Ultra Low Power/High Speed CMOS SRAM 512K X 16 bit BSI BH616UV8010 n FEATURES n DESCRIPTION Ÿ Wide VCC low operation voltage : 1.65V ~ 3.6V Ÿ Ultra low power consumption : VCC = 3.0V Operation current : 5.0mA at 70ns at 25OC 1.5mA at 1MHz at 25OC Standby current : 2.5uA at 25OC VCC = 2.0V Data retention current : 2.5uA at 25OC Ÿ High speed access time : -70 70ns at 1.8V at 85OC Ÿ Automatic power down when chip is deselected Ÿ Easy expansion with CE1, CE2 and OE options Ÿ I/O Configuration x8/x16 selectable by LB and UB pin. Ÿ Three state outputs and TTL compatible Ÿ Fully static operation, no clock, no refreash Ÿ Data retention supply voltage as low as 1.0V The BH616UV8010 is a high performance, ultra low power CMOS Static Random Access Memory organized as 524,288 by 16 bits and operates in a wide range of 1.65V to 3.6V supply voltage. Advanced CMOS technology and circuit techniques provide both high speed and low power features with typical operating current of 1.5mA at 1MHz at 3.6V/25OC and maximum access time of 70ns at 1.8V/85OC. Easy memory expansion is provided by an active LOW chip enable (CE1), an active HIGH chip enable (CE2) and active LOW output enable (OE) and three-state output drivers. The BH616UV8010 has an automatic power down feature, reducing the power consumption significantly when chip is deselected. The BH616UV8010 is available in DICE form, JEDEC standard 48-pin TSOP-I and 48-ball BGA package. n PRODUCT FAMILY PRODUCT FAMILY OPERATING TEMPERATURE VCC RANGE POWER CONSUMPTION SPEED (ns) VCC=1.8~3.6V BH616UV8010DI +0OC to +70OC (ICC, Max) PKG TYPE 13uA 10uA 10mA 7mA 1.65V ~ 3.6V O 70 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 BH616UV8010TC BH616UV8010TI 1 2 3 15uA 12uA 10mA 7mA BGA-48-0608 n BLOCK DIAGRAM n PIN CONFIGURATIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DICE TSOP1-48 O -25 C to +85 C BH616UV8010AI A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE CE2 NC UB LB A18 A17 A7 A6 A5 A4 A3 A2 A1 Operating (ICCSB1, Max) VCC=3.6V VCC=1.8V VCC=3.6V VCC=1.8V 70 BH616UV8010TI STANDBY 4 5 A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE VSS CE1 A0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 Address Row Buffer Decoder . . . . . . 16 . . . . 16 . OE A0 A1 A2 CE2 B DQ8 UB A3 A4 CE1 DQ0 C DQ9 DQ10 A5 A6 DQ1 DQ2 D VSS DQ11 A17 A7 DQ3 VCC E VCC DQ12 VSS A16 DQ4 VSS F DQ14 DQ13 A14 A15 DQ5 DQ6 G DQ15 NC A12 A13 WE DQ7 H A18 A8 A9 A10 A11 NC 1024 x 8192 CE2 CE1 WE OE UB LB VCC VSS 16 Data Input Buffer Data Output Buffer Column I/O Write Driver Sense Amp 16 512 Column Decoder DQ15 LB Memory Array 8192 DQ0 . 6 A 1024 10 Input 9 Address Input Buffer Control A18 A17 A15 A14 A13 A16 A2 A1 A0 48-ball BGA top view Brilliance Semiconductor, Inc. reserves the right to modify document contents without notice. Detailed product characteristic test report is available upon request and being accepted. R0201-BH616UV8010 1 Revision 1.0 Jul. 2005 BSI BH616UV8010 n PIN DESCRIPTIONS Name Function A0-A18 Address Input These 19 address inputs select one of the 524,288 x 16 bit in the RAM CE1 Chip Enable 1 Input CE2 Chip Enable 2 Input CE1 is active LOW and CE2 is active HIGH. Both chip enables must be active when data read from or write to the device. If either chip enable is not active, the device is deselected and is in standby power mode. The DQ pins will be in the high impedance state when the device is deselected. WE Write Enable Input The write enable input is active LOW and controls read and write operations. With the chip selected, when WE is HIGH and OE is LOW, output data will be present on the DQ pins; when WE is LOW, the data present on the DQ pins will be written into the selected memory location. OE Output Enable Input The output enable input is active LOW. If the output enable is active while the chip is selected and the write enable is inactive, data will be present on the DQ pins and they will be enabled. The DQ pins will be in the high impendence state when OE is inactive. LB and UB Data Byte Control Input Lower byte and upper byte data input/output control pins. DQ0-DQ15 Data Input/Output Ports VCC 16 bi-directional ports are used to read data from or write data into the RAM. VSS Ground Power Supply n TRUTH TABLE MODE Chip De-selected (Power Down) Output Disabled Read Write CE1 CE2 WE OE LB UB H X X X X X High Z High Z ICCSB, ICCSB1 X L X X X X High Z High Z ICCSB, ICCSB1 X X X X H H High Z High Z ICCSB, ICCSB1 L H H H X X High Z High Z ICC L L DOUT DOUT ICC H L High Z DOUT ICC L H DOUT High Z ICC L L DIN DIN ICC H L X DIN ICC L H DIN X ICC L L H H H L L X DQ0~DQ7 DQ8~DQ15 VCC CURRENT NOTES: H means VIH; L means VIL; X means don’t care (Must be VIH or VIL state) R0201-BH616UV8010 2 Revision 1.0 Jul. 2005 BSI BH616UV8010 (1) n ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER Terminal Voltage with Respect to GND Temperature Under Bias VTERM TBIAS TSTG Storage Temperature n OPERATING RANGE RATING (2) -0.5 to 4.6V UNITS V -40 to +125 O C -60 to +150 O C PT Power Dissipation 1.0 W IOUT DC Output Current 20 mA AMBIENT TEMPERATURE RANG O VCC O Commercial 0 C to + 70 C 1.65V ~ 3.6V Industrial -25OC to + 85OC 1.65V ~ 3.6V n CAPACITANCE (1) O (TA = 25 C, f = 1.0MHz) SYMBOL PAMAMETER CONDITIONS 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. –2.0V in case of AC pulse width less than 30 ns MAX. Input VIN = 0V 6 Capacitance Input/Output CIO VI/O = 0V 8 Capacitance 1. This parameter is guaranteed and not 100% tested. CIN O UNITS pF pF O n DC ELECTRICAL CHARACTERISTICS (TA = -25 C to +85 C) PARAMETER NAME PARAMETER VCC Power Supply VIL Input Low Voltage TEST CONDITIONS VCC=1.8V MIN. TYP.(1) MAX. UNITS 1.65 -- 3.6 V -0.3(2) -- Input High Voltage IIL Input Leakage Current ILO Output Leakage Current VOL Output Low Voltage VCC=1.8V 1.4 VCC=3.6V 2.0 VIN = 0V to VCC, CE1 = VIH or CE2 = VIL V 0.8 VCC=3.6V VIH 0.4 -- VCC+0.3(3) V -- -- 1 uA -- -- 1 uA -- -- VI/O = 0V to V CC, VOH Output High Voltage ICC ICC1 ICCSB ICCSB1 (5) CE1 = VIH or CE2 = VIL or OE = VIH or UB = LB = VIH V CC = Max, IOL = 0.2mA VCC=1.8V V CC = Max, IOL = 2.0mA VCC=3.6V V CC = Min, IOH = -0.1mA VCC=1.8V VCC-0.2 V CC = Min, IOH = -1.0mA VCC=3.6V 2.4 Operating Power Supply Current CE1 = VIL and CE2 = VIH, IDQ = 0mA, f = FMAX(4) Operating Power Supply Current CE1 = VIL and CE2 = VIH, IDQ = 0mA, f = 1MHz Standby Current – TTL CE1 = VIH, or CE2 = VIL, IDQ = 0mA Standby Current – CMOS CE1≧VCC-0.2V or CE2≦0.2V, VIN≧V CC-0.2V or VIN≦0.2V VCC=1.8V -- -- VCC=3.6V VCC=1.8V -- -- VCC=3.6V -- 4.5 7 5.0 10 1.0 1.5 1.5 2.0 -- 0.5 V mA mA mA 1.0 VCC=3.6V VCC=1.8V V 0.4 VCC=3.6V VCC=1.8V 0.2 -- 2.5 12 2.5 15 uA 1. Typical characteristics are at TA=25OC. 2. Undershoot: -1.0V in case of pulse width less than 20 ns. 3. Overshoot: VCC+1.0V in case of pulse width less than 20 ns. 4. FMAX=1/tRC. 5. ICCSB1(MAX.) is 10uA/13uA at VCC=1.8V/3.6V and TA=0OC ~ 70OC. R0201-BH616UV8010 3 Revision 1.0 Jul. 2005 BSI BH616UV8010 O O n DATA RETENTION CHARACTERISTICS (TA = -25 C to +85 C) SYMBOL VDR (3) ICCDR PARAMETER TEST CONDITIONS VCC for Data Retention CE1≧VCC-0.2V or CE2≦0.2V, VIN≧VCC-0.2V or VIN≦0.2V Data Retention Current CE1≧VCC-0.2V or CE2≦0.2V, VIN≧VCC-0.2V or VIN≦0.2V Chip Deselect to Data Retention Time tCDR tR MIN. TYP. (1) MAX. UNITS 1.0 -- -- V 0.5 3.0 2.5 12 0 -- -- ns tRC (2) -- -- ns VCC=1.0V -- VCC=2.0V uA See Retention Waveform Operation Recovery Time 1. TA=25OC. 2. tRC = Read Cycle Time. 3. ICCDR(MAX.) is 2.5uA /10uA at VCC=1.0V/2.0V and TA=0OC ~ 70OC. n LOW VCC DATA RETENTION WAVEFORM (1) (CE1 Controlled) Data Retention Mode VCC VDR≧1.0V VCC tCDR tR CE1≧VCC - 0.2V VIH CE1 VCC VIH n LOW VCC DATA RETENTION WAVEFORM (2) (CE2 Controlled) Data Retention Mode VDR≧1.0V VCC VCC tCDR VCC tR CE2≦0.2V CE2 VIL VIL n AC TEST CONDITIONS n KEY TO SWITCHING WAVEFORMS (Test Load and Input/Output Reference) Input Pulse Levels VCC / 0V Input Rise and Fall Times 1V/ns Input and Output Timing Reference Level tCLZ1, tCLZ2, tBE, tOLZ, tCHZ1, tCHZ2, tBDO, tOHZ, tWHZ, tOW Output Load Others WAVEFORM 0.5Vcc CL = 5pF+1TTL Output CL(1) VCC GND OUTPUTS MUST BE STEADY MUST BE STEADY MAY CHANGE FROM “H” TO “L” WILL BE CHANGE FROM “H” TO “L” MAY CHANGE FROM “L” TO “H” WILL BE CHANGE FROM “L” TO “H” DON’T CARE ANY CHANGE PERMITTED CHANGE : STATE UNKNOW DOES NOT APPLY CENTER LINE IS HIGH INPEDANCE “OFF” STATE CL = 30pF+1TTL ALL INPUT PULSES 1 TTL INPUTS 90% 10% → ← Rise Time: 1V/ns 90% 10% → ← Fall Time: 1V/ns 1. Including jig and scope capacitance. R0201-BH616UV8010 4 Revision 1.0 Jul. 2005 BSI BH616UV8010 O O n AC ELECTRICAL CHARACTERISTICS (TA = -25 C to +85 C) READ CYCLE JEDEC PARAMETER NAME PARANETER NAME tAVAX tRC tAVQX tAA tE1LQV tACS1 Chip Select Access Time tE2LQV tACS2 Chip Select Access Time CYCLE TIME : 70ns DESCRIPTION UNITS MIN. TYP. MAX. Read Cycle Time 70 -- -- ns Address Access Time -- -- 70 ns (CE1) -- -- 70 ns (CE2) -- -- 70 ns (LB, UB) -- -- 70 ns -- -- 30 ns tBLQV tBA Data Byte Control Access Time tGLQV tOE Output Enable to Output Valid tE1LQX tCLZ1 Chip Select to Output Low Z (CE1) 10 -- -- ns tE2LQX tCLZ2 Chip Select to Output Low Z (CE2) 10 -- -- ns tBLQX tBE Data Byte Control to Output Low Z (LB, UB) 10 -- -- ns tGLQX tOLZ Output Enable to Output Low Z 5 -- -- ns tE1HQZ tCHZ1 Chip Select to Output High Z (CE1) -- -- 25 ns tE2HQZ tCHZ2 Chip Select to Output High Z (CE2) -- -- 25 ns tBHQZ tBDO Data Byte Control to Output High Z (LB, UB) -- -- 25 ns tGHQZ tOHZ Output Enable to Output High Z -- -- 25 ns tAVQX tOH Data Hold from Address Change 10 -- -- ns n SWITCHING WAVEFORMS (READ CYCLE) READ CYCLE 1 (1,2,4) tRC ADDRESS tOH tAA tOH DOUT R0201-BH616UV8010 5 Revision 1.0 Jul. 2005 BSI READ CYCLE 2 BH616UV8010 (1,3,4) CE1 tACS1 CE2 (6) tACS2 tCLZ tCHZ (5,6) (5, 6) DOUT READ CYCLE 3 (1, 4) tRC ADDRESS tAA OE tOH tOE tOLZ CE1 (5) tACS1 tCLZ1 CE2 (5) tOHZ tCHZ (5) (1,5) tACS2 tCLZ2 tCHZ2 (2,5) tBA LB, UB tBE tBDO DOUT NOTES: 1. WE is high in read Cycle. 2. Device is continuously selected when CE1 = VIL and CE2= VIH. 3. Address valid prior to or coincident with CE1 transition low and/or CE2 transition high. 4. OE = VIL. 5. Transition is measured ± 500mV from steady state with CL = 5pF. The parameter is guaranteed but not 100% tested. R0201-BH616UV8010 6 Revision 1.0 Jul. 2005 BSI BH616UV8010 O O n AC ELECTRICAL CHARACTERISTICS (TA = -25 C to +85 C) WRITE CYCLE JEDEC PARAMETER NAME PARANETER NAME tAVAX tWC tAVWL CYCLE TIME : 70ns DESCRIPTION UNITS MIN. TYP. MAX. Write Cycle Time 70 -- -- ns tAS Address Set up Time 0 -- -- ns tAVWH tAW Address Valid to End of Write 50 -- -- ns tELWH tCW Chip Select to End of Write 50 -- -- ns tBLWH tBW Data Byte Control to End of Write 50 -- -- ns tWLWH tWP Write Pulse Width 35 -- -- ns tWHAX tWR1 Write Recovery Time (CE1, WE) 0 -- -- ns tE2LAX tWR2 Write Recovery Time (CE2) 0 -- -- ns tWLQZ tWHZ Write to Output High Z -- -- 20 ns tDVWH tDW Data to Write Time Overlap 30 -- -- ns tWHDX tDH Data Hold from Write Time 0 -- -- ns tGHQZ tOHZ Output Disable to Output in High Z -- -- 25 ns tWHQX tOW End of Write to Output Active 5 -- -- ns (LB, UB) n SWITCHING WAVEFORMS (WRITE CYCLE) (1) WRITE CYCLE 1 tWC ADDRESS OE tCW CE1 (5) CE2 (5) tCW tWR1 (11) (3) (11) tWR2 tBW (3) LB, UB tAW WE tWP tAS tOHZ (2) (4,10) DOUT tDH tDW DIN R0201-BH616UV8010 7 Revision 1.0 Jul. 2005 BSI WRITE CYCLE 2 BH616UV8010 (1,6) tWC ADDRESS (5) CE1 CE2 tCW (11) tCW (11) (5) (12) LB, UB tAW tWP WE tAS tWHZ tWR tBW (3) (2) (4,10) tOW (7) (8) DOUT tDW tDH (8,9) DIN NOTES: 1. WE must be high during address transitions. 2. The internal write time of the memory is defined by the overlap of CE1 and CE2 active and WE low. All signals must be active to initiate a write and any one signal can terminate a write by going inactive. The data input setup and hold timing should be referenced to the second transition edge of the signal that terminates the write. 3. tWR is measured from the earlier of CE1 or WE going high or CE2 going low at the end of write cycle. 4. During this period, DQ pins are in the output state so that the input signals of opposite phase to the outputs must not be applied. 5. If the CE1 low transition or the CE2 high transition occurs simultaneously with the WE low transitions or after the WE transition, output remain in a high impedance state. 6. OE is continuously low (OE = VIL). 7. DOUT is the same phase of write data of this write cycle. 8. DOUT is the read data of next address. 9. If CE1 is low and CE2 is high during this period, DQ pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 10. Transition is measured ± 500mV from steady state with CL = 5pF. The parameter is guaranteed but not 100% tested. 11. tCW is measured from the later of CE1 going low or CE2 going high to the end of write. R0201-BH616UV8010 8 Revision 1.0 Jul. 2005 BSI BH616UV8010 n ORDERING INFORMATION BH616UV8010 X X Z YY SPEED 70: 70ns PKG MATERIAL -: Normal G: Green GRADE I: -25oC ~ +85oC PACKAGE T: TSOP 1-48 A: BGA-48-0608 D:DICE Note: Brilliance Semiconductor Inc. (BSI) assumes no responsibility for the application or use of any product or circuit described herein. BSI does not authorize its products for use as critical components in any application in which the failure of the BSI product may be expected to result in significant injury or death, including life-support systems and critical medical instruments. n PACKAGE DIMENSIONS n NOTES: 1: CONTROLLING DIMENSIONS ARE IN MILLIMETERS. 1.4 Max. 2: PIN#1 DOT MARKING BY LASER OR PAD PRINT. 3: SYMBOL "N" IS THE NUMBER OF SOLDER BALLS. BALL PITCH e = 0.75 D E N D1 E1 8.0 6.0 48 5.25 3.75 E1 e D1 VIEW A 48 mini-BGA (6 x 8) R0201-BH616UV8010 9 Revision 1.0 Jul. 2005 BSI BH616UV8010 PACKAGE DIMENSIONS TSOP1-48 Pin (12mm x 20mm) R0201-BH616UV8010 10 Revision 1.0 Jul. 2005 BSI BH616UV8010 n Revision History Revision No. History Draft Date Remark 1.0 Initial Production Version July 15,2005 Initial R0201-BH616UV8010 11 Revision 1.0 Jul. 2005