HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
DESCRIPTION
HB7122B is a highly integrated single chip CMOS B/W image sensor using Hyundai 0.5um CMOS process
developed for image application to realize high efficiency photo sensor. The sensor has 414X314 pixels total,
and 400X300 pixels effective. Each pixel is high photo sensitive, small size active pixel element that converts
photons to analog voltage signal. The sensor has three on-chip 8 bit Digital to Analog Convert (DAC) and 414
comparators to digitize the pixel output. The three on-chip 8 bit DAC can be used for independent gain
control. Hyundai proprietary on-chip Correlated Double Sampling (CDS) circuit can reduce Fixed Pattern
Noise (FPN) dramatically. The whole 8 bit digital B/W raw data is directly available on the package pins and
just a few control signals are needed for whole chip control, so it is very ease to configure a system using the
sensor.
FEATURES
400 x 300 pixels resolution
8um x 8um square pixel
High efficiency photo sensors
Integrated 8-bit ADC for direct digital output
Low power 3.3V operation (5V tolerant I/O)
Integrated pan control and window sizing
Clock speed up to 15MHz
Programmable frame rate and synchronous format
l
l
l
l
l
l
l
FUNCTIONAL BLOCK DIAGRAM
Pixel resolution
402x302
Pixel size
8x8um2
Fill factor
30%
Format
CIF
Sensitivity
8.0V/luxžsec
Supply voltage for analog
3.3V
Supply voltage for digital
3.3V
Supply voltage for 5V tolerant input
5.0V
Power Consumption
Operating temperature
Technology
I2C
Decoder/Pixel Driver
TECHNICAL SPECIFICATION
Full function control through standard I2C bus
Built-in Automatic Gain Control (AGC)
48 pin CLCC
Anti-blooming circuit
Flexible exposure time control
Integrated on-chip timing and drive control
1/4" optical format
Control Register & Logic
l
l
l
l
l
l
l
l
Pixel Array
ADC Block
TBD@15MHz
Line Buffer
0~40 Centigrade
0.5um 3metal CMOS
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-1-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
l
Supply voltage(Analog, Digital)
:
-0.4 V
~
3.8 V
l
Voltage on any input pins
:
-0.4 V
~
VDD + 0.5 V
l
Operating Temperature(Centigrade)
:
0
~
40
l
Storage Temperature(Centigrade)
:
-30
~
80
Note : Input pins are 5V tolerant. Stresses exceeding the absolute maximum ratings may induce failure.
DC Operating Conditions
Symbol
Parameter
Units
Min.
Max.
Load[pF]
Vdd
Internal operation supply voltage
Volt
3.0
3.6
Vih
Input voltage logic "1"
Volt
2.0
5
6.5
Vil
Input voltage logic "0"
Volt
0
0.8
6.5
Voh
Output voltage logic "1"
Volt
2.15
3.6
60
Vol
Output voltage logic "0"
Volt
0.4
0.4
60
Ta
Ambient operating temperature
Celsius
0
40
Notes
AC Operating Conditions
Symbol
Parameter
Max Operation Frequency
Units
Notes
MCLK
Main clock frequency
20
MHz
1
400
KHz
2
SCK
2
I C clock frequency
1. MCLK can be divided according to Clock Divide Register for internal clock.
2. SCK is driven by host processor. For the detail serial bus timing, refer to I2C Spec.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-2-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
ELECTRO-OPTICAL CHARACTERISTICS
color temperature of light source: 3200K / IR cut-off filter (CM-500S, 1mmt) is used.
Parameter
Units
Sensitivity
mV / luxžsec
Dark Signal
mV/sec
Output Saturation Signal
mV
Dynamic Range
dB
Output Signal Shading
%
Dark Signal Shading
Frame Rate
Min.
Typical
Max.
8000
Note
1)
50
1200
2)
3)
48
4)
13
5)
mV/sec
10
6)
fps
60
7)
8
Note:
1) Measured at 8lux illumination for exposure time 10 ms.
2) Measured at zero illumination for exposure time 50 ms. (Ttemp = 40 Centigrade)
3) Measured at Vdd =3.3V and 100lux illumination for exposure time 50msec.
4) 48dB is limited by 8-bit ADC.
5) Variance of average value of 4x4 pixels response of each block over all equal blacks at 50%
saturation level illumination for exposure time 10msec.
6) Range between Vmax and Vmin at zero illumination for exposure time 50msec, where Vmax and Vmin
are the maximum and minimum values of each block’ s response, respectively.
7) Measured at MCLK 15MHz.
Integration time must be set in order for effective window height not to exceed window height.
It’ s because effective window height is directly proportional to integration time.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-3-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
INPUT / OUTPUT AC CHARACTERISTICS
l
All output timing delays are measured with output load 60[pF].
l
Output delay include the internal clock path delay 6[ns] and output driving delay that changes in
respect to the output load, the operating environment, and a board design.
l
Due to the variable valid time delay of the output, output signals may be latched in the negative
edge of MCLK for the stable data transfer between the image sensor and a host for less than
15MHz operation.
MCLK to HSYNC/VSYNC Timing
T1
T1
MCLK
HSYNC/VSYNC
T2
T1 : MCLK rising to HSYNC/VSYNC valid maximum time : 18ns [output load: 60pF]
T2 : HSYNC/VSYNC valid time : minimum 1clock(subject to T1, T2 timing rule)
MCLK to DATA Timing
T3
T3
MCLK
DATA[7:0]
valid data
T3 : MCLK rising to DATA valid maximum time : 18ns [output load: 60pF]
Note) HSYNC signal is high when valid data is on the DATA bus.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-4-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
INPUT / OUTPUT AC CHARACTERISTICS (Continue)
ENB Timing
T4
T5
MCLK
T6
ENB
T
T4 : ENB Setup Time : 5[ns]
T5 : ENB Hold Time : 5[ns]
T6 : ENB valid Time : minimum 2 clock
RESET Timing
Must in Valid (active low) state at least 8 MCLK periods
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-5-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
INPUT
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
/ OUTPUT AC CHARACTERISTICS CONTINUE
I2C Bus (Programming Serial Bus) Timing
stop
start
start
stop
SDA
tr
tf
tbuf
thd;sta
tlow
SCK
thd;sta
thd;dat
thigh
tsu;dat
tsu;sta
tsu;sto
I2C Bus Interface Timing
Parameter
Symbol
Min.
Max.
Unit
SCK clock frequency
fsck
0
400
KHz
Time that I2C bus must be free before a new
transmission can start
tbuf
1.2
us
Hold time for a START
LOW period of SCK
thd;sta
tlow
1.0
1.2
us
us
HIGH period of SCK
thigh
1.0
us
Setup time for START
Data hold time
tsu;sta
thd;dat
1.2
1.3
us
us
Data setup time
tsu;dat
250
ns
Rise time of both SDA and SCK
tr
250
ns
Fall time of both SDA and SCK
tf
300
ns
Setup time for STOP
Capacitive load of each bus lines(SDA,SCK)
tsu;sto
Cb
1.2
us
pf
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-6-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
PIN CONFIGURATION (48 pin CLCC)
PIN NO.
1
2
3
4
5
6
7
8
17
18
21
22
23
24
25
NAME
SCK
DGND
ENB
DGND
MCLK
VDD5
AVDD
AGND
AGND
AVDD
DGND
DATA7
DATA6
DATA5
DATA4
PIN NO.
26
27
28
29
30
31
32
42
43
44
45
46
47
48
NAME
DGND
DATA3
DATA2
DATA1
DATA0
DVDD
DGND
DVDD
RESET
VSYNC
HSYNC
DGND
SDA
DGND
Pin9~16, Pin19~20, Pin33~41 : No Connection
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any
responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-7-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
PIN DESCRIPTIONS (48 Pin CLCC)
PIN
NAME
I/O
1
2
3
SCK
DGND
ENB
I
I
I
4
5
DGND
MCLK
I
I
6
7
8
9 ~ 16
17
18
19, 20
21
22
23
24
25
26
27
28
29
30
31
32
33 ~ 41
42
43
44
VDD5
AVDD
AGND
N.C
AGND
AVDD
Reserved
DGND
DATA7
DATA6
DATA5
DATA4
DGND
DATA3
DATA2
DATA1
DATA0
DVDD
DGND
N.C
DVDD
RESET
VSYNC
I
I
I
45
HSYNC
/DVALID
DGND
SDA
DGND
46
47
48
I
I
I
O
O
O
O
I
O
O
O
O
I
I
I
I
O
O
I
I/O
I
DESCRIPTION
I2C Clock ; I2C clock control from I2C master
Digital Ground
Sensor Enable Signal ; 'H' enable normal operation
'L' disable sensor
Digital Ground
Master Clock (up to 15MHz)
; Global master clock for image sensor internal timing control
I/O bias voltage for 5V tolerant *1)
Analog Supply Voltage 3.3V
Analog Ground
No Connection
Analog Ground
Analog Supply Voltage 3.3V
Reserved
Digital Ground
Image Data bit 7
Image Data bit 6
Image Data bit 5
Image Data bit 4
Digital Ground
Image Data bit 3
Image Data bit 2
Image Data bit 1
Image Data bit 0
Digital Supply Voltage 3.3V
Digital Ground
No Connection
Digital Supply Voltage 3.3V
Hardware Reset Signal, Active Low
Vertical synchronization signal / Frame start output
; Signal pulse at start of image data frame with programmable
blanking duration
Horizontal synchronization signal / Data valid output
; Data valid when 'H' with programmable blanking duration
Digital Ground
I2C Data ; I2C standard data I/O port
Digital Ground
*1) Tie to DVDD for 3.3V operation / Tie to 5V for 5V tolerant operation
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-8-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Register map
Register Name
address
7
6
5
4
3
2
Mode A
00h
Mode B
01h
Mode C
02h
Row Start Address High
10h
Row Start Address Low
11h
Column Start Address High
12h
Column Start Address Low
13h
Window Height Address High
14h
Window Height Address Low
15h
Window Width Address High
16h
Window Width Address Low
17h
w_ad[7:0]
HSYNC Blanking Time High
20h
h_blank[15:8]
HSYNC Blanking Time Low
21h
h_blank[7:0]
VSYNC Blanking Time High
22h
v_blank[15:8]
VSYNC Blanking Time Low
23h
v_blank[7:0]
Integration Time High
25h
int_time[23:16]
Integration Time Middle
26h
int_time[15:8]
Integration Time Low
27h
int_time[7:0]
Master Clock Divider
28h
Reset Level Control
30h
Red Color Gain
31h
reserved
red_color[5:0]
Green Color Gain
32h
reserved
green_color[5:0]
Blue Color Gain
33h
reserved
blue_color[5:0]
Pixel Bias Voltage
34h
Red Offset Gain Control
50h
reserved
red_offset[6:0]
Green Offset Gain Control
51h
reserved
green_offset[6:0]
Blue Offset Gain Control
52h
reserved
blue_offset[6:0]
Low Reference Number High
57h
low_ref_no[15:8]
Low Reference Number Low
58h
low_ref_no[7:0]
High Reference Number High
59h
high_ref_no[15:8]
High Reference Number Low
5Ah
high_ref_no[7:0]
model_name
oper_mode
1
0
rev_num
data_type
reserved
hs_out
scr_size
shot
int_sel
sw_enb
pwr_dn
color
reserved
reserved
r_ad[8]
r_ad[7:0]
reserved
c_ad[8]
c_ad[7:0]
reserved
h_ad[8]
h_ad[7:0]
reserved
w_ad[8]
reserved
clk_div[3:0]
rst_level[5:0]
reserved
pixel_bias[3:0]
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
-9-
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Register Set Descriptions
All register access can though the I2C multi-byte read and write.
(1) Mode A Register (Address 00h, RO)
This register consist of a model name and revision number. The upper 4 bits is model_name [3:0] and
the lower 4 bits is rev_num[3:0]. For example it’ s value 12h, this mean 400*300 resolution and
revision2.0 chip.
< model_name >
400*300 : 0001b
< rev_num >
Rev. 2.0 : 0010b
(2) Mode B Register (Address 01h, default : 04h, R/W)
This register defines major operation mode of the chip.
n
Mode B[7:6] : oper_mode(operating mode) <default value : 00b>
Define operating modes between normal operation and optical and function test operation.
Test operation mode is used for optical and function test. Except for default value, these bits
are reserved for manufacturer.
Bit
00
01
10
11
operating mode
Normal operation
Reserved
Reserved
Reserved
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 10 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
n
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Mode B [5:4] : data_type(data types) <default value : 00b>
These bits define output pixel data types. For Correlated Double Sampling(CDS), every the
pixel of image sensor are measured twice, reference and data respectively, and reference
values or data values can be read out through pixel data pins selectively using these control
bits. To remove the noise caused by circuit, i.e. Fixed Pattern Noise, the image sensor
performs the CDS in default value. Three output data types are supported as follows.
Bit
00
01
10
11
n
Output data type
Data level - Reference level
Reference level
Data level
Reserved
Mode B[3] : hs_out(HSYNC output configuration) <default value : 0b>
This bit offers two types output style about HSYNC signal. HSYNC only mode and HSYNC &
internal clock mode. If the hs_out is set to one, HSYNC output signal is ANDed signal of
internal pixel clock and data valid. Otherwise HSYNC output pin keep data high state during
valid output period. When HSYNC & internal clock mode is set, HSYNC output can be used
as a pixel data output clock.
data valid
MUX
HSYNC
pixel clock
Mode B[3]
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 11 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
n
Mode B[2]
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
: scr_size(screen size select) <default value : 1b>
Flexible screen size is very useful for customer. If the scr_size is set to high, i.e. window
mode, only pixels in windowed area defined by register 10h ~ 17h can be read . But scr_size
is set to low state, i.e. full screen mode, all pixels in the sensor are read out regardless the
values of register 10h ~ 17h. We can select window mode or full screen mode with this bit. Full
screen size is only for chip test.
- window start point :
x : row start address (register 10h, 11h)
y : column start address (register 12h, 13h)
- window end point :
x : row start address + window width address (register 14h, 15h) - 1
y : column start address + window height address (register 16h, 17h) –1
n
Mode B [1] : shot(shot mode) <default value : 0b>
User can select continuous frame mode or snapshot mode according to application.
At the continuous frame mode, pixel data output is updated every VSYNC period. In order to
set snapshot mode, it this bit to ‘ 1’ . In that case, just single frame of pixel data will be read out,
then the sensor stops operation. Snapshot mode can be used for the digital still camera
applications.
n
Mode B[0] : int_sel(integration time unit select) <default value : 0b>
This bit defines integration time unit i.e. line base or pixel clock base.
Default mode is line unit integration but at the bright condition or if you need precise exposure
time control, pixel mode is recommended. This bit related to integration time register 25h, 26h,
and 27h.
<Note>
Actual integration time can be calculated using three integration time registers and pixel clock
period.
In pixel mode, integration time = (25h, 26h, 27h) * number of pixel period.
In line mode, integration time = (26h, 27h) * number of pixel per line * pixel period.
(cf) number of pixel per line = 414 + HSYNC duration value
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 12 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
(3) Mode C Register (Address 02h, default : 08h, R/W)
This register controls power down and color select.
n
Mode C[3] :
sw_enb (software enable : active low)
(400*300 CMOS image sensor only)
<default value : 1b>
This bit is only exist in 400*300 CMOS image sensor chip to enable image sensor operation
by software. This bit has same function as ENB pin control.
It’ s very useful for the applications that is needed want to reduce interface pin count to
CMOS image sensor. In that case, cannot ENB pin to VDD line and control the sensor using
this bit.
n
Mode C[2] :
pwr_dn(A/D converter power down) <default value : 0b>
This bit controls power down of A/D converter when sleep mode(idle state) is set by ENB pin
is low or sw_enb(Mode C[3]) is high. When set to high, A/D converter is turned on whenever
ENB is low or sw_enb is high. When set to low, A/D converter is turned off always regardless
ENB pin state or sw_enb state . But digital block goes to power down mode always when
ENB is low regardless this bit.
n
Mode C[1] :
color(color select) <default value : 0b>
This bit selects color mode or monochrome mode. Default value means color image sensor
and all three ADCs are used for Bayer RGB color pattern respectively, then RGB gains are
controlled independently. But when set this to one, i.e. monochrome mode, just single ADC is
used for all pixels regardless RGB color.
At the monochrome mode all pixels are controlled by ‘ G’ gain only. ‘ R’ and ‘ B’ gain are not
used. In case of monochrome image sensor, this bit should be set to ‘ 1’ get the good image
and to simplify the sensor control.
(4) Row start address Register
(Higher byte : Address 10h, default : 00h, R/W)
(Lower byte : Address 11h, default : 06h, R/W)
Define window start position row start address of display window. Should be programmed with
value between 6 and 306.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 13 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
(5) Column start address Register
(Higher byte : Address 12h, default : 00h, R/W)
(Lower byte : Address 13h, default : 06h, R/W)
Define window start position column address of display window. Should be programmed with value
between 6 and 406.
(6) Window Height address Register
(Higher byte : Address 14h, default : 01h, R/W)
(Lower byte : Address 15h, default : 2Eh, R/W)
Define display window height. If you need smaller display window height, decrease the value.
Window end position row address = row start address + window height address –1
(7) Window width address Register
(Higher byte : Address 16h, default : 01h, R/W)
(Lower byte : Address 17h, default : 92h, R/W)
Define display window width. If you need smaller display window width, decrease the value.
Window end position column address = column start address + window width address -1
Note : Display window programming.
< Display Window Programming >
The 400*300 resolution chip can read any user specific window area within active window area.
This is called panning function. For this function, ‘ row start’ , ‘ column start’ , ‘ width’ , and ‘ height’
can be programmed with four sets of register pair.
n
FRS :
Frame Row Start
n
FCS :
Frame Column Start
n
FWH :
Frame window Height
n
FWW :
Frame Window Width
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 14 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Panning window can be programmed as below.
(413,313)
(0,313)
(407,307)
manufacturer area
active window area
{FRSU, FRSL}
{FWWU, FWWL}
{FCSU, FCSL}
(6,6)
(413,0)
(0,0)
Note 1) Accessible pixel array size is 402*302.
The edge of accessible pixel array may be commonly dedicated for just color interpolation.
In the case of a color image sensor the interpolation is needed to get all R,G,B color value for
each pixel from a Bayer color image.
So one more extra pixel line is needed at the edge of pixel array that you want to be displayed.
That is, to make 400*300 effective window, 402*302 pixel array necessary.
You have to consider this interpolation line when you program the ‘ Frame register’ .
For example, if you want to get 300*250 image size, you have to program 302*252 to frame
register.
<Default window area>
FRSU, FRSL
6
FWHU, FWHL
302
FCSU, FCSL
6
FWWU, FWWL
402
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 15 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
< Pixel Array Structure >
total pixel : 416 * 316
+1 : dummy area
+1 : dummy zone for set of color pattern
+2 : optical block zone
+3 : margin for metal 3 slope
+1 : interpolation area
pixel array : 400 * 300
---- R G
G B G B
----
R G
B G
G R
active window area (402 * 302)
accessible address range(414 * 314)
(8) HSYNC Blanking Time Register
(Higher byte : Address 20h, default : 00h, R/W)
(Lower byte : Address 21h, default : 03h, R/W)
The HSYNC blanking time defines HSYNC low duration between data valid HSYNC high, pixel unit .
HSYNC low duration is HSYNC blanking time plus twelve in pixel unit for example, default HSYNC
low duration is 15 pixels because register value is 3.
It’ s used to change duration between current line end and next line start.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 16 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
(9) VSYNC Blanking Time Register
(Higher byte : Address 22h, default : 00h, R/W)
(Lower byte : Address 23h, default : 03h, R/W)
The VSYNC blank, and time defines VSYNC active duration in pixel unit .
<Note>
HSYNC blanking, VSYNC blank are used to fit the CMOS sensor display timing to external timing
requirements.
(10) Integration time Register
(High
byte : Address 25h, default : 00h, R/W)
(Middle byte : Address 26h, default : 01h, R/W)
(Low
byte : Address 27h, default : f4h, R/W)
Each pixel has a photo diode in which the incoming photons are converted to electrons. Integration
time mean exposure time so these registers defines exposure time.
According to settings int_sel of Mode B register, the integration time is controlled with line or pixel
unit. Small value means short exposure time and large value means long exposure time for bright
condition.
The value should be large for dark condition. Default value setting 500 lines, this value is useful for
normal office condition. If you stay in outdoor condition, this value should be decreased. But under
dark condition, this value should be increased to get a good image quality. Increasing value may
decrease frame rate. Finally, integration time is very important for frame rate and image quality.
For line mode exposure, register 26h and 27h are used. For pixel mode exposure, all three register
25h ~ 27h are used. To control exposure time precisely, the pixel mode should be used. This register
may be used for Auto Exposure control.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 17 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
(11) Operating Clock Divider (Address 28h, default:00h, R/W)
This register generates divided digital clock depending on the settings clk_div [3:0], digital block can
divide MCLK down by 1 through 2048 as shown in Table 1.
clk_div[3:0]
0000
0001
0010
0011
0100
0101
units
no division
MCLK/2
MCLK/4
MCLK/8
MCLK/16
MCLK/32
clk_div[3:0]
0101
0111
1000
1001
1010
1011
units
MCLK/64
MCLK/128
MCLK/256
MCLK/512
MCLK/1024
MCLK/2048
Table 1. Operating Clock Control Register
(12) Reset Level Control Register (Address 30h, default:38h, R/W)
This register controls reference voltage level for start point of data reading. If the register value is
too large or too small, the vertical Fixed Pattern Noise(FPN) can be occurred. To Get rid of FPN,
this register must have a suitable value. Optimum reset revel can be found using Low reference
number registers 57h ~ 58h and High reference number registers 59h ~ 5ah. If there is some large
value in Low reference number registers, the value of Reset Level control register should be
increased. If there is some large value in High reference number registers, the value of register
should be decrease. Optimum reset revel is achieved when value of Low reference level number
registers and value of High reference number registers is minimized.
(13) Color Gain Register
Red Color Gain Register
: (Address 31h, default:1Eh, R/W)
Green Color Gain Register : (Address 32h, default:h1Eh, R/W)
Blue Color Gain Register : (Address 33h, default:h1Eh, R/W)
These registers are used to amplify the analog pixel output. If the gain register value is decreased,
the amplification is increased. Therefore under the dark light source condition, the pixel output have
to be amplified by decreasing gain value to get good image. There are three Gain registers to control
RGB colors independently. In the case of monochrome image sensor, use only Green Color Gain
Register. Available program range is 0 ~ 63 but too small value can cause FPN. The register value
have to chosen within the range that doesn’ t cause FPN. Recommended range is 20 ~63. These
register can be used for Auto White Balance control and Auto Exposure control.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 18 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
(14) Pixel Bias Voltage Register (Address 34h, default:02h, R/W)
This register controls pixel reference level by controlling bias current of pixel output sensing load
transistor. It controls pixel output level itself, compare with that revel register adjust A/D Converter
circuit to calibrate reference level for data reading. Available program range is 0 ~ 7. The larger
register value causes the higher bias current and low pixel output reference level. This register is
option for manufacturer. Users may use default setting and don’ t changed value.
(15) Low Reference Number Register(low_ref_no)
High : (Address 57h default:00h, Read Only)
Low : (Address 58h, default:00h, Read Only)
Low Reference Number Registers indicates number of pixels in frame that have a value less then 5.
A reference level values of each pixel is compare with ‘ 5’ , and accumulated to these registers
during read state. This counter value called low_ref_no, consist of two bytes and it is read only
registers. Real number of pixels that have value less than 5 is the twice of these register value. If
low_ref_no is big value, you must increase data value of Reset Level Control Register. These
registers are updated after every VSYNC signal.
(16) High Reference Number Register (high_ref_no)
High : (Address 59h, default:00h, Read Only)
Low : (Address 5Ah, default:00h, Read Only)
High Reference Number Registers indicates number of pixels in a frame that have a value great then
123. Reference level values of each pixels is compared with ‘ 123’ , and accumulated to these
registers during read state. This counter value called high_ref_no, consist of two bytes and it is read
only registers. Real number of pixels that have value great than 123 is the twice of these register
value. If high_ref_no is big value, you must decrease data value of Reset Level Control Register.
These registers are also updated after every VSYNC signal.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 19 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
FRAME TIMING DIAGRAMS
There are two frame timing cases,
l
Integration Time < EffectiveWindowHeight * Scale
l
Integration Time > EffectiveWindowHeight * Scale
EffectiveWindowHeight is equal to the number of data lines generated in a frame and is defined to be
selected by
if((RowStartAddress + WindowHeight + 1) <= (SensorArrayHeight)
EffectiveWindowHeight = WindowHeight;
else
EffectiveWidnowHeight = (SensorArrayHeight - RowStartAddress - 1);
For example, RowStartAddress = 200 and WindowHeight = 300, EffectiveWindowHeight is 113 and 113
data lines per a frame are generated.
Note : The above selection logic is somewhat confusing in respect of general counting measure. It’ s partly
due to the mixed use of indexing start points, i.e. ‘ 0’ and ‘ 1’ in the design. Therefore in order to avoid the
confusion it is desirable to just follows the equation when you estimate the frame rate.
SensorArrayWidth
[414]
(0,0)
SensorArrayHeight
[314]
EffectiveWindowHeight
[113]
RowStartAddress
[200]
WindowHeight
[300]
Scale is selected according to Integration Time Mode by
If(PixelMode)
Scale = SensorArrayWidth; // For400*300 resolution chip, SensorArrayWidth is 414
else
Scale = 1;
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 20 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
When Integration Time > (EffectiveWindowHeight * Scale), next frame VSYNC does not follow immediately
after current frame’ s last line has been produced. Instead, one of the following two idle time slots is inserted
according to Integration Time Mode before next frame VSYNC gets active.
< Idle Slots >
l
Line Mode: (Integration Time - EffectiveWindowHeight) * 1024 clocks
l
Pixel Mode: (Integration Time - EffectiveWindowHeigth * Scale)
= (Integration Time - EffectiveWindowHeigth * SensorArrayWidth) clocks
Each Frame Timing of the above cases may be decomposed into four timing segments
l
Initial Data Setup Time after ENB gets active
l
Even Line
l
Odd Line
l
Frame Transition
The subsections will describe frame timing diagram for said frame time cases, (Integration Time < Effective Window
Height * Scale) and (Integration Time > Effective Window Height * Scale)
(1) Frame Timing Diagram for Integration Time < (EffectiveWindowHeight * Scale)
Frame timing related registers are programmed to suit for the above condition as follows
RowStartAddress
= 6;
WindowHeight = 302;
ColumnStartAddress = 6;
WindowWidth = 402;
IntegrationTime = 200 [Line Mode];
EffectiveWindowHeight is “302” for (SensorArrayHeight > (RowStartAddress + WindowHeight + 1)), i.e. 314 >
(6 + 302 + 1), is met, and Scale is “1” for integration time is line mode.
Therefore, (Integration Time< EffectiveWindowHeight * Scale), i.e. 200 < 302 * 1, is met.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 21 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Overall Frames Sequence
Frame 0
Frame 1
....
....
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Initial Data Setup Time
....
Frame 2
....
MCLK
ENB
VSYNC
Delay
ENB+
Deglitch
2 clocks
Sensor Reset
SensorArrayHeight clocks
[314 clocks]
Integration Time *
Scale clocks
[200 * 414 clocks]
Slots
One Line Time Delay
(SensorArrayWidth +
HBLANK) clocks
[417 clocks]
VSYNC
3 clocks
Fig. 1 Initial Data Setup Time after ENB gets active
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 22 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
MCLK
HSYNC
B
G
B
G
DATA
Time
Slot
Line Head
Blank
12 clocks
⋅⋅⋅⋅⋅⋅⋅⋅⋅
B⋅
G
B
G
Line Tail
Blank
12 clocks
IMAGE RAW DATA
Window Width
804 clocks
HBLANK
3 clocks
Clock
SensorArrayWidth (828)
Ruler
HBLANK(3)
Fig.2 Even Line Data Timing
MCLK
HSYNC
G
DATA
Time
Slot
Line Head
Blank
12 clocks
R
G
R
⋅⋅⋅⋅⋅⋅⋅⋅⋅
G⋅
R
IMAGE RAW DATA
Window Width
804 clocks
G
R
Line Tail
Blank
12 clocks
HBLANK
3 clocks
Clock
Ruler
SensorArrayWidth (828)
HBLANK(3)
Fig.3 Odd Line Data Timing
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 23 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
MCLK
HSYNC
VSYNC
.....
DATA
Time
Slot
≈
G
B
R
IMAGE RAW DATA
Window Width
804 clocks
Line Tail
Blank
12 clocks
HBLANK
3 clocks
VSYNC
3 clocks
Line Head
Blank
12 clocks
G
B
.......
IMAGE RAW DATA
Window Width
804 clocks
≈
Integration Time < EffectiveWindowHeight * Scale
Fig.4 Frame Transition Timing
(2) Frame Timing Diagram for Integration Time > (EffectiveWindowHeight * Scale)
Frame timing related registers are programmed to suit for the above condition as follows
RowStartAddress
= 6;
WindowHeight = 302;
ColumnStartAddress = 6;
WindowWidth = 402;
IntegrationTime = 600 [Line Mode];
EffectiveWindowHeight is “302” for (SensorArrayHeight > (RowStartAddress + WindowHeight + 1)),
i.e. 314 > (6 + 302 + 1), is met, and Scale is “1” for integration time is line mode. Therefore,
(Integration Time < EffectiveWindowHeight * Scale), i.e. 600 > 302 * 1, is met, and Idle Slot of Line
Mode, i.e. (600 - 302) * 1024 clocks idle slot, is inserted before the next frame initiation.
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 24 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
Overall Frames Sequence
Frame 0
Frame 1
Frame 2
Idle Time
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Idle Time
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Idle Time
Line 301
Line 300
Line 2
Line 1
Line 0
VSYNC
Initial Data Setup Time
....
....
....
MCLK
ENB
VSYNC
Delay
ENB
Deglitch
2 clocks
Sensor Reset
SensorArrayHeight clocks
[314 clocks]
Integration Time *
Scale clocks
[600 * 414 clocks]
Slots
One Line Time Delay
(SensorArrayWidth +
HBLANK) clocks
[417 clocks]
VSYNC
3 clocks
Fig. 5 Initial Data Setup Time after ENB gets active
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 25 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
MCLK
HSYNC
B
G
B
G
DATA
Time
Slot
Line Head
Blank
12 clocks
⋅⋅⋅⋅⋅⋅⋅⋅⋅
B⋅
G
B
G
Line Tail
Blank
12 clocks
IMAGE RAW DATA
Window Width
804 clocks
HBLANK
3 clocks
Clock
SensorArrayWidth (828)
Ruler
HBLANK(3)
Fig.6 Even Line Data Timing
MCLK
HSYNC
G
DATA
Time
Slot
Line Head
Blank
12 clocks
R
G
R
⋅⋅⋅⋅⋅⋅⋅⋅⋅
G⋅
R
IMAGE RAW DATA
Window Width
804 clocks
G
R
Line Tail
Blank
12 clocks
HBLANK
3 clocks
Clock
Ruler
SensorArrayWidth (828)
HBLANK(3)
Fig.7 Odd Line Data Timing
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 26 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
CMOS IMAGE SENSOR
With 8-bit ADC
PRELIMINARY
MCLK
HSYNC
VSYNC
....
DATA
Time
Slot
≈
G
R
IMAGE RAW DATA
Window Width
804 clocks
B
Line Tail
Blank
12 clocks
HBLANK
3 clocks
Idle Slot
(Integration Time EffectiveWindowHei
ght) * 1024
= (600 - 482) * 1024
VSYNC
3 clocks
Line Head
Blank
12 clocks
G
.....
IMAGE RAW DATA
Window Width
804 clocks
≈
Integration Time > EffectiveWindowHeight * Scale
Fig.8 Frame Transition Timing
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 27 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
PACKAGE DIMENSION (48 PIN CLCC)
CMOS IMAGE SENSOR
With 8-bit ADC
UNIT: mm
C
0.53
0.98
* C : Center of Image Area
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 28 -
1999 Hyundai System IC Division
HB7121B
Electronics Industries Co., Ltd.
System IC Division
PRELIMINARY
CMOS IMAGE SENSOR
With 8-bit ADC
MEMO
Hyundai Electronics Industries Co., Ltd
System IC Division
Headquarter & Factory
San 136-1,Ami-Ri,Bubal-Eub,Ichon-Si,Kyoungki-Do,Korea 467-860
Tel : 82-336-630-2042/2484, Fax : 82-336-639-1412, E-mail : [email protected]
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume
any responsibility for use of circuits described. NO patent licenses are implied.
DA21991011R_1.0
- 29 -
1999 Hyundai System IC Division