SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 D D D D D D OE1 A1 A2 A3 A4 A5 A6 A7 A8 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC OE2 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 SN54LVTH540 . . . FK PACKAGE (TOP VIEW) A3 A4 A5 A6 A7 OE2 D SN54LVTH540 . . . J OR W PACKAGE SN74LVTH540 . . . DB, DW, OR PW PACKAGE (TOP VIEW) A2 A1 OE1 VCC D State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation Ioff and Power-Up 3-State Support Hot Insertion Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25°C Latch-Up Performance Exceeds 500 mA Per JESD 17 ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), Ceramic Flat (W) Package, and Ceramic (J) DIPs 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 Y1 Y2 Y3 Y4 Y5 A8 GND Y8 Y7 Y6 D description These octal buffers/drivers are designed specifically for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. The ’LVTH540 devices are ideal for driving bus lines or buffer memory address registers. These devices feature inputs and outputs on opposite sides of the package that facilitate printed circuit board layout. The 3-state control gate is a 2-input AND gate with active-low inputs so that if either output-enable (OE1 or OE2) input is high, all outputs are in the high-impedance state. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1999, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 description (continued) The SN54LVTH540 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74LVTH540 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUTS A OUTPUT Y L L H L H L OE1 OE2 L L H X X Z X H X Z logic symbol† OE1 1 & 19 EN OE2 A1 A2 A3 A4 A5 A6 A7 A8 2 18 1 3 17 4 16 5 15 6 14 7 13 8 12 9 11 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) OE1 OE2 A1 1 19 2 18 To Seven Other Channels 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Y1 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high state, VO (see Note 1) . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Current into any output in the low state, IO: SN54LVTH540 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74LVTH540 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Current into any output in the high state, IO (see Note 2): SN54LVTH540 . . . . . . . . . . . . . . . . . . . . . . . 48 mA SN74LVTH540 . . . . . . . . . . . . . . . . . . . . . . . 64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This current flows only when the output is in the high state and VO > VCC. 3. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions (see Note 4) SN54LVTH540 SN74LVTH540 MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage 0.8 0.8 V Input voltage 5.5 5.5 V IOH IOL High-level output current –24 –32 mA Low-level output current 48 64 mA ∆t/∆v Input transition rise or fall rate ∆t/∆VCC TA Power-up ramp rate 200 Operating free-air temperature –55 High-level input voltage 2 2 10 V 10 –40 ns/V µs/V 200 125 V 85 °C NOTE 4: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH VCC = 2.7 V, VCC = 2.7 V to 3.6 V, II = –18 mA IOH = –100 µA VCC = 2.7 V, IOH = –8 mA IOH = –24 mA VCC = 3 V 7V VCC = 2 2.7 VOL VCC = 3 V II Control inputs Data inputs inp ts Ioff II(hold) ( ) VCC = 0 or 3.6 V, VCC = 3.6 V, VCC = 3 3.6 6V VCC = 0, Data inputs VCC = 3 V VCC = 3.6 V‡, IOZH IOZL SN54LVTH540 TYP† MAX TEST CONDITIONS VCC = 3.6 V, VCC = 3.6 V, MIN SN74LVTH540 TYP† MAX MIN –1.2 VCC–0.2 2.4 –1.2 VCC–0.2 2.4 V V 2 IOH = –32 mA IOL = 100 µA UNIT 2 0.2 0.2 IOL = 24 mA IOL = 16 mA 0.5 0.5 0.4 0.4 IOL = 32 mA IOL = 48 mA 0.5 0.5 0.55 IOL = 64 mA VI = 5.5 V 10 10 VI = VCC or GND VI = VCC ±1 ±1 1 1 VI = 0 VI or VO = 0 to 4.5 V –5 –5 V 0.55 VI = 0.8 V VI = 2 V ±100 75 75 –75 –75 µA µA µA ±500 VI = 0 to 3.6 V VO = 3 V IOZPU VO = 0.5 V VCC = 0 to 1.5 V, VO = 0.5 V to 3 V, OE = don’t care IOZPD VCC = 1.5 V to 0, VO = 0.5 V to 3 V, OE = don’t care ICC VCC = 3.6 V, IO = 0, VI = VCC or GND ∆ICC§ VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 Outputs high Outputs low Outputs disabled 3 5 5 µA –5 –5 µA ±100∗ ± 100 µA ±100∗ ±100 µA 0.19 0.19 5 5 0.19 0.19 0.2 0.2 3 mA mA pF Co 7 7 pF ∗ On products compliant to MIL-PRF-38535, this parameter is not production tested. † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVTH540 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A Y tPZH tPZL OE1 or OE2 Y tPHZ tPLZ OE1 or OE2 Y VCC = 3.3 V ± 0.3 V SN74LVTH540 VCC = 2.7 V VCC = 3.3 V ± 0.3 V VCC = 2.7 V MAX MIN TYP† MAX 3.9 4.7 1.1 2.4 3.8 4.6 1 3.9 4.7 1.1 2.7 3.8 4.6 1.4 5.3 6.3 1.5 3.4 5.2 6.2 1.4 5.5 6.1 1.5 3.7 5.3 5.9 1.4 5.9 6.2 1.5 3.9 5.6 5.9 1.4 5.5 5.8 1.5 3.5 5 5.3 MIN MAX 1 MIN MIN UNIT MAX ns ns ns † All typical values are at VCC = 3.3 V, TA = 25°C. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54LVTH540, SN74LVTH540 3.3-V ABT OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCBS681E – MARCH 1997 – REVISED APRIL 1999 PARAMETER MEASUREMENT INFORMATION 500 Ω From Output Under Test 6V Open S1 GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPHL/tPLH tPLZ/tPZL tPHZ/tPZH Open 6V GND 2.7 V LOAD CIRCUIT Timing Input 1.5 V 0V tw tsu 2.7 V 1.5 V Input 1.5 V th 2.7 V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 2.7 V 1.5 V Input 1.5 V 0V tPLH tPHL VOH 1.5 V Output 1.5 V VOL tPHL Output Waveform 1 S1 at 6 V (see Note B) 1.5 V 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V tPZL tPLZ 3V 1.5 V tPZH tPLH VOH Output 2.7 V Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated