SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 D D D D D D D D D Members of the Texas Instruments Widebus Family State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC ) Ioff and Power-Up 3-State Support Hot Insertion Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) Package Options Include Plastic Shrink Small-Outline (DL), Thin Shrink Small-Outline (DGG), and Thin Very Small-Outline (DGV) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings SN54LVT16244B . . . WD PACKAGE SN74LVT16244B . . . DGG, DGV, OR DL PACKAGE (TOP VIEW) 1OE 1Y1 1Y2 GND 1Y3 1Y4 VCC 2Y1 2Y2 GND 2Y3 2Y4 3Y1 3Y2 GND 3Y3 3Y4 VCC 4Y1 4Y2 GND 4Y3 4Y4 4OE 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 2OE 1A1 1A2 GND 1A3 1A4 VCC 2A1 2A2 GND 2A3 2A4 3A1 3A2 GND 3A3 3A4 VCC 4A1 4A2 GND 4A3 4A4 3OE description The ’LVT16244B devices are 16-bit buffers and line drivers designed for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. These devices provide true outputs and symmetrical active-low output-enable (OE) inputs. When VCC is between 0 and 1.5-V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5-V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. The SN54LVT16244B is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74LVT16244B is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright 2000, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 FUNCTION TABLE (each 4-bit buffer) INPUTS OE A OUTPUT Y L H H L L L H X Z logic symbol† 1OE 2OE 1 EN1 48 25 3OE 4OE 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 3A1 3A2 3A3 3A4 4A1 4A2 4A3 4A4 24 EN2 EN3 EN4 47 1 1 46 3 44 5 43 6 41 40 1 2 8 9 38 11 37 12 36 13 35 1 3 14 33 16 32 17 30 1 4 19 29 20 27 22 26 23 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 3Y1 3Y2 3Y3 3Y4 4Y1 4Y2 4Y3 4Y4 SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 2OE 2A1 2A2 2A3 2A4 1 3OE 47 2 46 3 44 5 43 6 1Y1 3A1 1Y2 3A2 1Y3 3A3 1Y4 3A4 48 4OE 41 8 40 9 38 11 37 12 2Y1 4A1 2Y2 4A2 2Y3 4A3 2Y4 4A4 25 36 13 35 14 33 16 32 17 3Y1 3Y2 3Y3 3Y4 24 30 19 29 20 27 22 26 23 4Y1 4Y2 4Y3 4Y4 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high state, VO (see Note 1) . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Current into any output in the low state, IO: SN54LVT16244B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74LVT16244B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Current into any output in the high state, IO (see Note 2): SN54LVT16244B . . . . . . . . . . . . . . . . . . . . . 48 mA SN74LVT16244B . . . . . . . . . . . . . . . . . . . . . 64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This current flows only when the output is in the high state and VO > VCC. 3. The package thermal impedance is calculated in accordance with JESD 51. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 recommended operating conditions (see Note 4) SN54LVT16244B SN74LVT16244B MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage 0.8 0.8 Input voltage 5.5 5.5 V IOH IOL High-level output current –24 –32 mA 48 64 mA ∆t/∆v Input transition rise or fall rate 10 10 ns/V ∆t/∆VCC TA Power-up ramp rate 200 Operating free-air temperature –55 High-level input voltage 2 Low-level output current Outputs enabled 2 V –40 V µs/V 200 125 V 85 °C NOTE 4: All unused inputs of the device must at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH II = –18 mA IOH = –100 µA VCC = 2.7 V, IOH = –8 mA IOH = –24 mA VCC = 2 2.7 7V VOL VCC = 3 V II Data inp inputs ts MIN VCC = 2.7 V, VCC = 2.7 V to 3.6 V, VCC = 3 V Control inputs SN54LVT16244B TYP† MAX TEST CONDITIONS VCC = 0 or 3.6 V, VCC = 3.6 V, VCC = 3 3.6 6V SN74LVT16244B TYP† MAX MIN –1.2 VCC–0.2 2.4 –1.2 VCC–0.2 2.4 V V 2 IOH = –32 mA IOL = 100 µA UNIT 2 0.2 0.2 IOL = 24 mA IOL = 16 mA 0.5 0.5 0.4 0.4 IOL = 32 mA IOL = 48 mA 0.5 0.5 V 0.55 IOL = 64 mA VI = 5.5 V 0.55 VI = VCC or GND VI = VCC 50 10 ±1 ±1 1 1 IOZL VI = 0 VCC = 0, VI or VO = 0 to 4.5 V VCC = 3.6 V, VO = 3 V VCC = 3.6 V, VO = 0.5 V –5 –5 µA IOZPU VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don’t care ±100* ± 100 µA IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don’t care ±100* ±100 µA 0.19 0.19 ICC 3 6 V, V IO = 0, 0 VCC = 3.6 VI = VCC or GND Ioff IOZH –5 µA Outputs high Outputs low Outputs disabled ∆ICC‡ VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 –5 ±100 µA 5 5 µA 5 5 0.19 0.19 0.2 0.2 4 Co 9 *On products compliant to MIL-PRF-38535, this parameter is not production tested. † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. mA mA 4 pF 9 pF PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVT16244B PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A Y tPZH tPZL OE Y tPHZ tPLZ OE Y VCC = 3.3 V ± 0.3 V SN74LVT16244B VCC = 2.7 V VCC = 2.7 V MAX MIN TYP† MAX 4.4 4.6 1.2 2.3 3.2 3.7 3.6 3.9 1.2 2 3.2 3.7 1.1 4.6 5.4 1.2 2.6 4 5 1.1 5.4 6.2 1.2 2.7 4 5 1.6 5.7 6.2 2.2 3.3 4.5 5 1.2 5 4.7 2 3.1 4.2 4.4 MIN MAX 1.1 1.1 MIN tsk(o) † All typical values are at VCC = 3.3 V, TA = 25°C. 0.5 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 VCC = 3.3 V ± 0.3 V POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN UNIT MAX ns ns ns ns SN54LVT16244B, SN74LVT16244B 3.3-V ABT 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS716 – MARCH 2000 PARAMETER MEASUREMENT INFORMATION 6V 500 Ω From Output Under Test S1 Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT 1.5 V Timing Input 0V tw tsu 2.7 V 1.5 V Input th 2.7 V 1.5 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION 2.7 V Input 1.5 V 1.5 V 0V tPHL tPLH VOH Output 1.5 V 1.5 V VOL 1.5 V 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V tPZL tPLZ 3V 1.5 V tPZH VOH Output Output Waveform 1 S1 at 6 V (see Note B) tPLH tPHL 2.7 V Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated