® ADS 774 ADS ADS774 774 ADS 774 Microprocessor-Compatible Sampling CMOS ANALOG-to-DIGITAL CONVERTER FEATURES DESCRIPTION ● REPLACES ADC574, ADC674 AND ADC774 FOR NEW DESIGNS The ADS774 is a 12-bit successive approximation analog-to-digital converter using an innovative capacitor array (CDAC) implemented in low-power CMOS technology. This is a drop-in replacement for ADC574, ADC674, and ADC774 models in most applications, with internal sampling, much lower power consumption, and the ability to operate from a single +5V supply. ● COMPLETE SAMPLING A/D WITH REFERENCE, CLOCK AND MICROPROCESSOR INTERFACE ● FAST ACQUISITION AND CONVERSION: 8.5µs max OVER TEMPERATURE ● ELIMINATES EXTERNAL SAMPLE/HOLD IN MOST APPLICATIONS The ADS774 is complete with internal clock, microprocessor interface, three-state outputs, and internal scaling resistors for input ranges of 0V to +10V, 0V to +20V, ±5V, or ±10V. The maximum throughput time is 8.5µs over the full operating temperature range, including both acquisition and conversion. ● GUARANTEED AC AND DC PERFORMANCE ● SINGLE +5V SUPPLY OPERATION ● LOW POWER: 120mW max ● PACKAGE OPTIONS: 0.6" and 0.3" DIPs, SOIC Complete user control over the internal sampling function facilitates elimination of external sample/hold amplifiers in most existing designs. The ADS774 requires +5V, with –15V optional. No +15V supply is required. Available packages include 0.3" or 0.6" wide 28-pin plastic DIP and 28-pin SOICs. Status Control Inputs 20V Range 10V Range 2.5V Reference Input CDAC Clock – Successive Approximation Register + Comparator 2.5V Reference Output Three-State Buffers Bipolar Offset Control Logic Parallel Data Output 2.5V Reference International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 © 1991 Burr-Brown Corporation PDS-1109F Printed in U.S.A. July, 1995 SPECIFICATIONS ELECTRICAL At TA = TMIN to TMAX , VDD = +5V, VEE = –15V to +5V, sampling frequency of 117kHz, fIN = 10kHz; unless otherwise specified. ADS774JE, JP, JU PARAMETER MIN TYP ADS774KE, KP, KU MAX RESOLUTION MIN TYP 12 MAX UNITS ✻ Bits INPUTS ANALOG Voltage Ranges: Unipolar Bipolar Impedance: 0 to +10V, ±5V ±10V, 0V to +20V DIGITAL (CE, CS, R/C, AO, 12/8) Voltages: Logic 1 Logic 0 Current Capacitance 8.5 35 +2.0 –0.5 –5 0 to +10, 0 to +20 ±5, ±10 ✻ ✻ 12 50 +5.5 +0.8 +5 0.1 5 ✻ ✻ ✻ V V kΩ kΩ ✻ ✻ ✻ ✻ ✻ ✻ ✻ V V µA pF TRANSFER CHARACTERISTICS DC ACCURACY At +25°C Linearity Error Unipolar Offset Error (adjustable to zero) Bipolar Offset Error (adjustable to zero) Full-Scale Calibration Error (1) (adjustable to zero) No Missing Codes Resolution TMIN to TMAX (3) Linearity Error Full-Scale Calibration Error Unipolar Offset Bipolar Offset No Missing Codes Resolution AC ACCURACY (4) Spurious Free Dynamic Range Total Harmonic Distortion Signal-to-Noise Ratio Signal-to-(Noise + Distortion) Ratio Intermodulation Distortion (FIN1 = 20kHz, FIN2 = 23kHz) TEMPERATURE COEFFICIENTS Unipolar Offset Bipolar Offset Full-Scale Calibration ±1 ±2 ±10 ±0.25 12 12 12 73 69 68 76 –72 71 70 (2) ✻ ✻ ✻ ✻ ✻ –75 LSB % of FS LSB LSB Bits dB dB dB dB (5) ±1 ±2 ±12 ✻ ✻ ✻ ±1/2 CONVERSION TIME (Including Acquisition Time) tAQ + tC at 25°C: 8-Bit Cycle 12-Bit Cycle 12-Bit Cycle, TMIN to TMAX: 5.5 7.5 8 ✻ ✻ ✻ 5.9 8 8.5 ✻ ✻ 125 117 ppm/°C ppm/°C ppm/°C ✻ LSB ✻ ✻ ✻ µs µs µs kHz kHz 20 1.6 ✻ ✻ ns µs 300 10 1.4 ✻ ✻ ✻ ps, r ms ns, r ms µs ® ADS774 ±1/2 ±0.37 ±3 ±5 12 78 –77 72 71 –75 LSB LSB LSB % of FS Bits ±1 ±0.47 ±4 ±12 POWER SUPPLY SENSITIVITY Change in Full-Scale Calibration(6) +4.75V < VDD < +5.25V Max Change SAMPLING DYNAMICS Sampling Rate at 25°C T MIN to TMAX Aperture Delay, tAP With VEE = +5V With VEE = 0V to –15V Aperture Uncertainty (Jitter) With VEE = +5V With VEE = 0V to –15V Settling time to 0.01% for Full-Scale Input Change ±1/2 ✻ ±4 ✻ 2 SPECIFICATIONS (CONT) ELECTRICAL At TA = TMIN to TMAX , VDD = +5V, VEE = –15V to +5V, sampling frequency of 117kHz, fIN = 10kHz; unless otherwise specified. ADS774JE, JP, JU PARAMETER MIN TYP ADS774KE, KP, KU MAX MIN TYP MAX UNITS ✻ V V µA pF OUTPUTS DIGITAL (DB11 - DB0, STATUS) Output Codes: Unipolar Bipolar Logic Levels: Logic 0 (ISINK = 1.6mA) Logic 1 (ISOURCE = 500µA) Leakage, Data Bits Only, High-Z State Capacitance INTERNAL REFERENCE VOLTAGE Voltage Source Current Available for External Loads POWER SUPPLY REQUIREMENTS Voltage: VEE (7) VDD Current: IEE (7) (VEE = –15V) IDD Power Dissipation (TMIN to TMAX) (VEE = 0V to +5V) TEMPERATURE RANGE Specification Operating: Storage Temperature Range +2.4 –5 +2.4 0.5 Unipolar Straight Binary (USB) Bipolar Offset Binary (BOB) +0.4 ✻ +5 ✻ 0.1 5 +2.5 –16.5 +4.5 +2.6 ✻ ✻ VDD +5.5 ✻ ✻ ✻ ✻ ✻ ✻ ✻ V mA ✻ ✻ –1 +15 +24 ✻ ✻ ✻ V V mA mA 75 120 ✻ ✻ mW ✻ ✻ ✻ °C °C °C 0 –40 –65 +70 +85 +150 ✻ ✻ ✻ ✻ Same specification as ADS774JE, JP, JU. NOTES: (1) With fixed 50Ω resistor from REF OUT to REF IN. This parameter is also adjustable to zero at +25°C. (2) FS in this specification table means Full Scale Range. That is, for a ±10V input range, FS means 20V; for a 0 to +10V range, FS means 10V. (3) Maximum error at TMIN and TMAX. (4) Based on using VEE = +5V, which is the Control Mode. See the section "S/H Control Mode and ADC774 Emulation Mode." (5) Using internal reference. (6) This is worst case change in accuracy from accuracy with a +5V supply. (7) VEE is optional, and is only used to set the mode for the internal sample/hold. When VEE = –15V, IEE = –1mA typ; when VEE = 0V, IEE = ±5µA typ; when VEE = +5V, IEE = +167µA typ. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 ADS774 ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS VEE to Digital Common ....................................................... +VDD to –16.5V VDD to Digital Common .............................................................. 0V to +7V Analog Common to Digital Common .................................................... ±1V Control Inputs (CE, CS, AO, 12/8, R/C) to Digital Common .................................................. –0.5V to VDD +0.5V Analog Inputs (Ref In, Bipolar Offset, 10VIN ) to Analog Common ...................................................................... ±16.5V 20VIN to Analog Common .................................................................. ±24V Ref Out .......................................................... Indefinite Short to Common, Momentary Short to VDD Max Junction Temperature ............................................................ +165°C Power Dissipation ........................................................................ 1000mW Lead Temperature (soldering,10s) ................................................. +300°C Thermal Resistance, θJA : Plastic DIPs ........................................ 100°C/W SOIC ................................................... 100°C/W This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT SINAD(1) TEMPERATURE RANGE LINEARITY ERROR PACKAGE PACKAGE DRAWING NUMBER(2) ADS774JE ADS774KE ADS774JP ADS774KP ADS774JU ADS774KU 68dB 70dB 68dB 70dB 68dB 70dB 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C 0°C to +70°C ±1LSB ±1/2LSB ±1LSB ±1/2LSB ±1LSB ±1/2LSB 28-Pin 0.3" Plastic DIP 28-Pin 0.3" Plastic DIP 28-Pin 0.6" Plastic DIP 28-Pin 0.6" Plastic DIP 28-Lead SOIC 28-Lead SOIC 246 246 215 215 217 217 NOTES: (1) SINAD is Signal-to-(Noise + Distortion) expressed in dB. (2) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of BurrBrown IC Data Book. CONNECTION DIAGRAM 4 – R/C 5 CE 6 NC* 7 2.5V Ref Out 8 Analog Common 9 2.5V Ref In 10 VEE 11 Clock 2.5V Reference Bipolar 12 Offset 10V Range 13 20V Range 12 Bits – + CDAC 14 *Not Internally Connected ® ADS774 4 Nibble A AO Control Logic 12 Bits Nibble B 3 Three-State Buffers and Control CS Nibble C 2 Power-Up Reset 1 Succesive Approximation Register +5VDC Supply (VDD ) – 12/8 28 STATUS 27 DB11 (MSB) 26 DB10 25 DB9 24 DB8 23 DB7 22 DB6 21 DB5 20 DB4 19 DB3 18 DB2 17 DB1 16 DB0 (LSB) 15 Digital Common TYPICAL PERFORMANCE CURVES At TA = +25°C, VDD = VEE = +5V; Bipolar ±10V Input Range; sampling frequency of 110kHz; unless otherwise specified. All plots use 4096 point FFTs. SIGNAL/(NOISE + DISTORTION) vs INPUT FREQUENCY AND AMBIENT TEMPERATURE FREQUENCY SPECTRUM (±10V, 2kHz Input) 0 75 –20 Signal/(Noise + Distortion) (dB) S/(N + D) = 72.6dB THD = –93.5dB SNR = 72.6dB Magnitude (dB) –40 –60 –80 –100 –55°C 70 +25°C +125°C –120 65 0 10 20 30 40 50 55 0.1 1 Input Frequency (kHz) FREQUENCY SPECTRUM (±10V, 20kHz Input) 0 S/(N + D) = 70.6dB THD = –77.5dB SNR = 71.5dB –20 S/(N + D) = 53.1dB THD = –74.2dB SNR = 53.1dB –20 –40 Magnitude (dB) –40 Magnitude (dB) 100 FREQUENCY SPECTRUM (±1V, 20kHz Input) 0 –60 –80 –100 –60 –80 –100 –120 –120 10 100 20 30 40 50 55 0 20 30 40 Input Frequency (kHz) SPURIOUS FREE DYNAMIC RANGE, SNR AND THD vs INPUT FREQUENCY POWER SUPPLY REJECTION vs SUPPLY RIPPLE FREQUENCY Spurious Free Dynamic Range 90 Total Harmonic Distortion (THD) 80 Signal-to-Noise Ratio (SNR) 70 60 0.1 10 Input Frequency (kHz) Power Supply Rejection Ratio (V/V in dB) 0 Spurious Free Dynamic Range, SNR, THD (dB) 10 Input Frequency (kHz) 1 10 55 80 60 40 20 10 10 100 50 100 1k 10k 100k 1M 10M Supply Ripple Frequency (Hz) Input Frequency (kHz) ® 5 ADS774 THEORY OF OPERATION latch S1 in position “R” or “G”. Similarly, the second approximation is made by connecting S2 to the reference and S3 to GND, and latching S2 according to the output of the comparator. After three successive approximation steps have been made the voltage level at the comparator will be within 1/2LSB of GND, and a digital word which represents the analog input can be determined from the positions of S1, S2 and S3. In the ADS774, the advantages of advanced CMOS technology—high logic density, stable capacitors, precision analog switches—and Burr-Brown’s state of the art laser trimming techniques are combined to produce a fast, low power analog-to-digital converter with internal sample/hold. The charge-redistribution successive-approximation circuitry converts analog input voltages into digital words. OPERATION A simple example of a charge-redistribution A/D converter with only 3 bits is shown in Figure 1. Analog Input Comparator SC 4C Signal S R 2C S1 G C S2 R L o g i c G S3 R BASIC OPERATION Figure 2 shows the minimum connections required to operate the ADS774 in a basic ±10V range in the Control Mode (discussed in detail in a later section.) The falling edge of a Convert Command (a pulse taking pin 5 LOW for a minimum of 25ns) both switches the ADS774 input to the hold state and initiates the conversion. Pin 28 (STATUS) will output a HIGH during the conversion, and falls only after the conversion is completed and the data has been latched on the data output pins (pins 16 to 27.) Thus, the falling edge of STATUS on pin 28 can be used to read the data from the conversion. Also, during conversion, the STATUS signal puts the data output pins in a High-Z state and inhibits the input lines. This means that pulses on pin 5 are ignored, so that new conversions cannot be initiated during the conversion, either as a result of spurious signals or to short-cycle the ADS774. Out G + Reference Input – FIGURE 1. 3-Bit Charge Redistribution A/D. INPUT SCALING Precision laser-trimmed scaling resistors at the input divide standard input ranges (0V to +10V, 0V to +20V, ±5V or ±10V) into levels compatible with the CMOS characteristics of the internal capacitor array. The ADS774 will begin acquiring a new sample as soon as the conversion is completed, even before the STATUS output falls, and will track the input signal until the next conversion is started. The ADS774 is designed to complete a conversion and accurately acquire a new signal in 8.5µs max over the full operating temperature range, so that conversions can take place at a full 117kHz. SAMPLING While sampling, the capacitor array switch for the MSB capacitor (S1) is in position “S”, so that the charge on the MSB capacitor is proportional to the voltage level of the analog input signal. The remaining array switches (S2 and S3) are set to position “G”. Switch SC is closed, setting the comparator input offset to zero. CONTROLLING THE ADS774 The Burr-Brown ADS774 can be easily interfaced to most microprocessor systems and other digital systems. The microprocessor may take full control of each conversion, or the converter may operate in a stand-alone mode, controlled only by the R/C input. Full control consists of selecting an 8- or 12-bit conversion cycle, initiating the conversion, and reading the output data when ready—choosing either 12 bits all at once, or the 8 MSB bits followed by the 4 LSB bits in a left-justified format. The five control inputs (12/8, CS, A0, R/C, and CE) are all TTL/CMOS-compatible. The functions of the control inputs are described in Table II. The control function truth table is shown in Table III. CONVERSION When a conversion command is received, switch S1 is opened to trap a charge on the MSB capacitor proportional to the analog input level at the time of the sampling command, and switch SC is opened to float the comparator input. The charge trapped in the capacitor array can now be moved between the three capacitors in the array by connecting switches S1, S2, and S3 to positions “R” (to connect to the reference) or “G” (to connect to GND), thus changing the voltage generated at the comparator input. STAND-ALONE OPERATION For stand-alone operation, control of the converter is accomplished by a single control line connected to R/C. In this mode CS and A0 are connected to digital common and CE and 12/8 are connected to +5V. The output data are During the first approximation, the MSB capacitor is connected through switch S1 to the reference, while switches S2 and S3 are connected to GND. Depending on whether the comparator output is HIGH or LOW, the logic will then ® ADS774 6 +5V 10µF 1 28 2 27 DB11 (MSB) 3 26 DB10 4 25 DB9 5 24 DB8 6 23 DB7 Status Output Convert Command +5V NC* 50Ω (1) 50Ω 7 22 DB6 ADS774 8 21 DB5 9 20 DB4 10 19 DB3 11 18 DB2 12 17 DB1 Leave Unconnected 13 16 DB0 (LSB) 14 ±10V Analog Input 15 *Not internally connected NOTE: (1) Connect to GND or VEE for Emulation Mode. Connect to +5V for Control Mode. FIGURE 2. Basic ±10V Operation. presented as 12-bit words. The stand-alone mode is used in systems containing dedicated input ports which do not require full bus interface capability. following an 8-bit conversion, the 4LSBs (DB0-DB3) will be LOW (logic 0). A0 is latched because it is also involved in enabling the output buffers. No other control inputs are latched. Conversion is initiated by a HIGH-to-LOW transition of R/C. The three-state data output buffers are enabled when R/C is HIGH and STATUS is LOW. Thus, there are two possible modes of operation; data can be read with either a positive pulse on R/C, or a negative pulse on STATUS. In either case the R/C pulse must remain LOW for a minimum of 25ns. CONVERSION START The converter initiates a conversion based on a transition occurring on any of three logic inputs (CE, CS, and R/C) as shown in Table III. Conversion is initiated by the last of the three to reach the required state and thus all three may be dynamically controlled. If necessary, all three may change state simultaneously, and the nominal delay time is the same regardless of which input actually starts the conversion. If it is desired that a particular input establish the actual start of conversion, the other two should be stable a minimum of 50ns prior to the transition of the critical input. Timing relationships for start of conversion timing are illustrated in Figure 5. The specifications for timing are contained in Table V. Figure 3 illustrates timing with an R/C pulse which goes LOW and returns HIGH during the conversion. In this case, the three-state outputs go to the high-impedance state in response to the falling edge of R/C and are enabled for external access of the data after completion of the conversion. Figure 4 illustrates the timing when a positive R/C pulse is used. In this mode the output data from the previous conversion is enabled during the time R/C is HIGH. A new conversion is started on the falling edge of R/C, and the three-state outputs return to the high-impedance state until the next occurrence of a HIGH R/C pulse. Timing specifications for stand-alone operation are listed in Table IV. The STATUS output indicates the current state of the converter by being in a high state only during conversion. During this time the three state output buffers remain in a high-impedance state, and therefore data cannot be read during conversion. During this period additional transitions of the three digital inputs which control conversion will be ignored, so that conversion cannot be prematurely terminated or restarted. However, if A0 changes state after the beginning of conversion, any additional start conversion transition will latch the new state of A0, possibly resulting in an incorrect conversion length (8 bits vs 12 bits) for that conversion. FULLY CONTROLLED OPERATION Conversion Length Conversion length (8-bit or 12-bit) is determined by the state of the A0 input, which is latched upon receipt of a conversion start transition (described below). If A0 is latched HIGH, the conversion continues for 8 bits. The full 12-bit conversion will occur if A0 is LOW. If all 12 bits are read ® 7 ADS774 Binary (BIN) Output Input Voltage Range and LSB Values Defined As: ±10V ±5V 0V to +10V 0V to +20V FSR 2n n=8 n = 12 20V 2n 78.13mV 4.88mV 10V 2n 39.06mV 2.44mV 10V 2n 39.06mV 2.44mV 20V 2n 78.13mV 4.88mV + Full-Scale Calibration Midscale Calibration (Bipolar Offset) Zero Calibration ( – Full-Scale Calibration) +10V – 3/2LSB 0V – 1/2LSB –10V + 1/2LSB +5V – 3/2LSB 0V – 1/2LSB –5V + 1/2LSB +10V – 3/2LSB +5V – 1/2LSB 0V +1/2LSB +20V – 3/2LSB +10V – 1/2LSB 0V +1/2LSB Analog Input Voltage Range One Least Significant Bit (LSB) Output Transition Values FFEH to FFFH 7FFFH to 800H 000H to 001H TABLE I. Input Voltages, Transition Values, and LSB Values. DESIGNATION DEFINITION FUNCTION CE (Pin 6) Chip Enable (active high) Must be HIGH (“1”) to either initiate a conversion or read output data. 0-1 edge may be used to initiate a conversion. CS (Pin 3) Chip Select (active low) Must be LOW (“0”) to either initiate a conversion or read output data. 1-0 edge may be used to initiate a conversion. R/C (Pin 5) Read/Convert (“1” = read) (“0” = convert) Must be LOW (“0”) to initiate either 8- or 12-bit conversions. 1-0 edge may be used to initiate a conversion. Must be HIGH (“1”) to read output data. 0-1 edge may be used to initiate a read operation. AO (Pin 4) Byte Address Short Cycle In the start-convert mode, AO selects 8-bit (AO = “1”) or 12-bit (AO = “0”) conversion mode. When reading output data in two 8-bit bytes, AO = “0” accesses 8 MSBs (high byte) and AO = “1” accesses 4 LSBs and trailing “0s” (low byte). Data Mode Select (“1” = 12 bits) (“0” = 8 bits) When reading output data, 12/8 = “1” enables all 12 output bits simultaneously. 12/8 = “0” will enable the MSBs or LSBs as determined by the AO line. 12/8 (Pin 2) TABLE II. Control Line Functions. CE CS R/C 12/8 AO OPERATION 0 X ↑ ↑ 1 1 1 1 1 1 1 X 1 0 0 ↓ ↓ 0 0 0 0 0 X X 0 0 0 0 ↓ ↓ X X X X X X X X 1 0 0 X X 0 1 0 1 0 1 X 0 1 None None Initiate 12-bit conversion Initiate 8-bit conversion Initiate 12-bit conversion Initiate 8-bit conversion Initiate 12-bit conversion Initiate 8-bit conversion Enable 12-bit output Enable 8 MSBs only Enable 4 LSBs plus 4 trailing zeroes 1 1 1 TABLE III. Control Input Truth Table. READING OUTPUT DATA When 12/8 is LOW, the data is presented in the form of two 8-bit bytes, with selection of the byte of interest accomplished by the state of A0 during the read cycle. When A0 is LOW, the byte addressed contains the 8MSBs. When A0 is HIGH, the byte addressed contains the 4LSBs from the conversion followed by four logic zeros which have been forced by the control logic. The left-justified formats of the two 8-bit bytes are shown in Figure 7. Connection of the ADS774 to an 8-bit bus for transfer of the data is illustrated in Figure 8. The design of the ADS774 guarantees that the A0 input may be toggled at any time with no damage to the converter; the outputs which are tied together in Figure 8 cannot be enabled at the same time. The A0 input is usually driven by the least significant bit of the address bus, allowing storage of the output data word in two consecutive memory locations. After conversion is initiated, the output data buffers remain in a high-impedance state until the following four logic conditions are simultaneously met: R/C HIGH, STATUS LOW, CE HIGH, and CS LOW. Upon satisfaction of these conditions the data lines are enabled according to the state of inputs 12/8 and A0. See Figure 6 and Table V for timing relationships and specifications. In most applications the 12/8 input will be hard-wired in either the HIGH or LOW condition, although it is fully TTL and CMOS-compatible and may be actively driven if desired. When 12/8 is HIGH, all 12 output lines (DB0-DB11) are enabled simultaneously for full data word transfer to a 12-bit or 16-bit bus. In this situation the A0 state is ignored when reading the data. ® ADS774 8 tHRL R/C R/C tDS tHRH STATUS STATUS tCONVERSION tHDR tHDR tDDR tCONVERSION tHS High-Z DB11-DB0 High-Z-State DB11-DB0 tDS Data Valid High-Z-State Data Valid Data Valid FIGURE 3. R/C Pulse Low—Outputs Enabled After Conversion. SYMBOL FIGURE 4. R/C Pulse High — Outputs Enabled Only While R/C Is High. PARAMETER tHRL tDS tHDR tHRH tDDR MIN Low R/C Pulse Width STS Delay from R/C Data Valid After R/C Low High R/C Pulse Width Data Access Time TYP MAX UNITS 25 150 ns ns ns ns ns TYP MAX UNITS 60 30 20 20 0 20 200 ns ns ns ns ns ns ns ns 150 ns ns ns ns ns ns ns ns ns ns 200 25 100 TABLE IV. Stand-Alone Mode Timing. (TA = TMIN to TMAX ). SYMBOL PARAMETER Convert Mode tDSC tHEC tSSC tHSC tSRC tHRC tSAC tHAC MIN STS delay from CE CE Pulse width CS to CE setup CS low during CE high R/C to CE setup R/C low during CE high AO to CE setup AO valid during CE high Read Mode tDD tHD tHL tSSR tSRR tSAR tHSR tHRR tHAR tHS 50 50 50 50 50 0 50 Access time from CE Data valid after CE low Output float delay CS to CE setup R/C to CE setup AO to CE setup CS valid after CE low R/C high after CE low AO valid after CE low STATUS delay after data valid 25 50 0 50 0 0 50 75 20 75 35 100 0 150 25 150 375 TABLE V. Timing Specifications, Fully Controlled Operation. (TA = TMIN to TMAX ). CE tHEC CE tSSR tSSC tHSR CS CS tHRR tHSC R/C R/C tSSR tHRC tSRC A0 A0 tSAC Status tHAC Status tHAR t X* tDSC DB11-DB0 tSAR tHS High Impedance DB11-DB0 * tX includes tAQ + tC in ADC774 Emulation Mode, tC only in S/H Control Mode. High-Z Data Valid tDD FIGURE 5. Conversion Cycle Timing. tHD tHL FIGURE 6. Read Cycle Timing. ® 9 ADS774 Word 1 Word 2 Processor DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Converter DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 0 0 STATUS 28 DB11 (MSB) 27 FIGURE 7. 12-Bit Data Format for 8-Bit Systems. 2 12/8 4 AO 26 AO 25 24 Address Bus 23 Data Bus 22 ADS774 21 20 19 18 17 DB0 (LSB) 16 Digital Common 15 FIGURE 8. Connection to an 8-Bit Bus. S/H CONTROL MODE AND ADC774 EMULATION MODE tion is made about the input level after the convert command arrives, since the input signal is sampled and conversion begins immediately after the convert command. This means that a convert command can also be used to switch an input multiplexer or change gains on a programmable gain amplifier, allowing the input signal to settle before the next acquisition at the end of the conversion. Because aperture jitter is minimized in the Control Mode, a high input frequency can be converted without an external sample/hold. The Emulation Mode allows the ADS774 to be dropped into most existing ADC774 sockets without changes to other system hardware or software. In existing sockets, the analog input is held stable during the conversion period so that accurate conversions can proceed, but the input can change rapidly at any time before the conversion starts. The Emulation Mode uses the stability of the analog input during the conversion period to both acquire and convert in a maximum of 8µs (8.5µs over temperature.) In fact, system throughput can be increased, since the input to the ADS774 can start slewing before the end of a conversion (after the acquisition time), which is not possible with existing ADC774s. In the Emulation Mode, a delay time is introduced between the convert command and the start of conversion to allow the ADS774 enough time to acquire the input signal before converting. This increases the effective aperture delay time from 0.02µs to 1.6µs, but allows the ADS774 to replace the ADC774 in most circuits without additional changes. In designs where the input to the ADS774 is changing rapidly in the 200ns prior to a convert command, system performance may be enhanced by delaying the convert command by 200ns. The Control Mode is provided to allow full use of the internal sample/hold, eliminating the need for an external sample/hold in most applications. As compared with systems using separate sample/hold and A/D, the ADS774 in the Control Mode also eliminates the need for one of the control signals, usually the convert command. The command that puts the internal sample/hold in the hold state also initiates a conversion, reducing timing constraints in many systems. When using the ADS774 in the Emulation Mode to replace existing converters in current designs, a sample/hold amplifier often precedes the converter. In these cases, no additional delay in the convert command will be needed. The existing sample/hold will not be slewing excessively when going from the sample mode to the hold mode prior to a conversion. The basic difference between these two modes is the assumptions about the state of the input signal both before and during the conversion. The differences are shown in Figure 9 and Table VI. In the Control Mode, it is assumed that during the required 1.4µs acquisition time the signal is not changing faster than the ADS774 can track. No assump- In both modes, as soon as the conversion is completed the internal sample/hold circuit immediately begins slewing to track the input signal. ® ADS774 10 INSTALLATION In particular, the unused input pin should not be connected to any capacitive load, including high impedance switches. Even a few pF on the unused pin can degrade acquisition time. LAYOUT PRECAUTIONS Analog (pin 9) and digital (pin 15) commons are not connected together internally in the ADS774, but should be connected together as close to the unit as possible and to an analog common ground plane beneath the converter on the component side of the board. In addition, a wide conductor pattern should run directly from pin 9 to the analog supply common, and a separate wide conductor pattern from pin 15 to the digital supply common. Coupling between analog input and digital lines should be minimized by careful layout. For instance, if the lines must cross, they should do so at right angles. Parallel analog and digital lines should be separated from each other by a pattern connected to common. If external full scale and offset potentiometers are used, the potentiometers and associated resistors should be as close as possible to the ADS774. If the single-point system common cannot be established directly at the converter, pin 9 and pin 15 should still be connected together at the converter. A single wide conductor pattern then connects these two pins to the system common. In either case, the common return of the analog input signal should be referenced to pin 9 of the ADC. This prevents any voltage drops that might occur in the power supply common returns from appearing in series with the input signal. POWER SUPPLY DECOUPLING On the ADS774, +5V (to Pin 1) is the only power supply required for correct operation. Pin 7 is not connected internally, so there is no problem in existing ADC774 sockets where this is connected to +15V. Pin 11 (VEE) is only used as a logic input to select modes of control over the sampling function as described above. When used in an existing ADC774 socket, the –15V on pin 11 selects the ADC774 Emulation Mode. Since pin 11 is used as a logic input, it is immune to typical supply variations. The speed of the ADS774 requires special caution regarding whichever input pin is unused. For 10V input ranges, pin 14 (20V Range) must be unconnected, and for 20V input ranges, pin 13 (10V Range) must be unconnected. In both cases, the unconnected input should be shielded with ground plane to reduce noise pickup. S/H CONTROL MODE (Pin 11 Connected to +5V) SYMBOL PARAMETER TYP MAX tAQ + tC Throughput Time: 12-bit Conversions 8-bit Conversions 8 6 8.5 6.3 Conversion Time: 12-bit Conversions 8-bit Conversions Acquisition Time Aperture Delay Aperture Uncertainty 6.4 4.4 1.4 20 0.3 tC tAQ tAP tJ MIN ADC774 EMULATION MODE (Pin 11 Connected to 0V to –15V) MIN TYP MAX UNITS 8 6 8.5 6.3 µs µs µs µs µs ns ns 6.4 4.4 1.4 1600 10 TABLE VI. Conversion Timing, TMIN to TMAX. R/C tC tAP S/H Control Mode Pin 11 connected to +5V. Signal Acquisition Conversion tAQ Signal Acquisition tC tAP ADC774 Emulation Mode* Pin 11 connected to VEE or ground. Signal Acquisition Conversion Signal Acquisition tAQ *In the ADC774 Emulation Mode, a convert command triggers a delay that allows the ADS774 enough time to acquire the input signal before converting. FIGURE 9. Signal Acquisition and Conversion Timing. ® 11 ADS774 connected either to Pin 9 (Analog Common) for unipolar operation, or to Pin 8 (2.5V Ref Out), or the external reference, for bipolar operation. Full-scale and offset adjustments are described below. +VCC Unipolar Offset Adjust R1 100kΩ Full-Scale Adjust R2 10 Ref In 8 Ref Out 12 Bipolar Offset The input impedance of the ADS774 is typically 50kΩ in the 20V ranges and 12kΩ in the 10V ranges. This is significantly higher than that of traditional ADC774 architectures, reducing the load on the input source in most applications. 100Ω ADS774 100kΩ 2.5V –VCC 100Ω R3 INPUT STRUCTURE Figure 12 shows the resistor divider input structure of the ADS774. Since the input is driving a capacitor in the CDAC during acquisition, the input is looking into a high impedance node as compared with traditional ADC774 architectures, where the resistor divider network looks into a comparator input node at virtual ground. 10V Range 13 Analog Input 14 20V Range 9 To understand how this circuit works, it is necessary to know that the input range on the internal sampling capacitor is from 0V to +3.33V, and the analog input to the ADS774 must be converted to this range. Unipolar 20V range can be used as an example of how the divider network functions. In 20V operation, the analog input goes into pin 14. Pin 13 is left unconnected and pin 12 is connected to pin 9, analog common. From Figure 12, it is clear that the input to the capacitor array will be the analog input voltage on pin 14 divided by the resistor network (42kΩ + 42kΩ || 10.5kΩ). A 20V input at pin 14 is divided to 3.33V at the capacitor array, while a 0V input at pin 14 gives 0V at the capacitor array. Analog Common FIGURE 10. Unipolar Configuration. Full-Scale Adjust R2 10 Ref In 8 Ref Out 12 Bipolar Offset 100Ω ADS774 2.5V 100Ω Bipolar Offset Adjust R1 Analog Input 10V Range 20V Range The main effect of the 10kΩ internal resistor on pin 12 is to provide the same offset adjust response as that of traditional ADC774 architectures without changing the external trimpot values. 13 14 SINGLE SUPPLY OPERATION The ADS774 is designed to operate from a single +5V supply, and handle all of the unipolar and bipolar input ranges, in either the Control Mode or the Emulation Mode as described above. Pin 7 is not connected internally. This is 9 Analog Common FIGURE 11. Bipolar Configuration. The +5V supply should be bypassed with a 10µF tantalum capacitor located close to the converter to promote noisefree operations, as shown in Figure 2. Noise on the power supply lines can degrade the converter’s performance. Noise and spikes from a switching power supply are especially troublesome. 42kΩ Pin 13 21kΩ 10V Range Capacitor Array* 21kΩ RANGE CONNECTIONS The ADS774 offers four standard input ranges: 0V to +10V, 0V to +20V, ±5V, or ±10V. Figures 10 and 11 show the necessary connections for each of these ranges, along with the optional gain and offset trim circuits. If a 10V input range is required, the analog input signal should be connected to pin 13 of the converter. A signal requiring a 20V range is connected to pin 14. In either case the other pin of the two is left unconnected. Pin 12 (Bipolar Offset) is Pin 12 Bipolar Offset 10.5kΩ 10kΩ *10pF when sampling FIGURE 12. ADS774 Input Structure. ® ADS774 Pin 14 20V Range 12 where +12V or +15V is supplied on traditional ADC774s. Pin 11, the –12V or –15V supply input on traditional ADC774s, is used only as a logic input on the ADS774. There is a resistor divider internally on pin 11 to reduce that input to a correct logic level within the ADS774, and this resistor will add 10mW to 15mW to the power consumption of the ADS774 when –15V is supplied to pin 11. To minimize power consumption in a system, pin 11 can be simply grounded (for Emulation Mode) or tied to +5V (for Control Mode.) If adjustment is required, connect the converter as shown in Figure 10. Sweep the input through the end-point transition voltage (0V + 1/2LSB; +1.22mV for the 10V range, +2.44mV for the 20V range) that causes the output code to be DB0 ON (HIGH). Adjust potentiometer R1 until DB0 is alternately toggling ON and OFF with all other bits OFF. Then adjust full scale by applying an input voltage of nominal full-scale minus 3/2LSB, the value which should cause all bits to be ON. This value is +9.9963V for the 10V range and +19.9927V for the 20V range. Adjust potentiometer R2 until bits DB1DB11 are ON and DB0 is toggling ON and OFF. There are no other modifications required for the ADS774 to function with a single +5V supply. CALIBRATION PROCEDURE—BIPOLAR RANGES If external adjustments of full-scale and bipolar offset are not required, replace the potentiometers in Figure 11 by 50Ω, 1% metal film resistors. CALIBRATION OPTIONAL EXTERNAL FULL-SCALE AND OFFSET ADJUSTMENTS If adjustments are required, connect the converter as shown in Figure 11. The calibration procedure is similar to that described above for unipolar operation, except that the offset adjustment is performed with an input voltage which is 1/2LSB above the minus full-scale value (–4.9988V for the ±5V range, –9.9976V for the ±10V range). Adjust R1 for DB0 to toggle ON and OFF with all other bits OFF. To adjust full-scale, apply a DC input signal which is 3/2LSB below the nominal plus full-scale value (+4.9963V for ±5V range, +9.9927V for ±10V range) and adjust R2 for DB0 to toggle ON and OFF with all other bits ON. Offset and full-scale errors may be trimmed to zero using external offset and full-scale trim potentiometers connected to the ADS774 as shown in Figures 10 and 11 for unipolar and bipolar operation. CALIBRATION PROCEDURE— UNIPOLAR RANGES If external adjustments of full-scale and offset are not required, replace R2 in Figure 10 with a 50Ω 1% metal film resistor and connect pin 12 to pin 9, omitting the other adjustment components. ® 13 ADS774