ADA10000S3C Linear Amplifier MMIC Data Sheet - Rev 1 FEATURES · High Linearity (IIP3 + 15 dBm) · Low Noise Figure (2.0 dB) · Single Supply (+8Vdc) · Wide Bandwidth (50 MHz - 1 GHz) S3C 16 Pin SOIC Package Description The ADA10000 is a monolithic IC intended for use in applications requiring high linearity such as: Cellular Telephone Base Station Driver Amplifiers, CATV Fiber Receiver/Distribution Amplifiers and CATV Drop Amplifiers. Supplied in a surface mount, 16 lead-SOIC package, it is well suited for use in amplifiers where small size, reduced component count, and high reliability are important. PIN External Test Circuit FUNC TION GND GND 3 GND 4 GND 5 GND 6 RFIN 7 GND 8 GND 9 GND 10 GND 11 GND 12 GND 13 GND 14 RFOUT 15 GND 16 GND RF OUT 1000 pF ADA10000 1 2 1000 pF RFIN 5.6 nH 3.9 µH 0.1 µf ADA10000S3C Absolute Maximum Ratings PAR AMETER MIN MAX U N ITS VDD/VRFOUT 0 12 VD C VRFIN - 0 VD C RFIN - +10 dB m -65 +150 0 C Solderi ng Temperature - 260 0 C Solderi ng Ti me - 5.0 Thermal Resi stance - 35 Storage Temperature S e c. 0 C /W Operating Ranges PAR AMETER MIN TYP MAX U N IT V DD 4 8 9 Volts IDD 50 - 150 mA C ase Temperature -40 - 85* 1 0 C * Median time to failure degraded above this temperature Electrical Specifications (TA = +25 °C, RF = 50 to 1000 MHz, Test System = 75W, VDD = + 8VDC) PAR AMETER MIN TYP MAX U N ITS C SO /C SO 60/62 - - dB c C TB2/C TB4 65/74 - - dB c 14 15 - dB - 2.0 3.5 dB 2nd Order Input Intercept Poi nt (IIP2)3 +29 +34 - dB m 3rd Order Input Intercept Poi nt (IIP3)3 +13 +15 - dB m 2 4 Gai n Noi se Fi gure 1. The device can be operated at + 6 VDC for lower power dissipation; Refer to the figures on page for performance variation with supply voltage. 2. 160 channels, + 17 dBmV per channel, (measured at the output) 6 MHz channel spacing. 3. Two tones, - 10 dBm per tone at input. 4. 80 channels, + 19 dBmV per channel @ output, 6 MHz channel spacing. 2 ADA10000S3C Gain and Noise Figure vs Frequency Gain and Noise Figure vs. Vdd 16 3 15 2.5 14 2 13 1.5 12 1 250 450 650 Frequency (MHz) GAIN 2 15.75 1.98 15.7 1.96 15.65 1.94 1.92 15.6 1.9 15.55 1.88 850 4 5 6 7 Vdd (volts) NF GAIN 8 9 NF IIP2,IIP3 vs. Vdd Pin vs. Pout Tc = 25 deg C Tc = 25 deg C, VDD = +8V, RF = 500 MHz 40 37 34 31 28 25 22 19 16 30 27 24 21 18 15 12 9 6 4 2.02 5 6 7 8 26 25 24 9 Vdd (volts) IIP2 Noise Figure (dB) 3.5 Gain (dB) 17 Noise Figure (dB) 4 50 IIP2 (dBm) Tc = 25 deg C, RF = 500 MHz 15.8 18 IP3 (dBm) Gain (dB) Tc = 25 deg C, VDD = +8V 23 22 21 20 19 18 17 16 15 IIP3 0 2 4 6 Pin (dBm) 8 10 12 * Notes: IIP 2 Measured at 986.5 MHz, Input = two tones at 55.25 MHz and 931.25 MHz at - 10 dBm IIP 3 Measured with two tones at the input, RF = 986.5 MHz and 992.5 MHz at - 10 dBm OUTPUT IMPEDANCE INPUT IMPEDANCE START: 0.050 GHz STOP: 1.00 GHz START: 0.050 GHz STOP: 1.00 GHz 1: 1 .5 2 2: .2 -.2 .5 1 3 2 5 4 6 2 5 4: -5 5: -2 -.5 0.40 GHz 70.02 Ω - 21.83 jΩ 0.6 GHz 59.63 Ω - 26.56 jΩ 0.8 GHz 49.91 Ω - 26.56 jΩ -1 6: Measured in 75 Ω System .5 1.0 GHz 41.77 Ω - 25.15 jΩ 0.050 GHz 83.9 Ω - 8.1 jΩ 2: 0.20 GHz 84.17 Ω - 1.19 jΩ 3: 0.40 GHz 85.38 Ω - 2.27 jΩ 4: 0.6 GHz 87.64 Ω - 3.82 jΩ 5: 0.8 GHz 90.20 Ω - 6.60 jΩ 6: 1.0 GHz 93.57 Ω - 11.76 jΩ 2 5 .2 3: 5 1 1 0.20 GHz 77.88 Ω - 13.21 jΩ 5 .2 0 0.050 GHz 79.76 Ω - 4.79 jΩ 1: 5 1 0 .2 .5 1 2 5 6 -.2 -5 -2 -.5 -1 Measured in 75 Ω System 3 ADA10000S3C D C LE E H L 0.015 [0.38]X45 a A2 A A1 GAUGE PLANE 0.003 [0.076mm] B1 e S Y M INCHES B O L MILLIMETERS M IN. M AX. MIN. MAX. A 0.058 0.068 1.47 1.73 A1 0.004 0.010 0.10 0.25 A2 0.055 0.065 1.40 1.65 B 0.013 0.020 0.33 0.50 B1 0.062 0.070 1.58 1.78 NOTE NOTES: 2. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.006 [0.15mm] PER SIDE. 3. DIMENSION "E" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.010 [0.25mm] PER SIDE. C 0.008 0.010 0.20 0.25 4 0.380 0.400 9.66 10.16 2 E 0.150 0.160 3.81 4.06 3 0.050 BSC B 1. CONTROLLING DIMENSION: INCHES D e 4. LEAD THICKNESS AFTER PLATING TO BE 0.013 [0.33mm] MAXIMUM. 1.27 BSC H 0.226 0.244 5.74 6.20 SPECIFICATION: L 0.016 0.040 0.41 1.02 SUBJECT: LE 0.030 a 0 0 98000-006 PUBLISHED OUTLINE, 16 LEAD BATWING SOIC PKG. 0.76 8 SEATING PLANE 8 ANADIGICS, Inc. 35 Technology Drive Warren, New Jersey 07059 Tel: (908) 668-5000 Fax: (908) 668-5132 http://www.anadigics.com [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or discontinue any product at any time without notice. The Advanced Product data sheets and product specifications contained in this data sheet are subject to change prior to a products formal introduction. The information in this data sheet has been carefully checked and is assumed to be reliable. However, ANADIGICS assumes no responsibility for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices, or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 4