = 2.3 V, VI = 0 to VCC VO = 5.5 V IOZ(PU/PD)k VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care IOZH VCC = 2 2.7 7V IOZL 7V VCC = 2 2.7 Outputs high ICC VCC = 2.7 V, IO = 0, VI = VCC or GND Outputs disabled VCC = 2.5 V, VCC = 2.5 V, VI = 2.5 V or 0 VO = 2.5 V or 0 3.5 3.5 6.5 6.5 Co V 0.5 VI or VO = 0 to 4.5 V VI = 0.7 V Ci V VCC–0.2 VCC = 0, VCC = 2.3 V, IBHLO¶ IBHHO# UNIT µA µA 115 115 µA –10 –10 µA 300 300 µA –300 –300 µA 125 125 µA ±100 ±100 µA VO = 2.3 V, VI = 0.7 V or 1.7 V 5 5 µA VO = 0.5 V, VI = 0.7 V or 1.7 V 5 –5 5 –5 µA Outputs low 0.04 0.1 0.04 0.1 2.3 0.04 4.5 2.3 4.5 0.1 0.04 0.1 mA pF pF † All typical values are at VCC = 2.5 V, TA = 25°C. ‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. § The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. ¶ An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) PARAMETER VIK VOH VCC = 3 V, VCC = 3 V to 3.6 V, II = –18 mA IOH = –100 µA VCC = 3 V IOH = –24 mA IOH = –32 mA VCC = 3 V to 3.6 V, VOL VCC = 3 V Control inputs Ioff IBHL‡ IBHH§ IBHLO¶ IBHHO# IEX|| 2 IOL = 100 µA IOL = 16 mA 0.2 IOL = 24 mA IOL = 32 mA 0.5 IOL = 48 mA IOL = 64 mA 0.55 0.2 0.4 0.5 V 0.55 ±1 ±1 10 10 10 10 1 1 VCC = 3.6 V VI = 0 VI or VO = 0 to 4.5 V –5 VCC = 3.6 V, VCC = 3 V, V V VI = 5.5 V VI = VCC VCC = 3 V, VCC = 3.6 V, –1.2 UNIT VCC–0.2 VI = VCC or GND VI = 5.5 V VCC = 0, VCC = 3 V, SN74ALVTH16821 MIN TYP† MAX –1.2 VCC–0.2 2 VCC = 3.6 V, VCC = 0 or 3.6 V, II Data inputs SN54ALVTH16821 MIN TYP† MAX TEST CONDITIONS VI = 0.8 V VI = 2 V VI = 0 to VCC VI = 0 to VCC µA –5 ±100 µA 75 75 µA –75 –75 µA 500 500 µA –500 µA –500 125 125 µA ±100 ±100 µA IOZ(PU/PD)k VO = 5.5 V VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care IOZH VCC = 3 3.6 6V VO = 3 V, VI = 0.8 V or 2 V 5 5 µA IOZL VCC = 3 3.6 6V VO = 0.5 V, VI = 0.8 V or 2 V –5 5 –5 5 µA ICC VCC = 3.6 V, IO = 0, VI = VCC or GND Outputs high 0.07 0.1 0.07 Outputs low 3.2 5.5 3.2 5 0.07 0.1 0.07 0.1 Outputs disabled ∆ICCh VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VCC = 3.3 V, VCC = 3.3 V, Co VI = 3.3 V or 0 VO = 3.3 V or 0 0.4 0.1 0.4 3.5 3.5 6 6 mA mA pF pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. § The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. ¶ An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down h This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 timing requirements over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) SN54ALVTH16821 MIN fclock tw Clock frequency MAX SN74ALVTH16821 MIN 150 Pulse duration, CLK high or low tsu time data before CLK↑ Setup time, th Hold time time, data after CLK↑ MAX 150 1.6 1.5 Data high 1.6 1.5 Data low 2.1 2 Data high 0.4 0.3 Data low 1.1 1 UNIT MHz ns ns ns timing requirements over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 2) SN54ALVTH16821 MIN fclock tw Clock frequency MAX SN74ALVTH16821 MIN 150 Pulse duration, CLK high or low tsu Setup time, time data before CLK↑ th Hold time time, data after CLK↑ MAX 150 1.6 1.5 Data high 1.6 1.5 Data low 1.6 1.5 Data high 1.1 1 Data low 1.1 1 UNIT MHz ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 30 pF, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER fmax tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) SN54ALVTH16821 MIN MAX 150 CLK Q OE Q OE Q SN74ALVTH16821 MIN MAX 150 UNIT MHz 1 4.2 1 4.1 1 4.5 1 4.4 1.5 4.7 1.5 4.6 1 4.2 1 4.1 1.5 4.6 1.5 4.5 1 5 1 4.9 ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 2) PARAMETER fmax tPLH tPHL tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) SN54ALVTH16821 MAX 150 CLK Q OE Q OE Q PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 8 MIN POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74ALVTH16821 MIN MAX 150 UNIT MHz 1 3.6 1 3.5 1 3.6 1 3.5 1 4.2 1 4.1 1 3.7 1 3.6 1 4.9 1 4.8 1 4.8 1 4.6 ns ns ns SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION VCC = 2.5 V ± 0.2 V 2 × VCC S1 500 Ω From Output Under Test Open GND CL = 30 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ tPZH VOH VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 SN54ALVTH16821, SN74ALVTH16821 2.5-V/3.3-V 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES078E – JULY 1996 – REVISED JANUARY 1999 PARAMETER MEASUREMENT INFORMATION VCC = 3.3 V ± 0.3 V 6V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND LOAD CIRCUIT tw 3V 3V Timing Input 1.5 V VOLTAGE WAVEFORMS PULSE DURATION th 3V 1.5 V 3V 1.5 V 0V 0V Output Output Waveform 1 S1 at 6 V (see Note B) 3V 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ tPZH tPHL VOH 1.5 V tPLZ tPZL 1.5 V tPLH 1.5 V 0V 3V 1.5 V 1.5 V Output Control VOLTAGE WAVEFORMS SETUP AND HOLD TIMES Input 1.5 V 0V 0V tsu Data Input 1.5 V Input 1.5 V VOH VOH – 0.3 V ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform22 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 2. Load Circuit and Voltage Waveforms 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated