ADA10000 Linear Amplifier MMIC Data Sheet - Rev 2.3 FEATURES • High Linearity : +15 dBm IIP3 (+8 V supply) • Low Distortion • Low Noise Figure: 2.0 dB • 15 dB Gain • Single +4 V to +9 V Supply • Wide Bandwidth: 50 MHz to 1 GHz • SOIC-16 and SOT-89 Package Options S3 Package Modified 16 Pin SOIC S24 Package SOT-89 PRODUCT DESCIPTION The ADA10000 is a monolithic IC intended for use in applications requiring high linearity, such as Cellular Telephone Base Station Driver Amplifiers, CATV Fiber Receiver and Distribution Amplifiers, and CATV Drop Amplifiers. Offered in both a modified 16 lead SOIC package and SOT-89 package, it is well suited for use in amplifiers where small size, reduced component count, and high reliability are important. RF Output / Bias RF Input Figure 1: Block Diagram 06/2003 ADA10000 1 GND GND 16 2 GND GND 15 3 GND RFOUT 14 4 GND GND 13 5 GND GND 12 6 RFIN GND 11 7 GND GND 10 8 GND GND 9 Figure 2: Pinout - S3 Package Table 1: Pin Description - S3 Package 2 PIN NAME 1 GND 2 DESCRIPTION PIN NAME Ground 16 GND Ground GND Ground 15 GND Ground 3 GND Ground 14 RFOUT RF Output / Bias 4 GND Ground 13 GND Ground 5 GND Ground 12 GND Ground 6 RFIN RF Input 11 GND Ground 7 GND Ground 10 GND Ground 8 GND Ground 9 GND Ground Data Sheet - Rev 2.3 06/2003 DESCRIPTION ADA10000 GND 4 1 2 3 RF IN GND RF OUT Figure 3: Pinout - S24 Package Table 2: Pin Description - S24 Package PIN NAME DESCRIPTION 1 RFIN RF Input 2 GND Ground 3 RFOUT RF Output / Bias 4 GND Ground Data Sheet - Rev 2.3 06/2003 3 ADA10000 ELECTRICAL CHARACTERISTICS Table 3: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply (S3 package: pin 14) (S24 package: pin 3) 0 +12 VD C RF Power at Input (S3 package: pin 6) (S24 package: pin 1) - +10 dB m -65 +150 °C Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: (1) RF input pin must be AC-coupled. No DC external bias should be applied. Table 4: Operating Ranges PARAMETER MIN TYP MAX UNIT RF Input / Output Frequency 50 - 1000 MHz Supply Voltage (VDD) +4 +8 +9 VD C Case Temperature -40 - +85 (1) °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) Median time to failure will degrade above this temperature. 4 Data Sheet - Rev 2.3 06/2003 ADA10000 Table 5: Electrical Specifications (TA = +25 °C, VDD = +8 VDC, 75 Ω system, see Figures 4 and 5) PARAMETER MIN TYP MAX UNIT CSO (1) / CSO (2) 60 / 62 - - dB c CTB 65 / 74 - - dB c 14 15 - dB - 2.0 3.5 dB +29 +34 - dB m +13 +15 - dB m - - 35 20 °C/W 50 - 150 mA (1) /CTB (2) Gain Noise Figure 2nd Order Input Intercept Point (IIP2) (3) 3rd Order Input Intercept Point (IIP3) (3) Thermal Resistance Current Consumption (4) COMMENT S 3 p a cka g e S 2 4 p a cka g e Notes: (1) 160 channels, +17 dBmV per channel (measured at output), 6 MHz channel spacing. (2) 80 channels, +19 dBmV per channel (measured at output), 6 MHz channel spacing. (3) Two tones, -10 dBm per tone at input. (4) The device can be operated at VDD = +6 VDC for lower power dissipation. Refer to Figures 7, 8, 13, and 16 for performance variation with supply voltage. Data Sheet - Rev 2.3 06/2003 5 ADA10000 VDD 0.1 uF 3.9 uH 1000 pF RFOUT 1000 pF ADA10000 5.6 nH RFIN Figure 4: Test Circuit - S3 Packaged Device (75 Ω terminations) VDD 0.01 uF 820 nH 1000 pF RFIN 0.5 pF 10 nH 1 ADA10000 2,4 100 W 3 180 pF RFOUT 0.5 pF 50 W Figure 5: Test Circuit - S24 Packaged Device (75 Ω terminations) 6 Data Sheet - Rev 2.3 06/2003 ADA10000 4.0 3.5 16 3.0 15 2.5 14 2.0 Gain 13 1.5 NF 12 0 200 400 600 1.0 1000 800 16.0 Gain (dB) 17 Figure 7: Gain and Noise Figure vs. Supply Voltage - S3 Packaged Device (TA = +25 oC, f = 500 MHz, 75 W system) 15.8 2.1 15.6 2.0 15.4 1.9 Gain 15.2 15.0 1.7 4 5 6 7 8 9 Supply Voltage (V) Figure 8: IIP2 and IIP3 vs. Supply Voltage - S3 Packaged Device (TA = +25 oC, 75 W system) Figure 9: Output Power vs. Input Power S3 Packaged Device (TA = +25 oC, VDD = +8 V, f = 500 MHz, 75 W system) 26 35 24 Output Power (dBm) 30 IIP2, IIP3 (dBm) 1.8 NF Frequency (MHz) 40 2.2 Noise Figure (dB) Figure 6: Gain and Noise Figure vs. Frequency - S3 Packaged Device o (TA = +25 C, VDD = +8 V, 75 W system) 18 Gain (dB) As measured in test circuits shown in Figures 4 and 5. Noise Figure (dB) PERFORMANCE DATA 25 20 15 20 18 16 IIP2 IIP3 10 22 14 5 4 5 6 7 8 9 0 Figure 10: Unmatched Device Input Impedance S3 Packaged Device o (TA = +25 C, VDD = +8 V, 75 W system) 2 4 6 8 10 12 Input Power (dBm) Supply Voltage (V) Notes: 1. IIP2 measured at 986.5 MHz; Input = two tones at 55.25 MHz and 931.25 MHz at -10 dBm. 2. IIP3 measured with two tones at the input: 986.5 MHz and 992.5 MHz at -10 dBm. Figure 11: Unmatched Device Output Impedance S3 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) 50 MHz 50 MHz 1 GHz 1 GHz Refer to the ANADIGICS web site for full 2-port s-parameter data. Data Sheet - Rev 2.3 06/2003 7 ADA10000 17 3.5 16 3.0 15 2.5 14 2.0 Gain 13 1.5 NF 12 0 200 400 600 1.0 1000 800 Figure 13: Gain and Noise Figure vs. Supply Voltage - S24 Packaged Device (TA = +25 oC, f = 500 MHz, 75 W system) 16.0 15.8 2.1 15.6 2.0 15.4 1.9 Gain 15.2 15.0 1.7 4 5 6 Figure 14: Input Return Loss vs. Frequency - S24 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) 8 9 Figure 15: Output Return Loss vs. Frequency - S24 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) 0 -5 -5 -10 -10 Output Return Loss (dB) Input Return Loss (dB) 7 Supply Voltage (V) -15 -20 -25 -30 -15 -20 -25 -30 -35 -35 -40 -40 0 200 400 600 800 0 1000 200 400 800 1000 Figure 17: Output Power vs. Input Power S24 Packaged Device (TA = +25 oC,VDD = +8 V, f = 500 MHz, 75 W system) Figure 16: IIP2 and IIP3 vs.Supply Voltage - S24 Packaged Device (TA = +25 oC, 75 W system) 40 600 Frequency (MHz) Frequency (MHz) 26 35 24 Output Power (dBm) 30 IIP2, IIP3 (dBm) 1.8 NF Frequency (MHz) 0 2.2 25 20 22 20 18 15 16 IIP2 IIP3 10 14 5 0 4 5 6 7 8 9 Supply Voltage (V) Notes: 1. IIP2 measured at 986.5 MHz; Input = two tones at 55.25 MHz and 931.25 MHz at -10 dBm. 2. IIP3 measured with two tones at the input: 986.5 MHz and 992.5 MHz at -10 dBm. 8 Data Sheet - Rev 2.3 06/2003 2 4 6 Input Power (dBm) 8 10 12 Noise Figure (dB) 4.0 Gain (dB) Gain (dB) 18 Noise Figure (dB) Figure 12: Gain and Noise Figure vs. Frequency - S24 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) ADA10000 Figure 18: Unmatched Device Input Impedance S24 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) Figure 19: Unmatched Device Output Impedance S24 Packaged Device (TA = +25 oC, VDD = +8 V, 75 W system) 50 MHz 50 MHz 1 GHz 1 GHz Refer to the ANADIGICS web site for full 2-port s-parameter data. Data Sheet - Rev 2.3 06/2003 9 ADA10000 PACKAGE OUTLINE D C LE E H L 0.015 [0.38]X45 a A2 A A1 0.003 [0.076mm] B1 e S Y M INCHES B O L MILLIMETERS NOTE MAX. MIN. MAX. A 0.058 0.068 1.47 1.73 A1 0.004 0.010 0.10 0.25 A2 0.055 0.065 1.40 1.65 B 0.013 0.020 0.33 0.50 B1 0.062 0.070 1.58 1.78 C 0.008 0.010 0.20 0.25 4 D 0.380 0.400 9.66 10.16 2 E 0.150 0.160 3.81 4.06 3 0.050 BSC B NOTES: 1. CONTROLLING DIMENSION: INCHES MIN. e 2. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.006 [0.15mm] PER SIDE. 3. DIMENSION "E" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.010 [0.25mm] PER SIDE. 4. LEAD THICKNESS AFTER PLATING TO BE 0.013 [0.33mm] MAXIMUM. 1.27 BSC H 0.226 0.244 5.74 6.20 L 0.016 0.040 0.41 1.02 LE 0.030 a 0 0.76 8 0 8 Figure 20: S3 Package Outline - Modified 16 Pin SOIC 10 GAUGE PLANE SEATING PLANE Data Sheet - Rev 2.3 06/2003 ADA10000 Figure 21: S24 Package Outline - SOT-89 Data Sheet - Rev 2.3 06/2003 11 ADA10000 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION ADA10000S3CTR -40 °C to +85 °C Modified 16 Pin SOIC 3,500 piece Tape and Reel A D A 10000S 3C -40 °C to +85 °C Modified 16 Pin SOIC Plastic tubes (50 pieces per tube) ADA10000S24Q1 -40 °C to +85 °C SOT-89 Package COMPONENT PACKAGING 1,000 piece Tape and Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 Data Sheet - Rev 2.3 06/2003