TI SE555D

NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
FEATURES
•
•
Timing From Microseconds to Hours
Astable or Monostable Operation
•
•
Adjustable Duty Cycle
TTL-Compatible Output Can Sink or Source
up to 200 mA
DESCRIPTION/ORDERING INFORMATION
These devices are precision timing circuits capable of producing accurate time delays or oscillation. In the
time-delay or monostable mode of operation, the timed interval is controlled by a single external resistor and
capacitor network. In the astable mode of operation, the frequency and duty cycle can be controlled
independently with two external resistors and a single external capacitor.
The threshold and trigger levels normally are two-thirds and one-third, respectively, of VCC. These levels can be
altered by use of the control-voltage terminal. When the trigger input falls below the trigger level, the flip-flop is
set, and the output goes high. If the trigger input is above the trigger level and the threshold input is above the
threshold level, the flip-flop is reset and the output is low. The reset (RESET) input can override all other inputs
and can be used to initiate a new timing cycle. When RESET goes low, the flip-flop is reset, and the output goes
low. When the output is low, a low-impedance path is provided between discharge (DISCH) and ground.
The output circuit is capable of sinking or sourcing current up to 200 mA. Operation is specified for supplies of
5 V to 15 V. With a 5-V supply, output levels are compatible with TTL inputs.
NA555...D OR P PACKAGE
NE555...D, P, PS, OR PW PACKAGE
SA555...D OR P PACKAGE
SE555...D, JG, OR P PACKAGE
(TOP VIEW)
1
8
2
7
3
6
4
5
VCC
DISCH
THRES
CONT
NC
GND
NC
VCC
NC
NC
TRIG
NC
OUT
NC
4
3 2 1 20 19
18
5
17
6
16
7
15
14
9 10 11 12 13
8
NC
DISCH
NC
THRES
NC
NC
RESET
NC
CONT
NC
GND
TRIG
OUT
RESET
SE555...FK PACKAGE
(TOP VIEW)
NC – No internal connection
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1973–2006, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are
tested unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
ORDERING INFORMATION
TA
VTHRES
MAX
VCC = 15 V
PACKAGE (1)
PDIP – P
11.2 V
NE555P
Tube of 75
NE555D
Reel of 2500
NE555DR
Reel of 2000
NE555PSR
Tube of 150
NE555PW
Reel of 2000
NE555PWR
Tube of 50
SA555P
Tube of 75
SA555D
Reel of 2000
SA555DR
Tube of 50
NA555P
Tube of 75
NA555D
Reel of 2000
NA555DR
Tube of 50
SE555P
Tube of 75
SE555D
Reel of 2500
SE555DR
CDIP – JG
Tube of 50
SE555JG
SE555JG
LCCC – FK
Tube of 55
SE555FK
SE555FK
SOP – PS
TSSOP – PW
PDIP – P
–40°C to 85°C
11.2 V
SOIC – D
PDIP – P
–40°C to 105°C
11.2 V
SOIC – D
PDIP – P
–55°C to 125°C
(1)
10.6
TOP-SIDE MARKING
Tube of 50
SOIC – D
0°C to 70°C
ORDERABLE PART NUMBER
SOIC – D
NE555P
NE555
N555
N555
SA555P
SA555
NA555P
NA555
SE555P
SE555D
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
FUNCTION TABLE
(1)
2
RESET
TRIGGER
VOLTAGE (1)
THRESHOLD
VOLTAGE (1)
OUTPUT
DISCHARGE
SWITCH
Low
Irrelevant
Irrelevant
Low
On
High
<1/3 VDD
Irrelevant
High
Off
High
>1/3 VDD
>2/3 VDD
Low
On
High
>1/3 VDD
<2/3 VDD
Voltage levels shown are nominal.
Submit Documentation Feedback
As previously established
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
FUNCTIONAL BLOCK DIAGRAM
VCC
8
6
THRES
2
TRIG
CONT
5
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Î
Î
Î
RESET
4
R1
R
S
1
Î
Î
Î
Î
Î Î
3
OUT
7
DISCH
1
GND
Pin numbers shown are for the D, JG, P, PS, and PW packages.
NOTE A: RESET can override TRIG, which can override THRES.
Submit Documentation Feedback
3
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
MIN
VCC
Supply voltage (2)
VI
Input voltage
IO
Output current
θJA
Package thermal impedance (3) (4)
θJC
Package thermal impedance (5) (6)
TJ
Operating virtual junction temperature
Tstg
(1)
(2)
(3)
(4)
(5)
(6)
CONT, RESET, THRES, TRIG
MAX
UNIT
18
V
VCC
V
±225
mA
D package
97
P package
85
PS package
95
PW package
149
FK package
5.61
JG package
14.5
°C/W
°C/W
150
°C
Case temperature for 60 s
FK package
260
°C
Lead temperature 1, 6 mm (1/16 in) from case for 60 s
JG package
300
°C
150
°C
Storage temperature range
–65
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to GND.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) - TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Maximum power dissipation is a function of TJ(max), θJC, and TC. The maximum allowable power dissipation at any allowable case
temperature is PD = (TJ(max) - TC)/θJC. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with MIL-STD-883.
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VCC
Supply voltage
VI
Input voltage
IO
Output current
TA
4
Operating free-air temperature
MIN
MAX
NA555, NE555, SA555
4.5
16
SE555
4.5
18
CONT, RESET, THRES, and TRIG
V
VCC
V
±200
mA
NA555
–40
105
NE555
0
70
SA555
–40
85
SE555
–55
125
Submit Documentation Feedback
UNIT
°C
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
Electrical Characteristics
VCC = 5 V to 15 V, TA = 25°C (unless otherwise noted)
PARAMETER
THRES voltage level
TEST CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
9.4
10
10.6
8.8
10
11.2
VCC = 5 V
2.7
3.3
4
2.4
3.3
4.2
30
250
5
5.2
1.67
1.9
4.8
VCC = 15 V
TA = –55°C to 125°C
TRIG voltage level
RESET current
3
1.45
VCC = 5 V
RESET voltage level
5.6
1.1
1.67
2.2
0.9
0.7
1
0.5
2
0.7
1
0.3
1.1
RESET at VCC
0.1
0.4
0.1
0.4
RESET at 0 V
–0.4
–1
–0.4
–1.5
20
100
20
100
10
10.4
9
10
11
2.6
3.3
4
0.1
0.25
0.4
0.75
2
2.5
9.6
VCC = 15 V
TA = –55°C to 125°C
9.6
2.9
TA = –55°C to 125°C
VCC = 15 V, IOL = 50 mA
VCC = 15 V, IOL = 100 mA
VCC = 5 V, IOL = 3.5 mA
0.1
0.15
V
TA = –55°C to 125°C
TA = –55°C to 125°C
0.5
2.2
2.7
mA
nA
V
V
2.5
2.5
0.35
0.2
0.1
0.35
0.15
0.4
0.8
0.15
13
0.25
13.3
12.75
13.3
12
VCC = 15 V, IOH = –200 mA
12.5
3
TA = –55°C to 125°C
V
1
2
TA = –55°C to 125°C
µA
0.2
0.4
0.1
VCC = 15 V, IOL = –100 mA
nA
3.8
TA = –55°C to 125°C
VCC = 15 V, IOL = –100 mA
Output high, No load
3.8
TA = –55°C to 125°C
VCC = 5 V, IOL = 8 mA
Supply current
3.3
TA = –55°C to 125°C
VCC = 5 V, IOL = 5 mA
Output low, No load
10.4
2.9
VCC = 15 V, IOL = 200 mA
(1)
0.5
TA = –55°C to 125°C
VCC = 15 V, IOL = 10 mA
High-level output voltage
250
5
V
1.9
0.3
VCC = 5 V
Low-level output voltage
30
4.5
6
TA = –55°C to 125°C
TRIG at 0 V
DISCH switch off-state
current
CONT voltage
(open circuit)
UNIT
VCC = 15 V
THRES current (1)
TRIG current
NA555
NE555
SA555
SE555
12.5
3.3
2.75
V
3.3
2
VCC = 15 V
10
12
10
15
VCC = 5 V
3
5
3
6
VCC = 15 V
9
10
9
13
VCC = 5 V
2
4
2
5
mA
This parameter influences the maximum value of the timing resistors RA and RB in the circuit of Figure 12. For example,
when VCC = 5 V, the maximum value is R = RA + RB ≈ 3.4 MΩ, and for VCC = 15 V, the maximum value is 10 MΩ.
Submit Documentation Feedback
5
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
Operating Characteristics
VCC = 5 V to 15 V, TA = 25°C (unless otherwise noted)
PARAMETER
MIN
Initial error of timing
interval (2)
Each timer, monostable (3)
Temperature coefficient of
timing interval
Each timer, monostable (3)
TYP
MAX
0.5
1.5 (4)
1.5
TA = MIN to MAX
astable (5)
30
TA = 25°C
0.05
MIN
UNIT
TYP
MAX
1
3
2.25
100 (4)
90
(3)
Supply-voltage sensitivity of Each timer, monostable
timing interval
Each timer, astable (5)
50
ppm/
°C
150
0.2 (4)
0.15
0.1
%
0.5
0.3
%/V
Output-pulse rise time
CL = 15 pF,
TA = 25°C
100
200 (4)
100
300
ns
Output-pulse fall time
CL = 15 pF,
TA = 25°C
100
200 (4)
100
300
ns
(1)
(2)
(3)
(4)
(5)
6
TA = 25°C
Each timer, astable (5)
Each timer,
NA555
NE555
SA555
SE555
TEST
CONDITIONS (1)
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
Timing interval error is defined as the difference between the measured value and the average value of a random sample from each
process run.
Values specified are for a device in a monostable circuit similar to Figure 9, with the following component values: RA = 2 kΩ to 100 kΩ,
C = 0.1 µF.
On products compliant to MIL-PRF-38535, this parameter is not production tested.
Values specified are for a device in an astable circuit similar to Figure 12, with the following component values: RA = 1 kΩ to 100 kΩ,
C = 0.1 µF.
Submit Documentation Feedback
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
TYPICAL CHARACTERISTICS
Data for temperatures below 0°C and above 70°C are applicable for SE555 circuits only.
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
4
2
1
0.7
0.4
10
7
VCC = 5 V
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
TA = −55°C
TA = 25°C
TA = 125°C
0.2
0.1
0.07
0.04
VOL − Low-Level Output Voltage − V
VOL − Low-Level Output Voltage − V
10
7
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
0.02
VCC = 10 V
4
2
TA = 25°C
1
0.7
TA= −55°C
TA = 125°C
0.4
0.2
0.1
0.07
0.04
0.02
0.01
0.01
1
2
4
7
10
20
40
70 100
1
IOL − Low-Level Output Current − mA
2
4
Figure 1.
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
2.0
VCC = 15 V
TA = −55°C
1
0.7
TA = 25°C
0.2
TA = 125°C
0.1
0.07
0.04
1.6
1.4
1.2
1
0.8
0.6
0.4
0.02
0.2
0.01
1
2
4
40
70 100
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
TA = −55°C
1.8
2
0.4
20
DROP BETWEEN SUPPLY VOLTAGE AND OUTPUT
vs
HIGH-LEVEL OUTPUT CURRENT
( VCC − VOH) − Voltage Drop − V
VOL − Low-Level Output Voltage − V
4
10
Figure 2.
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
10
7
7
IOL − Low-Level Output Current − mA
7
10
20
40
IOL − Low-Level Output Current − mA
70 100
0
TA = 25°C
TA = 125°C
VCC = 5 V to 15 V
1
Figure 3.
2
4
7 10
20
40
70 100
IOH − High-Level Output Current − mA
Figure 4.
Submit Documentation Feedback
7
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
TYPICAL CHARACTERISTICS (continued)
Data for temperatures below 0°C and above 70°C are applicable for SE555 circuits only.
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
NORMALIZED OUTPUT PULSE DURATION
(MONOSTABLE OPERATION)
vs
SUPPLY VOLTAGE
10
Pulse Duration Relative to Value at VCC = 10 V
Output Low,
No Load
9
I CC − Supply Current − mA
8
TA = 25°C
7
6
5
TA = −55°C
4
TA = 125°C
3
2
1
0
5
6
7
8
9
10
11
12
13
14
15
1.015
1.010
1.005
1
0.995
0.990
0.985
0
VCC − Supply Voltage − V
5
10
15
20
VCC − Supply Voltage − V
Figure 5.
Figure 6.
NORMALIZED OUTPUT PULSE DURATION
(MONOSTABLE OPERATION)
vs
FREE-AIR TEMPERATURE
PROPAGATION DELAY TIME
vs
LOWEST VOLTAGE LEVEL
OF TRIGGER PULSE
300
VCC = 10 V
tPD − Propagation Delay Time − ns
Pulse Duration Relative to Value at TA = 255C
1.015
1.010
1.005
1
0.995
0.990
250
TA = −55°C
200
TA = 0°C
150
100
TA = 25°C
TA = 70°C
50
TA = 125°C
0.985
−75
0
−50
−25
0
25
50
100 125
75
0
TA − Free-Air Temperature − °C
Figure 7.
8
0.1 x VCC
0.2 x VCC
Figure 8.
Submit Documentation Feedback
0.3 x VCC
Lowest Voltage Level of Trigger Pulse
0.4 x VCC
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION
Monostable Operation
For monostable operation, any of these timers can be connected as shown in Figure 9. If the output is low,
application of a negative-going pulse to the trigger (TRIG) sets the flip-flop (Q goes low), drives the output high,
and turns off Q1. Capacitor C then is charged through RA until the voltage across the capacitor reaches the
threshold voltage of the threshold (THRES) input. If TRIG has returned to a high level, the output of the
threshold comparator resets the flip-flop (Q goes high), drives the output low, and discharges C through Q1.
VCC
(5 V to 15 V)
RA
Î
Î
Î
4
7
6
Input
2
5
8
CONT
VCC
RL
RESET
DISCH
OUT
3
Output
THRES
TRIG
GND
1
Pin numbers shown are for the D, JG, P, PS, and PW packages.
Figure 9. Circuit for Monostable Operation
Monostable operation is initiated when TRIG voltage falls below the trigger threshold. Once initiated, the
sequence ends only if TRIG is high at the end of the timing interval. Because of the threshold level and
saturation voltage of Q1, the output pulse duration is approximately tw = 1.1RAC. Figure 11 is a plot of the time
constant for various values of RA and C. The threshold levels and charge rates both are directly proportional to
the supply voltage, VCC. The timing interval is, therefore, independent of the supply voltage, so long as the
supply voltage is constant during the time interval.
Applying a negative-going trigger pulse simultaneously to RESET and TRIG during the timing interval discharges
C and reinitiates the cycle, commencing on the positive edge of the reset pulse. The output is held low as long
as the reset pulse is low. To prevent false triggering, when RESET is not used, it should be connected to VCC.
Submit Documentation Feedback
9
NA555, NE555, SA555, SE555
PRECISION TIMERS
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
10
RA = 9.1 kΩ
CL = 0.01 µF
RL = 1 kΩ
See Figure 9
RA = 10 MΩ
tw − Output Pulse Duration − s
1
Voltage − 2 V/div
Input Voltage
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
Output Voltage
RA = 1 MΩ
10−1
10−2
10−3
RA = 100 kΩ
RA = 10 kΩ
10−4
RA = 1 kΩ
10−5
0.001
Capacitor Voltage
0.01
0.1
1
10
100
C − Capacitance − µF
Time − 0.1 ms/div
Figure 10. Typical Monostable Waveforms
Figure 11. Output Pulse Duration vs Capacitance
Astable Operation
As shown in Figure 12, adding a second resistor, RB, to the circuit of Figure 9 and connecting the trigger input to
the threshold input causes the timer to self-trigger and run as a multivibrator. The capacitor C charges through
RA and RB and then discharges through RB only. Therefore, the duty cycle is controlled by the values of RA and
RB.
This astable connection results in capacitor C charging and discharging between the threshold-voltage level
(≈0.67 × VCC) and the trigger-voltage level (≈0.33 × VCC). As in the monostable circuit, charge and discharge
times (and, therefore, the frequency and duty cycle) are independent of the supply voltage.
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
VCC
(5 V to 15 V)
Î
Î
Î
0.01 µF
Open
(see Note A) 5
8
VCC
CONT
4
7
RB
6
2
RL
RESET
DISCH
3
OUT
Output
THRES
t
H
TRIG
tL
GND
C
Output Voltage
1
Pin numbers shown are for the D, JG, P, PS, and PW packages.
NOTE A: Decoupling CONT voltage to ground with a capacitor can
improve operation. This should be evaluated for individual
applications.
Figure 12. Circuit for Astable Operation
10
RL = 1 kW
See Figure 12
Voltage − 1 V/div
RA
RA = 5 kW
RB = 3 kW
C = 0.15 µF
Submit Documentation Feedback
Capacitor Voltage
Time − 0.5 ms/div
Figure 13. Typical Astable Waveforms
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
Figure 13 shows typical waveforms generated during astable operation. The output high-level duration tH and
low-level duration tL can be calculated as follows:
+ 0.693 (R ) R C
A
B)
t + 0.693 (R C
L
B)
100 k
H
RA + 2 RB = 1 kΩ
RA + 2 RB = 10 kΩ
Other useful relationships are shown below.
period + t ) t + 0.693 (R ) 2R ) C
H
L
A
B
1.44
frequency [
(R ) 2R ) C
A
B
t
Output driver duty cycle +
R
L
B
+
t )t
R
)
2R
H
L
A
B
Output waveform duty cycle
t
R
H + 1–
B
+
t )t
R
)
2R
H
L
A
B
t
R
B
Low-to-high ratio + L +
t
R
)
R
H
A
B
f − Free-Running Frequency − Hz
t
10 k
RA + 2 RB = 100 kΩ
1k
100
10
1
RA + 2 RB = 1 MΩ
RA + 2 RB = 10 MΩ
0.1
0.001
0.01
0.1
1
10
100
C − Capacitance − µF
Figure 14. Free-Running Frequency
Missing-Pulse Detector
The circuit shown in Figure 15 can be used to detect a missing pulse or abnormally long spacing between
consecutive pulses in a train of pulses. The timing interval of the monostable circuit is retriggered continuously
by the input pulse train as long as the pulse spacing is less than the timing interval. A longer pulse spacing,
missing pulse, or terminated pulse train permits the timing interval to be completed, thereby generating an
output pulse as shown in Figure 16.
4
RESET
Input
2
8
VCC
OUT
0.01 µF
3
TRIG
DISCH
5
RL
CONT
THRES
GND
1
7
6
VCC = 5 V
RA = 1 kΩ
C = 0.1 µF
See Figure 15
RA
Output
Voltage − 2 V/div
VCC (5 V to 15 V)
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
Input Voltage
Output Voltage
C
A5T3644
Capacitor Voltage
Time − 0.1 ms/div
Pin numbers shown are shown for the D, JG, P, PS, and PW packages.
Figure 15. Circuit for Missing-Pulse Detector
Figure 16. Completed Timing Waveforms for
Missing-Pulse Detector
Submit Documentation Feedback
11
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
Frequency Divider
By adjusting the length of the timing cycle, the basic circuit of Figure 9 can be made to operate as a frequency
divider. Figure 17 shows a divide-by-three circuit that makes use of the fact that retriggering cannot occur during
the timing cycle.
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
Voltage − 2 V/div
VCC = 5 V
RA = 1250 Ω
C = 0.02 µF
See Figure 9
Input Voltage
Output Voltage
Capacitor Voltage
Time − 0.1 ms/div
Figure 17. Divide-by-Three Circuit Waveforms
12
Submit Documentation Feedback
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
Pulse-Width Modulation
The operation of the timer can be modified by modulating the internal threshold and trigger voltages, which is
accomplished by applying an external voltage (or current) to CONT. Figure 18 shows a circuit for pulse-width
modulation. A continuous input pulse train triggers the monostable circuit, and a control signal modulates the
threshold voltage. Figure 19 shows the resulting output pulse-width modulation. While a sine-wave modulation
signal is shown, any wave shape could be used.
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏÏÏÏ
ÏÏÏÏÏÏ
VCC (5 V to 15 V)
RESET
Clock
Input
2
RL
8
VCC
OUT
TRIG
RA
Modulation Input Voltage
3
Output
Voltage − 2 V/div
4
RA = 3 kΩ
C = 0.02 µF
RL = 1 kΩ
See Figure 18
7
DISCH
Modulation
5
Input
(see Note A)
CONT
THRES
6
GND
1
Clock Input Voltage
C
Output Voltage
Pin numbers shown are for the D, JG, P, PS, and PW packages.
NOTE A: The modulating signal can be direct or capacitively coupled
to CONT. For direct coupling, the effects of modulation source
voltage and impedance on the bias of the timer should be
considered.
Figure 18. Circuit for Pulse-Width Modulation
Capacitor Voltage
Time − 0.5 ms/div
Figure 19. Pulse-Width-Modulation Waveforms
Submit Documentation Feedback
13
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
Pulse-Position Modulation
As shown in Figure 20, any of these timers can be used as a pulse-position modulator. This application
modulates the threshold voltage and, thereby, the time delay, of a free-running oscillator. Figure 21 shows a
triangular-wave modulation signal for such a circuit; however, any wave shape could be used.
RA = 3 kΩ
RB = 500 Ω
RL = 1 kΩ
See Figure 20
VCC (5 V to 15 V)
8
RESET
2
VCC
OUT
RA
3
Output
TRIG
DISCH
Modulation
Input 5
(see Note A)
RL
CONT
THRES
7
6
RB
GND
Modulation Input Voltage
Output Voltage
C
Pin numbers shown are for the D, JG, P, PS, and PW packages.
NOTE A: The modulating signal can be direct or capacitively coupled
to CONT. For direct coupling, the effects of modulation
source voltage and impedance on the bias of the timer
should be considered.
Figure 20. Circuit for Pulse-Position Modulation
14
Voltage − 2 V/div
4
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
Capacitor Voltage
Time − 0.1 ms/div
Figure 21. Pulse-Position-Modulation Waveforms
Submit Documentation Feedback
NA555, NE555, SA555, SE555
PRECISION TIMERS
www.ti.com
SLFS022F – SEPTEMBER 1973 – REVISED JUNE 2006
APPLICATION INFORMATION (continued)
Sequential Timer
Many applications, such as computers, require signals for initializing conditions during start-up. Other
applications, such as test equipment, require activation of test signals in sequence. These timing circuits can be
connected to provide such sequential control. The timers can be used in various combinations of astable or
monostable circuit connections, with or without modulation, for extremely flexible waveform control. Figure 22
shows a sequencer circuit with possible applications in many systems, and Figure 23 shows the output
waveforms.
VCC
4
RESET
2
8
VCC
3
OUT
TRIG
S
DISCH
5
0.01
µF
CONT
4
RESET
RA 33 kΩ
2
TRIG
0.001
µF
7
1
CA = 10 µF
RA = 100 kΩ
CONT
6
0.01
µF
CA
RB
Output A
THRES
GND
1
CB
4
RESET
33 kΩ
2
0.001
µF
DISCH 7
5
THRES
GND
8
VCC
3
OUT
DISCH
5
6
0.01
µF
Output B
CB = 4.7 µF
RB = 100 kΩ
TRIG
8
VCC
3
OUT
CONT
THRES
GND
1
CC
CC = 14.7 µF
RC = 100 kΩ
RC
7
6
Output C
Pin numbers shown are for the D, JG, P, PS, and PW packages.
NOTE A: S closes momentarily at t = 0.
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏ
ÏÏÏ
ÏÏÏÏ
ÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
Figure 22. Sequential Timer Circuit
See Figure 22
Voltage − 5 V/div
Output A
Output B
Output C
twA
ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏÏÏ
ÏÏ
ÏÏÏÏÏ
ÏÏ
ÏÏ ÏÏÏÏÏ
ÏÏÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
ÏÏÏ
twA = 1.1 RACA
twB
twB = 1.1 RBCB
twC
twC = 1.1 RCCC
t=0
t − Time − 1 s/div
Figure 23. Sequential Timer Waveforms
Submit Documentation Feedback
15
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
JM38510/10901BPA
NA555D
Pins Package Eco Plan (2)
Qty
Package
Drawing
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NA555DG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NA555DR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NA555DRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NA555P
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
NA555PE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
NE555D
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555DE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555DG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555DR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555DRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555DRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555P
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
NE555PE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
NE555PSLE
OBSOLETE
SO
PS
8
NE555PSR
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PSRE4
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PSRG4
ACTIVE
SO
PS
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PWE4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PWRE4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555PWRG4
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
NE555Y
OBSOLETE
TBD
0
Addendum-Page 1
TBD
Lead/Ball Finish
MSL Peak Temp (3)
Package
Type
Call TI
Call TI
N / A for Pkg Type
Call TI
Call TI
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SA555D
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555DE4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555DG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555DR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555DRE4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555DRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SA555P
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
SA555PE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
Lead/Ball Finish
MSL Peak Temp (3)
SE555D
ACTIVE
SOIC
D
8
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
SE555DG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SE555DR
ACTIVE
SOIC
D
8
2500
TBD
CU NIPDAU
Level-1-220C-UNLIM
SE555DRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SE555FKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE N / A for Pkg Type
SE555JG
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
SE555JGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
N / A for Pkg Type
SE555N
OBSOLETE
PDIP
N
8
TBD
Call TI
SE555P
ACTIVE
PDIP
P
8
Pb-Free
(RoHS)
CU NIPDAU
50
Call TI
N / A for Pkg Type
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
9-Oct-2007
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
NA555DR
D
8
SITE 27
330
12
6.4
5.2
2.1
8
12
Q1
NA555DR
D
8
SITE 41
330
12
6.4
5.2
2.1
8
12
Q1
NE555DR
D
8
SITE 27
330
12
6.4
5.2
2.1
8
12
Q1
NE555DR
D
8
SITE 41
330
12
6.4
5.2
2.1
8
12
Q1
NE555PSR
PS
8
SITE 41
330
16
8.2
6.6
2.5
12
16
Q1
NE555PWR
PW
8
SITE 41
330
12
7.0
3.6
1.6
8
12
Q1
SA555DR
D
8
SITE 27
330
12
6.4
5.2
2.1
8
12
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
NA555DR
D
8
SITE 27
342.9
336.6
20.64
NA555DR
D
8
SITE 41
346.0
346.0
29.0
NE555DR
D
8
SITE 27
342.9
336.6
20.64
NE555DR
D
8
SITE 41
346.0
346.0
29.0
NE555PSR
PS
8
SITE 41
346.0
346.0
33.0
NE555PWR
PW
8
SITE 41
346.0
346.0
29.0
SA555DR
D
8
SITE 27
342.9
336.6
20.64
Pack Materials-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUARY 1997
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.400 (10,16)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
0.063 (1,60)
0.015 (0,38)
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.023 (0,58)
0.015 (0,38)
0°–15°
0.100 (2,54)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification.
Falls within MIL STD 1835 GDIP1-T8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MLCC006B – OCTOBER 1996
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
A
B
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
9
22
8
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
7
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
5
26
27
28
1
2
3
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a metal lid.
The terminals are gold plated.
Falls within JEDEC MS-004
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated