SCDS163A − MAY 2004 − REVISED MAY 2004
D Wide Bandwidth (BW = 300 MHz Min)
D Low Differential Crosstalk
D Data and Control Inputs Provide
D
(XTALK = −60 dB Typ)
D Low Power Consumption (ICC = 3 mA Max)
D Bidirectional Data Flow, With Near-Zero
D
Propagation Delay
Low ON-State Resistance (ron = 3 W Typ)
VCC Operating Range From 6 V to 6.5 V
Ioff Supports Partial-Power-Down Mode
Operation
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
E
ID0
ID1
YD
IC0
IC1
YC
IA0
IA1
YA
IB0
IB1
YB
VCC
1
1
16
PW PACKAGE
(TOP VIEW)
NC
S
IA0
IA1
YA
IB0
IB1
YB
GND
NC
15 E
14 ID0
2
3
13 ID1
12 YD
4
5
6
7
8
9
YC
S
IA0
IA1
YA
IB0
IB1
YB
GND
RGY PACKAGE
(TOP VIEW)
S
D OR DBQ PACKAGE
(TOP VIEW)
D
GND
D
D
D
Undershoot Clamp Diode
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
Suitable for Both 10 Base-T/100 Base-T
Signaling
11 IC0
10 IC1
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
NC
VCC
E
ID0
ID1
YD
IC0
IC1
YC
NC
NC − No internal connection
description/ordering information
The TI TS5L100 LAN switch is a 4-bit 1-of-2 multiplexer/demultiplexer with a single switch-enable (E) input.
When E is low, the switch is enabled and the I port is connected to the Y port. When E is high, the switch is
disabled and the high-impedance state exists between the I and Y ports. The select (S) input controls the data
path of the multiplexer/demultiplexer.
ORDERING INFORMATION
QFN − RGY
SOIC − D
0°C to 70°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
SSOP (QSOP) − DBQ
TSSOP − PW
Tape and reel
TS5L100RGYR
Tube
TS5L100D
Tape and reel
TS5L100DR
Tape and reel
TS5L100DBQR
Tube
TS5L100PW
Tape and reel
TS5L100PWR
TOP-SIDE
MARKING
TG100
TS5L100
TG100
TG100
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2004, Texas Instruments Incorporated
!" #!$% &"'
&! #" #" (" " ") !"
&& *+' &! #", &" ""%+ %!&"
", %% #""'
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCDS163A − MAY 2004 − REVISED MAY 2004
description/ordering information (continued)
This device can be used to replace mechanical relays in LAN applications. This device has low ron, wide
bandwidth, and low differential crosstalk, making it suitable for 10 Base-T, 100 Base-T, and various other LAN
applications.
This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that
damaging current will not backflow through the device when it is powered down. The device has isolation during
power off.
To ensure the high-impedance state during power up or power down, E should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
FUNCTION TABLE
INPUTS
E
INPUT/OUTPUT
YX
S
FUNCTION
L
L
H
IX0
IX1
YX = IX0
L
H
X
Z
Disconnect
YX = IX1
PIN DESCRIPTIONS
PIN NAME
IAn−IDn
S
Select input
E
Enable input
YA−YD
2
DESCRIPTION
Data I/Os
Data I/Os
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS163A − MAY 2004 − REVISED MAY 2004
logic diagram (positive logic)
2
4
IA0
YA
3
IA1
YB
7
5
IB0
6
IB1
9
11
YC
10
YD
12
14
13
S
IC0
IC1
ID0
ID1
1
15
Control
Logic
E
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCDS163A − MAY 2004 − REVISED MAY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input voltage range, VIN (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Switch I/O voltage range, VI/O (see Notes 1, 2, and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input clamp current, IIK (VIN < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
I/O port clamp current, II/OK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
ON-state switch current, II/O (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±128 mA
Continuous current through VCC or GND terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 5): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
(see Note 5): DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90°C/W
(see Note 5): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W
(see Note 6): RGY package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to ground, unless otherwise specified.
2. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
3. VI and VO are used to denote specific conditions for VI/O.
4. II and IO are used to denote specific conditions for II/O.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
6. The package thermal impedance is calculated in accordance with JESD 51-5.
recommended operating conditions (see Note 7)
MIN
MAX
UNIT
VCC
VIH
Supply voltage
6
6.5
V
High-level control input voltage (E, S)
2.5
6.5
V
VIL
TA
Low-level control input voltage (E, S)
0
0.8
V
Operating free-air temperature
0
70
°C
NOTE 7: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS163A − MAY 2004 − REVISED MAY 2004
electrical characteristics over recommended
VCC = 6 V to 6.5 V (unless otherwise noted)
PARAMETER
VIK
Vhys
E, S
operating
free-air
TEST CONDITIONS
VCC = 6 V,
IIN = −18 mA
E = low,
temperature
range,
TYP†
MAX
UNIT
−1.8
V
MIN
E, S
150
VO
IIH
E, S
VI = 4.5 V,
VCC = 6.5 V,
IIL
E, S
VCC = 6.5 V,
RL = 100 Ω, see Figure 11
3.7
mV
4.06
VIN = VCC
VIN = GND
V
±1
µA
±1
µA
±1
µA
IOZ‡
VCC = 6.5 V,
VO = 0 to 6.5 V,
VI = 0,
IOS§
VCC = 6.5 V,
VO = 0 to 0.5 VCC,
VI = 0,
Switch ON
Ioff
ICC
VCC = 0,
VCC = 6.5 V,
VO = 0 to 6.5 V,
II/O = 0,
VI = 0
Switch ON or OFF
1
3
µA
VCC = 6.5 V,
One input at 3.4 V,
Other inputs at VCC or GND
6
mA
VCC = 6.5 V,
I and Y ports open,
VIN input switching 50% duty cycle
0.35
mA/
MHz
∆ICC
E, S
ICCD
CIN
E, S
Y port
CON
M2
mA
3.5
µA
pF
4.5
VI = 0,
f = 1 MHz,
Outputs open,
Switch OFF
VI = 0,
f = 1 MHz,
Outputs open,
Switch ON
VI = 4.5 V,
Switch ON,
RL = 100 Ω, see Figure 11
M1
ron
50
f = 1 MHz
I port
COFF
Switch OFF
pF
6.5
14
pF
7.5
11.2
19
2
3
6
1
2
VI = 4.5 V,
Switch ON
∆ron
VI, VO, II, and IO refer to I/O pins. VIN refers to the control inputs.
† All typical values are at VCC = 6.2 V (unless otherwise noted), TA = 25°C.
‡ For I/O ports, IOZ includes the input leakage current.
§ The IOS test is applicable to only one ON channel at a time. The duration of this test is less than one second.
Ω
Ω
switching characteristics over recommended operating free-air temperature range,
VCC = 6 V to 6.5 V, RL = 100 Ω, CL = 35 pF (unless otherwise noted) (see Figure 7)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tON
S
Y
7
ns
tOFF
S
Y
4
ns
MIN
MAX
UNIT
† All typical values are at VCC = 6.2 V (unless otherwise noted), TA = 25°C.
dynamic characteristics over recommended
VCC = 6 V to 6.5 V (unless otherwise noted)
PARAMETER
operating
TEST CONDITIONS
free-air
temperature
range,
MIN
TYP†
UNIT
−40
−60
dB
dB
MAX
XTALK(Diff)
XTALK
RL = 100 Ω,
f = 10 MHz, see Figure 12,
RL = 100 Ω,
f = 30 MHz, see Figure 9
−50
OIRR
RL = 100 Ω,
f = 30 MHz, see Figure 10
−40
dB
BW
RL = 100 Ω, see Figure 8
350
MHz
tr = tf = 2 ns
† All typical values are at VCC = 6.2 V (unless otherwise noted), TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCDS163A − MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
6
50
45
5
25°C
70°C
40
ron − ON Resistance − Ω
4
30
25
3
VO
20
2
25°C
70°C
15
10
1
ron
5
0
0
0
1
2
3
4
VI − Input Voltage − V
Figure 1. ron and VO vs VI Over Temperature (VCC = 6 V)
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
6
VO − Output Voltage − V
35
SCDS163A − MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
6
50
45
5
ron − ON Resistance − Ω
35
4
30
25
3
VO
20
VO − Output Voltage − V
40
2
15
10
ron
1
5
0
0
0
1
2
3
VI − Input Voltage − V
4
5
6
Figure 2. ron and VO vs VI (VCC = 6.2 V and TA = 255C)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SCDS163A − MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
0
0
−5
−1
Phase
−10
Gain
−3
−15
−20
Gain − dB
−4
−25
−5
−30
−6
−35
−7
−40
−8
−45
−9
1
10
100
Frequency − MHz
Gain −3 dB at 501.2 MHz
Phase at −3-dB Frequency, −31.7 Degrees
Figure 3. Gain/Phase vs Frequency
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
−50
600
Phase − Deg
−2
SCDS163A − MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
0
250
−10
200
150
−20
100
50
−40
0
−50
−50
−60
Phase − Deg
Off Isolation − dB
Phase
−30
−100
Off Isolation
−70
−150
−80
−200
−250
−90
1
10
100
600
Frequency − MHz
Off Isolation at 30 MHz, −52.1 dB
Phase at 30 MHz, 77 Degrees
Figure 4. Off Isolation vs Frequency
0
250
−10
200
−20
150
−40
−50
Phase
Phase − Deg
Crosstalk − dB
−30
100
−60
Crosstalk
−70
50
−80
−90
1
10
100
0
600
Frequency − MHz
Crosstalk at 30 MHz, −54 dB
Phase at 30 MHz, 93.2 Degrees
Figure 5. Crosstalk vs Frequency
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SCDS163A − MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
3
2.5
2
1.5
VI+
VI−
1
0.5
0
Voltage − V
0.01
0.005
Differential
Crosstalk
0
−0.005
−0.01
0.04
0.03
0.02
0.01
0
−0.01
−0.02
−0.03
−0.04
−0.05
23
VO+
VO−
43
63
83
Time − ns
Figure 6. Differential Crosstalk
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
120
SCDS163A − MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
VCC
Input Generator
VS
50 Ω
S
50 Ω
VG1
IX0
DUT
VX0
D
IX1
VO
CL
(see Note A)
E
RL
VX1
TEST
VCC
RL
CL
VX0
VX1
tON
6.2 V
6.2 V
100 Ω
100 Ω
35 pF
35 pF
GND
4.5 V
4.5 V
GND
tOFF
6.2 V
6.2 V
100 Ω
100 Ω
35 pF
35 pF
GND
4.5 V
4.5 V
GND
TEST CIRCUIT
3V
Output
Control
(VIN)
50%
50%
0V
tON
Analog Output
Waveform
(VO)
tOFF
90%
90%
VOH
0V
VOLTAGE WAVEFORMS
tON AND tOFF TIMES
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
C. The outputs are measured one at a time, with one transition per measurement.
Figure 7. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SCDS163A − MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
Network Analyzer
(HP8753ES)
VBIAS
P1
P2
VCC
IA0
YA
RL = 100 Ω
S
DUT
VS
E
VE
Figure 8. Test Circuit for Frequency Response (BW)
Frequency response is measured at the output of the ON channel. For example, when VS = 0, VE = 0, and YA is the
input, the output is measured at IA0. All unused analog I/O ports are left open.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS163A − MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
Network Analyzer
(HP8753ES)
VBIAS
P1
P2
VCC
YA
IA0
RL = 100 Ω
S
50 Ω†
VS
E
DUT
VE
IB0
YB
RL = 100 Ω
† A 50-Ω termination resistor is needed for the network analyzer.
Figure 9. Test Circuit for Crosstalk (XTALK)
Crosstalk is measured at the output of the nonadjacent ON channel. For example, when VS = 0, VE = 0, and YA is
the input, the output is measured at IB0. All unused analog input (Y) ports are connected to GND, and output (A) ports
are connected to GND through 50-Ω pulldown resistors.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SCDS163A − MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
Network Analyzer
(HP8753ES)
VBIAS
P1
P2
VCC
IA0
YA
RL = 100 Ω
S
DUT
VS
IA1
E
RL = 100 Ω
50 Ω†
VE
† A 50-Ω termination resistor is needed for the network analyzer.
Figure 10. Test Circuit for Off Isolation (OIRR)
Off isolation is measured at the output of the OFF channel. For example, when VS = VCC, VE = 0, and YA is the input,
the output is measured at IA0. All unused analog input (Y) ports are left open, and output (A) ports are connected to
GND through 50-Ω pulldown resistors.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS163A − MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
Switch ON
VI = 4.5 V
VO
M1
EN†
RL = 100 Ω
Switch ON
M2
EN†
† EN is the internal enable signal applied to the switch.
NOTE A: ron (M1) and ron (M2) are calculated from the voltage drop and current across the two terminals of M1 and M2, respectively.
Figure 11. Test Circuit for VO and ron
VCC = 6.2 V
0.1 µF
Oscilloscope
S
VO+
16
IA0
2
15
IA1
3
14
ID0
4
13
ID1
YA
100 Ω
100 Ω
VO−
VCC
1
TS5L100
Z
YD
IB0
5
12
IB1
6
11
IC0
7
10
IC1
8
9
YB
GND
VI+
100 Ω
100 Ω
YC
Pulse
Generator
VI−
Figure 12. Differential Crosstalk Measurement
Differential crosstalk is a measure of coupling noise between a transmit and receive pair in the LAN application.
Differential crosstalk depends on the edge rate, frequency, and load. This is calculated from the equation, XTALK(Diff)
db = 20 log VO(Diff)/VI(Diff), where VO(Diff) is the differential output voltage and VI(Diff) is the differential input voltage.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
PACKAGE OPTION ADDENDUM
www.ti.com
30-Aug-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TS5L100D
ACTIVE
SOIC
D
16
TS5L100DBQR
ACTIVE
SSOP/
QSOP
DBQ
TS5L100DBQRE4
ACTIVE
SSOP/
QSOP
TS5L100DE4
ACTIVE
TS5L100DR
40
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1YEAR
DBQ
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1YEAR
SOIC
D
16
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100DRE4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100PW
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100PWE4
ACTIVE
TSSOP
PW
20
70
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100PWR
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100PWRE4
ACTIVE
TSSOP
PW
20
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TS5L100RGYR
ACTIVE
QFN
RGY
16
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1YEAR
TS5L100RGYRG4
ACTIVE
QFN
RGY
16
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1YEAR
40
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated