SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 D D D D D D 1OE 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 2OE 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 SN54LVTH240 . . . FK PACKAGE (TOP VIEW) 1A2 2Y3 1A3 2Y2 1A4 2OE D SN54LVTH240 . . . J PACKAGE SN74LVTH240A . . . DB, DW, OR PW PACKAGE (TOP VIEW) 2Y4 1A1 1OE VCC D State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC ) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Ioff and Power-Up 3-State Support Hot Insertion Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), and Ceramic (J) DIPs 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y1 2A4 1Y2 2A3 1Y3 2Y1 GND 2A1 1Y4 2A2 D description These octal buffers and line drivers are designed specifically for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices are organized as two 4-bit buffer/line drivers with separate output-enable (OE) inputs. When OE is low, the devices pass data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance state. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. The SN54LVTH240 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74LVTH240A is characterized for operation from –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 FUNCTION TABLE (each 4-bit buffer) INPUTS OUTPUT Y OE A L H L L L H H X Z logic symbol† 1OE 1A1 1A2 1A3 1A4 1 2OE EN 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 19 EN 11 9 13 7 15 5 17 3 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 2 1 2OE 2 18 4 16 6 14 8 12 1Y1 2A1 1Y2 2A2 1Y3 2A3 1Y4 2A4 POST OFFICE BOX 655303 19 11 9 13 7 15 5 17 3 • DALLAS, TEXAS 75265 2Y1 2Y2 2Y3 2Y4 2Y1 2Y2 2Y3 2Y4 SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high state, VO (see Note 1) . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Current into any output in the low state, IO: SN54LVTH240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74LVTH240A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Current into any output in the high state, IO (see Note 2): SN54LVTH240 . . . . . . . . . . . . . . . . . . . . . . . 48 mA SN74LVTH240A . . . . . . . . . . . . . . . . . . . . . . 64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This current flows only when the output is in the high state and VO > VCC. 3. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions (see Note 4) SN54LVTH240 SN74LVTH240A MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage 0.8 0.8 V Input voltage 5.5 5.5 V IOH IOL High-level output current –24 –32 mA Low-level output current 48 64 mA ∆t/∆v Input transition rise or fall rate ∆t/∆VCC TA Power-up ramp rate 200 Operating free-air temperature –55 High-level input voltage 2 Outputs enabled 2 10 V 10 –40 ns/V µs/V 200 125 V 85 °C NOTE 4: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 2.7 V, VCC = 2.7 V to 3.6 V, II = –18 mA IOH = –100 µA VCC = 2.7 V, IOH = –8 mA IOH = –24 mA VCC = 3 V VCC = 2 2.7 7V VOL VCC = 3 V II Control inputs Data inputs Ioff II(hold) ( ) Data inputs VCC = 0 or 3.6 V, VCC = 3.6 V, VCC = 3 3.6 6V –1.2 VCC–0.2 2.4 IOL = 24 mA IOL = 16 mA 0.5 0.5 0.4 0.4 IOL = 32 mA IOL = 48 mA 0.5 0.5 0.55 VI = VCC or GND VI = VCC IOZPU IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don’t care ICC VCC = 3.6 V, IO = 0, VI = VCC or GND V 0.55 IOL = 64 mA VI = 5.5 V VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don’t care V 2 0.2 VI = 0 VCC = 0, VI or VO = 0 to 4.5 V VI = 0.8 V VCC = 3 V VI = 2 V VCC = 3.6 V‡, VI = 0 to 3.6 V UNIT V 2 0.2 VCC = 3.6 V, VCC = 3.6 V, Ci SN74LVTH240A TYP† MAX MIN –1.2 VCC–0.2 2.4 IOH = –32 mA IOL = 100 µA IOZH IOZL ∆ICC§ SN54LVTH240 TYP† MAX MIN 10 10 ±1 ±1 1 1 –5 µA –5 ±100 75 75 –75 –75 µA µA ±500 VO = 3 V VO = 0.5 V Outputs high Outputs low Outputs disabled VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND VI = 3 V or 0 3 Co 5 5 µA –5 –5 µA ±100∗ ±100 µA ±100∗ ±100 µA 0.19 0.19 5 5 0.19 0.19 0.2 0.2 3 mA mA pF VO = 3 V or 0 7 7 pF ∗ On products compliant to MIL-PRF-38535, this parameter is not production tested. † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVTH240 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A Y tPZH tPZL OE Y tPHZ tPLZ OE Y VCC = 3.3 V ± 0.3 V SN74LVTH240A VCC = 2.7 V VCC = 3.3 V ± 0.3 V VCC = 2.7 V MAX MIN TYP† MAX 4.3 5.1 1.1 2.2 3.8 4.6 1.2 4.7 4.9 1.3 2.6 4 4.2 MIN MAX 0.9 MIN MIN UNIT MAX 1 5.7 6.7 1.1 2.6 4.6 5.6 1.2 5.5 6.2 1.4 2.7 4.4 5 1 5.1 5.2 2 2.9 4.4 4.6 1.1 5.4 5.4 1.8 3 4.3 4.3 ns ns ns † All typical values are at VCC = 3.3 V, TA = 25°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54LVTH240, SN74LVTH240A 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS679F – DECEMBER 1996 – REVISED MARCH 2000 PARAMETER MEASUREMENT INFORMATION 6V 500 Ω From Output Under Test Open S1 GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 2.7 V Input 1.5 V 1.5 V th 2.7 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 2.7 V 1.5 V Input 1.5 V 0V VOH Output 1.5 V 1.5 V VOL 1.5 V tPLZ 3V 1.5 V tPZH VOH Output 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V Output Waveform 1 S1 at 6 V (see Note B) tPLH tPHL 1.5 V tPZL tPHL tPLH 2.7 V Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated