SPG1316-H Semiconductor Chip LED Lamp Features • • • • • 1.6mm(L)×0.8mm small size surface mount type Thin package of 0.4mm(H) thickness Transparent clear lens optic Low power consumption type chip LED Emitting light green (525nm) Applications • • • • LCD backlighting Keypad backlighting Symbol backlighting Front panel indicator lamp Outline Dimensions unit : mm KLG-4002-000 1 SPG1316-H Absolute maximum ratings Characteristic Symbol Ratings Unit Power Dissipation PD 80 mW Forward Current IF 20 mA IFP 50 mA Reverse Voltage VR 4 V Operating Temperature Topr -25∼80 ℃ Storage Temperature Tstg -30∼100 ℃ 1 * Peak Forward Current 2 240℃ for 5 seconds * Soldering Temperature Tsol *1.Duty ratio = 1/16, Pulse width = 0.1ms *2. Recommended soldering Temperature Profile Temp(℃) Peak time max 10sec Peak Temp max 240℃ 1~ 4℃/sec 220℃ 140~ 160℃ -2~ -6℃/sec Solder area max. 50sec Preheating area 120 1~4℃/sec Time(sec) Electrical Characteristics Symbol Test Condition Min Typ Max Unit 3 Characteristic VF IF= 10mA 2.6 3.0 3.6 V 4 * Luminous Intensity IV IF= 10mA 62 100 228 mcd Peak Wavelength λP Δλ IR IF= 10mA - 525 - nm IF= 10mA - 35 - nm VR=4V - - 10 uA - ±65 - - ±70 - * Forward Voltage Spectrum Bandwidth Reverse Current *5Half Angle θ1/2 X IF= 10mA Y deg *3. Forward Voltage Maximum tolerance for ±0.1V *4. Luminous Intensity Maximum tolerance for each Grade Classification limit is ±18% (The test result of IF=20mA is only for reference) *5. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity z Iv / VF /λp Grade Classification Forward Voltage(V) 3 : 2.8~3.0 4 : 3.0~3.2 5 : 3.2~3.4 Test Condition @IF=10mA Luminous Intensity(mcd) B : 78~105 C : 105~140 D : 140~190 KLG-4002-000 Peak Wavelength(nm) A : 515~520 B : 520~525 C : 525~530 2 SPG1316-H Characteristic Diagrams Fig. 2 IV - IF Luminous Intensity Iv [mcd] Forward Current IF [mA] Fig. 1 IF - VF Forward Voltage VF [V] Forward Current IF [mA] Fig.4 Spectrum Distribution Forward Relative Intensity [%] Current IF [mA] Fig. 3 IF – Ta Wavelength λ [nm] Ambient Temperature Ta [℃] Fig. 5-1 Radiation Diagram(X) Fig. 5-2 Radiation Diagram(Y) Relative Luminous Intensity Iv [%] KLG-4002-000 Relative Luminous Intensity Iv [%] 3 SPG1316-H These AUK products are intended for usage in general electronic equipments(Office and communication equipment, measuring equipment, domestic electrification, etc.). Please make sure that you consult with us before you use these AUK products in equipments which require high quality and/or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, traffic signal, combustion central, all types of safety device, etc.). AUK cannot accept liability to any damage which may occur in case these AUK products were used in the mentioned equipments without prior consultation with AUK. KLG-4002-000 4