TI TMS320C6202GJL250X

TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
D High-Performance Fixed-Point Digital
D
D
D
D
D
D
Signal Processors (DSPs) − TMS320C62x
− 5-, 4-, 3.33-ns Instruction Cycle Time
− 200-, 250-, 300-MHz Clock Rate
− Eight 32-Bit Instructions/Cycle
− 1600, 2000, 2400 MIPS
C6202 and C6203B GLS Ball Grid Array
(BGA) Packages are Pin-Compatible With
the C6204 GLW BGA Package†
C6202B and C6203B GNZ and GNY
Packages are Pin-Compatible
VelociTI Advanced Very-Long-InstructionWord (VLIW) C62x DSP Core
− Eight Highly Independent Functional
Units:
− Six ALUs (32-/40-Bit)
− Two 16-Bit Multipliers (32-Bit Result)
− Load-Store Architecture With 32 32-Bit
General-Purpose Registers
− Instruction Packing Reduces Code Size
− All Instructions Conditional
Instruction Set Features
− Byte-Addressable (8-, 16-, 32-Bit Data)
− 8-Bit Overflow Protection
− Saturation
− Bit-Field Extract, Set, Clear
− Bit-Counting
− Normalization
3M-Bit On-Chip SRAM
− 2M-Bit Internal Program/Cache
(64K 32-Bit Instructions)
− 1M-Bit Dual-Access Internal Data
(128K Bytes)
− Organized as Two 64K-Byte Blocks for
Improved Concurrency
32-Bit External Memory Interface (EMIF)
− Glueless Interface to Synchronous
Memories: SDRAM or SBSRAM
− Glueless Interface to Asynchronous
Memories: SRAM and EPROM
− 52M-Byte Addressable External Memory
Space
D Four-Channel Bootloading
D
D
D
D
D
D
D
D
D
D
D
Direct-Memory-Access (DMA) Controller
With an Auxiliary Channel
Flexible Phase-Locked-Loop (PLL) Clock
Generator
32-Bit Expansion Bus (XBus)
− Glueless/Low-Glue Interface to Popular
PCI Bridge Chips
− Glueless/Low-Glue Interface to Popular
Synchronous or Asynchronous
Microprocessor Buses
− Master/Slave Functionality
− Glueless Interface to Synchronous FIFOs
and Asynchronous Peripherals
Three Multichannel Buffered Serial Ports
(McBSPs)
− Direct Interface to T1/E1, MVIP, SCSA
Framers
− ST-Bus-Switching Compatible
− Up to 256 Channels Each
− AC97-Compatible
− Serial-Peripheral Interface (SPI)
Compatible (Motorola)
Two 32-Bit General-Purpose Timers
IEEE-1149.1 (JTAG‡)
Boundary-Scan-Compatible
352-Pin BGA Package (GJL) (C6202)
352-Pin BGA Package (GNZ) (C6202B)
384-Pin BGA Package (GLS) (C6202)
384-Pin BGA Package (GNY) (C6202B)
0.18-µm/5-Level Metal Process (C6202)
0.15-µm/5-Level Metal Process (C6202B)
− CMOS Technology
3.3-V I/Os, 1.8-V Internal (C6202)
3.3-V I/Os, 1.5-V Internal (C6202B)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TMS320C62x, VelociTI, and C62x are trademarks of Texas Instruments.
Motorola is a trademark of Motorola, Inc.
Other trademarks are the property of their respective owners.
† For more details, see the GLS BGA package bottom view.
‡ IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
Copyright  2004, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
1
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Table of Contents
GJL, GNZ, GLS, and GNY BGA packages . . . . . . . . . . . . 3
parameter measurement information . . . . . . . . . . . . . . .
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
signal transition levels . . . . . . . . . . . . . . . . . . . . . . . . . .
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
timing parameters and board routing analysis . . . . . .
C62x device compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . .
functional and CPU (DSP core) block diagram . . . . . . . . . 9
asynchronous memory timing . . . . . . . . . . . . . . . . . . . . .
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . 10
synchronous-burst memory timing . . . . . . . . . . . . . . . . .
memory map summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . . .
peripheral register descriptions . . . . . . . . . . . . . . . . . . . . . 13
DMA synchronization events . . . . . . . . . . . . . . . . . . . . . . . 18
HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
interrupt sources and interrupt selector . . . . . . . . . . . . . . 19
reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . 20
external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . .
signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
expansion bus synchronous FIFO timing . . . . . . . . . . . .
development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
expansion bus asynchronous peripheral timing . . . . . .
documentation support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
expansion bus synchronous host-port timing . . . . . . . .
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
power-down mode logic . . . . . . . . . . . . . . . . . . . . . . . . . . .
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . .
IEEE 1149.1 JTAG compatibility statement . . . . . . . . . . .
absolute maximum ratings over operating case
temperature ranges . . . . . . . . . . . . . . . . . . . . . . . . . .
recommended operating conditions . . . . . . . . . . . . . . . . .
electrical characteristics over recommended ranges
of supply voltage and operating case temperature
2
47
47
48
49
52
56
59
64
65
67
68
70
74
40
43
45
expansion bus asynchronous host-port timing . . . . . . . 80
46
46
DMAC, timer, power-down timing . . . . . . . . . . . . . . . . . . 96
46
POST OFFICE BOX 1443
XHOLD/XHOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . 82
multichannel buffered serial port timing . . . . . . . . . . . . . 84
JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
GJL, GNZ, GLS, and GNY BGA packages
GJL 352-PIN BALL GRID ARRAY (BGA) PACKAGE ( BOTTOM VIEW ) [C6202 only]
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23 25
12 14 16 18 20 22 24 26
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
3
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
GJL, GNZ, GLS, and GNY BGA packages (continued)
GNZ 352-PIN BALL GRID ARRAY (BGA) PACKAGE ( BOTTOM VIEW ) [C6202B only]
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23 25
12 14 16 18 20 22 24 26
GLS 384-PIN BGA PACKAGE ( BOTTOM VIEW ) [C6202 only]
AB
Y
V
T
P
M
K
H
F
D
B
AA
W
U
R
N
L
J
G
E
C
A
3
1
2
5
4
9
7
6
8
10
11 13 15 17 19 21
12 14 16 18 20 22
The C6202 and C6203B GLS BGA packages are pin-compatible with the C6204 GLW
package except that the inner row of balls (which are additional power and ground pins)
are removed for the C6204 GLW package.
These balls are NOT applicable for the C6204 devices 340-pin GLW BGA package.
4
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
GJL, GNZ, GLS, and GNY BGA packages (continued)
GNY 384-PIN BGA PACKAGE ( BOTTOM VIEW ) [C6202B only]
AB
Y
V
T
P
M
K
H
F
D
B
AA
W
U
R
N
L
J
G
E
C
A
3
1
2
5
4
9
7
6
8
10
11 13 15 17 19 21
12 14 16 18 20 22
description
The TMS320C6202 and TMS320C6202B devices are part of the TMS320C62x fixed-point DSP generation
in the TMS320C6000 DSP platform. The C62x DSP devices are based on the high-performance, advanced
VelociTI very-long-instruction-word (VLIW) architecture developed by Texas Instruments (TI), making these
DSPs an excellent choice for multichannel and multifunction applications.
The TMS320C62x DSP offers cost-effective solutions to high-performance DSP-programming challenges.
The TMS320C6202/02B has a performance capability of up to 2400 million instructions per second (MIPS) at
300 MHz. The C6202/02B DSP possesses the operational flexibility of high-speed controllers and the numerical
capability of array processors. These processors have 32 general-purpose registers of 32-bit word length and
eight highly independent functional units. The eight functional units provide six arithmetic logic units (ALUs) for
a high degree of parallelism and two 16-bit multipliers for a 32-bit result. The C6202/02B can produce two
multiply-accumulates (MACs) per cycle. This gives a total of 600 million MACs per second (MMACS) for the
C6202/02B device. The C6202/02B DSP also has application-specific hardware logic, on-chip memory, and
additional on-chip peripherals.
The C6202/02B devices program memory consists of two blocks, with a 128K-byte block configured as
memory-mapped program space, and the other 128K-byte block user-configurable as cache or
memory-mapped program space. Data memory for the C6202/02B consists of two 64K-byte blocks of RAM.
TMS320C6000 is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
5
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
description (continued)
The C6202/02B device has a powerful and diverse set of peripherals. The peripheral set includes three
multichannel buffered serial ports (McBSPs), two general-purpose timers, a 32-bit expansion bus (XBus) that
offers ease of interface to synchronous or asynchronous industry-standard host bus protocols, and a glueless
32-bit external memory interface (EMIF) capable of interfacing to SDRAM or SBSRAM and asynchronous
peripherals.
The C62x devices have a complete set of development tools which includes: a new C compiler, an assembly
optimizer to simplify programming and scheduling, and a Windows debugger interface for visibility into source
code execution.
device characteristics
Table 1 provides an overview of the TMS320C6202, TMS320C6202B, TMS320C6203B, and the
TMS320C6204 pin-compatible DSPs. The table shows significant features of each device, including the
capacity of on-chip RAM, the peripherals, the execution time, and the package type with pin count, etc. This
data sheet primarily focuses on the functionality of the TMS320C6202/02B devices although it also identifies
to the user the pin-compatibility of the C6202 and C6203B GLS, and the C6204 GLW BGA packages. This data
sheet also identifies the pin-compatibility of the C6202B and the C6203B GNZ and GNY packages. For the
functionality information on the TMS320C6203B device, see the TMS320C6203B Fixed-Point Digital Signal
Processor data sheet (literature number SPRS086). For the functionality information on the TMS320C6204
device, see the TMS320C6204 Fixed-Point Digital Signal Processor data sheet (literature number SPRS152).
And for more details on the C6000 DSP device part numbers and part numbering, see Table 16 and Figure 4.
C6000 is a trademark of Texas Instruments.
Windows is a registered trademark of the Microsoft Corporation.
6
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
device characteristics (continued)
Table 1. Characteristics of the Pin-Compatible DSPs
HARDWARE FEATURES
C6202
C6202B
C6203B
C6204
EMIF
√
√
√
√
DMA
4-Channel
4-Channel With
Throughput
Enhancements
4-Channel With
Throughput
Enhancements
4-Channel With
Throughput
Enhancements
Expansion Bus
√
√
√
√
McBSPs
3
3
3
2
32-Bit Timers
2
2
2
2
Size (Bytes)
256K
256K
384K
64K
Organization
Block 0:
128K-Byte Mapped
Program
Block 1:
128K-Byte
Cache/Mapped
Program
Block 0:
128K-Byte Mapped
Program
Block 1:
128K-Byte
Cache/Mapped
Program
Block 0:
256K-Byte Mapped
Program
Block 1:
128K-Byte
Cache/Mapped
Program
1 Block:
64K-Byte
Cache/Mapped
Program
Peripherals
Internal
Program
Memory
Size (Bytes)
128K
128K
512K
64K
Internal Data
Memory
Organization
2 Blocks:
Four 16-Bit Banks
per Block
50/50 Split
2 Blocks:
Four 16-Bit Banks
per Block
50/50 Split
2 Blocks:
Four 16-Bit Banks
per Block
50/50 Split
2 Blocks:
Four 16-Bit Banks
per Block
50/50 Split
CPU ID +
CPU Rev ID
Control Status
Register (CSR.[31:16])
0x0002
0x0003
0x0003
0x0003
Frequency
MHz
200, 250
250, 300
250, 300
200
Cycle Time
ns
4 ns (6202-250)
5 ns (6202-200)
3.33 ns (6202B-300)
4 ns (6202B-250)
4 ns (02BGNZA-250)
3.33 ns (6203B-300)
4 ns (6203B-250)
4 ns (03BGNZA-250)
5 ns (6204-200)
Core (V)
18
1.8
15
1.5
I/O (V)
3.3
Voltage
PLL Options
BGA
Packages
†
CLKIN frequency
multiplier [Bypass (x1),
x4, x6, x7, x8, x9, x10,
and x11]
x1, x4
(Both Pkgs)
1.5
1.7
3.3
3.3
All PLL Options
(GNY Pkg)
All PLL Options
(GLS/GNY Pkgs)
x1, x4, x8, x10
(GNZ Pkg)
x1, x4, x8, x10
(GNZ Pkg)
15
1.5
3.3
x1, x4
(Both Pkgs)
27 x 27 mm
352-pin GJL
352-pin GNZ
352-pin GNZ
−
18 x 18 mm
384-pin GLS
−
384-pin GLS
340-pin GLW
18 x 18 mm
−
384-pin GNY
384-pin GNY
(2.x, 3.x only)
−
16 x 16 mm
−
−
−
288-pin GHK
0.18 µm
0.15 µm
0.15 µm
0.15 µm
PD
PD
PD
PD
Process
Technology
µm
Product
Status†
Product Preview (PP)
Advance Information
(AI)
Production Data (PD)
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include testing of all parameters.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
7
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
C62x device compatibility
The TMS320C6202, C6202B, C6203B, and C6204 devices are pin-compatible; thus, making new system
designs easier and providing faster time to market. The following list summarizes the C62x DSP device
characteristic differences:
D Core Supply Voltage (1.8 V versus 1.7 V versus 1.5 V)
The C6202 device core supply voltage is 1.8 V while the C6202B, C6203B, C6204 devices have core supply
voltages of 1.5 V. Furthermore, the C6203B-300 speed devices (GNY and GNZ packages) also have a
1.7-V core supply voltage.
D Device Clock Speeds
The C6202B and C6203B devices run at −250 and −300 MHz clock speeds (with a C620xBGNZA extended
temperature device that also runs at −250 MHz), while the C6202 device runs at −200 and −250 MHz, and
the C6204 device runs at −200 MHz clock speed.
D PLL Options Availability
Table 1 identifies the available PLL multiply factors [e.g., CLKIN x1 (PLL bypassed), x4, etc.] for each of the
C62x DSP devices. For additional details on the PLL clock module and specific options for the C6202/02B
devices, see the Clock PLL section of this data sheet.
For additional details on the PLL clock module and specific options for the C6203B device, see the Clock
PLL section of the TMS320C6203B Fixed-Point Digital Signal Processor Data Sheet (literature number
SPRS086).
And for additional details on the PLL clock module and specific options for the C6204 device, see the Clock
PLL section of the TMS320C6204 Fixed-Point Digital Signal Processor Data Sheet (literature number
SPRS152).
D On-Chip Memory Size
The C6202/02B, C6203B, and C6204 devices have different on-chip program memory and data memory
sizes (see Table 1).
D McBSPs
The C6202, C6202B, and C6203B devices have three McBSPs while the C6204 device has two McBSPs
on-chip.
For a more detailed discussion on migration concerns, and similarities/differences between the C6202,
C6202B, C6203B, and C6204 devices, see the How to Begin Development Today and Migrate Across the
TMS320C6202/02B/03B/04 DSPs Application Report (literature number SPRA603).
8
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
functional and CPU (DSP core) block diagram
C6202/02B Digital Signal Processors
SDRAM or
SBSRAM
SRAM
Program
Access/Cache
Controller
32
External Memory
Interface (EMIF)
ROM/FLASH
Internal Program Memory
(See Table 1)
I/O Devices
C62x CPU (DSP Core)
Timer 0
Instruction Fetch
Timer 1
Instruction Dispatch
Data Path A
Multichannel
Buffered Serial
Port 1
.L1
Multichannel
Buffered Serial
Port 2
I/O Devices
HOST CONNECTION
Master /Slave
TI PCI2040
Power PC
683xx
960
†
.S1
.M1 .D1
DMA
Bus
32
Peripheral Control Bus
Expansion
Bus (XBus)
32-Bit
Data Path B
A Register File
Interrupt
Selector
Synchronous
FIFOs
Control
Logic
Instruction Decode
Multichannel
Buffered Serial
Port 0
Framing Chips:
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
SPI Devices,
Codecs
Control
Registers
Direct Memory
Access Controller
(DMA)
(See Table 1)
PLL
(x1, x4, x6, x7, x8,
x9, x10, x11)†
PowerDown
Logic
Test
B Register File
.D2 .M2
.S2
In-Circuit
Emulation
.L2
Interrupt
Control
Internal Data
Memory
(See Table 1)
Data
Access
Controller
Boot Configuration
For additional details on the PLL clock module and specific options for the C6202/02B devices, see Table 1 and the Clock PLL section of this
data sheet.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
9
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
CPU (DSP core) description
The CPU fetches VelociTI advanced very-long instruction words (VLIW) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI VLIW architecture features
controls by which all eight units do not have to be supplied with instructions if they are not ready to execute. The
first bit of every 32-bit instruction determines if the next instruction belongs to the same execute packet as the
previous instruction, or whether it should be executed in the following clock as a part of the next execute packet.
Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The variable-length
execute packets are a key memory-saving feature, distinguishing the C62x CPU from other VLIW architectures.
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 16 32-bit registers for a total of 32 general-purpose registers. The two sets of functional units, along
with two register files, compose sides A and B of the CPU [see the functional and CPU (DSP core) block diagram
and Figure 1]. The four functional units on each side of the CPU can freely share the 16 registers belonging to
that side. Additionally, each side features a single data bus connected to all the registers on the other side, by
which the two sets of functional units can access data from the register files on the opposite side. While register
access by functional units on the same side of the CPU as the register file can service all the units in a single
clock cycle, register access using the register file across the CPU supports one read and one write per cycle.
Another key feature of the C62x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C62x CPU supports a variety of indirect addressing modes using either linear- or circular-addressing modes
with 5- or 15-bit offsets. All instructions are conditional, and most can access any one of the 32 registers. Some
registers, however, are singled out to support specific addressing or to hold the condition for conditional
instructions (if the condition is not automatically “true”). The two .M functional units are dedicated for multiplies.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. If an execute packet crosses the
256-bit-wide fetch-packet boundary, the assembler places it in the next fetch packet, while the remainder of the
current fetch packet is padded with NOP instructions. The number of execute packets within a fetch packet can
vary from one to eight. Execute packets are dispatched to their respective functional units at the rate of one per
clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from the current fetch
packet have been dispatched. After decoding, the instructions simultaneously drive all active functional units
for a maximum execution rate of eight instructions every clock cycle. While most results are stored in 32-bit
registers, they can be subsequently moved to memory as bytes or half-words as well. All load and store
instructions are byte-, half-word, or word-addressable.
10
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
CPU (DSP core) description (continued)
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á
Á ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
Á
Á ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Á ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Á
Á
src1
.L1
src2
dst
long dst
long src
ST1
Data Path A
long src
long dst
dst
.S1
src1
8
.M1
dst
src1
LD1
DA1
DA2
.D2
dst
src1
src2
1X
src2
src1
dst
Á
Á
Á
Á
src2
src1
dst
src2
Data Path B
src1
dst
long dst
long src
.S2
ST2
long src
long dst
dst
.L2
src2
src1
Register
File A
(A0−A15)
2X
LD2
.M2
32
Á
Á
Á
Á
src2
.D1
8
8
src2
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁ
Register
File B
(B0−B15)
8
32
8
Á
Á
Á
Á
8
Control
Register
File
Figure 1. TMS320C62x CPU (DSP Core) Data Paths
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
11
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
memory map summary
Table 2 shows the memory map address ranges of the C6202/02B device. The C6202/02B device has the
capability of a MAP 0 or MAP 1 memory block configuration. These memory block configurations are set up at
reset by the boot configuration pins (generically called BOOTMODE[4:0]). For the C6202/02B device, the
BOOTMODE configuration is handled, at reset, by the expansion bus module (specifically XD[4:0] pins). For
more detailed information on the C6202/02B device settings, which include the device boot mode configuration
at reset and other device-specific configurations, see TMS320C620x/C670x DSP Boot Modes and
Configuration (literature number SPRU642).
Table 2. TMS320C6202/02B Memory Map Summary
MEMORY BLOCK DESCRIPTION
12
MAP 0
MAP 1
BLOCK SIZE
(BYTES)
HEX ADDRESS RANGE
External Memory Interface (EMIF) CE0
Internal Program RAM
256K
0000_0000–0003_FFFF
EMIF CE0
Reserved
4M–256K
0004_0000–003F_FFFF
EMIF CE0
EMIF CE0
12M
0040_0000–00FF_FFFF
EMIF CE1
EMIF CE0
4M
0100_0000–013F_FFFF
Internal Program RAM
EMIF CE1
256K
0140_0000–0143_FFFF
Reserved
EMIF CE1
4M–256K
0144_0000–017F_FFFF
EMIF Registers
256K
0180_0000–0183_FFFF
DMA Controller Registers
256K
0184_0000–0187_FFFF
Expansion Bus (XBus) Registers
256K
0188_0000–018B_FFFF
McBSP 0 Registers
256K
018C_0000–018F_FFFF
McBSP 1 Registers
256K
0190_0000–0193_FFFF
Timer 0 Registers
256K
0194_0000–0197_FFFF
Timer 1 Registers
256K
0198_0000–019B_FFFF
Interrupt Selector Registers
512
019C_0000–019C_01FF
Power-Down Registers
256K–512
019C_0200–019F_FFFF
Reserved
256K
01A0_0000–01A3_FFFF
McBSP 2 Registers
256K
01A4_0000–01A7_FFFF
Reserved
5.5M
01A8_0000–01FF_FFFF
EMIF CE2
16M
0200_0000–02FF_FFFF
EMIF CE3
16M
0300_0000–03FF_FFFF
Reserved
1G–64M
0400_0000–3FFF_FFFF
XBus XCE0
256M
4000_0000–4FFF_FFFF
XBus XCE1
256M
5000_0000–5FFF_FFFF
XBus XCE2
256M
6000_0000–6FFF_FFFF
7000_0000–7FFF_FFFF
XBus XCE3
256M
Internal Data RAM
128K
8000_0000–8001_FFFF
Reserved
2G–128K
8002_0000–FFFF_FFFF
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral register descriptions
Table 3 through Table 13 identify the peripheral registers for the C6202/02B device by their register names,
acronyms, and hex address or hex address range. For more detailed information on the register contents, bit
names, and their descriptions, see the peripheral reference guide referenced in TMS320C6000 DSP
Peripherals Overview Reference Guide (literature number SPRU190).
Table 3. EMIF Registers
HEX ADDRESS RANGE
ACRONYM
0180 0000
GBLCTL
EMIF global control
REGISTER NAME
COMMENTS
0180 0004
CECTL1
EMIF CE1 space control
External or internal; dependent on MAP0 or
MAP1 configuration (selected by the MAP bit
in the EMIF GBLCTL register)
0180 0008
CECTL0
EMIF CE0 space control
External or internal; dependent on MAP0 or
MAP1 configuration (selected by the MAP bit
in the EMIF GBLCTL register)
0180 000C
−
0180 0010
CECTL2
EMIF CE2 space control
Corresponds to EMIF CE2 memory space:
[0200 0000−02FF FFFF]
0180 0014
CECTL3
EMIF CE3 space control
Correspond to EMIF CE3 memory space:
[0300 0000−03FF FFFF]
Reserved
0180 0018
SDCTL
EMIF SDRAM control
0180 001C
SDTIM
EMIF SDRAM refresh control
0180 0020 − 0180 0054
—
Reserved
0180 0058 − 0183 FFFF
—
Reserved
Table 4. DMA Registers
HEX ADDRESS RANGE
ACRONYM
0184 0000
PRICTL0
DMA channel 0 primary control
REGISTER NAME
0184 0004
PRICTL2
DMA channel 2 primary control
0184 0008
SECCTL0
DMA channel 0 secondary control
0184 000C
SECCTL2
DMA channel 2 secondary control
0184 0010
SRC0
DMA channel 0 source address
0184 0014
SRC2
DMA channel 2 source address
0184 0018
DST0
DMA channel 0 destination address
0184 001C
DST2
DMA channel 2 destination address
0184 0020
XFRCNT0
DMA channel 0 transfer counter
0184 0024
XFRCNT2
DMA channel 2 transfer counter
0184 0028
GBLCNTA
DMA global count reload register A
0184 002C
GBLCNTB
DMA global count reload register B
0184 0030
GBLIDXA
DMA global index register A
0184 0034
GBLIDXB
DMA global index register B
0184 0038
GBLADDRA
DMA global address register A
0184 003C
GBLADDRB
DMA global address register B
0184 0040
PRICTL1
DMA channel 1 primary control
0184 0044
PRICTL3
DMA channel 3 primary control
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
13
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 4. DMA Registers (Continued)
HEX ADDRESS RANGE
ACRONYM
0184 0048
SECCTL1
DMA channel 1 secondary control
REGISTER NAME
0184 004C
SECCTL3
DMA channel 3 secondary control
0184 0050
SRC1
DMA channel 1 source address
0184 0054
SRC3
DMA channel 3 source address
0184 0058
DST1
DMA channel 1 destination address
0184 005C
DST3
DMA channel 3 destination address
0184 0060
XFRCNT1
DMA channel 1 transfer counter
0184 0064
XFRCNT3
DMA channel 3 transfer counter
0184 0068
GBLADDRC
DMA global address register C
0184 006C
GBLADDRD
DMA global address register D
0184 0070
AUXCTL
DMA auxiliary control register
0184 0074−0187 FFFF
—
Reserved
Table 5. Expansion Bus (XBUS) Registers
14
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
0188 0000
XBGC
0188 0004
XCECTL1
XCE1 space control register
Corresponds to XBus XCE0 memory
space: [4000 0000−4FFF FFFF]
0188 0008
XCECTL0
XCE0 space control register
Corresponds to XBus XCE1 memory
space: [5000 0000−5FFF FFFF]
0188 000C
XBHC
Expansion bus host port interface control register
DSP read/write access only
0188 0010
XCECTL2
XCE2 space control register
Corresponds to XBus XCE2 memory
space: [6000 0000−6FFF FFFF]
0188 0014
XCECTL3
XCE3 space control register
Corresponds to XBus XCE3 memory
space: [7000 0000−7FFF FFFF]
Expansion bus global control register
0188 0018
—
Reserved
0188 001C
—
Reserved
0188 0020
XBIMA
Expansion bus internal master address register
DSP read/write access only
0188 0024
XBEA
Expansion bus external address register
DSP read/write access only
0188 0028 − 018B FFFF
—
—
XBISA
—
XBD
Reserved
Expansion bus internal slave address
Expansion bus data
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 6. Interrupt Selector Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
019C 0000
MUXH
Interrupt multiplexer high
Selects which interrupts drive CPU
interrupts 10−15 (INT10−INT15)
019C 0004
MUXL
Interrupt multiplexer low
Selects which interrupts drive CPU
interrupts 4−9 (INT04−INT09)
019C 0008
EXTPOL
External interrupt polarity
Sets the polarity of the external
interrupts (EXT_INT4−EXT_INT7)
019C 000C−019C 01FF
—
019C 0200
PDCTL
019C 0204−019F FFFF
—
Reserved
Peripheral power-down control register
Reserved
Table 7. Peripheral Power-Down Control Register
HEX ADDRESS RANGE
ACRONYM
019C 0200
PDCTL
REGISTER NAME
Peripheral power-down control register
Table 8. McBSP 0 Registers
HEX ADDRESS RANGE
018C 0000
ACRONYM
REGISTER NAME
DRR0
McBSP0 data receive register
018C 0004
DXR0
McBSP0 data transmit register
018C 0008
SPCR0
018C 000C
RCR0
McBSP0 receive control register
018C 0010
XCR0
McBSP0 transmit control register
018C 0014
SRGR0
018C 0018
MCR0
McBSP0 multichannel control register
018C 001C
RCER0
McBSP0 receive channel enable register
018C 0020
XCER0
McBSP0 transmit channel enable register
018C 0024
PCR0
018C 0028−018F FFFF
—
COMMENTS
The CPU and DMA controller can only read
this register; they cannot write to it.
McBSP0 serial port control register
McBSP0 sample rate generator register
McBSP0 pin control register
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
15
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 9. McBSP 1 Registers
HEX ADDRESS RANGE
0190 0000
ACRONYM
REGISTER NAME
DRR1
Data receive register
0190 0004
DXR1
McBSP1 data transmit register
0190 0008
SPCR1
0190 000C
RCR1
McBSP1 receive control register
0190 0010
XCR1
McBSP1 transmit control register
0190 0014
SRGR1
0190 0018
MCR1
McBSP1 multichannel control register
0190 001C
RCER1
McBSP1 receive channel enable register
0190 0020
XCER1
McBSP1 transmit channel enable register
0190 0024
PCR1
0190 0028−0193 FFFF
—
COMMENTS
The CPU and DMA controller can only read
this register; they cannot write to it.
McBSP1 serial port control register
McBSP1 sample rate generator register
McBSP1 pin control register
Reserved
Table 10. McBSP 1 Registers
16
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
0190 0000
DRR1
Data receive register
0190 0004
DXR1
McBSP1 data transmit register
0190 0008
SPCR1
0190 000C
RCR1
McBSP1 receive control register
0190 0010
XCR1
McBSP1 transmit control register
0190 0014
SRGR1
McBSP1 serial port control register
McBSP1 sample rate generator register
0190 0018
MCR1
McBSP1 multichannel control register
0190 001C
RCER1
McBSP1 receive channel enable register
0190 0020
XCER1
McBSP1 transmit channel enable register
0190 0024
PCR1
0190 0028−0193 FFFF
—
McBSP1 pin control register
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
The CPU and DMA controller can only read
this register; they cannot write to it.
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 11. McBSP 2 Registers
HEX ADDRESS RANGE
01A4 0000
ACRONYM
REGISTER NAME
DRR2
McBSP2 data receive register
01A4 0004
DXR2
McBSP2 data transmit register
01A4 0008
SPCR2
01A4 000C
RCR2
McBSP2 receive control register
01A4 0010
XCR2
McBSP2 transmit control register
01A4 0014
SRGR2
01A4 0018
MCR2
McBSP2 multichannel control register
01A4 001C
RCER2
McBSP2 receive channel enable register
01A4 0020
XCER2
McBSP2 transmit channel enable register
01A4 0024
PCR2
01A4 0028−01A7 FFFF
—
COMMENTS
The CPU and DMA controller can only read
this register; they cannot write to it.
McBSP2 serial port control register
McBSP2 sample rate generator register
McBSP2 pin control register
Reserved
Table 12. Timer 0 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
0194 0000
CTL0
Timer 0 control register
Determines the operating mode of the timer,
monitors the timer status, and controls the
function of the TOUT pin.
0194 0004
PRD0
Timer 0 period register
Contains the number of timer input clock
cycles to count. This number controls the
TSTAT signal frequency.
0194 0008
CNT0
Timer 0 counter register
Contains the current
incrementing counter.
0194 000C−0197 FFFF
—
value
of
the
Reserved
Table 13. Timer 1 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
0198 0000
CTL1
Timer 1 control register
Determines the operating mode of the timer,
monitors the timer status, and controls the
function of the TOUT pin.
0198 0004
PRD1
Timer 1 period register
Contains the number of timer input clock
cycles to count. This number controls the
TSTAT signal frequency.
0198 0008
CNT1
Timer 1 counter register
Contains the current
incrementing counter.
0198 000C−019B FFFF
—
value
of
the
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
17
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
DMA synchronization events
The C6202/C6202B DMA supports up to four independent programmable DMA channels. The four main DMA
channels can be read/write synchronized based on the events shown in Table 14. Selection of these events is
done via the RSYNC and WSYNC fields in the Primary Control registers of the specific DMA channel. For more
detailed information on the DMA module, associated channels, and event-synchronization, see the
TMS320C620x/C670x DSP Program and Data Memory Controller / Direct Memory Access (DMA) Comtroller
Reference Guide (literature number SPRU577).
Table 14. TMS320C6202/02B DMA Synchronization Events
18
DMA EVENT
NUMBER
(BINARY)
EVENT NAME
00000
Reserved
00001
TINT0
Timer 0 interrupt
00010
TINT1
Timer 1 interrupt
EVENT DESCRIPTION
Reserved
00011
SD_INT
00100
EXT_INT4
External interrupt pin 4
00101
EXT_INT5
External interrupt pin 5
00110
EXT_INT6
External interrupt pin 6
00111
EXT_INT7
External interrupt pin 7
01000
DMA_INT0
DMA channel 0 interrupt
01001
DMA_INT1
DMA channel 1 interrupt
01010
DMA_INT2
DMA channel 2 interrupt
01011
DMA_INT3
DMA channel 3 interrupt
01100
XEVT0
McBSP0 transmit event
01101
REVT0
McBSP0 receive event
01110
XEVT1
McBSP1 transmit event
01111
REVT1
McBSP1 receive event
10000
DSP_INT
10001
XEVT2
McBSP2 transmit event
10010
REVT2
McBSP2 receive event
10011 −11111
Reserved
POST OFFICE BOX 1443
EMIF SDRAM timer interrupt
Host processor-to-DSP interrupt
Reserved. Not used.
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
interrupt sources and interrupt selector
The C62x DSP core supports 16 prioritized interrupts, which are listed in Table 15. The highest-priority interrupt
is INT_00 (dedicated to RESET) while the lowest-priority interrupt is INT_15. The first four interrupts
(INT_00−INT_03) are non-maskable and fixed. The remaining interrupts (INT_04−INT_15) are maskable and
default to the interrupt source specified in Table 15. The interrupt source for interrupts 4−15 can be programmed
by modifying the selector value (binary value) in the corresponding fields of the Interrupt Selector Control
registers: MUXH (address 0x019C0000) and MUXL (address 0x019C0004).
Table 15. C6202/02B DSP Interrupts
CPU
INTERRUPT
NUMBER
INTERRUPT
SELECTOR
CONTROL
REGISTER
SELECTOR
VALUE
(BINARY)
INTERRUPT
EVENT
INT_00†
—
—
RESET
INT_01†
—
—
NMI
INT_02†
—
—
Reserved
Reserved. Do not use.
INT_03†
—
—
Reserved
Reserved. Do not use.
INT_04‡
MUXL[4:0]
00100
EXT_INT4
External interrupt pin 4
INT_05‡
MUXL[9:5]
00101
EXT_INT5
External interrupt pin 5
INT_06‡
MUXL[14:10]
00110
EXT_INT6
External interrupt pin 6
INT_07‡
MUXL[20:16]
00111
EXT_INT7
External interrupt pin 7
INT_08‡
MUXL[25:21]
01000
DMA_INT0
DMA channel 0 interrupt
INT_09‡
MUXL[30:26]
01001
DMA_INT1
DMA channel 1 interrupt
INT_10‡
MUXH[4:0]
00011
SD_INT
INT_11‡
MUXH[9:5]
01010
DMA_INT2
DMA channel 2 interrupt
INT_12‡
MUXH[14:10]
01011
DMA_INT3
DMA channel 3 interrupt
INT_13‡
MUXH[20:16]
00000
DSP_INT
INT_14‡
MUXH[25:21]
00001
TINT0
Timer 0 interrupt
INT_15‡
MUXH[30:26]
00010
TINT1
Timer 1 interrupt
—
—
01100
XINT0
McBSP0 transmit interrupt
—
—
01101
RINT0
McBSP0 receive interrupt
—
—
01110
XINT1
McBSP1 transmit interrupt
—
—
01111
RINT1
McBSP1 receive interrupt
—
—
10000
Reserved
—
—
10001
XINT2
McBSP2 transmit interrupt
—
—
10010
RINT2
McBSP2 receive interrupt
—
—
10011 − 11111
Reserved
INTERRUPT SOURCE
EMIF SDRAM timer interrupt
Host-processor-to-DSP interrupt
Reserved. Not used.
Reserved. Do not use.
†
Interrupts INT_00 through INT_03 are non-maskable and fixed.
‡ Interrupts INT_04 through INT_15 are programmable by modifying the binary selector values in the Interrupt Selector Control
registers fields. Table 15 shows the default interrupt sources for Interrupts INT_04 through INT_15. For more detailed information
on interrupt sources and selection, see TMS320C6000 DSP Interrupt Selector Reference Guide (literature number SPRU646).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
19
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
signal groups description
CLKIN
CLKOUT2
CLKOUT1
CLKMODE0
CLKMODE1†
CLKMODE2†
PLLV
PLLG
PLLF
Clock/PLL
Reset and
Interrupts
TMS
TDO
TDI
TCK
TRST
EMU1
EMU0
IEEE Standard
1149.1
(JTAG)
Emulation
RSV4
RSV3
RSV2
RSV1
RSV0
Reserved
DMA Status
DMAC3
DMAC2
DMAC1
DMAC0
Power-Down
Status
PD
Control/Status
†
CLKMODE1 and CLKMODE2 are NOT available on the C6202 device GJL package.
CLKMODE2 is also NOT available on the GNZ package for the C6202B device.
Figure 2. CPU (DSP Core) Signals
20
POST OFFICE BOX 1443
RESET
NMI
EXT_INT7
EXT_INT6
EXT_INT5
EXT_INT4
IACK
INUM3
INUM2
INUM1
INUM0
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
signal groups description (continued)
ED[31:0]
32
CE3
CE2
CE1
CE0
EA[21:2]
BE3
BE2
BE1
BE0
TOUT1
TINP1
Asynchronous
Memory
Control
Data
Memory Map
Space Select
20
Synchronous
Memory
Control
Word Address
HOLD/
HOLDA
Byte Enables
ARE
AOE
AWE
ARDY
SDA10
SDRAS/SSOE
SDCAS/SSADS
SDWE/SSWE
HOLD
HOLDA
EMIF
(External Memory Interface)
Timer 1
Timer 0
TOUT0
TINP0
Timers
McBSP1
McBSP0
CLKX1
FSX1
DX1
Transmit
Transmit
CLKX0
FSX0
DX0
CLKR1
FSR1
DR1
Receive
Receive
CLKR0
FSR0
DR0
CLKS1
Clock
Clock
CLKS0
McBSP2
Transmit
CLKX2
FSX2
DX2
Receive
CLKR2
FSR2
DR2
Clock
CLKS2
McBSPs
(Multichannel Buffered Serial Ports)
Figure 3. Peripheral Signals
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
21
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
signal groups description (continued)
XD[31:0]
XBE3/XA5
XBE2/XA4
XBE1/XA3
XBE0/XA2
XRDY
32
Data
Byte-Enable
Control/
Address
Control
Clocks
I/O Port
Control
XHOLD
XHOLDA
XFCLK
XOE
XRE
XWE/XWAIT
XCE3
XCE2
XCE1
XCE0
Arbitration
Expansion Bus
Host
Interface
Control
Figure 3. Peripheral Signals (Continued)
22
XCLKIN
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
XCS
XAS
XCNTL
XW/R
XBLAST
XBOFF
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
CLOCK/PLL
CLKIN
C12
B10
I
Clock Input
CLKOUT1
AD20
Y18
O
Clock output at full device speed
CLKOUT2
AC19
AB19
O
CLKMODE0
B15
B12
I
CLKMODE1
C11‡
A9§
I
CLKMODE2
Clock output at half (1/2) of device speed
-
Used for synchronous memory interface
Clock mode selects
-
Selects what multiply factors of the input clock frequency the CPU frequency equals.
For more details on the GJL,
GJL GNZ,
GNZ GLS,
GLS and GNY CLKMODE pins and the PLL multiply
factors for the C6202 and C6202B devices, see the Clock PLL section of this data sheet.
−
A14§
I
PLLV¶
D13
C11
A#
PLL analog VCC connection for the low-pass filter
PLLG¶
D14
C12
A#
PLL analog GND connection for the low-pass filter
PLL low-pass filter connection to external components and a bypass capacitor
PLLF¶
C13
A11
A#
TMS
AD7
Y5
I
TDO
AE6
AA4
O/Z
TDI
AF5
Y4
I
JTAG test-port data in (features an internal pullup)
TCK
AE5
AB2
I
JTAG test-port clock
TRST
AC7
AA3
I
JTAG test-port reset (features an internal pulldown)
EMU1
AF6
AA5
I/O/Z
Emulation pin 1, pullup with a dedicated 20-kΩ resistor||
EMU0
AC8
AB4
I/O/Z
Emulation pin 0, pullup with a dedicated 20-kΩ resistor||
JTAG EMULATION
JTAG test-port mode select (features an internal pullup)
JTAG test-port data out
RESET AND INTERRUPTS
RESET
K2
J3
I
NMI
L2
K2
I
EXT_INT7
V4
U2
EXT_INT6
Y2
U3
EXT_INT5
AA1
W1
EXT_INT4
W4
V2
IACK
Y1
V1
INUM3
V2
R3
INUM2
U4
T1
INUM1
V3
T2
INUM0
W2
T3
Device reset
Nonmaskable interrupt
-
Edge-driven (rising edge)
External interrupts
I
O
-
Edge-driven
-
Polarity independently selected via the external interrupt polarity register bits
(EXTPOL.[3:0])
Interrupt acknowledge for all active interrupts serviced by the CPU
Active interrupt identification number
O
-
Valid during IACK for all active interrupts (not just external)
-
Encoding
the
E
di order
d follows
f ll
th interrupt-service
i t
t
i fetch-packet
f t h
k t ordering
d i
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
For the C6202 GJL package only, the C11 pin is ground (VSS). For all C62x GNZ packages, the C11 pin is CLKMODE1.
§ For the C6202 GLS package, the CLKMODE2 (A14) and CLKMODE1 (A9) pins are internally unconnected.
¶ PLLV, PLLG, and PLLF are not part of external voltage supply or ground. See the Clock PLL section for information on how to connect these
pins.
# A = Analog Signal (PLL Filter)
|| For emulation and normal operation, pull up EMU1 and EMU0 with a dedicated 20-kΩ resistor. For boundary scan, pull down EMU1 and EMU0
with a dedicated 20-kΩ resistor.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
23
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
POWER-DOWN STATUS
PD
AB2
Y2
O
Power-down modes 2 or 3 (active if high)
A9
C8
I
Expansion bus synchronous host interface clock input
O
Expansion bus FIFO interface clock output
EXPANSION BUS
XCLKIN
XFCLK
†
B9
A8
XD31
D15
C13
XD30
B16
A13
XD29
A17
C14
XD28
B17
B14
XD27
D16
B15
XD26
A18
C15
XD25
B18
A15
XD24
D17
B16
XD23
C18
C16
XD22
A20
A17
XD21
D18
B17
XD20
C19
C17
XD19
A21
B18
XD18
D19
A19
XD17
C20
C18
XD16
B21
B19
XD15
A22
C19
XD14
D20
B20
XD13
B22
A21
XD12
E25
C21
XD11
F24
D20
XD10
E26
B22
XD9
F25
D21
XD8
G24
E20
XD7
H23
E21
XD6
F26
D22
XD5
G25
F20
XD4
J23
F21
XD3
G26
E22
XD2
H25
G20
XD1
J24
G21
XD0
K23
G22
Expansion bus data
I/O/Z
-
Used for transfer of data, address, and control
-
Also controls initialization of DSP modes and expansion bus at reset
[Note: For more information on pin control and boot configuration fields, see the Boot
Modes and Configuration
g
chapter
p
of the TMS320C6000 DSP Peripherals
p
Overview
R f
Reference
Guide
G id (literature
(lit t
number
b SPRU190).]
SPRU190) ]
XD[30:16] − XCE[3:0] memory type
XD13 − XBLAST polarity
XD12 − XW/R polarity
l it
XD11 − Asynchronous or synchronous host operation
XD10 − Arbitration mode (internal or external)
XD9 − FIFO mode
XD8 − Little e
endian/big
dia /big endian
e dia
XD[4:0] − Boot mode
All other expansion bus data pins not listed should be pulled down.
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
24
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
EXPANSION BUS (CONTINUED)
XCE3
F2
D2
XCE2
E1
B1
XCE1
F3
D3
XCE0
E2
C2
XBE3/XA5
C7
C5
XBE2/XA4
D8
A4
XBE1/XA3
A6
B5
XBE0/XA2
C8
C6
XOE
A7
A6
O/Z
Expansion bus I/O port output-enable
XRE
C9
C7
O/Z
Expansion bus I/O port read-enable
XWE/XWAIT
D10
B7
O/Z
Expansion bus I/O port write-enable and host-port wait signals
XCS
A10
C9
I
XAS
D9
B6
I/O/Z
XCNTL
B10
B9
I
XW/R
D11
B8
I/O/Z
Expansion bus host-port write/read-enable. XW/R polarity is selected at reset.
XRDY
A5
C4
I/O/Z
Expansion bus host-port ready (active low) and I/O port ready (active high)
Expansion bus host-port burst last-polarity selected at reset
Expansion bus I/O port memory space enables
O/Z
-
Enabled by bits 28,
28 29
29, and 30 of the word address
-
Only
O l one asserted
t d during
d i any I/O portt data
d t access
Expansion bus multiplexed byte-enable control/address signals
I/O/Z
-
Act as byte-enable
byte enable for host
host-port
port operation
-
Act
for
A t as address
dd
f I/O portt operation
ti
Expansion bus host-port chip-select input
Expansion bus host-port address strobe
Expansion bus host control. XCNTL selects between expansion bus address or data register.
XBLAST
B6
B4
I/O/Z
XBOFF
B11
A10
I
XHOLD
B5
A2
I/O/Z
Expansion bus hold request
XHOLDA
D7
B3
I/O/Z
Expansion bus hold acknowledge
Expansion bus back off
EMIF − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY
CE3
AB25
Y21
CE2
AA24
W20
CE1
AB26
AA22
CE0
AA25
W21
BE3
Y24
V20
BE2
W23
V21
BE1
AA26
W22
Memory space enables
O/Z
-
Enabled by bits 24 and 25 of the word address
-
Only
O l one asserted
t d during
d i any external
t
l data
d t access
Byte-enable
y
control
O/Z
-
Decoded from the two lowest bits of the internal address
-
Byte-write
y
enables for most types
yp of memoryy
BE0
†
Y25
U20
- Can be directly connected to SDRAM read and write mask signal (SDQM)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
25
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
EMIF − ADDRESS
EA21
J25
H20
EA20
J26
H21
EA19
L23
H22
EA18
K25
J20
EA17
L24
J21
EA16
L25
K21
EA15
M23
K20
EA14
M24
K22
EA13
M25
L21
EA12
N23
L20
EA11
P24
L22
EA10
P23
M20
EA9
R25
M21
EA8
R24
N22
EA7
R23
N20
EA6
T25
N21
EA5
T24
P21
EA4
U25
P20
EA3
T23
R22
EA2
V26
R21
ED31
AD8
Y6
ED30
AC9
AA6
ED29
AF7
AB6
ED28
AD9
Y7
ED27
AC10
AA7
ED26
AE9
AB8
ED25
AF9
Y8
ED24
AC11
AA8
ED23
AE10
AA9
ED22
AD11
Y9
ED21
AE11
AB10
ED20
AC12
Y10
ED19
AD12
AA10
ED18
AE12
AA11
ED17
AC13
Y11
ED16
AD14
AB12
ED15
AC14
Y12
ED14
AE15
AA12
O/Z
External address (word address)
EMIF − DATA
†
I/O/Z
External data
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
26
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
EMIF − DATA (CONTINUED)
ED13
AD15
ED12
AC15
AA13
Y13
ED11
AE16
AB13
ED10
AD16
Y14
ED9
AE17
AA14
ED8
AC16
AA15
ED7
AF18
Y15
ED6
AE18
AB15
ED5
AC17
AA16
ED4
AD18
Y16
ED3
AF20
AB17
ED2
AC18
AA17
ED1
AD19
Y17
ED0
AF21
AA18
ARE
V24
T21
O/Z
Asynchronous memory read-enable
AOE
V25
R20
O/Z
Asynchronous memory output-enable
AWE
U23
T22
O/Z
Asynchronous memory write-enable
ARDY
W25
T20
I
Asynchronous memory ready input
I/O/Z
External data
EMIF − ASYNCHRONOUS MEMORY CONTROL
EMIF − SYNCHRONOUS DRAM (SDRAM)/SYNCHRONOUS BURST SRAM (SBSRAM) CONTROL
SDA10
AE21
AA19
O/Z
SDRAM address 10 (separate for deactivate command)
SDCAS/SSADS
AE22
AB21
O/Z
SDRAM column-address strobe/SBSRAM address strobe
SDRAS/SSOE
AF22
Y19
O/Z
SDRAM row-address strobe/SBSRAM output-enable
SDWE/SSWE
AC20
AA20
O/Z
SDRAM write-enable/SBSRAM write-enable
HOLD
Y26
V22
I
Hold request from the host
HOLDA
V23
U21
O
Hold-request-acknowledge to the host
TOUT0
F1
D1
O
Timer 0 or general-purpose output
TINP0
H4
E2
I
Timer 0 or general-purpose input
TOUT1
J4
F2
O
Timer 1 or general-purpose output
TINP1
G2
F3
I
Timer 1 or general-purpose input
DMAC3
Y3
V3
DMAC2
AA2
W2
DMAC1
AB1
AA1
DMAC0
AA3
W3
EMIF − BUS ARBITRATION
TIMER 0
TIMER 1
DMA ACTION COMPLETE STATUS
†
O
DMA action complete
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
27
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
CLKS0
M4
K3
I
CLKR0
M2
L2
I/O/Z
External clock source (as opposed to internal)
Receive clock
CLKX0
M3
K1
I/O/Z
Transmit clock
DR0
R2
M2
I
Receive data
DX0
P4
M3
O/Z
Transmit data
FSR0
N3
M1
I/O/Z
Receive frame sync
FSX0
N4
L3
I/O/Z
Transmit frame sync
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
CLKS1
G1
E1
I
CLKR1
J3
G2
I/O/Z
External clock source (as opposed to internal)
Receive clock
CLKX1
H2
G3
I/O/Z
Transmit clock
DR1
L4
H1
I
Receive data
DX1
J1
H2
O/Z
Transmit data
FSR1
J2
H3
I/O/Z
Receive frame sync
FSX1
K4
G1
I/O/Z
Transmit frame sync
MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP2)
CLKS2
R3
N1
I
CLKR2
T2
N2
I/O/Z
External clock source (as opposed to internal)
Receive clock
CLKX2
R4
N3
I/O/Z
Transmit clock
DR2
V1
R2
I
Receive data
DX2
T4
R1
O/Z
Transmit data
FSR2
U2
P3
I/O/Z
Receive frame sync
FSX2
T3
P2
I/O/Z
Transmit frame sync
RSV0
L3
J2
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV1
G3
E3
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RESERVED FOR TEST
†
RSV2
A12
B11
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV3
C15
B13
O
Reserved (leave unconnected, do not connect to power or ground)
RSV4
D12
C10
O
Reserved (leave unconnected, do not connect to power or ground)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
28
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
SUPPLY VOLTAGE PINS
A11
DVDD
†
A3
A16
A7
B7
A16
B8
A20
B19
D4
B20
D6
C6
D7
C10
D9
C14
D10
C17
D13
C21
D14
G4
D16
G23
D17
H3
D19
H24
F1
K3
F4
K24
F19
L1
F22
L26
G4
N24
G19
P3
J4
T1
J19
T26
K4
U3
K19
U24
L1
W3
M22
W24
N4
Y4
N19
Y23
P4
AD6
P19
AD10
T4
AD13
T19
AD17
U1
AD21
U4
AE7
U19
AE8
U22
AE19
W4
AE20
W6
AF11
W7
S
3.3-V
3.3
V supply voltage (I/O)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
29
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
SUPPLY VOLTAGE PINS (CONTINUED)
DVDD
CVDD
†
AF16
W9
−
W10
−
W13
−
W14
−
W16
−
W17
−
W19
−
AB5
−
AB9
−
AB14
−
AB18
A1
E7
A2
E8
A3
E10
A24
E11
A25
E12
A26
E13
B1
E15
B2
E16
B3
F7
B24
F8
B25
F9
B26
F11
C1
F12
C2
F14
C3
F15
C4
F16
C23
G5
C24
G6
C25
G17
C26
G18
D3
H5
D4
H6
D5
H17
D22
H18
D23
J6
D24
J17
E4
K5
E23
K18
AB4
L5
S
3.3-V
3.3
V supply voltage (I/O)
S
1 5 V supply
l voltage
lt
(
) (C6202B only)
l )
1.5-V
(core)
1.8-V
1 8-V supply voltage (core) (C6202 only)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
30
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
SUPPLY VOLTAGE PINS (CONTINUED)
CVDD
AB23
L6
AC3
L17
AC4
L18
AC5
M5
AC22
M6
AC23
M17
AC24
M18
AD1
N5
AD2
N18
AD3
P6
AD4
P17
AD23
R5
AD24
R6
AD25
R17
AD26
R18
AE1
T5
AE2
T6
AE3
T17
AE24
T18
AE25
U7
AE26
U8
AF1
U9
AF2
U11
AF3
U12
AF24
U14
AF25
U15
AF26
U16
−
V7
−
V8
−
V10
−
V11
−
V12
−
V13
−
V15
−
V16
S
1.5-V
1
5 V supply
l voltage
lt
(core)
(
) (C6202B only)
l )
1.8-V
1 8-V supply voltage (core) (C6202 only)
GROUND PINS
A4
VSS
†
A1
A8
A5
A13
A12
A14
A18
GND
Ground pins
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
31
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
GROUND PINS (CONTINUED)
A15
VSS
A22
A19
B2
A23
B21
B4
C1
B12
C3
B13
C20
B14
C22
B23
D5
C5
D8
C11‡
D11
C16
D12
C22
D15
D1
D18
D2
E4
D6
E5
D21
E6
D25
E9
D26
E14
E3
E17
E24
E18
F4
E19
F23
F5
H1
F6
H26
F10
K1
F13
K26
F17
M1
F18
M26
H4
N1
H19
N2
J1
N25
J5
N26
J18
P1
J22
P2
K6
P25
K17
P26
L4
GND
Ground pins
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
‡ For the C6202 GJL package only, the C11 pin is ground (V ). For all C62x GNZ packages, the C11 pin is CLKMODE1.
SS
32
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
GROUND PINS (CONTINUED)
R1
VSS
†
L19
R26
M4
U1
M19
U26
N6
W1
N17
W26
P1
AA4
P5
AA23
P18
AB3
P22
AB24
R4
AC1
R19
AC2
U5
AC6
U6
AC21
U10
AC25
U13
AC26
U17
AD5
U18
AD22
V4
AE4
V5
AE13
V6
AE14
V9
AE23
V14
AF4
V17
AF8
V18
AF10
V19
AF12
W5
AF13
W8
AF14
W11
AF15
W12
AF17
W15
AF19
W18
AF23
Y1
—
Y3
—
Y20
—
Y22
—
AA2
—
AA21
GND
Ground pins
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
33
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJL/
GLS/
GNZ
GNY
DESCRIPTION
TYPE†
GROUND PINS (CONTINUED)
VSS
†
—
AB1
—
AB3
—
AB7
—
AB11
—
AB16
—
AB20
—
AB22
GND
Ground pins
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
development support
TI offers an extensive line of development tools for the TMS320C6000 DSP platform, including tools to evaluate
the performance of the processors, generate code, develop algorithm implementations, and fully integrate and
debug software and hardware modules.
The following products support development of C6000 DSP-based applications:
Software Development Tools:
Code Composer Studio Integrated Development Environment (IDE) including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS) Emulator (supports C6000 DSP multiprocessor system debug)
EVM (Evaluation Module)
For a complete listing of development-support tools for the TMS320C6000 DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL). For
information on pricing and availability, contact the nearest TI field sales office or authorized distributor.
Code Composer Studio, DSP/BIOS, XDS, and TMS320 are trademarks of Texas Instruments.
34
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
device and development-support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all TMS320
DSP devices and support tools. Each TMS320 DSP commercial family member has one of three prefixes: TMX,
TMP, or TMS. Texas Instruments recommends two of three possible prefix designators for support tools: TMDX
and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes
(TMX / TMDX) through fully qualified production devices/tools (TMS / TMDS).
Device development evolutionary flow:
TMX
Experimental device that is not necessarily representative of the final device’s electrical
specifications
TMP
Final silicon die that conforms to the device’s electrical specifications but has not completed
quality and reliability verification
TMS
Fully qualified production device
Support tool development evolutionary flow:
TMDX
Development-support product that has not yet completed Texas Instruments internal qualification
testing.
TMDS
Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer:
“Developmental product is intended for internal evaluation purposes.”
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI’s standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GLS), the temperature range (for example, blank is the default commercial temperature range),
and the device speed range in megahertz (for example, -250 is 250 MHz).
Table 16 lists the device orderable part numbers (P/Ns) and Figure 4 provides a legend for reading the complete
device name for any member of the TMS320C6000 DSP platform. For more information on the C6202/02B
device orderable P/Ns, visit the Texas Instruments web site on the Worldwide web at http://www.ti.com URL,
or contact the nearest TI field sales office or authorized distributor.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
35
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
device and development-support tool nomenclature (continued)
Table 16. TMS320C6202/02B Device Part Numbers (P/Ns) and Ordering Information
DEVICE ORDERABLE P/N
CVDD
(CORE VOLTAGE)
DEVICE SPEED
DVDD
(I/O VOLTAGE)
OPERATING CASE
TEMPERATURE
RANGE
C6202
TMS320C6202GJL200
200 MHz/1600 MIPS
1.8 V
3.3 V
0_C to 90_C
TMS320C6202GJL250
250 MHz/2000 MIPS
1.8 V
3.3 V
0_C to 90_C
TMS320C6202GJLA200
200 MHz/1600 MIPS
1.8 V
3.3 V
−40_C to105_C
TMS320C6202GLS200
200 MHz/1600 MIPS
1.8 V
3.3 V
0_C to 90_C
TMS320C6202GLS250
250 MHz/2000 MIPS
1.8 V
3.3 V
0_C to 90_C
TMS320C6202BGNY250
250 MHz/2000 MIPS
1.5 V
3.3 V
0_C to 90_C
TMS320C6202BGNY300
300 MHz/2400 MIPS
1.5 V
3.3 V
0_C to 90_C
TMS320C6202BGNZ250
250 MHz/2000 MIPS
1.5 V
3.3 V
0_C to 90_C
TMS320C6202BGNZ300
300 MHz/2400 MIPS
1.5 V
3.3 V
0_C to 90_C
TMS32C6202BGNZA250
250 MHz/2000 MIPS
1.5 V
3.3 V
−40_C to 105_C
C6202B
TMS 320
C 6202
GLS
( )
−250
PREFIX
TMX = Experimental device
TMP = Prototype device
TMS = Qualified device
SMJ = MIL-PRF-38535, QML
SM = High Rel (non-38535)
DEVICE SPEED RANGE
100 MHz
120 MHz
150 MHz
167 MHz
DEVICE FAMILY
320 = TMS320t DSP family
TEMPERATURE RANGE (DEFAULT: 0°C TO 90°C)
Blank = 0°C to 90°C, commercial temperature
A
= −40°C to 105°C, extended temperature
DEVICE
C6000 DSP:
6201
6202
6202B
6203B
6204
BGA =
500 MHz
600 MHz
PACKAGE TYPE†
GFN = 256-pin plastic BGA
GGP = 352-pin plastic BGA
GJC = 352-pin plastic BGA
GJL = 352-pin plastic BGA
GLS = 384-pin plastic BGA
GLW = 340-pin plastic BGA
GNY = 384-pin plastic BGA
GNZ = 352-pin plastic BGA
GHK = 288-pin plastic MicroStar BGAt
TECHNOLOGY
C = CMOS
†
200 MHz
233 MHz
250 MHz
300 MHz
6205
6211
6211B
6411
6414
6415
6416
6701
6711
6711B
6711C
6712
6712C
6713
Ball Grid Array
Figure 4. TMS320C6000 DSP Platform Device Nomenclature (Including TMS320C6202 and C6202B)
MicroStar BGA is a trademark of Texas Instruments.
36
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
documentation support
Extensive documentation supports all TMS320 DSP family devices from product announcement through
applications development. The types of documentation available include: data sheets, such as this document,
with design specifications; complete user’s reference guides for all devices and tools; technical briefs;
development-support tools; on-line help; and hardware and software applications. The following is a brief,
descriptive list of support documentation specific to the C6000 DSP devices:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 CPU (DSP core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190) briefly
describes the functionality of the peripherals available on the C6000 DSP platform of devices, such as the
64-/32-/16-bit external memory interfaces (EMIFs), 32-/16-bit host-port interfaces (HPIs), multichannel buffered
serial ports (McBSPs), direct memory access (DMA), enhanced direct-memory-access (EDMA) controller,
expansion bus (XBus), peripheral component interconnect (PCI), clocking and phase-locked loop (PLL); and
power-down modes.
The How to Begin Development Today and Migrate Across the TMS320C6202/02B/03B/04 DSPs Application
Report (literature number SPRA603) describes the migration concerns and identifies the similarities and
differences between the C6202, C6202B, C6203B, and C6204 C6000 DSP devices.
The TMS320C6202, TMS320C6202B Digital Signal Processors Silicon Errata (literature number SPRZ152)
describes the known exceptions to the functional specifications for particular silicon revisions of the
TMS320C6202 device . There are currently no known silicon advisories on the TMS320C6202B device.
The Using IBIS Models for Timing Analysis Application Report (literature number SPRA839) describes how to
properly use IBIS models to attain accurate timing analysis for a given system.
The tools support documentation is electronically available within the Code Composer Studio IDE. For a
complete listing of the latest C6000 DSP documentation, visit the Texas Instruments web site on the Worldwide
Web at http://www.ti.com uniform resource locator (URL).
clock PLL
All of the internal C6202/02B clocks are generated from a single source through the CLKIN pin. This source
clock either drives the PLL, which multiplies the source clock in frequency to generate the internal CPU clock,
or bypasses the PLL to become the internal CPU clock.
To use the PLL to generate the CPU clock, the external PLL filter circuit must be properly designed. Figure 5,
and Table 17 through Table 20 show the external PLL circuitry for either x1 (PLL bypass) or x4 PLL multiply
modes. Figure 6 shows the external PLL circuitry for a system with ONLY x1 (PLL bypass) mode.
To minimize the clock jitter, a single clean power supply should power both the C6202/02B device and the
external clock oscillator circuit. Noise coupling into PLLF directly impacts PLL clock jitter. The minimum CLKIN
rise and fall times should also be observed. For the input clock timing requirements, see the Input and Output
Clocks electricals section.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
37
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
clock PLL (continued)
3.3V
EMI Filter
PLLV
C3
10 mF
C4
0.1 mF
Internal to
C6202/02B
PLL
CLKMODE0
CLKMODE1†
CLKMODE2†
PLLMULT
PLLCLK
CLKIN
CLKIN
1
LOOP FILTER
PLLF
(For the PLL Options
and CLKMODE pins setup,
see Table 17 through Table 20)
C2
C1
CPU
CLOCK
PLLG
0
R1
† CLKMODE1 and CLKMODE2 pins are not applicable (N/A) to the C6202 GJL package. The CLKMODE2 pin is also N/A on the C6202B GNZ package.
NOTES: A. Keep the lead length and the number of vias between pin PLLF, pin PLLG, R1, C1, and C2 to a minimum. In addition, place all PLL
components (R1, C1, C2, C3, C4, and EMI Filter) as close to the C6000 DSP device as possible. Best performance is achieved with
the PLL components on a single side of the board without jumpers, switches, or components other than the ones shown.
B. For reduced PLL jitter, maximize the spacing between switching signals and the PLL external components (R1, C1, C2, C3, C4,
and the EMI Filter).
C. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
D. EMI filter manufacturer: TDK part number ACF451832-333, 223, 153, 103. Panasonic part number EXCCET103U.
Figure 5. External PLL Circuitry for Either PLL Multiply Modes or x1 (Bypass) Mode
3.3V
PLLV
CLKMODE0
CLKMODE1†
CLKMODE2†
PLLMULT
Internal to
C6202/02B
PLL
PLLCLK
CLKIN
CLKIN
LOOP FILTER
1
CPU
CLOCK
PLLG
PLLF
0
† CLKMODE1 and CLKMODE2 pins are not applicable (N/A) to the C6202 GJL package. The CLKMODE2 pin is also N/A on the C6202B GNZ package.
NOTES: A. For a system with ONLY PLL x1 (bypass) mode, short the PLLF to PLLG.
B. The 3.3-V supply for PLLV must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
Figure 6. External PLL Circuitry for x1 (Bypass) PLL Mode Only
38
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
clock PLL (continued)
Table 17. TMS320C6202 GLS and C6202B GNY Packages PLL Multiply and Bypass (x1) Options†
GLS PACKAGE − 18 X 18 MM BGA [C6202 ONLY] AND
GNY PACKAGE − 18 X 18 MM BGA [C6202B ONLY]
BIT (PIN NO
NO.))
CLKMODE2 (A14)
CLKMODE1 (A9)
CLKMODE0 (B12)
0
0
0
0
0
0
Value
†
‡
DEVICES AND PLL CLOCK OPTIONS
C6202 (GLS)‡
C6202B (GNY)
0
Bypass (x1)
Bypass (x1)
1
x4
x4
1
0
Bypass (x1)
x8
1
1
x4
x10
1
0
0
Bypass (x1)
x6
1
0
1
x4
x9
1
1
0
Bypass (x1)
x7
1
1
1
x4
x11
f(CPU Clock) = f(CLKIN) x (PLL mode)
For the C6202 GLS package, the CLKMODE2 (A14) and CLKMODE1 (A9) pins are internally unconnected.
Table 18. TMS320C6202 GJL and TMS320C6202B GNZ Packages PLL Multiply and Bypass (x1) Options†
GJL PACKAGE 27 x 27 mm BGA [C6202 only] and
GNZ PACKAGE − 27 x 27 mm BGA [C6202B only]
BIT (PIN NO
NO.))
CLKMODE2 (N/A)§
Value
†
§
CLKMODE1 (C11)§
CLKMODE0 (B15)
0
0
1
0
1
1
N/A
DEVICES AND PLL CLOCK OPTIONS
C6202 (GJL)§
C6202B (GNZ)§
0
Bypass (x1)
Bypass (x1)
1
x4
x4
x8
N/A
x10
f(CPU Clock) = f(CLKIN) x (PLL mode)
CLKMODE2 and CLKMODE1 pins are not available on the C6202 GJL package.
The CLKMODE2 pin is not available (N/A) on the C6202B GNZ package.
Table 19. TMS320C6202 PLL Component Selection Table†
†
CLKMODE
CLKIN
RANGE
(MHz)
CPU CLOCK
FREQUENCY
(CLKOUT1)
RANGE (MHz)
CLKOUT2
RANGE
(MHz)
R1 [±1%]
C1 [±10%]
C2 [±10%]
TYPICAL
LOCK TIME
(µs)
x4
32.5−62.5
130−250
65−125
60.4 Ω
27 nF
560 pF
75
Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
39
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
clock PLL (continued)
Table 20. TMS320C6202B PLL Component Selection Table†
CLKMODE‡
CLKIN
RANGE
(MHz)
x4
32.5−75
x6
21.7−50
x7
18.6−42.9
x8
16.3−37.5
x9
14.4−33.3
x10
13−30
x11
11.8−27.3
CPU CLOCK
FREQUENCY
RANGE (MHz)
CLKOUT2
RANGE
(MHz)
R1 [±1%]
C1 [±10%]
C2 [±10%]
TYPICAL
LOCK TIME
(µs)
130−300
130
300
65−150
65
150
45.3 Ω
47 nF
10 pF
75
†
Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
‡ CLKMODE x1, x4, x6, x7, x8, x9, x10, and x11 apply to the C6202B GNY devices. The C6202B GNZ device is restricted to x1, x4, x8, and x10
multiply factors.
power-down mode logic
Figure 7 shows the power-down logic on for the 6202/6202B.
CLKOUT1
TMS320C6202/C6202B
Internal Clock Tree
PD1
PD2
PD
(pin)
PowerDown
Logic
Clock
PLL
IFR
IER
Internal
Peripheral
PWRD CSR
CPU
PD3
CLKIN
RESET
Figure 7. Power-Down Mode Logic
40
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
Internal
Peripheral
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
triggering, wake-up, and effects
The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 10−15)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 8 and described in Table 21.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
writing to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the TMS320C6000 CPU
and Instruction Set Reference Guide (literature number SPRU189).
31
16
15
14
13
12
11
10
Reserved
Enable or
non-enabled
interrupt wake
Enabled
interrupt wake
PD3
PD2
PD1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
7
9
8
0
Legend: R/W−x = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 8. PWRD Field of the CSR Register
Power-down mode PD1 takes effect eight to nine clock cycles after the instruction that sets the PWRD bits in the
CSR.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where PD1
took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed first,
then the program execution returns to the instruction where PD1 took effect. The GIE bit in CSR and the NMIE
bit in the interrupt enable register (IER) must also be set in order for the interrupt service routine to execute;
otherwise, execution returns to the instruction where PD1 took effect upon PD1 mode termination by an enabled
interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 21 summarizes all the power-down modes.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
41
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
triggering, wake-up, and effects (continued)
Table 21. Characteristics of the Power-Down Modes
PRWD
BITS 15−10
POWER-DOWN
MODE
WAKE-UP METHOD
EFFECT ON CHIP’S OPERATION
000000
No power-down
—
001001
PD1
Wake by an enabled interrupt
010001
PD1
Wake by an enabled or
non-enabled interrupt
011010
PD2†
Wake by a device reset
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
halted. Signal terminal PD is driven high. All register and internal
RAM contents are preserved. All functional I/O “freeze” in the last
state when the PLL clock is turned off.‡
011100
PD3†
Wake by a device reset
Input clock to the PLL stops generating clocks. Signal terminal PD
is driven high. All register and internal RAM contents are preserved.
All functional I/O “freeze” in the last state when the PLL clock is
turned off.† Following reset, the PLL needs time to re-lock, just as
it does following power-up.
Wake-up from PD3 takes longer than wake-up from PD2 because
the PLL needs to be re-locked.
Reserved
—
other
CPU halted (except for the interrupt logic)
Power
down mode blocks the internal clock inputs at the
Power-down
boundary of the CPU, preventing most of its logic from
switching. During PD1, DMA transactions can proceed between
peripherals and internal memory.
†
On the C6202/C6202B, both the PD2 and PD3 signals assert the PD pin for external recognition of these two power-down modes.
‡ When entering PD2 and PD3, all functional I/O will remain in the previous state. However, for peripherals which are asynchronous in nature
(HPI) or peripherals with an external clock source (McBSP, XBUS, timers), output signals may transition in response to stimulus on the inputs.
Peripheral operation may not perform as intended under these conditions.
peripheral power-down mode for TMS320C6202/6202B
The C6202/C6202B has the ability to turn off clocks to individual peripherals on the device. This feature allows
the user to selectively turn off peripherals which are not being used for a specific application and not pay the
extra price in power consumption for unused peripherals.
The Figure 9 title displays the peripheral power down register address location and Figure 9 itself shows the
register fields.
31
16
Reserved
R-0
15
8
Reserved
R-0
7
5
4
3
2
1
0
Reserved
MCBSP2
MCBSP1
MCBSP0
EMIF
DMA
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
Legend: R/W−x = Read/write reset value
Figure 9. Peripheral Power-Down Control Register (PDCTL) for TMS320C6202/6202B (019C 0200h)
42
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
peripheral power-down mode for TMS320C6202/6202B (continued)
Table 22 lists and describes the fields in the peripheral power-down control register (PDCTL).
Table 22. Power-Down Control Register (PDCTL) Field Descriptions
BIT
FIELD
31−5
Reserved
Reserved. The reserved bit location is always read as zero. A value written to this field has no
effect.
4
MCBSP2
Internal McBSP2 clock enable bit.
3
2
1
0
VALUES
DESCRIPTION
0
Internal McBSP2 clock is enabled.
1
Internal McBSP2 clock is disabled. McBSP2 is not functional.
MCBSP1
Internal McBSP1 clock enable bit.
0
Internal McBSP1 clock is enabled.
1
Internal McBSP1 clock is disabled. McBSP1 is not functional.
MCBSP0
Internal McBSP0 clock enable bit.
0
Internal McBSP0 clock is enabled.
1
Internal McBSP0 clock is disabled. McBSP1 is not functional.
EMIF
Internal EMIF clock enable bit.
0
Internal EMIF clock is enabled.
1
Internal EMIF clock is disabled. EMIF is not functional.
DMA
Internal DMA clock enable bit.
0
Internal DMA clock is enabled.
1
Internal DMA clock is disabled. DMA is not functional.
The user must be careful to not disable a portion of the device which is being used, since the peripheral becomes
non-operational once disabled. A clock-off mode can be entered and exited depending on the needs of the
application. For example, if an application does not need the serial ports, the ports can be disabled and then
re-enabled when needed. While a peripheral is in power-down mode, no writes to the peripheral’s registers will
occur; and reads from the peripheral will produce invalid data.
When re-enabling any of the peripheral power-down bits, the CPU should wait at least 5 additional clock cycles
before attempting to access that peripheral.
power-supply sequencing
TI DSPs do not require specific power sequencing between the core supply and the I/O supply. However,
systems should be designed to ensure that neither supply is powered up for extended periods of time
(>1 second) if the other supply is below the proper operating voltage.
system-level design considerations
System-level design considerations, such as bus contention, may require supply sequencing to be
implemented. In this case, the core supply should be powered up at the same time as, or prior to (and powered
down after), the I/O buffers. This is to ensure that the I/O buffers receive valid inputs from the core before the
output buffers are powered up, thus, preventing bus contention with other chips on the board.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
43
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
power-supply design considerations
A dual-power supply with simultaneous sequencing can be used to eliminate the delay between core and I/O
power up. A Schottky diode can also be used to tie the core rail to the I/O rail (see Figure 10).
I/O Supply
DVDD
Schottky
Diode
C6000
DSP
Core Supply
CVDD
VSS
GND
Figure 10. Schottky Diode Diagram
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000 platform of DSPs, the PC board should include separate power planes for core,
I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
On systems using C62x and C67x DSPs, the core may consume in excess of 2 A per DSP until the I/O supply
powers on. This extra current results from uninitialized logic within the DSP(s). A normal current state returns
once the I/O power supply turns on and the CPU sees a clock pulse. Decreasing the amount of time between
the core supply power-up and the I/O supply power-up reduces the effects of the current draw. If the external
supply to the DSP core cannot supply the excess current, the minimum core voltage may not be achieved until
after normal current returns. This voltage starvation of the core supply during power up does not affect run-time
operation. Voltage starvation can affect power supply systems that gate the I/O supply via the core supply,
causing the I/O supply to never turn on. During the transition from excess to normal current, a voltage spike may
be seen on the core supply. Care must be taken when designing overvoltage protection circuitry on the core
supply to not restart the power sequence due to this spike. Otherwise, the supply may cycle indefinitely.
44
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
IEEE 1149.1 JTAG compatibility statement
For compatibility with IEEE 1149.1 JTAG programmers, the TRST pin may need to be externally pulled up via
a 1-kΩ resistor. For these C62x devices, this pin is internally pulled down, holding the JTAG port in reset by
default. This is typically only a problem in systems where the DSP shares a scan chain with some other device.
Some JTAG programmers for these other devices do not actively drive TRST high, leaving the scan chain
inoperable while the C62x JTAG port is held in reset. TI emulators do drive TRST high, so the external pullup
resistor is not needed in systems where TI emulators are the only devices that control JTAG scan chains on
which the DSP(s) reside. If the system has other devices in the same scan chain as the DSP, and the
programmer for these devices does not drive TRST high, then an external 1-kΩ pullup resistor is required.
With this external 1-kΩ pullup resistor installed, care must be taken to keep the DSP in a usable state under
all circumstances. When TRST is pulled up, the JTAG driver must maintain the TMS signal high for 5 TCLK
cycles, forcing the DSP(s) into the test logic reset (TLR) state. From the TLR state, the DSP’s data scan path
can be put in bypass (scan all 1s into the IR) to scan the other devices. The TLR state also allows normal
operation of the DSP. If operation without anything driving the JTAG port is desired, the pullup resistor should
be jumpered so that it can be engaged for programming the other devices and disconneted for running without
a JTAG programmer or emulator.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
45
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
absolute maximum ratings over operating case temperature ranges (unless otherwise noted)†
Supply voltage range, CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to 2.3 V
Supply voltage range, DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Operating case temperature ranges, TC: (default) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0_C to 90_C
(A version): C6202BGNZA-250 . . . . . . . . . . . . . . . . . −40_C to105_C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65_C to 150_C
Temperature cycle range, (1000-cycle performance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40_C to 125_C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
recommended operating conditions
MIN
NOM
MAX
UNIT
CVDD
Supply voltage, Core
C6202B only
1.43
1.5
1.57
V
CVDD
Supply voltage, Core
C6202 only
1.71
1.8
1.89
V
DVDD
Supply voltage, I/O
3.14
3.3
3.46
V
VSS
Supply ground
0
0
0
V
VIH
High-level input voltage
2
VIL
Low-level input voltage
0.8
V
IOH
High-level output current
−8
mA
IOL
Low-level output current
TC
Default
Operating case temperature
A version: C6202BGNZA-250
V
8
mA
0
90
_C
−40
105
_C
electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
PARAMETER
§
MIN
TYP
MAX
DVDD = MIN,
IOH = MAX
VOL
Low-level output voltage
DVDD = MIN,
IOL = MAX
0.6
V
II
Input current‡
VI = VSS to DVDD
±10
uA
IOZ
Off-state output current
VO = DVDD or 0 V
±10
uA
IDD2V
Supply current, CPU + CPU memory
access§
C6202, CVDD = NOM, CPU clock = 200 MHz
520
mA
C6202B, CVDD = NOM, CPU clock = 200 MHz
340
mA
C6202, CVDD = NOM, CPU clock = 200 MHz
390
mA
C6202B, CVDD = NOM, CPU clock = 200 MHz
Supply current,
current peripherals§
2.4
UNIT
High-level output voltage
IDD2V
‡
TEST CONDITIONS
VOH
V
235
mA
C6202, DVDD = NOM, CPU clock = 200 MHz
70
mA
C6202B, DVDD = NOM, CPU clock = 200 MHz
45
IDD3V
current I/O pins§
Supply current,
Ci
Input capacitance
10
pF
Co
Output capacitance
10
pF
mA
TMS and TDI are not included due to internal pullups. TRST is not included due to internal pulldown.
Measured with average activity (50% high / 50% low power). For more details on CPU, peripheral, and I/O activity, see the TMS320C62x/C67x
Power Consumption Summary application report (literature number SPRA486).
46
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
PARAMETER MEASUREMENT INFORMATION
IOL
Tester Pin
Electronics
50 Ω
Vcomm
Output
Under
Test
CT†
IOH
Where:
†
Typical distributed load circuit capacitance
IOL
IOH
Vcomm
CT
=
=
=
=
2 mA
2 mA
1.5 V
15-pF typical load-circuit capacitance
Figure 11. Test Load Circuit for AC Timing Measurements
signal transition levels
All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
Vref = 1.5 V
Figure 12. Input and Output Voltage Reference Levels for ac Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, and
VOL MAX and VOH MIN for output clocks.
Vref = VIH MIN (or VOH MIN)
Vref = VIL MAX (or VOL MAX)
Figure 13. Rise and Fall Transition Time Voltage Reference Levels
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
47
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
timing parameters and board routing analysis
The timing parameter values specified in this data sheet do not include delays by board routings. As a good
board design practice, such delays must always be taken into account. Timing values may be adjusted by
increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification
(IBIS) models to analyze the timing characteristics correctly. To properly use IBIS models to attain accurate
timing analysis for a given system, see the Using IBIS Models for Timing Analysis Application Report (literature
number SPRA839). If needed, external logic hardware such as buffers may be used to compensate any timing
differences.
For inputs, timing is most impacted by the round-trip propagation delay from the DSP to the external device and
from the external device to the DSP. This round-trip delay tends to negatively impact the input setup time margin,
but also tends to improve the input hold time margins (see Table 23 and Figure 14).
Figure 14 represents a general transfer between the DSP and an external device. The figure also represents
board route delays and how they are perceived by the DSP and the external device.
Table 23. Board-Level TImings Example (see Figure 14)
NO.
DESCRIPTION
1
Clock route delay
2
Minimum DSP hold time
3
Minimum DSP setup time
4
External device hold time requirement
5
External device setup time requirement
6
Control signal route delay
7
External device hold time
8
External device access time
9
DSP hold time requirement
10
DSP setup time requirement
11
Data route delay
CLKOUT2
(Output from DSP)
1
CLKOUT2
(Input to External Device)
Control Signals†
(Output from DSP)
2
3
5
Control Signals
(Input to External Device)
4
6
Data Signals‡
(Output from External Device)
Data Signals‡
(Input to DSP)
7
8
11
10
9
† Control signals include data for Writes.
‡ Data signals are generated during Reads from an external device.
Figure 14. Board-Level Input/Output Timings
48
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS
timing requirements for CLKIN (PLL used)†‡§ (see Figure 15)
C6202-250
C6202B-250
C6202-200
NO.
MIN
MAX
MIN
C6202B-300
MAX
MIN
UNIT
MAX
1
tc(CLKIN)
Cycle time, CLKIN
5*M
4*M
3.33 * M
ns
2
tw(CLKINH)
Pulse duration, CLKIN high
0.4C
0.4C
0.4C
ns
3
tw(CLKINL)
Pulse duration, CLKIN low
0.4C
0.4C
0.4C
ns
4
tt(CLKIN)
Transition time, CLKIN
5
5
5
ns
†
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
‡ M = the PLL multiplier factor (x4, x6, x7, x8, x9, x10, or x11) for C6202 GLS and C6202B GNY only.
M = the PLL multiplier factor (x4, x6, x8, or x10) for C6202B GNZ only.
For more details, see the Clock PLL section of this data sheet.
§ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns.
timing requirements for CLKIN [PLL bypassed (x1)]†¶ (see Figure 15)
C6202-250
C6202B-250
C6202-200
NO.
MIN
MAX
MIN
MAX
C6202B-300
MIN
UNIT
MAX
1
tc(CLKIN)
Cycle time, CLKIN
5
4
3.33
ns
2
tw(CLKINH)
Pulse duration, CLKIN high
0.45C
0.45C
0.45C
ns
3
tw(CLKINL)
Pulse duration, CLKIN low
0.45C
4
tt(CLKIN)
Transition time, CLKIN
0.45C
0.6
0.45C
0.6
ns
0.6
ns
†
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
¶ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns. The maximum CLKIN cycle time is PLL bypass mode
(x1) is 200 MHz.
1
4
2
CLKIN
3
4
Figure 15. CLKIN Timings
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
49
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
timing requirements for XCLKIN† (see Figure 16)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
†
1
tc(XCLKIN)
Cycle time, XCLKIN
2
tw(XCLKINH)
3
tw(XCLKINL)
UNIT
MAX
4P
ns
Pulse duration, XCLKIN high
1.8P
ns
Pulse duration, XCLKIN low
1.8P
ns
P = 1/CPU clock frequency in nanoseconds (ns).
1
2
XCLKIN
3
Figure 16. XCLKIN Timings
switching characteristics over recommended operating conditions for CLKOUT2ठ(see Figure 17)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
MAX
2
tw(CKO2H)
Pulse duration, CLKOUT2 high
P − 0.7
P + 0.7
ns
3
tw(CKO2L)
Pulse duration, CLKOUT2 low
P − 0.7
P + 0.7
ns
‡
P = 1/CPU clock frequency in ns.
§ The reference points for the rise and fall transitions are measured at V
OL MAX and VOH MIN.
1
2
CLKOUT2
3
Figure 17. CLKOUT2 Timings
50
UNIT
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
switching characteristics over recommended operating conditions for XFCLK†‡ (see Figure 18)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
UNIT
MAX
1
tc(XFCK)
Cycle time, XFCLK
D * P − 0.7
D * P + 0.7
ns
2
tw(XFCKH)
Pulse duration, XFCLK high
(D/2) * P − 0.7
(D/2) * P + 0.7
ns
3
tw(XFCKL)
Pulse duration, XFCLK low
(D/2) * P − 0.7
(D/2) * P + 0.7
ns
†
P = 1/CPU clock frequency in ns.
‡ D = 8, 6, 4, or 2; FIFO clock divide ratio, user-programmable
1
2
XFCLK
3
Figure 18. XFCLK Timings
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
51
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING
timing requirements for asynchronous memory cycles†‡§¶ (see Figure 19 − Figure 22)
C6202-200
C6202-250
NO.
MIN
3
tsu(EDV-AREH)
Setup time, EDx valid before
ARE high
4
th(AREH-EDV)
Hold time, EDx valid after
ARE high
6
tsu(ARDYH-AREL)
Setup time, ARDY high before
ARE low
7
th(AREL-ARDYH)
Hold time, ARDY high after
ARE low
9
tsu(ARDYL-AREL)
Setup time, ARDY low before
ARE low
10
th(AREL-ARDYL)
Hold time, ARDY low after
ARE low
11
tw(ARDYH)
Pulse width, ARDY high
15
tsu(ARDYH-AWEL)
Setup time, ARDY high before
AWE low
16
th(AWEL-ARDYH)
Hold time, ARDY high after
AWE low
18
tsu(ARDYL-AWEL)
Setup time, ARDY low before
AWE low
19
th(AWEL-ARDYL)
Hold time, ARDY low after
AWE low
C6202B-250
C6202B-300
MAX
MIN
UNIT
MAX
1
1
ns
3.5
4.9
ns
−[(RST − 3) * P − 6]
−[(RST − 3) * P − 6]
ns
(RST − 3) * P + 2
(RST − 3) * P + 2
ns
−[(RST − 3) * P − 6]
−[(RST − 3) * P − 6]
ns
(RST − 3) * P + 2
(RST − 3) * P + 2
ns
2P
2P
ns
−[(WST − 3) * P − 6]
−[(WST − 3) * P − 6]
ns
(WST − 3) * P + 2
(WST − 3) * P + 2
ns
−[(WST − 3) * P − 6]
−[(WST − 3) * P − 6]
ns
(WST − 3) * P + 2
(WST − 3) * P + 2
ns
†
To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. If ARDY does meet setup or hold
time, it may be recognized in the current cycle or the next cycle. Thus, ARDY can be an asynchronous input.
‡ RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the EMIF CE space control registers.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
¶ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use ARDY input to extend strobe width.
52
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
switching characteristics over recommended operating conditions for asynchronous memory
cycles†‡§¶ (see Figure 19 − Figure 22)
NO.
C6202-200
C6202-250
PARAMETER
MIN
TYP
C6202B-250
C6202B-300
MAX
MIN
TYP
UNIT
MAX
1
tosu(SELV-AREL)
Output setup time, select
signals valid to ARE low
RS * P − 2
RS * P − 2
ns
2
toh(AREH-SELIV)
Output hold time, ARE high to
select signals invalid
RH * P − 2
RH * P − 2
ns
5
tw(AREL)
Pulse width, ARE low
8
td(ARDYH-AREH)
Delay time, ARDY high to
ARE high
3P
12
tosu(SELV-AWEL)
Output setup time, select
signals valid to AWE low
WS * P − 3
WS * P − 2
ns
13
toh(AWEH-SELIV)
Output hold time, AWE high
to select signals invalid
WH * P − 2
WH * P − 2
ns
14
tw(AWEL)
Pulse width, AWE low
17
td(ARDYH-AWEH)
Delay time, ARDY high to
AWE high
RST * P
RST * P
4P + 5
3P
WST * P
3P
ns
4P + 5
WST * P
4P + 5
3P
ns
ns
4P + 5
ns
†
RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the EMIF CE space control registers.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
§ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use ARDY input to extend strobe width.
¶ Select signals include: CEx, BE[3:0], EA[21:2], AOE; and for writes, include ED[31:0], with the exception that CEx can stay active for an additional
7P ns following the end of the cycle.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
53
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
1
2
1
2
1
2
CEx
BE[3:0]
EA[21:2]
3
4
ED[31:0]
1
2
AOE
6
7
ARE
5
AWE
ARDY
Figure 19. Asynchronous Memory Read Timing (ARDY Not Used)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
CLKOUT1
CEx
BE[3:0]
EA[21:2]
1
2
1
2
1
2
3
4
ED[31:0]
1
2
AOE
8
10
9
ARE
AWE
11
ARDY
Figure 20. Asynchronous Memory Read Timing (ARDY Used)
54
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2 Strobe = 3
Hold = 2
CLKOUT1
CEx
12
13
12
13
12
13
12
13
BE[3:0]
EA[21:2]
ED[31:0]
AOE
15
ARE
16
14
AWE
ARDY
Figure 21. Asynchronous Memory Write Timing (ARDY Not Used)
Setup = 2 Strobe = 3
Not Ready
Hold = 2
CLKOUT1
12
13
12
13
12
13
12
13
CEx
BE[3:0]
EA[21:2]
ED[31:0]
AOE
ARE
17
18
19
AWE
11
ARDY
Figure 22. Asynchronous Memory Write Timing (ARDY Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
55
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS-BURST MEMORY TIMING
timing requirements for synchronous-burst SRAM cycles for C6202 devices (see Figure 23)
NO
NO.
C6202-200
C6202-250
MIN
MIN
MAX
MAX
UNIT
7
tsu(EDV-CKO2H)
Setup time, read EDx valid before CLKOUT2 high
2.5
2.0
ns
8
th(CKO2H-EDV)
Hold time, read EDx valid after CLKOUT2 high
2.0
2.0
ns
switching characteristics over recommended operating conditions for synchronous-burst SRAM
cycles for C6202 devices†‡ (see Figure 23 and Figure 24)
NO
NO.
C6202-200
PARAMETER
MIN
1
tosu(CEV-CKO2H)
Output setup time, CEx valid before CLKOUT2 high
2
toh(CKO2H-CEV)
Output hold time, CEx valid after CLKOUT2 high
3
tosu(BEV-CKO2H)
Output setup time, BEx valid before CLKOUT2 high
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after CLKOUT2 high
5
tosu(EAV-CKO2H)
Output setup time, EAx valid before CLKOUT2 high
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after CLKOUT2 high
9
tosu(ADSV-CKO2H)
Output setup time, SDCAS/SSADS valid before CLKOUT2
high
10
toh(CKO2H-ADSV)
Output hold time, SDCAS/SSADS valid after CLKOUT2
high
11
tosu(OEV-CKO2H)
Output setup time, SDRAS/SSOE valid before CLKOUT2
high
12
toh(CKO2H-OEV)
Output hold time, SDRAS/SSOE valid after CLKOUT2 high
13
tosu(EDV-CKO2H)
Output setup time, EDx valid before CLKOUT2 high§
14
toh(CKO2H-EDIV)
Output hold time, EDx invalid after CLKOUT2 high
15
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE valid before CLKOUT2
high
16
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE valid after CLKOUT2 high
†
MAX
C6202-250
MIN
MAX
UNIT
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P − 1.2
P − 1.2
ns
P−4
P−3
ns
P − 0.8
P − 0.8
ns
P−4
P−3
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
‡
56
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
timing requirements for synchronous-burst SRAM cycles C6202B devices (see Figure 23)
C6202B-250
NO
NO.
MIN
MAX
C6202B-300
MIN
MAX
UNIT
7
tsu(EDV-CKO2H)
Setup time, read EDx valid before CLKOUT2 high
2.9
1.6
ns
8
th(CKO2H-EDV)
Hold time, read EDx valid after CLKOUT2 high
2.1
2.3
ns
switching characteristics over recommended operating conditions for synchronous-burst SRAM
cycles for C6202B devices†‡ (see Figure 23 and Figure 24)
NO
NO.
PARAMETER
C6202B-250
C6202B-300
MIN
MIN
MAX
MAX
UNIT
1
tosu(CEV-CKO2H)
Output setup time, CEx valid before CLKOUT2 high
P − 1.7
P−1
ns
2
toh(CKO2H-CEV)
Output hold time, CEx valid after CLKOUT2 high
P − 3.4
P − 2.7
ns
3
tosu(BEV-CKO2H)
Output setup time, BEx valid before CLKOUT2 high
P − 1.7
P−1
ns
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after CLKOUT2 high
P − 3.4
P − 2.7
ns
5
tosu(EAV-CKO2H)
Output setup time, EAx valid before CLKOUT2 high
P − 1.7
P−1
ns
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after CLKOUT2 high
P − 3.4
P − 2.7
ns
9
tosu(ADSV-CKO2H)
Output setup time, SDCAS/SSADS valid before CLKOUT2
high
P − 1.7
P−1
ns
10
toh(CKO2H-ADSV)
Output hold time, SDCAS/SSADS valid after CLKOUT2
high
P − 3.4
P − 2.7
ns
11
tosu(OEV-CKO2H)
Output setup time, SDRAS/SSOE valid before CLKOUT2
high
P − 1.7
P−1
ns
12
toh(CKO2H-OEV)
Output hold time, SDRAS/SSOE valid after CLKOUT2 high
P − 3.4
P − 2.7
ns
13
tosu(EDV-CKO2H)
Output setup time, EDx valid before CLKOUT2 high§
P − 2.3
P − 1.6
ns
14
toh(CKO2H-EDIV)
Output hold time, EDx invalid after CLKOUT2 high
P − 3.2
P − 2.5
ns
15
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE valid before CLKOUT2
high
P − 1.7
P−1
ns
16
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE valid after CLKOUT2 high
P − 3.4
P − 2.7
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
57
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
CLKOUT2
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
6
7
Q1
ED[31:0]
8
Q2
Q3
9
Q4
10
SDCAS/SSADS†
11
12
SDRAS/SSOE†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
Figure 23. SBSRAM Read Timing
CLKOUT2
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
Q1
Q2
Q3
Q4
6
13
ED[31:0]
14
9
10
15
16
SDCAS/SSADS†
SDRAS/SSOE†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SSADS, SSOE, and SSWE, respectively, during SBSRAM accesses.
Figure 24. SBSRAM Write Timing
58
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING
timing requirements for synchronous DRAM cycles for C6202 devices (see Figure 25)
NO
NO.
7
tsu(EDV-CKO2H)
Setup time, read EDx valid before CLKOUT2 high
8
th(CKO2H-EDV)
Hold time, read EDx valid after CLKOUT2 high
C6202-200
C6202-250
MIN
MIN
MAX
MAX
UNIT
1.2
1.2
ns
3
2.7
ns
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for C6202 devices†‡ (see Figure 25−Figure 30)
NO
NO.
C6202-200
PARAMETER
MIN
1
tosu(CEV-CKO2H)
Output setup time, CEx valid before CLKOUT2 high
2
toh(CKO2H-CEV)
Output hold time, CEx valid after CLKOUT2 high
3
tosu(BEV-CKO2H)
Output setup time, BEx valid before CLKOUT2 high
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after CLKOUT2 high
5
tosu(EAV-CKO2H)
Output setup time, EAx valid before CLKOUT2 high
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after CLKOUT2 high
9
tosu(CASV-CKO2H)
Output setup time, SDCAS/SSADS valid before
CLKOUT2 high
10
toh(CKO2H-CASV)
Output hold time, SDCAS/SSADS valid after CLKOUT2
high
11
tosu(EDV-CKO2H)
Output setup time, EDx valid before CLKOUT2 high§
12
toh(CKO2H-EDIV)
Output hold time, EDx invalid after CLKOUT2 high
13
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE valid before CLKOUT2
high
14
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE valid after CLKOUT2
high
15
tosu(SDA10V-CKO2H)
Output setup time, SDA10 valid before CLKOUT2 high
16
toh(CKO2H-SDA10IV)
Output hold time, SDA10 invalid after CLKOUT2 high
17
tosu(RASV-CKO2H)
Output setup time, SDRAS/SSOE valid before
CLKOUT2 high
18
toh(CKO2H-RASV)
Output hold time, SDRAS/SSOE valid after CLKOUT2
high
MAX
C6202-250
MIN
MAX
UNIT
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 1.5
ns
P − 3.5
P − 2.8
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
P−1
P − 0.9
ns
P − 3.5
P − 2.9
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
59
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
timing requirements for synchronous DRAM cycles for C6202B devices (see Figure 25)
C6202B-250
NO
NO.
MIN
MAX
C6202B-300
MIN
MAX
UNIT
7
tsu(EDV-CKO2H)
Setup time, read EDx valid before CLKOUT2 high
1.3
0
ns
8
th(CKO2H-EDV)
Hold time, read EDx valid after CLKOUT2 high
2.3
2.3
ns
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for C6202B devices†‡ (see Figure 25−Figure 30)
NO
NO.
PARAMETER
1
tosu(CEV-CKO2H)
Output setup time, CEx valid before CLKOUT2 high
2
toh(CKO2H-CEV)
Output hold time, CEx valid after CLKOUT2 high
3
tosu(BEV-CKO2H)
Output setup time, BEx valid before CLKOUT2 high
4
toh(CKO2H-BEIV)
Output hold time, BEx invalid after CLKOUT2 high
5
tosu(EAV-CKO2H)
Output setup time, EAx valid before CLKOUT2 high
6
toh(CKO2H-EAIV)
Output hold time, EAx invalid after CLKOUT2 high
9
tosu(CASV-CKO2H)
Output setup time, SDCAS/SSADS valid before
CLKOUT2 high
10
toh(CKO2H-CASV)
Output hold time, SDCAS/SSADS valid after CLKOUT2
high
11
tosu(EDV-CKO2H)
12
C6202B-250
C6202B-300
MIN
MIN
MAX
MAX
UNIT
P − 1.7
P−1
ns
P−3
P − 2.3
ns
P − 1.7
P−1
ns
P−3
P − 2.3
ns
P − 1.7
P−1
ns
P−3
P − 2.3
ns
P − 1.7
P−1
ns
P−3
P − 2.3
ns
Output setup time, EDx valid before CLKOUT2 high§
P − 2.3
P − 1.6
ns
toh(CKO2H-EDIV)
Output hold time, EDx invalid after CLKOUT2 high
P − 2.7
P−2
ns
13
tosu(WEV-CKO2H)
Output setup time, SDWE/SSWE valid before CLKOUT2
high
P − 1.7
P−1
ns
14
toh(CKO2H-WEV)
Output hold time, SDWE/SSWE valid after CLKOUT2
high
P−3
P − 2.3
ns
15
tosu(SDA10V-CKO2H)
Output setup time, SDA10 valid before CLKOUT2 high
P − 1.7
P−1
ns
16
toh(CKO2H-SDA10IV)
Output hold time, SDA10 invalid after CLKOUT2 high
P−3
P − 2.3
ns
17
tosu(RASV-CKO2H)
Output setup time, SDRAS/SSOE valid before
CLKOUT2 high
P − 1.7
P−1
ns
18
toh(CKO2H-RASV)
Output hold time, SDRAS/SSOE valid after CLKOUT2
high
P−3
P − 2.3
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
§ For the first write in a series of one or more consecutive adjacent writes, the write data is generated one CLKOUT2 cycle early to accommodate
the ED enable time.
‡
60
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
READ
READ
READ
CLKOUT2
1
2
CEx
3
BE[3:0]
5
EA[15:2]
4
BE1
BE2
CA2
CA3
BE3
6
CA1
7
8
D1
ED[31:0]
15
16
9
10
D2
D3
SDA10
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 25. Three SDRAM READ Commands
WRITE
WRITE
WRITE
CLKOUT2
1
2
CEx
3
BE[3:0]
4
BE1
5
EA[15:2]
ED[31:0]
BE2
BE3
CA2
CA3
D2
D3
6
CA1
11
D1
12
15
16
9
10
13
14
SDA10
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 26. Three SDRAM WRT Commands
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
61
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
ACTV
CLKOUT2
1
2
CEx
BE[3:0]
5
Bank Activate/Row Address
EA[15:2]
ED[31:0]
15
Row Address
SDA10
17
18
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 27. SDRAM ACTV Command
DCAB
CLKOUT2
1
2
15
16
17
18
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
SDRAS/SSOE†
SDCAS/SSADS†
13
14
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 28. SDRAM DCAB Command
62
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
REFR
CLKOUT2
1
2
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
17
18
SDRAS/SSOE†
9
10
SDCAS/SSADS†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 29. SDRAM REFR Command
MRS
CLKOUT2
1
2
5
6
CEx
BE[3:0]
EA[15:2]
MRS Value
ED[31:0]
SDA10
17
18
9
10
13
14
SDRAS/SSOE†
SDCAS/SSADS†
SDWE/SSWE†
†
SDCAS/SSADS, SDRAS/SSOE, and SDWE/SSWE operate as SDCAS, SDRAS, and SDWE, respectively, during SDRAM accesses.
Figure 30. SDRAM MRS Command
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
63
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
HOLD/HOLDA TIMING
timing requirements for the HOLD/HOLDA cycles† (see Figure 31)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
3
†
toh(HOLDAL-HOLDL)
Output hold time, HOLD low after HOLDA low
UNIT
MAX
P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles†‡
(see Figure 31)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
1
td(HOLDL-EMHZ)
Delay time, HOLD low to EMIF Bus high impedance
2
td(EMHZ-HOLDAL)
Delay time, EMIF Bus high impedance to HOLDA low
4
td(HOLDH-EMLZ)
Delay time, HOLD high to EMIF Bus low impedance
5
td(EMLZ-HOLDAH)
Delay time, EMIF Bus low impedance to HOLDA high
UNIT
MIN
MAX
3P
§
ns
0
2P
ns
3P
7P
ns
0
2P
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE, and SDA10.
§ All pending EMIF transactions are allowed to complete before HOLDA is asserted. The worst case for this is an asynchronous read or write with
external ARDY used or a minimum of eight consecutive SDRAM reads or writes when RBTR8 = 1. If no bus transactions are occurring, then the
minimum delay time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
‡
External Requestor
Owns Bus
DSP Owns Bus
DSP Owns Bus
3
HOLD
2
5
HOLDA
EMIF Bus†
†
1
4
C6202/02B
C6202/02B
EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE, and SDA10.
Figure 31. HOLD/HOLDA Timing
64
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
RESET TIMING
timing requirements for reset† (see Figure 32)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
1
tw(RST)
10
tsu(XD)
11
th(XD)
Width of the RESET pulse (PLL stable)‡
Width of the RESET pulse (PLL needs to sync
up)§
Setup time, XD configuration bits valid before RESET high¶
Hold time, XD configuration bits valid after RESET
high¶
UNIT
MAX
10P
ns
250
µs
5P
ns
5P
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡ This parameter applies to CLKMODE x1 when CLKIN is stable, and applies to CLKMODE x4 only when CLKIN and PLL are stable for C6202.
This parameter applies to CLKMODE x4, x6, x7, x8, x9, x10, and x11 when CLKIN and PLL are stable for C6202B GNY devices.
This parameter applies to CLKMODE x4, x6, x8, and x10 only when CLKIN and PLL are stable for C6202B GNZ devices.
§ This parameter applies to CLKMODE x4 only (it does not apply to CLKMODE x1) for C6202. This parameter applies to CLKMODE x4, x6, x7,
x8, x9, x10, and x11 only (it does not apply to CLKMODE x1) for C6202B GNY devices. This parameter applies to CLKMODE x4, x6, x8, and
x10 only (it does not apply to CLKMODE x1) for C6202B GNZ devices. The RESET signal is not connected internally to the clock PLL circuit.
The PLL, however, may need up to 250 µs to stabilize following device power up or after PLL configuration has been changed. During that time,
RESET must be asserted to ensure proper device operation. See the Clock PLL section for PLL lock times.
¶ XD[31:0] are the boot configuration pins during device reset.
switching characteristics over recommended operating conditions during reset†# (see Figure 32)
NO.
PARAMETER
C6202-200
C6202-250
C6202B-250
C6202B-300
MIN
2
td(RSTL-CKO2IV)
Delay time, RESET low to CLKOUT2 invalid
3
td(RSTH-CKO2V)
Delay time, RESET high to CLKOUT2 valid
4
td(RSTL-HIGHIV)
Delay time, RESET low to high group invalid
5
td(RSTH-HIGHV)
Delay time, RESET high to high group valid
6
td(RSTL-LOWIV)
Delay time, RESET low to low group invalid
7
td(RSTH-LOWV)
Delay time, RESET high to low group valid
8
td(RSTL-ZHZ)
Delay time, RESET low to Z group high impedance
9
td(RSTH-ZV)
Delay time, RESET high to Z group valid
UNIT
MAX
P
ns
4P
P
ns
ns
4P
P
ns
ns
4P
P
ns
ns
4P
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
# High group consists of:
XFCLK, HOLDA
Low group consists of:
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1
Z group consists of:
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE,
SDA10, CLKX0, CLKX1, CLKX2, FSX0, FSX1, FSX2, DX0, DX1, DX2, CLKR0, CLKR1, CLKR2, FSR0, FSR1,
FSR2, XCE[3:0], XBE[3:0]/XA[5:2], XOE, XRE, XWE/XWAIT, XAS, XW/R, XRDY, XBLAST, XHOLD,
and XHOLDA
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
65
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
RESET TIMING (CONTINUED)
CLKOUT1
1
10
RESET
11
2
3
4
5
6
7
8
9
CLKOUT2
GROUP†
HIGH
LOW GROUP†
Z
GROUP†
Boot Configuration
XD[31:0]‡
†
High group consists of:
Low group consists of:
Z group consists of:
XFCLK, HOLDA
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1.
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SDCAS/SSADS, SDRAS/SSOE, SDWE/SSWE,
SDA10, CLKX0, CLKX1, CLKX2, FSX0, FSX1, FSX2, DX0, DX1, DX2, CLKR0, CLKR1, CLKR2, FSR0, FSR1,
FSR2, XCE[3:0], XBE[3:0]/XA[5:2], XOE, XRE, XWE/XWAIT, XAS, XW/R, XRDY, XBLAST, XHOLD,
and XHOLDA.
‡ XD[31:0] are the boot configuration pins during device reset.
Figure 32. Reset Timing
66
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED MARCH 2004
EXTERNAL INTERRUPT TIMING
timing requirements for interrupt response cycles† (see Figure 33)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
†
UNIT
MAX
2
tw(ILOW)
Width of the interrupt pulse low
2P
ns
3
tw(IHIGH)
Width of the interrupt pulse high
2P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
switching characteristics over recommended operating conditions during interrupt response
cycles† (see Figure 33)
NO.
C6202-200
C6202-250
PARAMETER
MIN
†
C6202B-250
C6202B-300
MAX
MIN
9P
UNIT
MAX
1
tR(EINTH − IACKH)
Response time, EXT_INTx high to IACK high
4
td(CKO2L-IACKV)
Delay time, CLKOUT2 low to IACK valid
1
10
−1.5
9P
10
ns
ns
5
td(CKO2L-INUMV)
Delay time, CLKOUT2 low to INUMx valid
0
10
−2.0
10
ns
6
td(CKO2L-INUMIV)
Delay time, CLKOUT2 low to INUMx invalid
0
10
−2.0
10
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
1
CLKOUT2
2
3
EXT_INTx, NMI
Intr Flag
4
4
IACK
6
5
Interrupt Number
INUMx
Figure 33. Interrupt Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
67
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS FIFO TIMING
timing requirements for synchronous FIFO interface (see Figure 34, Figure 35, and Figure 36)
C6202-200
C6202-250
NO.
MIN
5
tsu(XDV-XFCKH)
Setup time, read XDx valid before XFCLK high
6
th(XFCKH-XDV)
Hold time, read XDx valid after XFCLK high
MAX
C6202B-250
C6202B-300
MIN
UNIT
MAX
3
3
ns
2.5
2.5
ns
switching characteristics over recommended operating conditions for synchronous FIFO
interface (see Figure 34, Figure 35, and Figure 36)
NO.
C6202-200
C6202-250
PARAMETER
C6202B-250
C6202B-300
MIN
MAX
MIN
MAX
1
td(XFCKH-XCEV)
Delay time, XFCLK high to XCEx valid
1.5
5.2
1.5
5.5
ns
2
td(XFCKH-XAV)
Delay time, XFCLK high to XBE[3:0]/XA[5:2] valid†
1.5
5.2
1.5
5.5
ns
3
td(XFCKH-XOEV)
Delay time, XFCLK high to XOE valid
1.5
5.2
1.5
5.5
ns
4
td(XFCKH-XREV)
Delay time, XFCLK high to XRE valid
1.5
5.2
1.5
5.5
ns
7
td(XFCKH-XWEV)
Delay time, XFCLK high to XWE/XWAIT‡ valid
1.5
5.2
1.5
5.5
ns
8
td(XFCKH-XDV)
Delay time, XFCLK high to XDx valid
6
ns
9
td(XFCKH-XDIV)
Delay time, XFCLK high to XDx invalid
5.2
1.5
1.5
ns
†
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
‡ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
XFCLK
1
1
XCE3†
2
XBE[3:0]/XA[5:2]‡
2
XA1
XA2
XA3
XA4
3
3
XOE
4
4
XRE
XWE/XWAIT§
6
5
XD[31:0]
D1
D2
D3
†
FIFO read (glueless) mode only available in XCE3.
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
§ XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
‡
Figure 34. FIFO Read Timing (Glueless Read Mode)
68
UNIT
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
D4
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS FIFO TIMING (CONTINUED)
XFCLK
1
1
XCEx
2
XBE[3:0]/XA[5:2]†
2
XA1
XA2
XA3
XA4
3
3
XOE
4
4
XRE
XWE/XWAIT‡
6
5
XD[31:0]
†
‡
D1
D2
D3
D4
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
Figure 35. FIFO Read Timing
XFCLK
1
1
XCEx
2
XBE[3:0]/XA[5:2]†
2
XA1
XA2
XA3
XA4
XOE
XRE
7
7
XWE/XWAIT‡
9
8
XD[31:0]
†
‡
D1
D2
D3
D4
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during synchronous FIFO accesses.
XWE/XWAIT operates as the write-enable signal XWE during synchronous FIFO accesses.
Figure 36. FIFO Write Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
69
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING
timing requirements for asynchronous peripheral cycles†‡§¶ (see Figure 37−Figure 40)
C6202-200
C6202-250
NO.
MIN
3
tsu(XDV-XREH)
Setup time, XDx valid before XRE
high
4
th(XREH-XDV)
6
C6202B-250
C6202B-300
MAX
MIN
UNIT
MAX
4.5
4.5
ns
Hold time, XDx valid after XRE
high
1
2.5
ns
tsu(XRDYH-XREL)
Setup time, XRDY high before
XRE low
−[(RST − 3) * P − 6]
−[(RST − 3) * P − 6]
ns
7
th(XREL-XRDYH)
Hold time, XRDY high after XRE
low
(RST − 3) * P + 2
(RST − 3) * P + 2
ns
9
tsu(XRDYL-XREL)
Setup time, XRDY low before XRE
low
−[(RST − 3) * P − 6]
−[(RST − 3) * P − 6]
ns
10
th(XREL-XRDYL)
Hold time, XRDY low after XRE
low
(RST − 3) * P + 2
(RST − 3) * P + 2
ns
11
tw(XRDYH)
Pulse width, XRDY high
2P
2P
ns
15
tsu(XRDYH-XWEL)
Setup time, XRDY high before
XWE low
−[(WST − 3) * P − 6]
−[(WST − 3) * P − 6]
ns
16
th(XWEL-XRDYH)
Hold time, XRDY high after XWE
low
(WST − 3) * P + 2
(WST − 3) * P + 2
ns
18
tsu(XRDYL-XWEL)
Setup time, XRDY low before
XWE low
−[(WST − 3) * P − 6]
−[(WST − 3) * P − 6]
ns
19
th(XWEL-XRDYL)
Hold time, XRDY low after XWE
low
(WST − 3) * P + 2
(WST − 3) * P + 2
ns
†
To ensure data setup time, simply program the strobe width wide enough. XRDY is internally synchronized. If XRDY does meet setup or hold
time, it may be recognized in the current cycle or the next cycle. Therefore, XRDY can be an asynchronous input.
‡ RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the XBUS XCE space control registers.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
¶ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use XRDY input to extend strobe width.
70
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
switching characteristics over recommended operating conditions for asynchronous peripheral
cycles †‡§¶ (see Figure 37−Figure 40)
NO.
C6202-200
C6202-250
PARAMETER
MIN
TYP
C6202B-250
C6202B-300
MAX
MIN
TYP
UNIT
MAX
1
tosu(SELV-XREL)
Output setup time, select
signals valid to XRE low
RS * P − 2
RS * P − 2
ns
2
toh(XREH-SELIV)
Output hold time, XRE low to
select signals invalid
RH * P − 2
RH * P − 2
ns
5
tw(XREL)
Pulse width, XRE low
8
td(XRDYH-XREH)
Delay time, XRDY high to
XRE high
3P
12
tosu(SELV-XWEL)
Output setup time, select
signals valid to XWE low
WS * P − 2
WS * P − 3
ns
13
toh(XWEH-SELIV)
Output hold time, XWE low to
select signals invalid
WH * P − 2
WH * P − 2
ns
14
tw(XWEL)
Pulse width, XWE low
17
td(XRDYH-XWEH)
Delay time, XRDY high to
XWE high
RST * P
RST * P
4P + 5
3P
WST * P
3P
ns
4P + 5
WST * P
4P + 5
3P
ns
ns
4P + 5
ns
†
RS = Read Setup, RST = Read Strobe, RH = Read Hold, WS = Write Setup, WST = Write Strobe, WH = Write Hold. These parameters are
programmed via the XBUS XCE space control registers.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
§ The sum of RS and RST (or WS and WST) must be a minimum of 4 in order to use XRDY input to extend strobe width.
¶ Select signals include: XCEx, XBE[3:0]/XA[5:2], XOE; and for writes, include XD[31:0], with the exception that XCEx can stay active for an
additional 7P ns following the end of the cycle.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
71
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
1
2
1
2
XCEx
XBE[3:0]/
XA[5:2]†
3
4
XD[31:0]
1
2
XOE
5
6
7
XRE
XWE/XWAIT‡
XRDY§
†
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
‡
Figure 37. Expansion Bus Asynchronous Peripheral Read Timing (XRDY Not Used)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
CLKOUT1
1
2
1
2
XCEx
XBE[3:0]/
XA[5:2]†
3
4
XD[31:0]
1
2
XOE
8
10
9
XRE
XWE/XWAIT‡
11
XRDY§
†
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
‡
Figure 38. Expansion Bus Asynchronous Peripheral Read Timing (XRDY Used)
72
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS PERIPHERAL TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
CLKOUT1
12
13
12
13
12
13
XCEx
XBE[3:0]/
XA[5:2]†
XD[31:0]
XOE
XRE
15
16
14
XWE/XWAIT‡
XRDY§
†
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
‡
Figure 39. Expansion Bus Asynchronous Peripheral Write Timing (XRDY Not Used)
Setup = 2 Strobe = 3
Not Ready
Hold = 2
CLKOUT1
12
13
12
13
12
13
XCEx
XBE[3:0]/
XA[5:2]†
XD[31:0]
XOE
XRE
17
18
19
XWE/XWAIT‡
11
XRDY§
†
XBE[3:0]/XA[5:2] operate as address signals XA[5:2] during expansion bus asynchronous peripheral accesses.
XWE/XWAIT operates as the write-enable signal XWE during expansion bus asynchronous peripheral accesses.
§ XRDY operates as active-high ready input during expansion bus asynchronous peripheral accesses.
‡
Figure 40. Expansion Bus Asynchronous Peripheral Write Timing (XRDY Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
73
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING
timing requirements with external device as bus master (see Figure 41 and Figure 42)
C6202-200
C6202-250
NO.
MIN
C6202B-250
C6202B-300
MAX
MIN
UNIT
MAX
1
tsu(XCSV-XCKIH)
Setup time, XCS valid before XCLKIN high
3.5
3.5
ns
2
th(XCKIH-XCS)
Hold time, XCS valid after XCLKIN high
2.8
2.8
ns
3
tsu(XAS-XCKIH)
Setup time, XAS valid before XCLKIN high
3.5
3.5
ns
4
th(XCKIH-XAS)
Hold time, XAS valid after XCLKIN high
2.8
2.8
ns
5
tsu(XCTL-XCKIH)
Setup time, XCNTL valid before XCLKIN high
3.5
3.5
ns
6
th(XCKIH-XCTL)
Hold time, XCNTL valid after XCLKIN high
2.8
2.8
ns
3.5
3.5
ns
2.8
2.8
ns
3.5
3.5
ns
2.8
2.8
ns
high†
7
tsu(XWR-XCKIH)
Setup time, XW/R valid before XCLKIN
8
th(XCKIH-XWR)
Hold time, XW/R valid after XCLKIN high†
high‡
9
tsu(XBLTV-XCKIH)
Setup time, XBLAST valid before XCLKIN
10
th(XCKIH-XBLTV)
Hold time, XBLAST valid after XCLKIN high‡
high§
16
tsu(XBEV-XCKIH)
Setup time, XBE[3:0]/XA[5:2] valid before XCLKIN
3.5
3.5
ns
17
th(XCKIH-XBEV)
Hold time, XBE[3:0]/XA[5:2] valid after XCLKIN high§
2.8
2.8
ns
18
tsu(XD-XCKIH)
Setup time, XDx valid before XCLKIN high
3.5
3.5
ns
19
th(XCKIH-XD)
Hold time, XDx valid after XCLKIN high
2.8
2.8
ns
†
XW/R input/output polarity selected at boot.
‡ XBLAST input polarity selected at boot
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
switching characteristics over recommended operating conditions with external device as bus
master¶ (see Figure 41 and Figure 42)
NO.
C6202-200
C6202-250
PARAMETER
MIN
UNIT
MAX
11
td(XCKIH-XDLZ)
Delay time, XCLKIN high to XDx low impedance
td(XCKIH-XDV)
Delay time, XCLKIN high to XDx valid
13
td(XCKIH-XDIV)
Delay time, XCLKIN high to XDx invalid
14
td(XCKIH-XDHZ)
Delay time, XCLKIN high to XDx high impedance
4P
ns
15
td(XCKIH-XRY)
Delay time, XCLKIN high to XRDY invalid#
5
16.5
3
4P − 0.5
ns
20
td(XCKIH-XRYLZ)
Delay time, XCLKIN high to XRDY low impedance
5
16.5
3
4P − 0.5
ns
2P + 5
3P + 16.5
2P + 3
7P + 0.5
ns
21
td(XCKIH-XRYHZ)
Delay time, XCLKIN high to XRDY high
0
MIN
12
5
impedance#
• HOUSTON, TEXAS 77251−1443
ns
4P − 0.5
3
4P
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
# XRDY operates as active-low ready input/output during host-port accesses.
POST OFFICE BOX 1443
0
16.5
¶
74
MAX
C6202B-250
C6202B-300
ns
ns
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
2
1
XCS
4
3
XAS
6
5
XCNTL
8
7
XW/R†
8
7
XW/R†
XBE[3:0]/XA[5:2]‡
10
9
XBLAST§
10
9
XBLAST§
13
14
12
11
D1
XD[31:0]
20
D2
15
D3
D4
15
21
XRDY¶
†
XW/R input/output polarity selected at boot
XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
§ XBLAST input polarity selected at boot
¶ XRDY operates as active-low ready input/output during host-port accesses.
‡
Figure 41. External Host as Bus Master—Read
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
75
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
2
1
XCS
4
3
XAS
6
5
XCNTL
8
7
XW/R†
8
7
XW/R†
17
16
XBE[3:0]/XA[5:2]‡
XBE1
XBE2
XBE3
XBE4
10
9
XBLAST§
10
9
XBLAST§
19
18
D1
XD[31:0]
20
D2
D3
15
XRDY¶
†
XW/R input/output polarity selected at boot
XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
§ XBLAST input polarity selected at boot
¶ XRDY operates as active-low ready input/output during host-port accesses.
‡
Figure 42. External Host as Bus Master—Write
76
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
D4
15
21
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
timing requirements with C62x as bus master (see Figure 43, Figure 44, and Figure 45)
C6202-200
C6202-250
NO.
MIN
†
MAX
C6202B-250
C6202B-300
MIN
UNIT
MAX
9
tsu(XDV-XCKIH)
Setup time, XDx valid before XCLKIN high
3.5
3.5
ns
10
th(XCKIH-XDV)
Hold time, XDx valid after XCLKIN high
2.8
2.8
ns
high†
11
tsu(XRY-XCKIH)
Setup time, XRDY valid before XCLKIN
3.5
3.5
ns
12
th(XCKIH-XRY)
Hold time, XRDY valid after XCLKIN high†
2.8
2.8
ns
14
tsu(XBFF-XCKIH)
Setup time, XBOFF valid before XCLKIN high
3.5
3.5
ns
15
th(XCKIH-XBFF)
Hold time, XBOFF valid after XCLKIN high
2.8
2.8
ns
XRDY operates as active-low ready input/output during host-port accesses.
switching characteristics over recommended operating conditions with C62x as bus master
(see Figure 43, Figure 44, and Figure 45)
NO.
1
PARAMETER
td(XCKIH-XASV)
Delay time, XCLKIN high to XAS valid
valid‡
C6202-200
C6202-250
C6202B-250
C6202B-300
MIN
MAX
MIN
5
16.5
3 4P − 0.5
ns
UNIT
MAX
2
td(XCKIH-XWRV)
Delay time, XCLKIN high to XW/R
5
16.5
3 4P − 0.5
ns
3
td(XCKIH-XBLTV)
Delay time, XCLKIN high to XBLAST valid§
5
16.5
3 4P − 0.5
ns
4
td(XCKIH-XBEV)
Delay time, XCLKIN high to XBE[3:0]/XA[5:2] valid¶
5
16.5
3 4P − 0.5
ns
5
td(XCKIH-XDLZ)
Delay time, XCLKIN high to XDx low impedance
0
0
ns
6
td(XCKIH-XDV)
Delay time, XCLKIN high to XDx valid
7
td(XCKIH-XDIV)
Delay time, XCLKIN high to XDx invalid
8
td(XCKIH-XDHZ)
Delay time, XCLKIN high to XDx high impedance
13
td(XCKIH-XWTV)
Delay time, XCLKIN high to XWE/XWAIT
16.5
5
valid#
5
4P − 0.5
3
ns
ns
4P
4P
ns
16.5
3 4P − 0.5
ns
‡
XW/R input/output polarity selected at boot.
§ XBLAST output polarity is always active low.
¶ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
# XWE/XWAIT operates as XWAIT output signal during host-port accesses.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
77
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
1
1
XAS
2
2
XW/R†
XW/R†
3
3
XBLAST‡
4
4
XBE[3:0]/XA[5:2]§
5
6
AD
XD[31:0]
7
BE
9
8
D1
10
D2
D3
D4
11
12
XRDY
13
13
XWE/XWAIT¶
†
XW/R input/output polarity selected at boot
XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ XWE/XWAIT operates as XWAIT output signal during host-port accesses.
‡
Figure 43. C62x as Bus Master—Read
XCLKIN
1
1
XAS
XW/R†
2
2
XW/R†
3
3
XBLAST‡
4
4
6
7
XBE[3:0]/XA[5:2]§
5
XD[31:0]
Addr
D1
D2
D3
D4
11
XRDY
13
XWE/XWAIT¶
†
XW/R input/output polarity selected at boot
XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ XWE/XWAIT operates as XWAIT output signal during host-port accesses.
‡
Figure 44. C62x as Bus Master—Write
78
12
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
13
8
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS SYNCHRONOUS HOST-PORT TIMING (CONTINUED)
XCLKIN
1
1
XAS
XW/R†
2
2
4
4
XW/R†
XBLAST‡
XBE[3:0]/XA[5:2]§
6
5
XD[31:0]
8
Addr
D1
11
7
D2
12
XRDY
15
14
XBOFF
XHOLD¶
XHOLDA¶
XHOLD#
XHOLDA#
†
XW/R input/output polarity selected at boot
XBLAST output polarity is always active low.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
¶ Internal arbiter enabled
# Internal arbiter disabled
|| This diagram illustrates XBOFF timing. Bus arbitration timing is shown in Figure 48 and Figure 49.
‡
Figure 45. C62x as Bus Master—BOFF Operation||
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
79
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS HOST-PORT TIMING
timing requirements with external device as asynchronous bus master† (see Figure 46 and
Figure 47)
C6202-200
C6202-250
NO.
MIN
C6202B-250
C6202B-300
MAX
MIN
UNIT
MAX
1
tw(XCSL)
Pulse duration, XCS low
4P
4P
ns
2
tw(XCSH)
Pulse duration, XCS high
4P
4P
ns
3
tsu(XSEL-XCSL)
Setup time, expansion bus select signals‡ valid before XCS
low
1
1
ns
4
th(XCSL-XSEL)
Hold time, expansion bus select signals‡ valid after XCS low
10
th(XRYL-XCSL)
Hold time, XCS low after XRDY low
11
tsu(XBEV-XCSH)
Setup time, XBE[3:0]/XA[5:2] valid before XCS high§
high§
3
3.4
ns
P + 1.5
P + 1.5
ns
1
1
ns
12
th(XCSH-XBEV)
Hold time, XBE[3:0]/XA[5:2] valid after XCS
3
3
ns
13
tsu(XDV-XCSH)
Setup time, XDx valid before XCS high
1
1
ns
14
th(XCSH-XDV)
Hold time, XDx valid after XCS high
3
3
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
Expansion bus select signals include XCNTL and XR/W.
§ XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
‡
switching characteristics over recommended operating conditions with external device as
asynchronous bus master† (see Figure 46 and Figure 47)
NO.
C6202-200
C6202-250
PARAMETER
MIN
†
MAX
5
td(XCSL-XDLZ)
Delay time, XCS low to XDx low impedance
0
6
td(XCSH-XDIV)
Delay time, XCS high to XDx invalid
0
7
td(XCSH-XDHZ)
Delay time, XCS high to XDx high impedance
8
td(XRYL-XDV)
Delay time, XRDY low to XDx valid
−4
1
9
td(XCSH-XRYH)
Delay time, XCS high to XRDY high
0
12
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
80
C6202B-250
C6202B-300
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
MIN
0
12
0
UNIT
MAX
ns
12
ns
4P
ns
−4
1.8
ns
−1
12
ns
4P
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
EXPANSION BUS ASYNCHRONOUS HOST-PORT TIMING (CONTINUED)
1
10
XCS
3
1
2
3
4
10
4
XCNTL
XBE[3:0]/XA[5:2]†
3
3
4
4
XR/W‡
3
3
4
4
XR/W‡
5
7
6
8
5
7
6
8
Word
XD[31:0]
9
9
XRDY
†
‡
XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
XW/R input/output polarity selected at boot
Figure 46. External Device as Asynchronous Master—Read
10
1
XCS
3
XBE[3:0]/XA[5:2]†
XR/W‡
XR/W‡
XD[31:0]
3
4
XCNTL
11
3
3
1
2
11
3
3
4
13
4
12
4
10
12
4
4
14
13
14
word
Word
9
9
XRDY
†
‡
XBE[3:0]/XA[5:2] operate as byte-enables XBE[3:0] during host-port accesses.
XW/R input/output polarity selected at boot
Figure 47. External Device as Asynchronous Master—Write
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
81
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
XHOLD/XHOLDA TIMING
timing requirements for expansion bus arbitration (internal arbiter enabled)† (see Figure 48)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
3
†
toh(XHDAH-XHDH)
Output hold time, XHOLD high after XHOLDA high
UNIT
MAX
P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
switching characteristics over recommended operating conditions for expansion bus arbitration
(internal arbiter enabled)†‡ (see Figure 48)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
1
td(XHDH-XBHZ)
Delay time, XHOLD high to XBus high impedance
2
td(XBHZ-XHDAH)
Delay time, XBus high impedance to XHOLDA high
4
td(XHDL-XHDAL)
Delay time, XHOLD low to XHOLDA low
5
td(XHDAL-XBLZ)
Delay time, XHOLDA low to XBus low impedance
MIN
MAX
3P
§
ns
0
2P
ns
3P
0
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
§ All pending XBus transactions are allowed to complete before XHOLDA is asserted.
‡
External Requestor
Owns Bus
DSP Owns Bus
DSP Owns Bus
3
XHOLD (input)
2
4
XHOLDA (output)
1
XBus†
†
5
C6202/02B
C6202/02B
XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
Figure 48. Expansion Bus Arbitration—Internal Arbiter Enabled
82
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
UNIT
ns
2P
ns
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
XHOLD/XHOLDA TIMING (CONTINUED)
switching characteristics over recommended operating conditions for expansion bus arbitration
(internal arbiter disabled)† (see Figure 49)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
1
2
td(XHDAH-XBLZ)
td(XBHZ-XHDL)
Delay time, XHOLDA high to XBus low impedance‡
Delay time, XBus high impedance to XHOLD
MAX
2P 2P + 10
low‡
0
UNIT
2P
ns
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡ XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
2
XHOLD (output)
XHOLDA (input)
1
C6202/02B
XBus†
†
XBus consists of XBE[3:0]/XA[5:2], XAS, XW/R, and XBLAST.
Figure 49. Expansion Bus Arbitration—Internal Arbiter Disabled
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
83
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING
timing requirements for McBSP†‡ (see Figure 50)
C6202-200
C6202-250
NO.
MIN
2
3
tc(CKRX)
tw(CKRX)
Cycle time, CLKR/X
Pulse duration, CLKR/X high or CLKR/X low
5
tsu(FRH-CKRL)
Setup time,
time external FSR high before CLKR low
6
th(CKRL-FRH)
Hold time,
time external FSR high after CLKR low
7
tsu(DRV-CKRL)
Setup time,
time DR valid before CLKR low
8
th(CKRL-DRV)
time DR valid after CLKR low
Hold time,
10
tsu(FXH-CKXL)
Setup time,
time external FSX high before CLKX low
11
th(CKXL-FXH)
Hold time,
time external FSX high after CLKX low
MAX
C6202B-250
C6202B-300
MIN
UNIT
MAX
CLKR/X ext
2P§
2P§
ns
CLKR/X ext
P −1¶
P −1¶
ns
CLKR int
9
9
CLKR ext
2
2
CLKR int
6
6
CLKR ext
3
3
CLKR int
8
8
CLKR ext
0.5
0.5
CLKR int
3
3
CLKR ext
4
4.5
CLKX int
9
9
CLKX ext
2
2
CLKX int
6
6
CLKX ext
3
4
†
ns
ns
ns
ns
ns
ns
CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
§ The maximum bit rate for the C6202/02B device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 250 MHz
(P = 4 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
¶ The minimum CLKR/X pulse duration is either (P −1) or 4 ns, whichever is larger. For example, when running parts at 250 MHz (P = 4 ns), use
4 ns as the minimum CLKR/X pulse duration. When running parts at 100 MHz (P = 10 ns), use (P −1) = 9 ns as the minimum CLKR/X pulse
duration.
‡
84
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP†‡ (see Figure 50)
NO.
C6202-200
C6202-250
PARAMETER
1
td(CKSH-CKRXH)
Delay time, CLKS high to CLKR/X high for
internal CLKR/X generated from CLKS input
2
tc(CKRX)
Cycle time, CLKR/X
C6202B-250
C6202B-300
UNIT
MIN
MAX
MIN
MAX
4
16
4
16
CLKR/X int
2P§¶
1#
C−
2P§¶
C+
ns
ns
1#
C − 1#
C + 1#
ns
ns
3
tw(CKRX)
Pulse duration, CLKR/X high or CLKR/X low
CLKR/X int
4
td(CKRH-FRV)
Delay time, CLKR high to internal FSR valid
CLKR int
−2
3
−2
3
9
td(CKXH-FXV)
Delay time,
time CLKX high to internal FSX valid
CLKX int
−2
3
−2
3
CLKX ext
3
9
2
9
12
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last
data bit from CLKX high
CLKX int
−1
5
−1
5
CLKX ext
2
9
2
9
13
td(CKXH-DXV)
time CLKX high to DX valid
Delay time,
CLKX int
−1
4
−0.5
3
CLKX ext
2
11
2
11
14
td(FXH-DXV)
Delay time, FSX high to DX valid ONLY applies
when in data delay 0 (XDATDLY = 00b) mode.
FSX int
−1
5
−1
5
FSX ext
0
10
0
10
ns
ns
ns
ns
†
CLKRP = CLKXP = FSRP = FSXP = 0. If the polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
Minimum delay times also represent minimum output hold times.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
¶ The maximum bit rate for the C6202/02B device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 250 MHz
(P = 4 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
# C = H or L
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
85
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKS
1
2
3
3
CLKR
4
FSR (int)
4
5
6
FSR (ext)
7
DR
2
3
8
Bit(n-1)
(n-2)
(n-3)
3
CLKX
9
FSX (int)
10
11
FSX (ext)
FSX (XDATDLY=00b)
12
DX
Bit 0
14
13
Bit(n-1)
13
(n-2)
Figure 50. McBSP Timings
86
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
(n-3)
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for FSR when GSYNC = 1 (see Figure 51)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
UNIT
MAX
1
tsu(FRH-CKSH)
Setup time, FSR high before CLKS high
4
ns
2
th(CKSH-FRH)
Hold time, FSR high after CLKS high
4
ns
CLKS
1
FSR external
2
CLKR/X (no need to resync)
CLKR/X (needs resync)
Figure 51. FSR Timing When GSYNC = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
87
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 52)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MASTER
MIN
†
‡
4
tsu(DRV-CKXL)
Setup time, DR valid before CLKX low
5
th(CKXL-DRV)
Hold time, DR valid after CLKX low
MAX
UNIT
SLAVE
MIN
MAX
12
2 − 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 52)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MASTER§
MIN
MAX
low¶
UNIT
SLAVE
MIN
MAX
1
th(CKXL-FXL)
Hold time, FSX low after CLKX
T−2
T+3
2
td(FXL-CKXH)
Delay time, FSX low to CLKX high#
L−2
L+3
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
−3
4
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX low
L−2
L+3
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
P+3
3P + 17
ns
8
td(FXL-DXV)
Delay time, FSX low to DX valid
2P + 2
4P + 17
ns
†
ns
ns
3P + 4
5P + 17
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
‡
88
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 52. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
89
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 53)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MASTER
MIN
†
‡
4
tsu(DRV-CKXH)
Setup time, DR valid before CLKX high
5
th(CKXH-DRV)
Hold time, DR valid after CLKX high
MAX
UNIT
SLAVE
MIN
MAX
12
2 − 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 53)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MASTER§
MIN
MAX
low¶
L−2
L+3
T−2
T+3
UNIT
SLAVE
MIN
MAX
1
th(CKXL-FXL)
Hold time, FSX low after CLKX
2
td(FXL-CKXH)
Delay time, FSX low to CLKX high#
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
−2
4
3P + 4
5P + 17
ns
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX low
−2
4
3P + 3
5P + 17
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
H−2
H+4
2P + 2
4P + 17
ns
†
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
The maximum transfer rate for SPI mode is limited to the above AC timing constraints.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
‡
90
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
6
Bit 0
7
FSX
DX
3
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 53. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
91
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 54)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MASTER
MIN
†
‡
4
tsu(DRV-CKXH)
Setup time, DR valid before CLKX high
5
th(CKXH-DRV)
Hold time, DR valid after CLKX high
MAX
UNIT
SLAVE
MIN
MAX
12
2 − 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 54)
NO
NO.
C6202-200
C6202-250
PARAMETER
MASTER§
MIN
MAX
C6202B-250
C6202B-300
SLAVE
MIN
MAX
MASTER§
MIN
MAX
SLAVE
MIN
UNIT
MAX
1
th(CKXH-FXL)
Hold time, FSX low after
CLKX high¶
T−2
T+3
T−2
T+3
ns
2
td(FXL-CKXL)
Delay time, FSX low to
CLKX low#
H−2
H+3
H−2
H+3
ns
3
td(CKXL-DXV)
Delay time, CLKX low to
DX valid
−2
4
−3
4
6
tdis(CKXH-DXHZ)
Disable time, DX high
impedance following last
data bit from CLKX high
H−2
H+3
H−2
H+3
7
tdis(FXH-DXHZ)
Disable time, DX high
impedance following last
data bit from FSX high
P+3
3P + 17
P+3
3P + 17
ns
8
td(FXL-DXV)
Delay time, FSX low to DX
valid
2P + 2
4P + 17
2P + 2
4P + 17
ns
3P + 4
5P + 17
†
3P + 4
5P + 17
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
The maximum transfer rate for SPI mode is limited to the above AC timing constraints.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
‡
92
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 54. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
93
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 55)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MASTER
MIN
†
‡
4
tsu(DRV-CKXL)
Setup time, DR valid before CLKX low
5
th(CKXL-DRV)
Hold time, DR valid after CLKX low
MAX
UNIT
SLAVE
MIN
MAX
12
2 − 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 55)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MASTER§
high¶
MIN
MAX
UNIT
SLAVE
MIN
MAX
1
th(CKXH-FXL)
Hold time, FSX low after CLKX
H−2
H+3
2
td(FXL-CKXL)
Delay time, FSX low to CLKX low#
T−2
T+2
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
−3
4
3P + 4
5P + 17
ns
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
−2
4
3P + 3
5P + 17
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
L−2
L+5
2P + 2
4P + 17
ns
†
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the 100-MHz limit.
¶ FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
# FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
‡
94
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 55. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
95
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
DMAC, TIMER, POWER-DOWN TIMING
switching characteristics over recommended operating conditions for DMAC outputs†
(see Figure 56)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
1
†
tw(DMACH)
Pulse duration, DMAC high
UNIT
MAX
2P −3
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
1
DMAC[3:0]
Figure 56. DMAC Timing
timing requirements for timer inputs† (see Figure 57)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
†
UNIT
MAX
1
tw(TINPH)
Pulse duration, TINP high
2P
ns
2
tw(TINPL)
Pulse duration, TINP low
2P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
switching characteristics over recommended operating conditions for timer outputs†
(see Figure 57)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
†
MAX
3
tw(TOUTH)
Pulse duration, TOUT high
2P −3
ns
4
tw(TOUTL)
Pulse duration, TOUT low
2P −3
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
2
1
TINPx
4
3
TOUTx
Figure 57. Timer Timing
96
UNIT
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
DMAC, TIMER, POWER-DOWN TIMING (CONTINUED)
switching characteristics over recommended operating conditions for power-down outputs†
(see Figure 58)
NO.
C6202-200
C6202-250
C6202B-250
C6202B-300
PARAMETER
MIN
1
†
tw(PDH)
Pulse duration, PD high
2P
UNIT
MAX
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
1
PD
Figure 58. Power-Down Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
97
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 59)
C6202-200
C6202-250
C6202B-250
C6202B-300
NO.
MIN
UNIT
MAX
1
tc(TCK)
Cycle time, TCK
35
ns
3
tsu(TDIV-TCKH)
Setup time, TDI/TMS/TRST valid before TCK high
11
ns
4
th(TCKH-TDIV)
Hold time, TDI/TMS/TRST valid after TCK high
9
ns
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 59)
NO.
2
C6202-200
C6202-250
PARAMETER
td(TCKL-TDOV)
Delay time, TCK low to TDO valid
C6202B-250
C6202B-300
MIN
MAX
MIN
MAX
−4.5
12
−4.5
13.5
1
TCK
2
2
TDO
3
TDI/TMS/TRST
Figure 59. JTAG Test-Port Timing
98
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
4
UNIT
ns
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MECHANICAL DATA
GJL (S-PBGA-N352) [C6202 only]
PLASTIC BALL GRID ARRAY
27,20
SQ
26,80
25,20
SQ
24,80
25,00 TYP
1,00
16,30 NOM
0,50
AB
Y
V
16,30 NOM
T
P
A1 Corner
M
K
H
F
D
B
AE
AC
AA
W
1,00
AD
U
R
N
L
0,50
AF
J
G
E
C
A
1
3
2
Heat Slug
5
4
7
6
9
8
11 13 15 17 19 21 23 25
10 12 14 16 18 20 22 24 26
Bottom View
See Note E
3,80 MAX
1,30
0,87
Seating Plane
0,70
0,50
NOTES: A.
B.
C.
D.
E.
F.
∅ 0,10 M
0,60
0,40
0,15
4173516-2/H 02/02
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Thermally enhanced plastic package with heat slug (HSL)
Flip chip application only
Possible protrusion in this area, but within 3,50 max package height specification
Falls within JEDEC MO-151/AAL-1
thermal resistance characteristics (S-PBGA package) [C6202 only]
NO
†
°C/W
Air Flow m/s†
1
RΘJC
Junction-to-case
0.47
N/A
2
RΘJA
Junction-to-free air
14.2
0.00
3
RΘJA
Junction-to-free air
12.3
0.50
4
RΘJA
Junction-to-free air
10.9
1.00
5
RΘJA
Junction-to-free air
9.3
2.00
m/s = meters per second
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
99
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MECHANICAL DATA
GLS (S-PBGA-N384)
PLASTIC BALL GRID ARRAY
18,10
SQ
17,90
16,80 TYP
0,80
0,40
V
T
P
M
A1 Corner
K
H
F
D
B
AA
W
U
0,80
Y
R
N
L
J
0,40
AB
G
E
C
A
1
2
3
4
5
6
7
Heat Slug
8
9
11 13 15 17 19 21
10 12 14 16 18 20 22
Bottom View
2,80 MAX
1,00 NOM
Seating Plane
0,55
0,45
0,10 M
0,45
0,35
0,12
4188959-3/E 11/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Thermally enhanced plastic package with heat slug (HSL)
Flip chip application only
thermal resistance characteristics (S-PBGA package) ) [C6202 only]
NO
†
°C/W
Air Flow m/s†
1
RΘJC
Junction-to-case
0.85
N/A
2
RΘJA
Junction-to-free air
21.6
0.00
3
RΘJA
Junction-to-free air
18.0
0.50
4
RΘJA
Junction-to-free air
15.5
1.00
5
RΘJA
Junction-to-free air
12.8
2.00
m/s = meters per second
100
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MECHANICAL DATA
GNZ (S−PBGA−N352) [C6202B only]
PLASTIC BALL GRID ARRAY
27,20
SQ
26,80
25,00 TYP
1,00
25,20
SQ
24,80
0,50
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
A1 Corner
1,00
0,50
1
2
3
4
5
6
7
8
9
11 13 15 17 19 21 23 25
10 12 14 16 18 20 22 24 26
Bottom View
2,80 MAX
0,50 NOM
Seating Plane
0,70
0,50
0,10 M
0,60
0,40
0,15
4202595-2/E 12/02
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Flip chip application only.
Substrate color may vary.
thermal resistance characteristics (S-PBGA package) [C6202B only]
NO
†
°C/W
Air Flow m/s†
1
RΘJC
Junction-to-case
6.35
N/A
2
RΘJA
Junction-to-free air
20.0
0.00
3
RΘJA
Junction-to-free air
17.0
0.50
4
RΘJA
Junction-to-free air
16.3
1.00
5
RΘJA
Junction-to-free air
15.2
2.00
m/s = meters per second
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
101
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
MECHANICAL DATA
GNY (S-PBGA-N384) [C6202B only]
PLASTIC BALL GRID ARRAY
18,10
SQ
17,90
16,80 TYP
0,80
0,40
V
T
P
M
A1 Corner
K
H
F
D
B
AA
W
U
0,80
Y
R
N
L
J
0,40
AB
G
E
C
A
1
2
3
4
5
6
7
8
9
11 13 15 17 19 21
10 12 14 16 18 20 22
Bottom View
2,35 MAX
Seating Plane
0,55
0,45
NOTES: A.
B.
C.
D.
∅ 0,10 M
0,45
0,35
0,12
4201137/C 11/01
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Flip chip application only
Substrate color may vary
thermal resistance characteristics (S-PBGA package) [C6202B only]
NO
†
(°C/W)
Air Flow m/s†
1
RΘJC
Junction-to-case
6.27
N/A
2
RΘJA
Junction-to-free air
17.6
0.0
3
RΘJA
Junction-to-free air
13.9
0.5
4
RΘJA
Junction-to-free air
13.1
1.0
5
RΘJA
Junction-to-free air
11.9
2.0
m/s = meters per second
102
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
TMS320C6202, TMS320C6202B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS104I − OCTOBER 1999 − REVISED FEBRUARY 2004
REVISION HISTORY
This data sheet revision history highlights the technical changes made to the SPRS104H device-specific data
sheet to make it an SPRS104I revision.
SCOPE: This document has been revised to add information pertaining to power-down mode logic.
PAGE(S)
NO.
ADDITIONS/CHANGES/DELETIONS
12
memory map summary:
Changed the document reference in the last sentence of the paragraph.
13
peripheral register descriptions:
Updated the information regarding the document reference.
18
DMA synchronization events:
Updated the information regarding the document reference.
19
Table 15, C6202/02B DSP Interrupts:
Changed the document reference in the second footnote to:
TMS320C6000 DSP Interrupt Selector Reference Guide (literature number SPRU646)
40
Figure 8, PWRD Field of the CSR Register:
Updated the PD1, PD2, and PD3 information that follows Figure 8.
50
switching characteristics over recommended operating conditions for CLKOUT2 table:
Removed NO. 1 (parameter tc(CKO2) ) from the table.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
103
PACKAGE OPTION ADDENDUM
www.ti.com
28-Jan-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TMS320C6202BGNY250
ACTIVE
FC/CSP
GNY
384
90
None
SNPB
Level-4-220C-72HR
TMS320C6202BGNY300
ACTIVE
FC/CSP
GNY
384
90
None
SNPB
Level-4-220C-72HR
TMS320C6202BGNYW25
OBSOLETE
FC/CSP
GNY
384
None
Call TI
Call TI
TMS320C6202BGNYW3
OBSOLETE
FC/CSP
GNY
384
None
Call TI
Call TI
TMS320C6202BGNZ250
ACTIVE
FCBGA
GNZ
352
40
None
SNPB
Level-4-220C-72HR
TMS320C6202BGNZ300
ACTIVE
FCBGA
GNZ
352
1
None
SNPB
Level-4-220C-72HR
TMS320C6202GJL200
NRND
FC/CSP
GJL
352
40
None
SNPB
Level-4-220C-72HR
TMS320C6202GJL250
NRND
FC/CSP
GJL
352
40
None
SNPB
Level-4-220C-72HR
TMS320C6202GJL250X
NRND
FC/CSP
GJL
352
40
None
SNPB
Level-4-220C-72HR
TMS320C6202GJLA200
NRND
FC/CSP
GJL
352
40
None
SNPB
Level-4-220C-72HR
TMS320C6202GJLA233
NRND
FC/CSP
GJL
352
1
None
SNPB
Level-4-220C-72HR
TMS320C6202GLS200
NRND
FC/CSP
GLS
384
90
None
SNPB
Level-4-220C-72HR
TMS320C6202GLS250
NRND
FC/CSP
GLS
384
1
None
SNPB
Level-4-220C-72HR
TMS320C6202GLS250X
NRND
FC/CSP
GLS
384
1
None
SNPB
Level-4-220C-72HR
TMS32C6202BGNZA250
ACTIVE
FCBGA
GNZ
352
90
None
SNPB
Level-4-220C-72HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated