DS1330W PRELIMINARY DS1330W 3.3V 256K Nonvolatile SRAM with Battery Monitor FEATURES PIN ASSIGNMENT • 10 years minimum data retention in the absence of external power • Data is automatically protected during power loss • Power supply monitor resets processor when VCC power loss occurs and holds processor in reset during VCC ramp–up • Battery monitor checks remaining capacity daily • Read and write access times as fast as 150 ns • Unlimited write cycle endurance • Typical standby current 50 µA BW NC NC RST VCC WE OE CE DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 GND • Upgrade for 32K x 8 SRAM, EEPROM or Flash • Lithium battery is electrically disconnected to retain freshness until power is applied for the first time • Optional industrial temperature range of –40°C to +85°C, designated IND • New PowerCap Module (PCM) package – Directly surface–mountable module – Replaceable snap–on PowerCap provides lithium backup battery – Standardized pinout for all nonvolatile SRAM products – Detachment feature on PowerCap allows easy removal using a regular screwdriver 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 GND VBAT 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 NC NC A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 34–PIN POWERCAP MODULE (PCM) (USES DS9034PC POWERCAP) PIN DESCRIPTION A0–A14 DQ0–DQ7 CE WE OE RST BW VCC GND NC – – – – – – – – – – Address Inputs Data In/Data Out Chip Enable Write Enable Output Enable Reset Output Battery Warning Output Power (+3.3 Volts) Ground No Connect DESCRIPTION The DS1330W 3.3V 256K Nonvolatile SRAM is a 262,144–bit, fully static, nonvolatile SRAM organized as 32,768 words by eight bits. Each NV SRAM has a self–contained lithium energy source and control circuitry which constantly monitors VCC for an out–of–tolerance condition. When such a condition occurs, the lithium energy source is automatically switched on and write protection is unconditionally enabled to prevent data corruption. Additionally, the DS1330W has dedicated circuitry for monitoring the status of VCC and the status of the internal lithium battery. DS1330W devices in the PowerCap Module package are directly surface mountable and are normally paired with a DS9034PC PowerCap to form a complete Nonvolatile SRAM module. The devices can be used in place of 32K x 8 SRAM, EEPROM or Flash components. 022598 1/11 DS1330W READ MODE The DS1330W executes a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip Enable) and OE (Output Enable) are active (low). The unique address specified by the 15 address inputs (A0 – A14) defines which of the 32,768 bytes of data is to be accessed. Valid data will be available to the eight data output drivers within tACC (Access Time) after the last address input signal is stable, providing that CE and OE (Output Enable) access times are also satisfied. If OE and CE access times are not satisfied, then data access must be measured from the later occurring signal (CE or OE) and the limiting parameter is either tCO for CE or tOE for OE rather than address access. WRITE MODE The DS1330W excutes a write cycle whenever the WE and CE signals are in the active (low) state after address inputs are stable. The later occurring falling edge of CE or WE will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of CE or WE. All address inputs must be kept valid throughout the write cycle. WE must return to the high state for a minimum recovery time (tWR) before another cycle can be initiated. The OE control signal should be kept inactive (high) during write cycles to avoid bus contention. However, if the output drivers are enabled (CE and OE active) then WE will disable the outputs in tODW from its falling edge. DATA RETENTION MODE The DS1330W provides full functional capability for VCC greater than 3.0 volts and write protects by 2.8 volts. Data is maintained in the absence of VCC without any additional support circuitry. The nonvolatile static RAMs constantly monitor VCC. Should the supply voltage decay, the NV SRAMs automatically write protect themselves, all inputs become “don’t care,” and all outputs become high impedance. As VCC falls below approximately 2.5 volts, the power switching circuit connects the lithium energy source to RAM to retain data. During power–up, when VCC rises above approximately 2.5 volts, the power switching circuit connects external VCC to the RAM and disconnects the lithium energy source. Normal RAM operation can resume after VCC exceeds 3.0 volts. SYSTEM POWER MONITORING The DS1330W has the ability to monitor the external VCC power supply. When an out–of–tolerance power 022598 2/11 supply condition is detected, the NV SRAM warns a processor–based system of impending power failure by asserting RST. On power up, RST is held active for 200 ms nominal to prevent system operation during power–on transients and to allow tREC to elapse. RST has an open–drain output driver. BATTERY MONITORING The DS1330W automatically performs periodic battery voltage monitoring on a 24 hour time interval. Such monitoring begins within tREC after VCC rises above VTP and is suspended when power failure occurs. After each 24 hour period has elapsed, the battery is connected to an internal 1 MΩ test resistor for one second. During this one second, if battery voltage falls below the battery voltage trip point (2.6V), the battery warning output BW is asserted. Once asserted, BW remains active until the module is replaced. The battery is still retested after each VCC power–up, however, even if BW is active. If the battery voltage is found to be higher than 2.6V during such testing, BW is de–asserted and regular 24–hour testing resumes. BW has an open– drain output driver. FRESHNESS SEAL Each DS1330W is shipped from Dallas Semiconductor with its lithium energy source disconnected, guaranteeing full energy capacity. When VCC is first applied at a level greater than VTP, the lithium energy source is enabled for battery backup operation. PACKAGES The 34–pin PowerCap Module integrates SRAM memory and nonvolatile control into a module base along with contacts for connection to the lithium battery in the DS9034PC PowerCap. The PowerCap Module package design allows a DS1330W device to be surface mounted without subjecting its lithium backup battery to destructive high–temperature reflow soldering. After a DS1330W module base is reflow soldered, a DS9034PC is snapped on top of the base to form a complete Nonvolatile SRAM module. The DS9034PC is keyed to prevent improper attachment. DS1330W module bases and DS9034PC PowerCaps are ordered separately and shipped in separate containers. See the DS9034PC data sheet for further information. DS1330W ABSOLUTE MAXIMUM RATINGS* Voltage On Any Pin Relative To Ground Operating Temperature Storage Temperature Soldering Temperature –0.3V to +4.6V 0°C to 70°C, –40°C to +85°C for IND parts –40°C to +70°C, –40°C to +85°C for IND parts 260°C For 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER (tA: See Note 10) SYMBOL MIN TYP MAX UNITS Power Supply Voltage VCC 3.0 3.3 3.6 V Logic 1 VIH 2.2 VCC V Logic 0 VIL 0.0 0.4 V (tA: See Note 10) (VCC=3.3V ±0.3V) DC ELECTRICAL CHARACTERISTICS PARAMETER NOTES SYMBOL MIN Input Leakage Current IIL I/O Leakage Current CE ≥ VIH ≤ VCC TYP MAX UNITS –1.0 +1.0 µA IIO –1.0 +1.0 µA Output Current @ 2.2V IOH –1.0 mA 14 Output Current @ 0.4V IOL 2.0 mA 14 Standby Current CE = 2.2V ICCS1 50 250 µA Standby Current CE = VCC–0.2V ICCS2 30 150 µA Operating Current ICCO1 50 mA Write Protection Voltage VTP 2.8 2.9 3.0 V SYMBOL MIN TYP MAX UNITS (tA = 25°C) CAPACITANCE PARAMETER NOTES Input Capacitance CIN 5 10 pF Input/Output Capacitance CI/O 5 10 pF NOTES 022598 3/11 DS1330W (tA: See Note 10) (VCC=3.3V ±0.3V) AC ELECTRICAL CHARACTERISTICS DS1330W–150 SYMBOL MIN Read Cycle Time tRC 150 Access Time tACC 150 ns OE to Output Valid tOE 70 ns CE to Output Valid tCO 150 ns OE or CE to Output Active tCOE Output High Z from Deselection tOD Output Hold from Address Change tOH 5 ns Write Cycle Time tWC 150 ns Write Pulse Width tWP 100 ns Address Setup Time tAW 0 ns Write Recovery Time tWR1 tWR2 5 20 ns 12 13 Output High Z from WE tODW ns 5 Output Active from WE tOEW 5 ns 5 Data Setup Time tDS 60 ns 4 Data Hold Time tDH1 tDH2 0 20 ns 12 13 PARAMETER MAX TYPE UNITS ns 5 35 35 READ CYCLE tRC ADDRESSES VIH VIL VIH VIL VIH VIL tOH tACC VIH CE tOD VIH OE tOE tCOE SEE NOTE 1 022598 4/11 VIH VIL tCOE DOUT VIH tCO VIL NOTES tOD VOH OUTPUT VOH VOL DATA VALID VOL ns 5 ns 5 3 DS1330W WRITE CYCLE 1 tWC VIH VIL VIH VIL ADDRESSES VIH VIL tAW CE VIL VIL tWP tWR1 WE VIH VIL VIL VIH tOEW tODW HIGH IMPEDANCE DOUT tDS tDH1 VIH VIH DIN DATA IN STABLE VIL VIL SEE NOTES 2, 3, 4, 6, 7, 8 AND 12 WRITE CYCLE 2 tWC ADDRESSES VIH VIL VIH VIL tWP tAW CE VIH VIL VIH VIL tWR2 VIL VIL VIL VIL VIH VIH WE tCOE tODW DOUT tDS tDH2 VIH VIH DATA IN STABLE DIN VIL VIL SEE NOTES 2, 3, 4, 6, 7, 8 AND 13 022598 5/11 DS1330W POWER–DOWN/POWER–UP CONDITION VCC VTP tDR 2.7V tR tF tREC tPD SLEWS WITH VCC tPU CE, WE VIH BACKUP CURRENTSUPPLIED FROM LITHIUM BATTERY tRPD RST tRPU VIL VIH tBPU SLEWS WITH VCC BW SEE NOTES 11 AND 14 BATTERY WARNING DETECTION V TP V CC t BPU V BAT 2.6V t t BTC BTPW BATTERY TEST ACTIVE t BW SEE NOTE 14 022598 6/11 BW V IL VIL DS1330W POWER–DOWN/POWER–UP TIMING PARAMETER VCC Fail Detect to CE and WE Inactive VCC slew from VTP to 0V VCC Fail Detect to RST Active SYMBOL (tA: See Note 10) MIN TYP tPD tF MAX UNITS NOTES 1.5 µs 11 µs 150 tRPD 15 µs 14 µs VCC slew from 0V to VTP tR 150 VCC Valid to CE and WE Inactive tPU 2 ms VCC Valid to End of Write Protection tREC 125 ms VCC Valid to RST Inactive tRPU 350 ms 14 VCC Valid to BW Valid tBPU 1 s 14 MAX UNITS 150 200 BATTERY WARNING TIMING PARAMETER Battery Test Cycle (tA: See Note 10) SYMBOL MIN tBTC TYP 24 NOTES hr Battery Test Pulse Width tBTPW 1 s Battery Test to BW Active tBW 1 s (tA = 25°C) PARAMETER Expected Data Retention Time SYMBOL MIN tDR 10 TYP MAX UNITS NOTES years 9 WARNING: Under no circumstance are negative undershoots, of any amplitude, allowed when device is in battery backup mode. NOTES: 1. WE is high for a Read Cycle. 2. OE = VIH or VIL. If OE = VIH during write cycle, the output buffers remain in a high impedance state. 3. tWP is specified as the logical AND of CE and WE. tWP is measured from the latter of CE or WE going low to the earlier of CE or WE going high. 4. tDS is measured from the earlier of CE or WE going high. 5. These parameters are sampled with a 5 pF load and are not 100% tested. 6. If the CE low transition occurs simultaneously with or latter than the WE low transition, the output buffers remain in a high impedance state during this period. 7. If the CE high transition occurs prior to or simultaneously with the WE high transition, the output buffers remain in high impedance state during this period. 8. If WE is low or the WE low transition occurs prior to or simultaneously with the CE low transition, the output buffers remain in a high impedance state during this period. 022598 7/11 DS1330W 9. Each DS1330W has a built–in switch that disconnects the lithium source until VCC is first applied by the user. The expected tDR is defined as accumulative time in the absence of VCC starting from the time power is first applied by the user. 10. All AC and DC electrical characteristics are valid over the full operating temperature range. For commercial products, this range is 0°C to 70°C. For industrial products (IND), this range is –40°C to +85°C. 11. In a power down condition the voltage on any pin may not exceed the voltage on VCC. 12. tWR1 and tDH1 are measured from WE going high. 13. tWR2 and tDH2 are measured from CE going high. 14. RST and BW are open–drain outputs and cannot source current. External pull–up resistors should be connected to these pins for proper operation. Both pins will sink 10 mA. DC TEST CONDITIONS AC TEST CONDITIONS Outputs Open Cycle = 200 ns for operating current All voltages are referenced to ground Output Load: 100 pF + 1TTL Gate Input Pulse Levels: 0 – 3.0V Timing Measurement Reference Levels Input: 1.5V Output: 1.5V Input pulse Rise and Fall Times: 5 ns ORDERING INFORMATION DS1330 W P – SSS – III Operating Temperature Range blank: 0° to 70° IND: –40° to +85°C Access Speed 150: 150 ns Package Type blank: 28–pin 600 mil DIP P: 34–pin PowerCap Module 022598 8/11 DS1330W DS1330W NONVOLATILE SRAM, 34–PIN POWERCAP MODULE INCHES PKG DIM MIN NOM MAX A 0.920 0.925 0.930 B 0.980 0.985 0.990 C – – 0.080 D 0.052 0.055 0.058 E 0.048 0.050 0.052 F 0.015 0.020 0.025 G 0.020 0.025 0.030 TOP VIEW SIDE VIEW BOTTOM VIEW: REFERENCE ONLY COMPONENTS AND PLACEMENTS MAY DIFFER FROM THOSE SHOWN 022598 9/11 DS1330W DS1330W NONVOLATILE SRAM, 34–PIN POWERCAP MODULE WITH POWERCAP INCHES TOP VIEW SIDE VIEW PKG DIM MIN NOM MAX A 0.920 0.925 0.930 B 0.955 0.960 0.965 C 0.240 0.245 0.250 D 0.052 0.055 0.058 E 0.048 0.050 0.052 F 0.015 0.020 0.025 G 0.020 0.025 0.030 ASSEMBLY AND USE Reflow soldering Dallas Semiconductor recommends that PowerCap Module bases experience one pass through solder reflow oriented label–side up (live–bug). Hand soldering and touch–up Do not touch soldering iron to leads for more than 3 seconds. To solder, apply flux to the pad, heat the lead frame pad and apply solder. To remove part, apply flux, heat pad until solder reflows, and use a solder wick. LPM replacement in a socket To replace a Low Profile Module in a 68–pin PLCC socket, attach a DS9034PC PowerCap to a module base then insert the complete module into the socket one row of leads at a time, pushing only on the corners of the cap. Never apply force to the center of the device. To remove from a socket, use a PLCC extraction tool and ensure that it does not hit or damage any of the module IC components. Do not use any other tool for extraction. COMPONENTS AND PLACEMENTS MAY DIFFER FROM THOSE SHOWN BOTTOM VIEW: REFERENCE ONLY 022598 10/11 DS1330W RECOMMENDED POWERCAP MODULE LAND PATTERN A INCHES D C PKG DIM MIN NOM MAX A – 1.050 – B – 0.826 – C – 0.050 – D – 0.030 – E – 0.112 – 16 PL B E RECOMMENDED POWERCAP MODULE SOLDER STENCIL A INCHES D C PKG DIM MIN NOM MAX A – 1.050 – B – 0.890 – C – 0.050 – D – 0.030 – E – 0.080 – 16 PL B E 022598 11/11