HIGHPERFORMANCE CPUs SINGLE-BOARD COMPUTERS VMP1 VME Processor Module Computing in rugged environment Integrated PowerPC MPC8240 with internal MPC603e core VME64 industry standard interface PCI local bus 33 MHz PCI Expansion Connector Up to 128 MB SDRAM/100 MHz Up to 8MB Flash Optional Flash disk or NVSRAM Fast Ethernet Two RS232 ports Rugged 3U design Extended temperature version Universal Boot Loader A well-balanced design achieving a maximum of computer performance versus power dissipation, realized using the highly integrated MPC8240 PowerPC, embedded in a rugged design. RTIFIED CE Q UA M DIN ISO 9001 LIT Y SYS Reg. No. 0548 - 02 TE PUSH BUTTONS/ LED’S SYSTEM LOGIC Memory Bus (64bit) Port X (8 bit wide) PEP’s VME PowerPC Processor board with Floating point unit based on the MPC8240 is a straight forward computing design. POWER SUPPLY SERIAL INTERFACE 1 HIGHPERFORMANCE CPUs SINGLE-BOARD COMPUTERS FLASH SOCKET DiskOnChip or NVSRAM FLASH CPU Power PC MPC8240 SDRAM 100MHz ECC P1 Connector Product Overview VMP1 DEBUG PCI EXPANSION CONNECTOR SERIAL INTERFACE 2 RTC RESET GENERATION EEPROM CPU, Memory and DMA VME interface The VMEbus interface (Universe 2) delivers beside all functionality that is needed by a VME CPU: – automatic First-Slot-Detection – integral FIFO buffers for multiple transactions in both directions – programmable DMA controller with linked list support. for use with maintenance and diagnostic utilities. Further a watch point and capture register on the internal bus as well as a set of address attributes on the external memory and PCI buses aid in debugging analysis. LAN The i82559 10/100 Mbps Fast Ethernet controller with an integrated 10/100 Mbps physical layer device is the foremost solution for PCI board LAN designs. It combines a low power consumption with a small package design which is ideal for power and space constrained environments. Serial ports Two RS232 serial ports are realized with the 16C2550 UART and supports baud rates up to 1.5Mbps. Universal Boot Loader The VMP1 employs an operating system independent boot loader that enables the loading of any OS.This boot loader makes an update of the Flash contents and accomplishes an automatic download from Flash to SDRAM before booting the OS. For high performance reasons the OS is started from the SDRAM. Front-Panel VMP1 Support One of the prime advantages of utilizing the existing, time-tested, and proven MPC603e core is the legacy and infrastructure of support that currently exists. All notable thirdparty software tool vendors presently endorsing the PowerPC architecture have announced tools also for the MPC8240. It supports processor control and visibility through the JTAG/COP (common on-chip processor) interface that is accessible on VMP1. Utilizing third party tools, the developer can access and control the processor. It also has standard IEEE 1149.1a-1993 compliant boundary scan capability.The ECC data path has a mechanism to manually inject errors into memory U RST W H AB SER 0 PCI is used as the local bus to connect the MPC8240 with the Fast Ethernet controller and the PCI/VME bridge. Moreover, it is routed to a 100 pin PCI expansion connector that can be used to add further functionality to the VMP1. One or two VMP1-IO modules can be plugged together with the VMP1 (e.g. two PMC slots can be added) resulting in a total package of either 8HP or 12HP. VME INTERFACE PCI Bus TERM PCI bus and PCI Expansion capability FAST ETHERNET LNK. ACT. SPEED Fast Ethernet The VMP1 is a comprehensive computing platform realized as a lean CPU design with only those functions required for basic industrial calculation tasks. It addresses the need for increasing computing capacity while reducing the number of system components and taking up less space. Based on the MPC8240, a highly integrated microprocessor containing a PowerPC MPC603e core, two different clock versions, 200 MHz and 266 MHz, both with an FPU unit will be initially available. Anticipating the VMP1's use in data critical applications, the memory data path contains a selectable in-line ECC controller which can provide SDRAM single bit error correct or double bit error detect. For mass data transmission a dual channel DMA controller is provided. It can be programmed directly or through the use of descriptor chains located in memory. Data can thus be moved from PCI to memory or vice versa, memory to memory, or PCI to PCI. VMP 1 VMP IO11 Specifications VMP1 Processor Integrated PowerPC microprocessor Motorola MPC8240 L1 cache 2 x 16 kB data/instruction cache; Internal processor core MPC603e Core Frequency 200 MHz or 250 MHz 6.6 SPECint95 5.5 SPECfp95 375 Dhrystone (2.1) MIPS PCI bridge and PCI arbiter Two channel controller DMA with chaining Programmable IRQ controller Multiple timers and counters PCI Expansion Interface 32 bit/33 MHz; 5 V Signaling; Up to two expansion modules are stackable. 8 HP/12 HP version with one/two PMC slots or two/four PC*MIP slots.This port can also be used to add customized functionality. VME Interface ANSI/VITA 1-1994 VME64 interface on P1 (IEEE STD 1014); Universe 2 DTB Master/Slave A16-A24; D08-D16 9 user programmable slave images on VME and PCI bus 4 mailboxes and location monitors for message oriented systems 7 IRQ lines with flexible mapping Memory Up to 128 MB direct soldered SDRAM/64 bit/100 MHz with ECC protection (8 bit parity) Up to 8MB direct soldered Flash (Boot Device and Program Storage) DIL Socket for: NV-SRAM (up to 512 kB)/Cell Storage Life 10 years Flash DiskOnChip (up to 144 MB) Miscellaneous Functions Timers: RTC: Debug Port: Four 32-bit timers, one 16-bit timer, one watchdog timer backup via GoldCap (5 days) or optional via replaceable battery (10 years) JTAG/BDM; 16 Pin row connector Front I/O Fast Ethernet Channel 10 Base-T/100 Base-TX; RJ-45; LAN Status LED’s (Activity, Link, Speed) integrated IEEE 802.3 10 BASE-T and 100 BASE-TX compatible PHY integrated power management functions dynamic transmit chaining with multiple priorities transmit queues full duplex support at both 10 and 100 Mbps operation IEEE 802.3u Auto-Negotiation support 3 Kbyte Transmit FIFO and 3 Kbyte Receive FIFO back-to-back transmission support with minimum inter frame spacing IEEE 802.3 x 100 BASE-TX Flow Control support TCP/UDP checksum off-load capabilities Two RS232 ports, 16550 compatible Dual UART; RJ-45 Two push buttons RESET,ABORT (NMI) Board Status LED’s (watchdog active, general purpose) Software Support A Universal Boot Loader supports the start of any operating system like WindRiver’s VxWorks®. Common Temp. Ranges: 0 °C to + 70 °C (standard) –40 °C to + 85 °C extended) –55 °C to + 125 °C (storage) Oper. Humidity: 0% to 95% (noncond.) MTBF according to MIL-HDBK 217F VMP1 164,300h VMP1-IO1 251,000h Power Consumption: + 5V 6,8W*/typ. + 12V 0W* –12V 0W* *Without PCI Expansion Module and at 266 MHz, 64 MB SDRAM, 8MB Flash Dimensions: 100 mm x 160 mm (3U card size) Front Panel Height:: 128.5 mm ; Width: 20 mm (0.8 inch)/4 HP Weight:: 180 g Product Description VMP1 VMP11) VMP1-IO12) FLD-163) FLD-243) FLD-323) 1) NVSRAM5124) Cable-RS232 VxW-BSPVMP15) KIT-VMP1 MAN-VMP1 Order No. 266 MHz MPC8240, 64 MB SDRAM with ECC, 8 MB Flash 200 MHz MPC8240, 32 MB SDRAM without ECC, 4 MB Flash PCI expansion I/O; one PMC slot 16 MByte FLASH-Disk 24 MByte FLASH-Disk 32 MByte FLASH-Disk 20522 20616 20523 19643 19194 19644 512 kByte non volatile SRAM; 32 pin DIP 20656 3 meter RS232 Serial Interface cable with RJ45 to 25 Pin D-Sub (male) for terminal connection VxWorks Board Support Package for development for use with Tornado on 3.5" floppy disk and the boot image integrated into onboard Flash 15191 20657 User’s manual documentation in PDF format on 3.5" floppy disk Printed user’s manual for the VMP1 20615 19973 Note: SDRAM capacity of 96 MB or 128 MB and Flash capacity higher than 8 MB on request PC*MIP or custom I/O modules on request 3) FLASH-Disks up to 144 MByte are also available on request 4) Smaller NVSRAM capacity on request 5) Further Operating System support on request 1) 2) USA GERMANY FRANCE UK SWEDEN BENELUX POLAND ITALY SPAIN NORWAY DENMARK FINLAND SWITZERLAND CZECHIEN HUNGARY CIS CHINA JAPAN KOREA Benelux PEP Modular Computers Benelux Koning-Albert-Laan 46 B-1780 WEMMEL Tel.: ++32 (0)2 456 06 40 Fax: ++32 (0)2 461 00 31 Postbus 9712 NL-4801 LV BREDA Tel.: ++31 (0)76 5217 957 Fax: ++31 (0)76 5217 959 France EURO PEP Paris Les Bureaux du Manoir 18 Chemin du Fond du Chêne F-78 620 L’ETANG LA VILLE Tel.: ++33 (0) 1 39 16 10 30 Fax: ++33 (0) 1 39 16 10 25 Great Britain PEP Modular Computers (UK) Ltd. Riverside Business Centre SHOREHAM-BY-SEA BN43 6RE Tel.: ++44 (0) 1273 44 11 88 Fax: ++44 (0) 1273 44 11 99 Poland PEP Modular Computers Sp. zo.o Al. Jerozolimskie 144 Pok 714 Vp 02-305 WARSZAWA Tel.: ++48 (0) 2 28 23 55 73 Fax: ++48 (0) 2 28 23 55 73 Korea PEP DASAN Systems Co., Ltd. 6F KOSMO Tower 1002 Daechi-dong, Kangnam-ku Seoul, Korea (Zip135-280) Tel.: ++82 2 34 84 - 65 50 Fax: ++82 2 34 84 - 65 51 Sweden PEP Modular Computers AB Hornackersvägen 8 S-18314 TÄBY Tel.: ++46 (0) 8 446 34 60 Fax: ++46 (0) 8 732 63 10 USA PEP Modular Computers Inc. 750 Holiday Drive, Building 9 Pittsburgh, PA 15220 Tel.: ++1 412 921 3322 Fax: ++1 412 921 3356 Toll free: 800/228-1737 Visit our home page at: http://www.pep.com PEP Modular Computers GmbH Sudetenstr. 7 D-87600 KAUFBEUREN Tel.: ++49 (0) 8341 803 0 Fax: ++49 (0) 8341 803 499 © PEP 1999: ™ All trademarks are recognised, Subject to change without notice Publication Number 20693 DS-0799 Ordering Information VMP1