TI SM320C6201GJCA20EP

SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
D Controlled Baseline
D
D
D
D
D
D
D
-- One Assembly/Test Site, One Fabrication
Site
Extended Temperature Performance of
--40°C to 105°C
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree†
High-Performance Fixed-Point Digital
Signal Processor (DSP) SM320C6201
-- 5-ns Instruction Cycle Time
-- 200-MHz Clock Rate
-- Eight 32-Bit Instructions/Cycle
-- 1600 MIPS
VelociTI™ Advanced Very Long Instruction
Word (VLIW) TMS320C62x™ DSP CPU Core
-- Eight Independent Functional Units:
-- Six Arithmetic Logic Units (ALUs)
(32-/40-Bit)
-- Two 16-Bit Multipliers (32-Bit Results)
-- Load-Store Architecture With 32 32-Bit
General-Purpose Registers
-- Instruction Packing Reduces Code Size
-- All Instructions Conditional
Instruction Set Features
-- Byte-Addressable (8-, 16-, 32-Bit Data)
-- 32-Bit Address Range
-- 8-Bit Overflow Protection
-- Saturation
-- Bit-Field Extract, Set, Clear
-- Bit-Counting
-- Normalization
D 1M-Bit On-Chip SRAM
D
D
D
D
D
D
D
D
D
D
-- 512K-Bit Internal Program/Cache
(16K 32-Bit Instructions)
-- 512K-Bit Dual-Access Internal Data
(64K Bytes) Organized as Two Blocks for
Improved Concurrency
32-Bit External Memory Interface (EMIF)
-- Glueless Interface to Asynchronous
Memories: SRAM and EPROM
-- Glueless Interface to Synchronous
Memories: SDRAM and SBSRAM
Four-Channel Bootloading
Direct-Memory-Access (DMA) Controller
with an Auxiliary Channel
16-Bit Host-Port Interface (HPI)
-- Access to Entire Memory Map
Two Multichannel Buffered Serial Ports
(McBSPs)
-- Direct Interface to T1/E1, MVIP, SCSA
Framers
-- ST-Bus-Switching Compatible
-- Up to 256 Channels Each
-- AC97-Compatible
-- Serial Peripheral Interface (SPI)
Compatible (Motorola™)
Two 32-Bit General-Purpose Timers
Flexible Phase-Locked Loop (PLL) Clock
Generator
IEEE-1149.1 (JTAG‡) Boundary-Scan
Compatible
352-Pin BGA Package (GJC Suffix)
CMOS Technology
-- 0.18-μm/5-Level Metal Process
3.3-V I/Os, 1.8-V Internal
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
VelociTI and TMS320C62x are trademarks of Texas Instruments.
Motorola is a trademark of Motorola, Inc.
†
Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range.
This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST,
electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this
component beyond specified performance and environmental limits.
‡ IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
Copyright © 2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
1
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
GJC/GJL
352-PIN BALL GRID ARRAY (BGA) PACKAGES
(BOTTOM VIEW)
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23 25
12 14 16 18 20 22 24 26
Table of Contents
GJC BGA package (bottom view) . . . . . . . . . . . . . . . . . . . . . . 2
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
functional and CPU (DSP core) block diagram . . . . . . . . . . . 4
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . . . . 5
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
documentation support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
absolute maximum ratings over operating case
temperature ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
recommended operating conditions . . . . . . . . . . . . . . . . . . . 26
electrical characteristics over recommended ranges of
supply voltage and operating case temperature . . . . 26
parameter measurement information . . . . . . . . . . . . . . .
input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . .
asynchronous memory timing . . . . . . . . . . . . . . . . . . . . .
synchronous-burst memory timing . . . . . . . . . . . . . . . . .
synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . .
HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . .
host-port interface timing . . . . . . . . . . . . . . . . . . . . . . . . .
multichannel buffered serial port timing . . . . . . . . . . . . .
DMAC, timer, power-down timing . . . . . . . . . . . . . . . . . .
JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
28
30
32
36
40
41
43
44
47
56
57
58
description
The TMS320C62x™ DSPs (including the SM320C6201-EP†) are the fixed-point DSP family in the
TMS320C6000™ DSP platform. The C6201 device is based on the high-performance, advanced VelociTI™
very-long-instruction-word (VLIW) architecture developed by Texas Instruments (TI), making these DSPs an
excellent choice for multichannel and multifunction applications. With performance of up to 1600 MIPS at a
clock rate of 200 MHz, the C6201 offers cost-effective solutions to high-performance DSP programming
challenges. The C6201 DSP possesses the operational flexibility of high-speed controllers and the numerical
capability of array processors. The processor has 32 general-purpose registers of 32-bit word length and eight
highly independent functional units. The eight functional units provide six arithmetic logic units (ALUs) for a high
degree of parallelism and two 16-bit multipliers for a 32-bit result. The C6201 can produce two
multiply-accumulates (MACs) per cycle—for a total of 466 million MACs per second (MMACS). The C62x™
DSP also has application-specific hardware logic, on-chip memory, and additional on-chip peripherals.
TMS320C6000, C6000, and C62x are trademarks of Texas Instruments.
Windows is a registered trademark of the Microsoft Corporation.
† The SM320C6201-EP device shall be referred to as C6201 throughout the remainder of this document.
2
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
description (continued)
The C6201 includes a large bank of on-chip memory and has a powerful and diverse set of peripherals. Program
memory consists of a 64K-byte block that is user-configurable as cache or memory-mapped program space.
Data memory of the C6201 consists of two 32K-byte blocks of RAM for improved concurrency. The peripheral
set includes two multichannel buffered serial ports (McBSPs), two general-purpose timers, a host-port interface
(HPI), and a glueless external memory interface (EMIF) capable of interfacing to SDRAM or SBSRAM and
asynchronous peripherals.
The C62x™ DSP has a complete set of development tools which includes: a new C compiler, an assembly
optimizer to simplify programming and scheduling, and a Windows™ debugger interface for visibility into source
code execution.
device characteristics
Table 1 provides an overview of the C6201 DSP. The table shows significant features of each device, including
the capacity of on-chip RAM, the peripherals, the execution time, and the package type with pin count.
Table 1. Characteristics of the C6201 Processor
HARDWARE FEATURES
Peripherals
On-Chip Memory
C6201 (FIXED-POINT DSP)
EMIF
1
DMA
1
HPI
1
McBSPs
2
32-Bit Timers
2
Size (Bytes)
72K
Organization
512-Kbit Program Memory
512-Kbit Data Memory (organized as two blocks)
CPU ID+Rev ID
Control Status Register (CSR.[31:16])
Frequency
MHz
Cycle Time
ns
Voltage
PLL Options
BGA Packages
0x0002
200
5 ns (C6201-200)
Core (V)
1.8
I/O (V)
3.3
CLKIN frequency multiplier
Bypass (x1), x4
27 x 27 mm
352-Pin BGA (GJL)
35 x 35 mm
352-Pin BGA (GJC)
Process Technology
μm
Product Status
Product Preview (PP)
Advance Information (AI)
Production Data (PD)
0.18 μm
Device Part Numbers
(For more details on the C6000™ DSP part
numbering, see Figure 4)
PD
SM320C6201GJCA20EP
C6000 is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
3
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
functional and CPU (DSP core) block diagram
C6201 Digital Signal Processors
SDRAM
SBSRAM
SRAM
Program
Access/Cache
Controller
32
External Memory
Interface (EMIF)
ROM/FLASH
Internal Program Memory
(64K Bytes)
I/O Devices
C62x CPU (DSP Core)
Timer 0
Instruction Fetch
Timer 1
Instruction Dispatch
.L1
DMA Bus
Synchronous
FIFOs
I/O Devices
HOST CONNECTION
Master /Slave
TI PCI2040
Power PC
683xx
960
4
32
Host Port
Interface
(HPI)
Data Path B
Data Path A
A Register File
Multichannel
Buffered Serial
Port 1
Interrupt
Selector
Control
Logic
Instruction Decode
Multichannel
Buffered Serial
Port 0
Framing Chips:
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
SPI Devices,
Codecs
Control
Registers
.S1 .M1 .D1
Test
B Register File
.D2 .M2
.S2
In-Circuit
Emulation
.L2
Interrupt
Control
Peripheral Control Bus
Direct Memory
Access Controller
(DMA)
(4 Channels)
PLL
(x1, x4)
POST OFFICE BOX 1443
Data
Access
Controller
PowerDown
Logic
Internal Data
Memory
(64K Bytes)
Boot Configuration
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
CPU (DSP core) description
The CPU fetches VelociTI™ advanced very-long instruction words (VLIW) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI™ VLIW architecture
features controls by which all eight units do not have to be supplied with instructions if they are not ready to
execute. The first bit of every 32-bit instruction determines if the next instruction belongs to the same execute
packet as the previous instruction, or whether it should be executed in the following clock as a part of the next
execute packet. Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The
variable-length execute packets are a key memory-saving feature, distinguishing the C62x CPU from other
VLIW architectures.
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 16 32-bit registers for a total of 32 general-purpose registers. The two sets of functional units, along
with two register files, compose sides A and B of the CPU [see functional and CPU (DSP core) block diagram
and Figure 1]. The four functional units on each side of the CPU can freely share the 16 registers belonging to
that side. Additionally, each side features a single data bus connected to all the registers on the other side, by
which the two sets of functional units can access data from the register files on the opposite side. While register
access by functional units on the same side of the CPU as the register file can service all the units in a single
clock cycle, register access using the register file across the CPU supports one read and one write per cycle.
Another key feature of the C62x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C62x CPU supports a variety of indirect addressing modes using either linear- or circular-addressing modes
with 5- or 15-bit offsets. All instructions are conditional, and most can access any one of the 32 registers. Some
registers, however, are singled out to support specific addressing or to hold the condition for conditional
instructions (if the condition is not automatically “true”). The two .M functional units are dedicated for multiplies.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. If an execute packet crosses the fetch
packet boundary (256 bits wide), the assembler places it in the next fetch packet, while the remainder of the
current fetch packet is padded with NOP instructions. The number of execute packets within a fetch packet can
vary from one to eight. Execute packets are dispatched to their respective functional units at the rate of one per
clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from the current fetch
packet have been dispatched. After decoding, the instructions simultaneously drive all active functional units
for a maximum execution rate of eight instructions every clock cycle. While most results are stored in 32-bit
registers, they can be subsequently moved to memory as bytes or half-words as well. All load and store
instructions are byte-, half-word, or word-addressable.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
5
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
CPU (DSP core) description (continued)
src1
.L1
src2
dst
long dst
long src
ST1
long src
long dst
dst
.S1
src1
Data Path A
8
8
32
8
Register
File A
(A0--A15)
src2
.M1
dst
src1
src2
LD1
DA1
.D1
dst
src1
src2
2X
1X
DA2
.D2
src2
src1
dst
LD2
src2
.M2
src1
dst
src2
Data Path B
src1
dst
long dst
long src
Register
File B
(B0--B15)
.S2
ST2
long src
long dst
dst
.L2
src2
8
32
8
8
src1
Control
Register
File
Figure 1. TMS320C62x CPU (DSP Core) Data Paths
6
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
signal groups description
CLKIN
CLKOUT2
CLKOUT1
CLKMODE1
CLKMODE0
PLLFREQ3
PLLFREQ2
PLLFREQ1
PLLV
PLLG
PLLF
Boot Mode
BOOTMODE4
BOOTMODE3
BOOTMODE2
BOOTMODE1
BOOTMODE0
Reset and
Interrupts
RESET
NMI
EXT_INT7
EXT_INT6
EXT_INT5
EXT_INT4
IACK
INUM3
INUM2
INUM1
INUM0
Little ENDIAN
Big ENDIAN
LENDIAN
Clock/PLL
TMS
TDO
TDI
TCK
TRST
EMU1
EMU0
JTAG
Emulation
RSV9
RSV8
RSV7
RSV6
RSV5
RSV4
RSV3
RSV2
RSV1
RSV0
DMA Status
DMAC3
DMAC2
DMAC1
DMAC0
Power-Down
Status
PD
Reserved
Control/Status
HD[15:0]
HCNTL0
HCNTL1
16
Data
HPI
(Host-Port Interface)
Register Select
Control
HHWIL
HBE1
HBE0
Half-Word/Byte
Select
HAS
HR/W
HCS
HDS1
HDS2
HRDY
HINT
Figure 2. CPU (DSP Core) and Peripheral Signals
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
7
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
signal groups description (continued)
ED[31:0]
32
CE3
CE2
CE1
CE0
EA[21:2]
BE3
BE2
BE1
BE0
HOLD
HOLDA
Data
Asynchronous
Memory
Control
Memory Map
Space Select
20
Word Address
ARE
AOE
AWE
ARDY
SBSRAM
Control
SSADS
SSOE
SSWE
SSCLK
SDRAM
Control
SDA10
SDRAS
SDCAS
SDWE
SDCLK
Byte Enables
HOLD/
HOLDA
EMIF
(External Memory Interface)
TOUT1
TINP1
Timer 1
Timer 0
TOUT0
TINP0
Timers
McBSP1
McBSP0
CLKX1
FSX1
DX1
Transmit
Transmit
CLKX0
FSX0
DX0
CLKR1
FSR1
DR1
Receive
Receive
CLKR0
FSR0
DR0
CLKS1
Clock
Clock
CLKS0
McBSPs
(Multichannel Buffered Serial Ports)
Figure 3. Peripheral Signals
8
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
CLOCK/PLL
CLKIN
C10
I
Clock Input
CLKOUT1
AF22
O
Clock output at full device speed
CLKOUT2
AF20
O
Clock output at half of device speed
I
Clock mode selects
• Selects whether the CPU clock frequency = input clock frequency x4 or x1
For more details on the GJC and GJL CLKMODE pins and the PLL multiply factors,
see the Clock PLL section of this data sheet.
I
PLL frequency range (3, 2, and 1)
• The target range for CLKOUT1 frequency is determined by the 3
3-bit
bit value of the
PLLFREQ pins.
CLKMODE1
C6
CLKMODE0
C5
PLLFREQ3
A9
PLLFREQ2
D11
PLLFREQ1
B10
PLLV‡
D12
A§
PLL analog VCC connection for the low-pass filter
PLLG‡
C12
A§
PLL analog GND connection for the low-pass filter
PLLF
A11
A§
PLL low-pass filter connection to external components and a bypass capacitor
TMS
L3
I
TDO
W2
O/Z
TDI
R4
I
JTAG test port data in (features an internal pullup)
TCK
R3
I
JTAG test port clock
TRST
T1
I
JTAG test port reset (features an internal pulldown)
EMU1
Y1
I/O/Z
Emulation pin 1, pullup with a dedicated 20-kΩ resistor¶
EMU0
W3
I/O/Z
Emulation pin 0, pullup with a dedicated 20-kΩ resistor¶
RESET
K2
I
Device reset
NMI
L2
I
Nonmaskable interrupt
• Edge-driven (rising edge)
EXT_INT7
U3
EXT_INT6
V2
EXT_INT5
W1
I
EXT_INT4
U4
External interrupts
• Edge-driven
• Polarityy independently
p
y selected via the external interrupt
p polarity
p
y register
g
bits
(EXTPOL [3 0])
(EXTPOL.[3:0])
IACK
Y2
O
Interrupt acknowledge for all active interrupts serviced by the CPU
O
Active interrupt identification number
• Valid during IACK for all active interrupts (not just external)
• Encoding order follows the interrupt-service fetch-packet ordering
JTAG EMULATION
JTAG test port mode select (features an internal pullup)
JTAG test port data out
RESET AND INTERRUPTS
INUM3
AA1
INUM2
W4
INUM1
AA2
INUM0
AB1
LITTLE ENDIAN/BIG ENDIAN
LENDIAN
H3
I
If high, LENDIAN selects little-endian byte/half-word addressing order within a word
If low, LENDIAN selects big-endian addressing
PD
D3
O
Power-down mode 2 or 3 (active if high)
POWER-DOWN STATUS
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
PLLV and PLLG are not part of external voltage supply or ground. See the clock PLL section for information on how to connect these pins.
§ A = Analog Signal (PLL Filter)
¶ For emulation and normal operation, pull up EMU1 and EMU0 with a dedicated 20-kΩ resistor. For boundary scan, pull down EMU1 and EMU0
with a dedicated 20-kΩ resistor.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
9
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
HOST-PORT INTERFACE (HPI)
HINT
H26
O
Host interrupt (from DSP to host)
HCNTL1
F23
I
Host control -- selects between control, address, or data registers
HCNTL0
D25
I
Host control -- selects between control, address, or data registers
HHWIL
C26
I
Host half-word select -- first or second half-word (not necessarily high or low order)
HBE1
E23
I
Host byte select within word or half-word
HBE0
D24
I
Host byte select within word or half-word
HR/W
C23
I
Host read or write select
HD15
B13
HD14
B14
HD13
C14
HD12
B15
HD11
D15
HD10
B16
HD9
A17
HD8
B17
HD7
D16
HD6
B18
HD5
A19
HD4
C18
HD3
B19
HD2
C19
HD1
B20
I/O/Z
Host port data ((used
Host-port
sed for transfer of data,
data address
address, and control)
HD0
B21
HAS
C22
I
Host address strobe
HCS
B23
I
Host chip select
HDS1
D22
I
Host data strobe 1
HDS2
A24
I
Host data strobe 2
HRDY
J24
O
Host ready (from DSP to host)
BOOTMODE4
D8
BOOTMODE3
B4
BOOT MODE
†
BOOTMODE2
A3
BOOTMODE1
D5
BOOTMODE0
C4
I
Boot mode
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
10
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
EMIF -- CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY
CE3
AE22
CE2
AD26
CE1
AB24
CE0
AC26
BE3
AB25
BE2
AA24
BE1
Y23
BE0
AA26
O/Z
Memory space enables
• Enabled by bits 24 and 25 of the word address
• Only one asserted during any external data access
O/Z
Byte-enable control
• Decoded from the two lowest bits of the internal address
• Byte-write
y
enables for most types
yp of memoryy
• Can
C b
be di
directly
tl connected
t d to
t SDRAM read
d and
d write
it maskk signal
i
l (SDQM)
EMIF -- ADDRESS
†
EA21
J26
EA20
K25
EA19
L24
EA18
K26
EA17
M26
EA16
M25
EA15
P25
EA14
P24
EA13
R25
EA12
T26
EA11
R23
EA10
U26
EA9
U25
EA8
T23
EA7
V26
EA6
V25
EA5
W26
EA4
V24
EA3
W25
EA2
Y26
O/Z
External address (word address)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
11
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
EMIF -- DATA
ED31
AB2
ED30
AC1
ED29
AA4
ED28
AD1
ED27
AC3
ED26
AD4
ED25
AF3
ED24
AE4
ED23
AD5
ED22
AF4
ED21
AE5
ED20
AD6
ED19
AE6
ED18
AD7
ED17
AC8
ED16
AF7
ED15
AD9
ED14
AD10
ED13
AF9
ED12
AC11
ED11
AE10
ED10
AE11
ED9
AF11
ED8
AE14
ED7
AF15
ED6
AE15
I/O/Z
External data
ED5
AF16
ED4
AC15
ED3
AE17
ED2
AF18
ED1
AF19
ED0
AC17
ARE
Y24
O/Z
Asynchronous memory read enable
AOE
AC24
O/Z
Asynchronous memory output enable
AWE
AD23
O/Z
Asynchronous memory write enable
ARDY
W23
I
Asynchronous memory ready input
EMIF -- ASYNCHRONOUS MEMORY CONTROL
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
12
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
EMIF -- SYNCHRONOUS BURST SRAM (SBSRAM) CONTROL
SSADS
AC20
O/Z
SBSRAM address strobe
SSOE
AF21
O/Z
SBSRAM output enable
SSWE
AD19
O/Z
SBSRAM write enable
SSCLK
AD17
O
SBSRAM clock
EMIF -- SYNCHRONOUS DRAM (SDRAM) CONTROL
SDA10
AD21
O/Z
SDRAM address 10 (separate for deactivate command)
SDRAS
AF24
O/Z
SDRAM row-address strobe
SDCAS
AD22
O/Z
SDRAM column-address strobe
SDWE
AF23
O/Z
SDRAM write enable
SDCLK
AE20
O
SDRAM clock
EMIF -- BUS ARBITRATION
HOLD
AA25
I
Hold request from the host
HOLDA
A7
O
Hold-request acknowledge to the host
TOUT1
H24
O
Timer 1 or general-purpose output
TINP1
K24
I
Timer 1 or general-purpose input
TOUT0
M4
O
Timer 0 or general-purpose output
TINP0
K4
I
Timer 0 or general-purpose input
DMAC3
D2
TIMER1
TIMER0
DMA ACTION COMPLETE STATUS
DMAC2
F4
DMAC1
D1
DMAC0
E2
CLKS1
E25
I
CLKR1
H23
I/O/Z
Receive clock
CLKX1
F26
I/O/Z
Transmit clock
DR1
D26
I
Receive data
DX1
G23
O/Z
Transmit data
FSR1
E26
I/O/Z
Receive frame sync
FSX1
F25
I/O/Z
Transmit frame sync
O
DMA action complete
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
†
External clock source (as opposed to internal)
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
13
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
CLKS0
L4
I
CLKR0
M2
I/O/Z
External clock source (as opposed to internal)
Receive clock
CLKX0
L1
I/O/Z
Transmit clock
DR0
J1
I
Receive data
DX0
R1
O/Z
Transmit data
FSR0
P4
I/O/Z
Receive frame sync
FSX0
P3
I/O/Z
Transmit frame sync
RESERVED FOR TEST
RSV0
T2
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV1
G2
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV2
C11
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV3
B9
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV4
A6
I
Reserved for testing, pulldown with a dedicated 20-kΩ resistor
RSV5
C8
O
Reserved (leave unconnected, do not connect to power or ground)
RSV6
C21
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV7
B22
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV8
A23
I
Reserved for testing, pullup with a dedicated 20-kΩ resistor
RSV9
E4
O
Reserved (leave unconnected, do not connect to power or ground)
UNCONNECTED PINS
A8
B8
C9
D10
D21
NC
G1
Unconnected pins
H1
H2
J2
K3
R2
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
14
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
3.3-V SUPPLY VOLTAGE PINS
A10
A15
A18
A21
A22
B7
C1
D17
F3
G24
G25
H25
J25
L25
M3
N3
N23
R26
T24
DVDD
U24
W24
S
3 3 V supply voltage
3.3-V
Y4
AB3
AB4
AB26
AC6
AC10
AC19
AC21
AC22
AC25
AD11
AD13
AD15
AD18
AE18
AE21
AF5
AF6
AF17
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
15
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
1.8-V SUPPLY VOLTAGE PINS
A5
A12
A16
A20
B2
B6
B11
B12
B25
C3
C15
C20
C24
D4
D6
D7
D9
D14
CVDD
D18
D20
S
1 8 V supply voltage
1.8-V
D23
E1
F1
H4
J4
J23
K1
K23
M1
M24
N4
N25
P2
P23
T3
T4
U1
V4
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
16
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
1.8-V SUPPLY VOLTAGE PINS (CONTINUED)
V23
AC4
AC9
AC12
AC13
AC18
AC23
AD3
CVDD
AD8
AD14
S
1 8 V supply voltage
1.8-V
AD24
AE2
AE8
AE12
AE25
AF12
--GROUND PINS
A1
A2
A4
A13
A14
A25
A26
B1
B3
VSS
B5
GND
Ground pins
B24
B26
C2
C7
C13
C16
C17
C25
D13
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
17
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
GROUND PINS (CONTINUED)
D19
E3
E24
F2
F24
G3
G4
G26
J3
L23
L26
M23
N1
N2
N24
N26
P1
P26
VSS
R24
T25
GND
Ground pins
U2
U23
V1
V3
Y3
Y25
AA3
AA23
AB23
AC2
AC5
AC7
AC14
AC16
AD2
AD12
AD16
AD20
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
18
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
Signal Descriptions (Continued)
SIGNAL
NAME
PIN NO.
GJC
TYPE†
DESCRIPTION
GROUND PINS (CONTINUED)
AD25
AE1
AE3
AE7
AE9
AE13
AE16
AE19
AE23
VSS
AE24
GND
Ground pins
AE26
AF1
AF2
AF8
AF10
AF13
AF14
AF25
AF26
†
I = Input, O = Output, Z = High Impedance, S = Supply Voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
19
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
development support
TI offers an extensive line of development tools for the TMS320C6000™ DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules.
The following products support development of C6000™ DSP-based applications:
Software Development Tools:
Code Composer Studio™ Integrated Development Environment (IDE) including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS™) Emulator (supports C6000™ DSP multiprocessor system debug)
EVM (Evaluation Module)
The TMS320 DSP Development Support Reference Guide (SPRU011) contains information about
development-support products for all TMS320™ DSP family member devices, including documentation. See
this document for further information on TMS320™ DSP documentation or any TMS320™ DSP support products
from Texas Instruments. An additional document, the TMS320 Third-Party Support Reference Guide
(SPRU052), contains information about TMS320™ DSP-related products from other companies in the industry.
To receive TMS320™ DSP literature, contact the Literature Response Center at 800/477-8924.
For a complete listing of development-support tools for the TMS320C6000™ DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL) and under
“Development Tools”, select “Digital Signal Processors”. For information on pricing and availability, contact the
nearest TI field sales office or authorized distributor.
Code Composer Studio, XDS, and TMS320 are trademarks of Texas Instruments.
20
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
device and development support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
TMS320™ DSP family devices and support tools. Each TMS320™ DSP member has one of three prefixes: TMX,
TMP, or TMS, and each SMJ320™ DSP member has one of three prefixes: SMX, SM, or SMJ. Texas Instruments
recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes
represent evolutionary stages of product development from engineering prototypes (TMX/TMDX) through fully
qualified production devices/tools (TMS/TMDS). This development flow is defined below.
Device development evolutionary flow:
SMX
Experimental device that is not necessarily representative of the final device’s electrical
specifications
TMP
Final silicon die that conforms to the device’s electrical specifications but has not completed
quality and reliability verification
SM/SMJ
Fully-qualified production device
Support tool development evolutionary flow:
TMDX
Development support product that has not yet completed Texas Instruments internal qualification
testing.
TMDS
Fully qualified development support product
TMX and TMP devices and TMDX development support tools are shipped against the following disclaimer:
“Developmental product is intended for internal evaluation purposes.”
TMS as well as SM/SMJ devices and TMDS development support tools have been characterized fully, and the
quality and reliability of the device has been demonstrated fully. TI’s standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GNM) and temperature range (for example, M). Figure 4 provides a legend for reading the
complete device name for many TMS320™ DSP family members.
TMS320 is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
21
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
device and development-support tool nomenclature (continued)
SM 320 C
PREFIX
SMX =
TMP =
TMS =
SMJ =
SMQ=
SM =
6201 GJC
A
20
EP
experimental device
prototype device
qualified device
MIL-PRF-38535 (QML)
QML Plastic device
commercial processing
ENHANCED PLASTIC
SPEED
20 = 200 MHz
DEVICE FAMILY
320 = TMS320 Family
TEMPERATURE RANGE
A = Extended temperature (--40°C to 105°C)
M = Military
TECHNOLOGY
C = CMOS
LC = Low-Voltage CMOS (3.3 V)
VC = Low-Voltage CMOS [3.3 V (2.5 V
or 1.8 V core)]
PACKAGE TYPE†
GJC = 352-pin plastic BGA
GJL = 352-pin plastic BGA
GFN = 256-pin plastic BGA
DEVICE
6000 DSP:
6201 6203
6701 6711
NOTE: Not all speed, package, process, and temperature combinations are available.
†
BGA = Ball Grid Array
Figure 4. TMS320C6000™ Device Nomenclature (Including SM320C6201-EP)
MicroStar BGA is a trademark of Texas Instruments.
22
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
documentation support
Extensive documentation supports all TMS320™ DSP family devices from product announcement through
applications development. The types of documentation available include: data sheets, such as this document,
with design specifications; complete user’s reference guides for all devices and tools; technical briefs;
development-support tools; on-line help; and hardware and software applications. The following is a brief,
descriptive list of support documentation specific to the C6000™ DSP devices:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 CPU (DSP core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 Peripherals Reference Guide (literature number SPRU190) describes the functionality of
the peripherals available on the C6000™ DSP platform of devices, such as the 64-/32-/16-bit external memory
interfaces (EMIFs), 32-/16-bit host-port interfaces (HPIs), multichannel buffered serial ports (McBSPs), direct
memory access (DMA), enhanced direct-memory-access (EDMA) controller, expansion bus (XB), peripheral
component interconnect (PCI), clocking and phase-locked loop (PLL); and power-down modes. This guide also
includes information on internal data and program memories.
The TMS320C6000 Technical Brief (literature number SPRU197) gives an introduction to the C62x™/C67x™
devices, associated development tools, and third-party support.
The tools support documentation is electronically available within the Code Composer Studio™ IDE. For a
complete listing of the latest C6000™ DSP documentation, visit the Texas Instruments web site on the
Worldwide Web at http://www.ti.com uniform resource locator (URL).
C67x is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
23
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
clock PLL
All of the C62x™ clocks are generated from a single source through the CLKIN pin. This source clock either
drives the PLL, which generates the internal CPU clock, or bypasses the PLL to become the CPU clock.
To use the PLL to generate the CPU clock, the filter circuit shown in Figure 5 must be properly designed. Note
that for C6201, the EMI filter must be powered by the I/O voltage (3.3 V).
To configure the C62x™ PLL clock for proper operation, see Figure 5 and Table 2. To minimize the clock jitter,
a single clean power supply should power both the C62x™ DSP device and the external clock oscillator circuit.
The minimum CLKIN rise and fall times should also be observed. See the input and output clocks section for
input clock timing requirements.
PLLF
C3
10 μF
C4
0.1 μF
R1
CLKOUT1 Frequency Range 65--200 MHz
0 0 0
CLKOUT1 Frequency Range 50--140 MHz
C6201
EMIF
CLKOUT1
2
(Bypass)
0 0 1
C1
C2
PLLG
GND
CLKIN
CLKOUT
CLKMODE0
CLKMODE1
EMI Filter
1 IN
PLLV
CLKOUT1 Frequency Range 130--233 MHz
PLLFREQ3
PLLFREQ2
PLLFREQ1
3 OUT
3.3 V
0 1 0
1 1 -- MULT×4
CLKOUT2
SSCLK
SDCLK
f(CLKOUT)=f(CLKIN)×4
0 1 -- Reserved
1 0 -- Reserved
0 0 -- MULT×1
f(CLKOUT)=f(CLKIN)
NOTES: A. Keep the lead length and the number of vias between pin PLLF, pin PLLG, R1, C1, and C2 to a minimum. In addition, place all PLL
components (R1, C1, C2, C3, C4, and EMI Filter) as close to the C6000™ DSP device as possible. Best performance is achieved
with the PLL components on a single side of the board without jumpers, switches, or components other than the ones shown. For
CLKMODE x4, values for C1, C2, and R1 are fixed and apply to all valid frequency ranges of CLKIN and CLKOUT.
B. For CLKMODE x1, the PLL is bypassed and all six external PLL components can be removed. For this case, the PLLV terminal has
to be connected to a clean supply and the PLLG and PLLF terminals should be tied together.
C. Due to overlap of frequency ranges when choosing the PLLFREQ, more than one frequency range can contain the CLKOUT1
frequency. Choose the lowest frequency range that includes the desired frequency. For example, for CLKOUT1 = 133 MHz, a
PLLFREQ value of 000b should be used. For CLKOUT1 = 200 MHz, PLLFREQ should be set to 001b. PLLFREQ values other than
000b, 001b, and 010b are reserved.
D. The 3.3-V supply for the EMI filter (and PLLV) must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
E. EMI filter manufacturer TDK part number ACF451832-153-T
Figure 5. PLL Block Diagram
24
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
clock PLL (continued)
Table 2. PLL Component Selection Table
†
CLKMODE
CLKIN
RANGE
(MHz)
CPU CLOCK
FREQUENCY
(CLKOUT1)
RANGE (MHz)
CLKOUT2
RANGE
(MHz)
R1
(Ω)
C1
(nF)
C2
(pF)
TYPICAL
LOCK TIME
(μs)†
x4
12.5--50
50--200
25--100
60.4
27
560
75
Under some operating conditions, the maximum PLL lock time may vary as much as 150% from the specified typical value. For example, if the
typical lock time is specified as 100 μs, the maximum value may be as long as 250 μs.
power-supply sequencing
TI DSPs do not require specific power sequencing between the core supply and the I/O supply. However,
systems should be designed to ensure that neither supply is powered up for extended periods of time if the other
supply is below the proper operating voltage.
system-level design considerations
System-level design considerations, such as bus contention, may require supply sequencing to be
implemented. In this case, the core supply should be powered up at the same time as, or prior to (and powered
down after), the I/O buffers. This is to ensure that the I/O buffers receive valid inputs from the core before the
output buffers are powered up, thus, preventing bus contention with other chips on the board.
power-supply design considerations
For systems using the C6000™ DSP platform of devices, the core supply may be required to provide in excess
of 2 A per DSP until the I/O supply is powered up. This extra current condition is a result of uninitialized logic
within the DSP(s) and is corrected once the CPU sees an internal clock pulse. With the PLL enabled, as the
I/O supply is powered on, a clock pulse is produced stopping the extra current draw from the supply. With the
PLL disabled, an external clock pulse may be required to stop this extra current draw. A normal current state
returns once the I/O power supply is turned on and the CPU sees a clock pulse. Decreasing the amount of time
between the core supply power up and the I/O supply power up can minimize the effects of this current draw.
A dual-power supply with simultaneous sequencing, such as available with TPS563xx controllers or PT69xx
plug-in power modules, can be used to eliminate the delay between core and I/O power up [see the Using the
TPS56300 to Power DSPs application report (literature number SLVA088)]. A Schottky diode can also be used
to tie the core rail to the I/O rail, effectively pulling up the I/O power supply to a level that can help initialize the
logic within the DSP.
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000™ platform of DSPs, the PC board should include separate power planes for
core, I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
25
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
absolute maximum ratings over operating case temperature ranges (unless otherwise noted)†
Supply voltage range, CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 2.3 V
Supply voltage range, DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 4 V
Input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 4 V
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --0.3 V to 4 V
Operating case temperature ranges TC: (A version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --40_C to 105_C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . --65_C to 150_C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
recommended operating conditions
MIN
NOM
MAX
UNIT
CVDD
Supply voltage
1.71
1.8
1.89
V
DVDD
Supply voltage
3.14
3.30
3.46
V
VSS
Supply ground
0
0
0
V
VIH
High-level input voltage
2
VIL
Low-level input voltage
0.8
V
IOH
High-level output current
--12
mA
IOL
Low-level output current
12
mA
TC
Operating case temperature
105
_C
A version
V
--40
electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VOH
High-level output voltage
DVDD = MIN,
IOH = MAX
VOL
Low-level output voltage
DVDD = MIN,
IOL = MAX
0.6
V
II
Input current‡
VI = VSS to DVDD
±10
uA
IOZ
Off-state output current
VO = DVDD or 0 V
±10
uA
IDD2V
Supply current, CPU + CPU memory access§
CVDD = NOM,
CPU clock = 167 MHz
380
mA
IDD2V
Supply current, peripherals§
CVDD = NOM,
CPU clock = 167 MHz
240
mA
IDD3V
Supply current, I/O pins§
DVDD = NOM,
CPU clock = 167 MHz
90
mA
Ci
Input capacitance
10
pF
Co
Output capacitance
10
pF
‡
2.4
V
TMS and TDI are not included due to internal pullups. TRST is not included due to internal pulldown.
§ Measured with average activity (50% high / 50% low power). For more details on CPU, peripheral, and I/O activity, see the TMS320C6000 Power
Consumption Summary application report (literature number SPRA486).
26
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
PARAMETER MEASUREMENT INFORMATION
IOL
Tester Pin
Electronics
50 Ω
Vcomm
Output
Under
Test
CT†
IOH
Where:
IOL
IOH
Vcomm
CT
† Typical distributed load circuit capacitance
=
=
=
=
2 mA
2 mA
0.8 V
15--30-pF typical load-circuit capacitance
Figure 6. TTL-Level Outputs
signal transition levels
All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
Vref = 1.5 V
Figure 7. Input and Output Voltage Reference Levels for AC Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, and
VOL MAX and VOH MIN for output clocks.
Vref = VIH MIN (or VOH MIN)
Vref = VIL MAX (or VOL MAX)
Figure 8. Rise and Fall Transition Time Voltage Reference Levels
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
27
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
INPUT AND OUTPUT CLOCKS
timing requirements for CLKIN†‡ (see Figure 9)
--200
CLKMODE
= x4
NO.
MIN
†
‡
1
tc(CLKIN)
Cycle time, CLKIN
2
tw(CLKINH)
3
4
CLKMODE
= x1
MAX
MIN
UNIT
MAX
20
5
ns
Pulse duration, CLKIN high
0.4C
0.45C
ns
tw(CLKINL)
Pulse duration, CLKIN low
0.4C
tt(CLKIN)
Transition time, CLKIN
0.45C
ns
5
0.6
ns
The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns.
1
4
2
CLKIN
3
4
Figure 9. CLKIN Timing Diagram
switching characteristics over recommended operating conditions for CLKOUT1§¶#
(see Figure 10)
--200
NO.
CLKMODE = x4
PARAMETER
MIN
1
tc(CKO1)
Cycle time, CLKOUT1
2
tw(CKO1H)
3
tw(CKO1L)
4
tt(CKO1)
Transition time, CLKOUT1
CLKMODE = x1
MAX
MIN
P -- 0.7
P + 0.7
P -- 0.7
P + 0.7
ns
Pulse duration, CLKOUT1 high
(P/2) -- 0.5
(P/2 ) + 0.5
PH -- 0.5
PH + 0.5
ns
Pulse duration, CLKOUT1 low
(P/2) -- 0.5
(P/2 ) + 0.5
PL -- 0.5
PL + 0.5
ns
0.6
ns
0.6
§
P = 1/CPU clock frequency in ns.
The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
# PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
¶
1
4
2
CLKOUT1
3
4
Figure 10. CLKOUT1 Timing Diagram
28
UNIT
MAX
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
switching characteristics over recommended operating conditions for CLKOUT2†‡ (see Figure 11)
NO
NO.
†
‡
--200
PARAMETER
MIN
MAX
UNIT
1
tc(CKO2)
Cycle time, CLKOUT2
2P -- 0.7
2P + 0.7
ns
2
tw(CKO2H)
Pulse duration, CLKOUT2 high
P -- 0.7
P + 0.7
ns
3
tw(CKO2L)
Pulse duration, CLKOUT2 low
P -- 0.7
P + 0.7
ns
4
tt(CKO2)
Transition time, CLKOUT2
0.6
ns
P = 1/CPU clock frequency in ns.
The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
1
4
2
CLKOUT2
3
4
Figure 11. CLKOUT2 Timings
SDCLK, SSCLK timing parameters
SDCLK timing parameters are the same as CLKOUT2 parameters.
SSCLK timing parameters are the same as CLKOUT1 or CLKOUT2 parameters, depending on SSCLK
configuration.
switching characteristics over recommended operating conditions for the relation of SSCLK,
SDCLK, and CLKOUT2 to CLKOUT1 (see Figure 12)†
NO
NO.
†
--200
PARAMETER
MIN
MAX
UNIT
1
td(CKO1-SSCLK)
Delay time, CLKOUT1 edge to SSCLK edge
(P/2) + 0.2
(P/2) + 4.2
ns
2
td(CKO1-SSCLK1/2)
Delay time, CLKOUT1 edge to SSCLK edge (1/2 clock rate)
(P/2) -- 1
(P/2) + 2.4
ns
3
td(CKO1-CKO2)
Delay time, CLKOUT1 edge to CLKOUT2 edge
(P/2) -- 1
(P/2) + 2.4
ns
4
td(CKO1-SDCLK)
Delay time, CLKOUT1 edge to SDCLK edge
(P/2) -- 1
(P/2) + 2.4
ns
P = 1/CPU clock frequency in ns.
CLKOUT1
1
SSCLK
2
SSCLK (1/2rate)
3
CLKOUT2
4
SDCLK
Figure 12. Relation of CLKOUT2, SDCLK, and SSCLK to CLKOUT1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
29
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
ASYNCHRONOUS MEMORY TIMING
timing requirements for asynchronous memory cycles† (see Figure 13 and Figure 14)
--200
NO
NO.
†
MIN
6
tsu(EDV-CKO1H)
Setup time, read EDx valid before CLKOUT1 high
7
th(CKO1H-EDV)
Hold time, read EDx valid after CLKOUT1 high
10
tsu(ARDY-CKO1H)
Setup time, ARDY valid before CLKOUT1 high
11
th(CKO1H-ARDY)
Hold time, ARDY valid after CLKOUT1 high
MAX
UNIT
4
ns
0.8
ns
3
ns
1.8
ns
To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. If ARDY does meet setup or hold
time, it may be recognized in the current cycle or the next cycle. Thus, ARDY can be an asynchronous input.
switching characteristics over recommended operating conditions for asynchronous memory
cycles‡ (see Figure 13 and Figure 14)
NO
NO.
‡
PARAMETER
UNIT
MAX
--0.2
4
ns
4
ns
1
td(CKO1H-CEV)
Delay time, CLKOUT1 high to CEx valid
2
td(CKO1H-BEV)
Delay time, CLKOUT1 high to BEx valid
3
td(CKO1H-BEIV)
Delay time, CLKOUT1 high to BEx invalid
4
td(CKO1H-EAV)
Delay time, CLKOUT1 high to EAx valid
5
td(CKO1H-EAIV)
Delay time, CLKOUT1 high to EAx invalid
--0.2
8
td(CKO1H-AOEV)
Delay time, CLKOUT1 high to AOE valid
--0.2
4
ns
9
td(CKO1H-AREV)
Delay time, CLKOUT1 high to ARE valid
--0.2
4
ns
12
td(CKO1H-EDV)
Delay time, CLKOUT1 high to EDx valid
4
ns
13
td(CKO1H-EDIV)
Delay time, CLKOUT1 high to EDx invalid
--0.2
14
td(CKO1H-AWEV)
Delay time, CLKOUT1 high to AWE valid
--0.2
The minimum delay is also the minimum output hold after CLKOUT1 high.
30
--200
MIN
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
--0.2
ns
4
ns
ns
ns
4
ns
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Not ready = 2
Strobe = 5
HOLD = 1
CLKOUT1
1
1
2
3
4
5
CEx
BE[3:0]
EA[21:2]
7
6
ED[31:0]
8
8
AOE
9
9
ARE
AWE
10
11
10
11
ARDY
Figure 13. Asynchronous Memory Read Timing
Setup = 2
Not ready = 2
Strobe = 5
HOLD = 1
CLKOUT1
1
1
2
3
4
5
CEx
BE[3:0]
EA[21:2]
12
13
ED[31:0]
AOE
ARE
14
14
AWE
10
11
10
11
ARDY
Figure 14. Asynchronous Memory Write Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
31
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS-BURST MEMORY TIMING
timing requirements for synchronous-burst SRAM cycles (full-rate SSCLK) (see Figure 15)
--200
NO
NO.
MIN
MAX
UNIT
7
tsu(EDV-SSCLKH)
Setup time, read EDx valid before SSCLK high
1.5
ns
8
th(SSCLKH-EDV)
Hold time, read EDx valid after SSCLK high
1.5
ns
switching characteristics over recommended operating conditions for synchronous-burst SRAM
cycles† (full-rate SSCLK) (see Figure 15 and Figure 16)
NO
NO.
†
--200
PARAMETER
MIN
MAX
UNIT
1
tosu(CEV-SSCLKH)
Output setup time, CEx valid before SSCLK high
0.5P -- 1.3
ns
2
toh(SSCLKH-CEV)
Output hold time, CEx valid after SSCLK high
0.5P -- 2.3
ns
3
tosu(BEV-SSCLKH)
Output setup time, BEx valid before SSCLK high
0.5P -- 1.3
ns
4
toh(SSCLKH-BEIV)
Output hold time, BEx invalid after SSCLK high
0.5P -- 2.3
ns
5
tosu(EAV-SSCLKH)
Output setup time, EAx valid before SSCLK high
0.5P -- 1.3
ns
6
toh(SSCLKH-EAIV)
Output hold time, EAx invalid after SSCLK high
0.5P -- 2.3
ns
9
tosu(ADSV-SSCLKH)
Output setup time, SSADS valid before SSCLK high
0.5P -- 1.3
ns
10
toh(SSCLKH-ADSV)
Output hold time, SSADS valid after SSCLK high
0.5P -- 2.3
ns
11
tosu(OEV-SSCLKH)
Output setup time, SSOE valid before SSCLK high
0.5P -- 1.3
ns
12
toh(SSCLKH-OEV)
Output hold time, SSOE valid after SSCLK high
0.5P -- 2.3
ns
13
tosu(EDV-SSCLKH)
Output setup time, EDx valid before SSCLK high
0.5P -- 1.3
ns
14
toh(SSCLKH-EDIV)
Output hold time, EDx invalid after SSCLK high
0.5P -- 2.3
ns
15
tosu(WEV-SSCLKH)
Output setup time, SSWE valid before SSCLK high
0.5P -- 1.3
ns
16
toh(SSCLKH-WEV)
Output hold time, SSWE valid after SSCLK high
0.5P -- 2.3
ns
When the PLL is used (CLKMODE x4), P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For CLKMODE x1, 0.5P is defined as PH (pulse duration of CLKIN high) for all output setup times; 0.5P is defined as PL (pulse duration of CLKIN
low) for all output hold times.
32
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
SSCLK
CEx
1
2
3
BE[3:0]
BE1
BE2
BE3
4
BE4
A1
A2
A3
6
A4
5
EA[21:2]
7
8
Q1
ED[31:0]
9
Q2
Q3
Q4
10
SSADS
11
12
SSOE
SSWE
Figure 15. SBSRAM Read Timing (Full-Rate SSCLK)
SSCLK
1
2
CEx
3
BE[3:0]
BE1
BE2
BE3
4
BE4
A1
A2
A3
6
A4
Q3
14
Q4
5
EA[21:2]
13
ED[31:0]
Q1
Q2
9
10
15
16
SSADS
SSOE
SSWE
Figure 16. SBSRAM Write Timing (Full-Rate SSCLK)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
33
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
timing requirements for synchronous-burst SRAM cycles (half-rate SSCLK) (see Figure 17)
--200
NO
NO.
MIN
MAX
UNIT
7
tsu(EDV-SSCLKH)
Setup time, read EDx valid before SSCLK high
2.5
ns
8
th(SSCLKH-EDV)
Hold time, read EDx valid after SSCLK high
1.5
ns
switching characteristics over recommended operating conditions for synchronous-burst SRAM
cycles† (half-rate SSCLK) (see Figure 17 and Figure 18)
NO
NO.
†
--200
PARAMETER
MIN
1
tosu(CEV-SSCLKH)
Output setup time, CEx valid before SSCLK high
2
toh(SSCLKH-CEV)
Output hold time, CEx valid after SSCLK high
3
tosu(BEV-SSCLKH)
Output setup time, BEx valid before SSCLK high
4
toh(SSCLKH-BEIV)
Output hold time, BEx invalid after SSCLK high
5
tosu(EAV-SSCLKH)
Output setup time, EAx valid before SSCLK high
6
toh(SSCLKH-EAIV)
Output hold time, EAx invalid after SSCLK high
9
tosu(ADSV-SSCLKH)
Output setup time, SSADS valid before SSCLK high
10
toh(SSCLKH-ADSV)
Output hold time, SSADS valid after SSCLK high
11
tosu(OEV-SSCLKH)
Output setup time, SSOE valid before SSCLK high
12
toh(SSCLKH-OEV)
Output hold time, SSOE valid after SSCLK high
13
tosu(EDV-SSCLKH)
Output setup time, EDx valid before SSCLK high
14
toh(SSCLKH-EDIV)
Output hold time, EDx invalid after SSCLK high
15
tosu(WEV-SSCLKH)
Output setup time, SSWE valid before SSCLK high
16
toh(SSCLKH-WEV)
Output hold time, SSWE valid after SSCLK high
MAX
UNIT
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
1.5P -- 3
ns
0.5P -- 1.5
ns
When the PLL is used (CLKMODE x4), P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For CLKMODE x1:
1.5P = P + PH, where P = 1/CPU clock frequency, and PH = pulse duration of CLKIN high.
0.5P = PL, where PL = pulse duration of CLKIN low.
34
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS-BURST MEMORY TIMING (CONTINUED)
SSCLK
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
6
7
Q1
ED[31:0]
8
Q2
Q3
9
Q4
10
SSADS
11
12
SSOE
SSWE
Figure 17. SBSRAM Read Timing (1/2 Rate SSCLK)
SSCLK
1
2
CEx
BE[3:0]
3
BE1
BE2
BE3
BE4
4
EA[21:2]
5
A1
A2
A3
A4
Q1
Q2
Q3
Q4
6
13
ED[31:0]
14
9
10
15
16
SSADS
SSOE
SSWE
Figure 18. SBSRAM Write Timing (1/2 Rate SSCLK)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
35
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS DRAM TIMING
timing requirements for synchronous DRAM cycles (see Figure 19)
--200
NO
NO.
MIN
7
tsu(EDV-SDCLKH)
Setup time, read EDx valid before SDCLK high
8
th(SDCLKH-EDV)
Hold time, read EDx valid after SDCLK high
MAX
UNIT
0.5
ns
3
ns
switching characteristics over recommended operating conditions for synchronous DRAM
cycles† (see Figure 19--Figure 24)
NO
NO.
†
--200
PARAMETER
MIN
1
tosu(CEV-SDCLKH)
Output setup time, CEx valid before SDCLK high
2
toh(SDCLKH-CEV)
Output hold time, CEx valid after SDCLK high
3
tosu(BEV-SDCLKH)
Output setup time, BEx valid before SDCLK high
4
toh(SDCLKH-BEIV)
Output hold time, BEx invalid after SDCLK high
5
tosu(EAV-SDCLKH)
Output setup time, EAx valid before SDCLK high
6
toh(SDCLKH-EAIV)
Output hold time, EAx invalid after SDCLK high
9
tosu(SDCAS-SDCLKH)
Output setup time, SDCAS valid before SDCLK high
10
toh(SDCLKH-SDCAS)
MAX
UNIT
1.5P -- 3.5
ns
0.5P -- 1
ns
1.5P -- 3.5
ns
0.5P -- 1
ns
1.5P -- 3.5
ns
0.5P -- 1
ns
1.5P -- 3.5
ns
Output hold time, SDCAS valid after SDCLK high
0.5P -- 1
ns
1.5P -- 3.5
ns
0.5P -- 1
ns
1.5P -- 3.5
ns
11
tosu(EDV-SDCLKH)
Output setup time, EDx valid before SDCLK high
12
toh(SDCLKH-EDIV)
Output hold time, EDx invalid after SDCLK high
13
tosu(SDWE-SDCLKH)
Output setup time, SDWE valid before SDCLK high
14
toh(SDCLKH-SDWE)
Output hold time, SDWE valid after SDCLK high
15
tosu(SDA10V-SDCLKH)
Output setup time, SDA10 valid before SDCLK high
16
toh(SDCLKH-SDA10IV)
Output hold time, SDA10 invalid after SDCLK high
17
tosu(SDRAS-SDCLKH)
Output setup time, SDRAS valid before SDCLK high
18
toh(SDCLKH-SDRAS)
Output hold time, SDRAS valid after SDCLK high
0.5P -- 1
ns
1.5P -- 3.5
ns
0.5P -- 1
ns
1.5P -- 3.5
ns
0.5P -- 1
ns
When the PLL is used (CLKMODE x4), P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For CLKMODE x1:
1.5P = P + PH, where P = 1/CPU clock frequency, and PH = pulse duration of CLKIN high.
0.5P = PL, where PL = pulse duration of CLKIN low.
36
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
READ
READ
READ
SDCLK
1
2
CEx
3
BE[3:0]
5
EA[15:2]
4
BE1
BE2
CA2
CA3
BE3
6
CA1
7
8
D1
ED[31:0]
15
16
9
10
D2
D3
SDA10
SDRAS
SDCAS
SDWE
Figure 19. Three SDRAM Read Commands
WRITE
WRITE
WRITE
SDCLK
1
2
CEx
3
BE[3:0]
4
BE1
5
EA[15:2]
BE3
CA2
CA3
D2
D3
6
CA1
11
D1
ED[31:0]
BE2
12
15
16
9
10
13
14
SDA10
SDRAS
SDCAS
SDWE
Figure 20. Three SDRAM WRT Commands
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
37
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
ACTV
SDCLK
1
2
CEx
BE[3:0]
5
Bank Activate/Row Address
EA[15:2]
ED[31:0]
15
Row Address
SDA10
17
18
SDRAS
SDCAS
SDWE
Figure 21. SDRAM ACTV Command
DCAB
SDCLK
1
2
15
16
17
18
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
SDRAS
SDCAS
13
SDWE
Figure 22. SDRAM DCAB Command
38
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
14
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
REFR
SDCLK
1
2
CEx
BE[3:0]
EA[15:2]
ED[31:0]
SDA10
17
18
SDRAS
9
10
SDCAS
SDWE
Figure 23. SDRAM REFR Command
MRS
SDCLK
1
2
5
6
CEx
BE[3:0]
EA[15:2]
MRS Value
ED[31:0]
SDA10
17
18
9
10
13
14
SDRAS
SDCAS
SDWE
Figure 24. SDRAM MRS Command
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
39
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
HOLD/HOLDA TIMING
timing requirements for the HOLD/HOLDA cycles† (see Figure 25)
--200
NO
NO.
†
MIN
MAX
UNIT
1
tsu(HOLDH-CKO1H)
Setup time, HOLD high before CLKOUT1 high
1
ns
2
th(CKO1H-HOLDL)
Hold time, HOLD low after CLKOUT1 high
4
ns
HOLD is synchronized internally. Therefore, if setup and hold times are not met, it will either be recognized in the current cycle or in the next cycle.
Thus, HOLD can be an asynchronous input.
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles‡
(see Figure 25)
NO
NO.
--200
PARAMETER
3
td(HOLDL-BHZ)
Delay time, HOLD low to EMIF Bus high impedance
4
td(BHZ-HOLDAL)
Delay time, EMIF Bus high impedance to HOLDA low
5
td(HOLDH-HOLDAH)
Delay time, HOLD high to HOLDA high
6
td(CKO1H-HOLDAL)
Delay time, CLKOUT1 high to HOLDA valid
impedance¶
7
td(CKO1H-BHZ)
Delay time, CLKOUT1 high to EMIF Bus high
8
td(CKO1H-BLZ)
Delay time, CLKOUT1 high to EMIF Bus low impedance¶
9
td(HOLDH-BLZ)
Delay time, HOLD high to EMIF Bus low impedance
UNIT
MIN
MAX
4P
§
ns
P
2P
ns
4P
7P
ns
1
8
ns
3
11
ns
3
11
ns
3P
6P
ns
‡
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
All pending EMIF transactions are allowed to complete before HOLDA is asserted. The worst cases for this is an asynchronous read or write
with external ARDY used or a minimum of eight consecutive SDRAM reads or writes when RBTR8 = 1. If no bus transactions are occurring, then
the minimum delay time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
¶ EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SSADS, SSOE, SSWE, SDA10, SDRAS, SDCAS, and SDWE.
§
DSP Owns Bus
External Requester
DSP Owns Bus
5
9
4
3
CLKOUT1
2
2
1
1
HOLD
6
6
HOLDA
7
8
EMIF Bus†
†
C62x
Ext Req
C62x
EMIF Bus consists of CE[3:0], BE[3:0], ED[31:0], EA[21:2], ARE, AOE, AWE, SSADS, SSOE, SSWE, SDA10, SDRAS, SDCAS, and SDWE.
Figure 25. HOLD/HOLDA Timing
40
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
RESET TIMING
timing requirements for reset (see Figure 26)
--200
NO
NO.
1
MIN
tw(RST)
Width of the RESET pulse (PLL stable)†
Width of the RESET pulse (PLL needs to sync up)‡
MAX
UNIT
10
CLKOUT1
cycles
250
μs
†
This parameter applies to CLKMODE x1 when CLKIN is stable and applies to CLKMODE x4 when CLKIN and PLL are stable.
‡ This parameter only applies to CLKMODE x4. The RESET signal is not connected internally to the clock PLL circuit. The PLL, however, may
need up to 250 μs to stabilize following device power up or after PLL configuration has been changed. During that time, RESET must be asserted
to ensure proper device operation. See the Clock PLL section for PLL lock times.
switching characteristics over recommended operating conditions during reset§¶ (see Figure 26)
NO
NO.
--200
PARAMETER
MIN
2
tR(RST)
Response time to change of value in RESET signal
3
td(CKO1H-CKO2IV)
Delay time, CLKOUT1 high to CLKOUT2 invalid
4
td(CKO1H-CKO2V)
Delay time, CLKOUT1 high to CLKOUT2 valid
5
td(CKO1H-SDCLKIV)
Delay time, CLKOUT1 high to SDCLK invalid
6
td(CKO1H-SDCLKV)
Delay time, CLKOUT1 high to SDCLK valid
7
td(CKO1H-SSCKIV)
Delay time, CLKOUT1 high to SSCLK invalid
8
td(CKO1H-SSCKV)
Delay time, CLKOUT1 high to SSCLK valid
9
td(CKO1H-LOWIV)
Delay time, CLKOUT1 high to low group invalid
10
td(CKO1H-LOWV)
Delay time, CLKOUT1 high to low group valid
11
td(CKO1H-HIGHIV)
Delay time, CLKOUT1 high to high group invalid
12
td(CKO1H-HIGHV)
Delay time, CLKOUT1 high to high group valid
13
td(CKO1H-ZHZ)
Delay time, CLKOUT1 high to Z group high impedance
14
td(CKO1H-ZV)
Delay time, CLKOUT1 high to Z group valid
§
Low group consists of:
High group consists of:
Z group consists of:
¶
HRDY is gated by input HCS.
If HCS = 0 at device reset, HRDY belongs to the high group.
If HCS = 1 at device reset, HRDY belongs to the low group.
MAX
UNIT
CLKOUT1
cycles
2
--1
ns
10
--1
ns
ns
10
--1
ns
ns
10
--1
ns
ns
10
--1
ns
ns
10
--1
ns
ns
10
ns
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1
HINT
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SSADS, SSOE, SSWE, SDA10, SDRAS, SDCAS,
SDWE, HD[15:0], CLKX0, CLKX1, FSX0, FSX1, DX0, DX1, CLKR0, CLKR1, FSR0, and FSR1.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
41
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
RESET TIMING (CONTINUED)
CLKOUT1
1
2
2
RESET
3
4
5
6
7
8
9
10
11
12
13
14
CLKOUT2
SDCLK
SSCLK
LOW GROUP†‡
HIGH GROUP†‡
Z GROUP†‡
†
Low group consists of:
High group consists of:
Z group consists of:
‡
HRDY is gated by input HCS.
If HCS = 0 at device reset, HRDY belongs to the high group.
If HCS = 1 at device reset, HRDY belongs to the low group.
IACK, INUM[3:0], DMAC[3:0], PD, TOUT0, and TOUT1
HINT
EA[21:2], ED[31:0], CE[3:0], BE[3:0], ARE, AWE, AOE, SSADS, SSOE, SSWE, SDA10, SDRAS, SDCAS,
SDWE, HD[15:0], CLKX0, CLKX1, FSX0, FSX1, DX0, DX1, CLKR0, CLKR1, FSR0, and FSR1.
Figure 26. Reset Timing
42
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
EXTERNAL INTERRUPT TIMING
timing requirements for interrupt response cycles†‡ (see Figure 27)
--200
NO
NO.
MIN
MAX
UNIT
2
tw(ILOW)
Width of the interrupt pulse low
2P
ns
3
tw(IHIGH)
Width of the interrupt pulse high
2P
ns
†
Interrupt signals are synchronized internally and are potentially recognized one cycle later if setup and hold times are violated. Thus, they can
be connected to asynchronous inputs.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
switching characteristics over recommended operating conditions during interrupt response
cycles§ (see Figure 27)
NO
NO.
§
--200
PARAMETER
MIN
1
td(EINTH-IACKH)
Delay time, EXT_INTx high to IACK high
9P
4
td(CKO2L-IACKV)
Delay time, CLKOUT2 low to IACK valid
--4
5
td(CKO2L-INUMV)
Delay time, CLKOUT2 low to INUMx valid
6
td(CKO2L-INUMIV)
Delay time, CLKOUT2 low to INUMx invalid
MAX
UNIT
ns
--4
6
ns
6
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
When the PLL is used (CLKMODE x4), 0.5P = 1/(2 × CPU clock frequency).
For CLKMODE x1: 0.5P = PH, where PH is the high period of CLKIN.
1
CLKOUT2
2
3
EXT_INTx, NMI
Intr Flag
4
4
IACK
6
5
INUMx
Interrupt Number
Figure 27. Interrupt Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
43
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
HOST-PORT INTERFACE TIMING
timing requirements for host-port interface cycles†‡ (see Figure 28, Figure 29, Figure 30, and
Figure 31)
--200
NO
NO.
MIN
MAX
UNIT
1
tsu(SEL-HSTBL)
Setup time, select signals§ valid before HSTROBE low
4
ns
2
th(HSTBL-SEL)
Hold time, select signals§ valid after HSTROBE low
2
ns
3
tw(HSTBL)
Pulse duration, HSTROBE low
2P
ns
4
tw(HSTBH)
Pulse duration, HSTROBE high between consecutive accesses
2P
ns
10
tsu(SEL-HASL)
Setup time, select signals§ valid before HAS low
4
ns
signals§
11
th(HASL-SEL)
Hold time, select
2
ns
12
tsu(HDV-HSTBH)
Setup time, host data valid before HSTROBE high
valid after HAS low
3
ns
13
th(HSTBH-HDV)
Hold time, host data valid after HSTROBE high
2
ns
14
th(HRDYL-HSTBL)
Hold time, HSTROBE low after HRDY low. HSTROBE should not be inactivated
until HRDY is active (low); otherwise, HPI writes will not complete properly.
1
ns
18
tsu(HASL-HSTBL)
Setup time, HAS low before HSTROBE low
2
ns
19
th(HSTBL-HASL)
Hold time, HAS low after HSTROBE low
2
ns
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
‡ The effects of internal clock jitter are included at test. There is no need to adjust timing numbers for internal clock jitter. P = 1/CPU clock frequency
in ns. For example, when running parts at 200 MHz, use P = 5 ns.
§ Select signals include: HCNTRL[1:0], HR/W, and HHWIL.
switching characteristics over recommended operating conditions during host-port interface
cycles†‡ (see Figure 28, Figure 29, Figure 30, and Figure 31)
NO
NO.
5
†
‡
¶
#
||
--200
PARAMETER
td(HCS-HRDY)
MIN
Delay time, HCS to HRDY¶
high#
6
td(HSTBL-HRDYH)
Delay time, HSTROBE low to HRDY
7
toh(HSTBL-HDLZ)
Output hold time, HD low impedance after HSTROBE low for an HPI read
8
td(HDV-HRDYL)
Delay time, HD valid to HRDY low
MAX
UNIT
1
9
ns
3
12
ns
4
P -- 3
ns
P+3
ns
9
toh(HSTBH-HDV)
Output hold time, HD valid after HSTROBE high
2
12
ns
15
td(HSTBH-HDHZ)
Delay time, HSTROBE high to HD high impedance
3
12
ns
16
td(HSTBL-HDV)
Delay time, HSTROBE low to HD valid
2
12
ns
17
td(HSTBH-HRDYH)
Delay time, HSTROBE high to HRDY high||
3
12
ns
20
td(HASL-HRDYH)
Delay time, HAS low to HRDY high
3
12
ns
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
The effects of internal clock jitter are included at test. There is no need to adjust timing numbers for internal clock jitter. P = 1/CPU clock frequency
in ns. For example, when running parts at 200 MHz, use P = 5 ns.
HCS enables HRDY, and HRDY is always low when HCS is high. The case where HRDY goes high when HCS falls indicates that HPI is busy
completing a previous HPID write or READ with autoincrement.
This parameter is used during an HPID read. At the beginning of the first half-word transfer on the falling edge of HSTROBE, the HPI sends the
request to the DMA auxiliary channel, and HRDY remains high until the DMA auxiliary channel loads the requested data into HPID.
This parameter is used after the second half-word of an HPID write or autoincrement read. HRDY remains low if the access is not an HPID write
or autoincrement read. Reading or writing to HPIC or HPIA does not affect the HRDY signal.
44
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
HOST-PORT INTERFACE TIMING (CONTINUED)
HAS
1
1
2
2
HCNTL[1:0]
1
1
2
2
HR/W
1
1
2
2
HHWIL
4
3
HSTROBE†
3
HCS
15
9
7
15
9
16
HD[15:0] (output)
1st Half-Word
5
2nd Half-Word
8
17
HRDY (case 1)
6
8
17
HRDY (case 2)
†
5
5
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 28. HPI Read Timing (HAS Not Used, Tied High)
HAS
19
11
19
10
11
10
HCNTL[1:0]
11
10
11
10
HR/W
11
11
10
10
HHWIL
4
3
HSTROBE†
18
18
HCS
7
15
9
16
9
15
HD[15:0] (output)
1st half-word
5
8
2nd half-word
17
5
17
5
HRDY (case 1)
20
8
HRDY (case 2)
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 29. HPI Read Timing (HAS Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
45
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
HOST-PORT INTERFACE TIMING (CONTINUED)
HAS
1
1
2
HCNTL[1:0]
12
2
12
13
13
HBE[1:0]
1
1
2
2
HR/W
1
1
2
2
HHWIL
3
14
HSTROBE†
3
4
HCS
12
12
13
13
HD[15:0] (input)
1st Half-Word
5
17
2nd Half-Word
5
HRDY
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 30. HPI Write Timing (HAS Not Used, Tied High)
HAS
12
19
13
12
19
13
HBE[1:0]
11
10
11
10
HCNTL[1:0]
11
10
11
10
HR/W
11
10
11
10
HHWIL
3
14
HSTROBE†
4
18
18
HCS
12
13
12
13
HD[15:0] (input)
5
1st half-word
2nd half-word
17
HRDY
†
HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 31. HPI Write Timing (HAS Used)
46
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
5
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING
timing requirements for McBSP†‡(see Figure 32)
--200
NO
NO.
MIN
MAX
UNIT
2
tc(CKRX)
Cycle time, CLKR/X
CLKR/X ext
2P§
ns
3
tw(CKRX)
Pulse duration, CLKR/X high or CLKR/X low
CLKR/X ext
P -- 1¶
ns
5
tsu(FRH-CKRL)
Setup time,
time external FSR high before CLKR low
6
th(CKRL-FRH)
Hold time,
time external FSR high after CLKR low
7
tsu(DRV-CKRL)
Setup time
time, DR valid before CLKR low
8
th(CKRL-DRV)
Hold time
time, DR valid after CLKR low
10
tsu(FXH-CKXL)
Setup time,
time external FSX high before CLKX low
11
th(CKXL-FXH)
Hold time,
time external FSX high after CLKX low
CLKR int
9
CLKR ext
2
CLKR int
6
CLKR ext
3
CLKR int
8
CLKR ext
0
CLKR int
3
CLKR ext
4
CLKX int
9
CLKX ext
2
CLKX int
6
CLKX ext
3
ns
ns
ns
ns
ns
ns
†
CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
§ The maximum bit rate for the C6202/02B/03 device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 200 MHz
(P = 5 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
¶ The minimum CLKR/X pulse duration is either (P--1) or 4 ns, whichever is larger. For example, when running parts at 200 MHz (P = 5 ns), use
4 ns as the minimum CLKR/X pulse duration. When running parts at 100 MHz (P = 10 ns), use (P--1) = 9 ns as the minimum CLKR/X pulse
duration.
‡
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
47
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP†‡§ (see Figure 32)
NO
NO.
--200
PARAMETER
1
td(CKSH-CKRXH)
Delay time, CLKS high to CLKR/X high for internal CLKR/X
generated from CLKS input
2
tc(CKRX)
Cycle time, CLKR/X
MIN
MAX
3
10
CLKR/X int
2P¶
1.3#
ns
ns
Pulse duration, CLKR/X high or CLKR/X low
CLKR/X int
td(CKRH-FRV)
Delay time, CLKR high to internal FSR valid
CLKR int
--2
3
CLKX int
--2
3
CLKX ext
3
9
Dela time,
Delay
time CLKX high to internal FSX valid
alid
12
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
13
td(CKXH-DXV)
Dela time,
Delay
time CLKX high to DX valid
alid
14
td(FXH-DXV)
C+
ns
tw(CKRX)
4
td(CKXH-FXV)
ns
1#
3
9
C --
UNIT
CLKX int
--1
4
CLKX ext
3
9
CLKX int
--1
4
CLKX ext
3
9
Delay time, FSX high to DX valid
FSX int
--1
3
ONLY applies when in data
delay 0 (XDATDLY = 00b) mode
FSX ext
3
9
ns
ns
ns
ns
†
CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
Minimum delay times also represent minimum output hold times.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
¶ The maximum bit rate for the C6202/02B/03 device is 100 Mbps or CPU/2 (the slower of the two). Care must be taken to ensure that the AC timings
specified in this data sheet are met. The maximum bit rate for McBSP-to-McBSP communications is 100 MHz; therefore, the minimum CLKR/X
clock cycle is either twice the CPU cycle time (2P), or 10 ns (100 MHz), whichever value is larger. For example, when running parts at 200 MHz
(P = 5 ns), use 10 ns as the minimum CLKR/X clock cycle (by setting the appropriate CLKGDV ratio or external clock source). When running
parts at 100 MHz (P = 10 ns), use 2P = 20 ns (50 MHz) as the minimum CLKR/X clock cycle. The maximum bit rate for McBSP-to-McBSP
communications applies when the serial port is a master of the clock and frame syncs (with CLKR connected to CLKX, FSR connected to FSX,
CLKXM = FSXM = 1, and CLKRM = FSRM = 0) in data delay 1 or 2 mode (R/XDATDLY = 01b or 10b) and the other device the McBSP
communicates to is a slave.
# C = H or L
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width
= (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width
= (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
‡
48
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKS
1
2
3
3
CLKR
4
FSR (int)
4
5
6
FSR (ext)
7
DR
2
3
8
Bit(n-1)
(n-2)
(n-3)
3
CLKX
9
FSX (int)
10
11
FSX (ext)
FSX (XDATDLY=00b)
12
DX
Bit 0
14
13
Bit(n-1)
13
(n-2)
(n-3)
Figure 32. McBSP Timing Diagram
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
49
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for FSR when GSYNC = 1 (see Figure 33)
--200
NO
NO.
MIN
MAX
UNIT
1
tsu(FRH-CKSH)
Setup time, FSR high before CLKS high
4
ns
2
th(CKSH-FRH)
Hold time, FSR high after CLKS high
4
ns
CLKS
1
FSR External
2
CLKR/X (no need to resync)
CLKR/X (needs resync)
Figure 33. FSR Timing When GSYNC = 1
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 0†‡
(see Figure 34)
--200
MASTER
NO.
MIN
4
tsu(DRV-CKXL)
Setup time, DR valid before CLKX low
5
th(CKXL-DRV)
Hold time, DR valid after CLKX low
†
MAX
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
UNIT
MAX
12
2 -- 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
50
SLAVE
MIN
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 34)
--200
NO.
‡
§
¶
#
PARAMETER
SLAVE
MIN
MAX
th(CKXL-FXL)
Hold time, FSX low after CLKX low¶
T -- 2
T+3
2
td(FXL-CKXH)
Delay time, FSX low to CLKX
high#
L -- 2
L+3
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
--2
4
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX low
L -- 2
L+3
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
8
td(FXL-DXV)
Delay time, FSX low to DX valid
1
†
MASTER§
MIN
UNIT
MAX
ns
ns
3P + 4
5P + 17
ns
ns
P+3
3P + 17
ns
2P + 2
4P + 17
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
51
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 34. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 35)
--200
MASTER
NO.
MIN
4
tsu(DRV-CKXH)
Setup time, DR valid before CLKX high
5
th(CKXH-DRV)
Hold time, DR valid after CLKX high
SLAVE
MAX
MIN
UNIT
MAX
12
2 -- 3P
ns
4
5 + 6P
ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
‡ For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 35)
--200
NO.
MASTER§
PARAMETER
MIN
†
‡
§
¶
#
SLAVE
MAX
MIN
UNIT
MAX
1
th(CKXL-FXL)
Hold time, FSX low after CLKX low¶
L -- 2
L+3
2
td(FXL-CKXH)
Delay time, FSX low to CLKX high#
T -- 2
T+3
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
--2
4
3P + 4
5P + 17
ns
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX low
--2
4
3P + 3
5P + 17
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
H -- 2
H+4
2P + 2
4P + 17
ns
ns
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
52
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
6
Bit 0
7
FSX
DX
3
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 35. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 36)
--200
MASTER
NO.
MIN
†
‡
4
tsu(DRV-CKXH)
Setup time, DR valid before CLKX high
5
th(CKXH-DRV)
Hold time, DR valid after CLKX high
SLAVE
MAX
MIN
UNIT
MAX
12
2 -- 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 36)
--200
NO.
1
†
‡
§
¶
#
MASTER§
PARAMETER
th(CKXH-FXL)
Hold time, FSX low after CLKX high¶
low#
2
td(FXL-CKXL)
Delay time, FSX low to CLKX
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
8
td(FXL-DXV)
Delay time, FSX low to DX valid
SLAVE
MIN
MAX
T -- 2
T+3
H -- 2
H+3
--2
4
H -- 2
H+3
MIN
UNIT
MAX
ns
ns
3P + 4
5P + 17
ns
ns
P+3
3P + 17
ns
2P + 2
4P + 17
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
53
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 36. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
timing requirements for McBSP as SPI master or slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 37)
--200
MASTER
NO.
MIN
†
‡
4
tsu(DRV-CKXL)
Setup time, DR valid before CLKX low
5
th(CKXL-DRV)
Hold time, DR valid after CLKX low
SLAVE
MAX
MIN
UNIT
MAX
12
2 -- 3P
ns
4
5 + 6P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI master or
slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 37)
--200
NO.
1
†
‡
§
¶
#
MASTER§
PARAMETER
th(CKXH-FXL)
Hold time, FSX low after CLKX high¶
SLAVE
MIN
MAX
H -- 2
H+3
low#
MIN
UNIT
MAX
ns
2
td(FXL-CKXL)
Delay time, FSX low to CLKX
T -- 2
T+1
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
--2
4
3P + 4
5P + 17
ns
ns
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
--2
4
3P + 3
5P + 17
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
L -- 2
L+4
2P + 2
4P + 17
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
54
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
CLKX
1
2
FSX
7
6
DX
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 37. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
55
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
DMAC, TIMER, POWER-DOWN TIMING
switching characteristics over recommended operating conditions for DMAC outputs
(see Figure 38)
NO
NO.
1
--200
PARAMETER
td(CKO1H-DMACV)
Delay time, CLKOUT1 high to DMAC valid
MIN
MAX
2
10
UNIT
ns
CLKOUT1
1
1
DMAC[0:3]
Figure 38. DMAC Timing Diagram
timing requirements for timer inputs† (see Figure 39)
--200
NO
NO.
1
†
MIN
tw(TINP)
Pulse duration, TINP high or low
MAX
UNIT
2P
ns
P = 1/CPU clock frequency in ns. For example, when running parts at 200 MHz, use P = 5 ns.
switching characteristics over recommended operating conditions for timer outputs
(see Figure 39)
NO
NO.
2
--200
PARAMETER
td(CKO1H-TOUTV)
Delay time, CLKOUT1 high to TOUT valid
MIN
MAX
2
9
UNIT
ns
CLKOUT1
1
TINP
2
2
TOUT
Figure 39. Timer Timing Diagram
switching characteristics over recommended operating conditions for power-down outputs
(see Figure 40)
NO
NO.
1
--200
PARAMETER
td(CKO1H-PDV)
Delay time, CLKOUT1 high to PD valid
CLKOUT1
1
1
PD
Figure 40. Power-Down Timing
56
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
MIN
MAX
2
9
UNIT
ns
SM320C6201-EP
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SGUS041A -- MAY 2003 -- REVISED JANUARY 2004
JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 41)
--200
NO
NO.
MIN
MAX
UNIT
1
tc(TCK)
Cycle time, TCK
35
ns
3
tsu(TDIV-TCKH)
Setup time, TDI/TMS/TRST valid before TCK high
10
ns
4
th(TCKH-TDIV)
Hold time, TDI/TMS/TRST valid after TCK high
9
ns
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 41)
NO
NO.
2
--200
PARAMETER
td(TCKL-TDOV)
Delay time, TCK low to TDO valid
MIN
MAX
--3
12
UNIT
ns
1
TCK
2
2
TDO
3
4
TDI/TMS/TRST
Figure 41. JTAG Test-Port Timing Diagram
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251--1443
57
PACKAGE OPTION ADDENDUM
www.ti.com
24-May-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
SM320C6201GJCA20EP
ACTIVE
FCBGA
GJC
352
21
TBD
SNPB
Level-4-220C-72 HR
V62/04606-01XA
ACTIVE
FCBGA
GJC
352
21
TBD
SNPB
Level-4-220C-72 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated