TI TAS5352ADDVR

TM
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
125 W STEREO DIGITAL AMPLIFIER POWER STAGE
FEATURES
1
DESCRIPTION
The TAS5352A is a high-performance, integrated
stereo digital amplifier power stage designed to drive
a 4-Ω bridge-tied load (BTL) at up to 125 W per
channel with low harmonic distortion, low integrated
noise, and low idle current.
The TAS5352A has a complete protection system
integrated on-chip, safeguarding the device against a
wide range of fault conditions that could damage the
system. These protection features are short-circuit
protection, over-current protection, under voltage
protection, over temperature protection, and a loss of
PWM signal (PWM activity detector).
A power-on-reset (POR) circuit is used to eliminate
power-supply sequencing that is required for most
power-stage designs.
BTL OUTPUT POWER
vs
SUPPLY VOLTAGE
150
TC = 75°C
THD+N at 10%
140
130
120
110
PO – Output Power – W
• Total Power Output (Bridge Tied Load)
– 2 × 125 W at 10% THD+N Into 4 Ω
– 2 × 100 W at 10% THD+N Into 6 Ω
• Total Power Output (Single Ended)
– 4 × 45 W at 10% THD+N Into 3 Ω
– 4 × 35 W at 10% THD+N Into 4 Ω
• Total Power Output (Parallel Mode)
– 1 × 250 W at 10% THD+N Into 2 Ω
– 1 × 195 W at 10% THD+N Into 3 Ω
• >110 dB SNR (A-Weighted With TAS5518
Modulator)
• <0.1% THD+N (1 W, 1 kHz)
• Supports PWM Frame Rates of 192 kHz to
432 kHz
• Resistor-Programmable Current Limit
• Integrated Self-Protection Circuitry, Including:
– Under Voltage Protection
– Overtemperature Warning and Error
– Overload Protection
– Short-Circuit Protection
– PWM Activity Detector
• Standalone Protection Recovery
• Power-On Reset (POR) to Eliminate System
Power-Supply Sequencing
• High-Efficiency Power Stage (>90%) With
80-mΩ Output MOSFETs
• Thermally Enhanced 44-Pin HTSSOP Package
(DDV)
• Error Reporting, 3.3-V and 5.0-V Compliant
• EMI Compliant When Used With
Recommended System Design
23
4Ω
100
90
80
6Ω
70
60
50
40
30
8Ω
20
10
0
0
APPLICATIONS
•
•
•
Mini/Micro Audio System
DVD Receiver
Home Theater
2
4
6
8 10 12 14 16 18 20 22 24 26 28 30 32 34
PVDD – Supply Voltage – V
PurePath Digital™
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PurePath Digital, PowerPad are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
GENERAL INFORMATION
Terminal Assignment
The TAS5352A is available in a thermally enhanced 44-pin HTSSOP PowerPad™ package (DDV)
This package contains a thermal pad that is located on the top side of the device for convenient thermal coupling
to the heatsink.
DDV PACKAGE
(TOP VIEW)
GVDD_B
OTW
NC
NC
SD
PWM_A
RESET_AB
PWM_B
OC_ADJ
GND
AGND
VREG
M3
M2
M1
PWM_C
RESET_CD
PWM_D
NC
NC
VDD
GVDD_C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
GVDD_A
BST_A
NC
PVDD_A
PVDD_A
OUT_A
GND_A
GND_B
OUT_B
PVDD_B
BST_B
BST_C
PVDD_C
OUT_C
GND_C
GND_D
OUT_D
PVDD_D
PVDD_D
NC
BST_D
GVDD_D
P0016-02
2
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
Protection MODE Selection Pins
Protection modes are selected by shorting M1, M2, and M3 to VREG or GND.
MODE PINS
(1)
(2)
(3)
Mode Name
PWM Input (1)
0
BTL mode 1
2N
All protection systems enabled
1
BTL mode 2
2N
Latching shutdown on, PWM activity detector and OLP disabled
0
BTL mode 3
1N
M3
M2
M1
0
0
0
0
0
1
1N / 2N
Description
All protection systems enabled
(2)
0
1
1
PBTL mode
1
0
0
SE mode 1
1N
All protection systems enabled
All protection systems enabled (3)
1
0
1
SE mode 2
1N
Latching shutdown on, PWM activity detector and OLP disabled (3)
1
1
0
1
1
1
Reserved
The 1N and 2N naming convention is used to indicate the number of PWM lines to the power stage per channel in a specific mode.
PWM_D is used to select between the 1N and 2N interface in PBTL mode (Low = 1N; High = 2N). PWM_D is internally pulled low in
PBTL mode. PWM_A is used as the PWM input in 1N mode and PWM_A and PWM_B are used as inputs for the 2N mode.
PPSC detection system disabled.
Package Heat Dissipation Ratings (1)
PARAMETER
TAS5352ADDV
RθJC (°C/W)—2 BTL or 4 SE channels
1.3
RθJC (°C/W)—1 BTL or 2 SE channel(s)
2.6
RθJC (°C/W)—1 SE channel
5.0
Power Pad area
(1)
(2)
(2)
36 mm2
JC is junction-to-case, CH is case-to-heatsink.
RθCH is an important consideration. Assume a 2-mil thickness of high performance grease with a thermal conductivity at 2.5W/m-K
between the pad area and the heat sink. The RθCH with this condition is 0.6°C/W for the DDV package.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
3
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted
(1)
TAS5352A
VDD to AGND
–0.3 V to 13.2 V
GVDD_X to AGND
–0.3 V to 13.2 V
(2)
PVDD_X to GND_X
–0.3 V to 53 V
OUT_X to GND_X
(2)
–0.3 V to 53 V
BST_X to GND_X
(2)
–0.3 V to 66.2 V
BST_X to GVDD_X
(2)
–0.3 V to 53 V
VREG to AGND
–0.3 V to 4.2 V
GND_X to GND
–0.3 V to 0.3 V
GND_X to AGND
–0.3 V to 0.3 V
GND to AGND
–0.3 V to 0.3 V
PWM_X, OC_ADJ, M1, M2, M3 to AGND
–0.3 V to 4.2 V
RESET_X, SD, OTW to AGND
–0.3 V to 7 V
Maximum continuous sink current (SD, OTW)
9 mA
Maximum operating junction temperature range, TJ
0°C to 125°C
Storage temperature
–40°C to 125°C
Lead temperature, 1,6 mm (1/16 inch) from case for 10 seconds
260°C
Minimum pulse duration, low
30 ns
(1)
(2)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
These voltages represent the dc voltage + peak ac waveform measured at the terminal of the device in all conditions.
ORDERING INFORMATION (1)
(1)
4
TA
PACKAGE
DESCRIPTION
0°C to 70°C
TAS5352ADDV
44-pin HTSSOP
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
Terminal Functions
TERMINAL
NAME
DDV NO.
FUNCTION
(1)
DESCRIPTION
AGND
11
P
Analog ground
BST_A
43
P
Bootstrap pin, A-Side
BST_B
34
P
Bootstrap pin, B-Side
BST_C
33
P
Bootstrap pin, C-Side
BST_D
24
P
Bootstrap pin, D-Side
GND
10
P
Ground
GND_A
38
P
Power ground for half-bridge A
GND_B
37
P
Power ground for half-bridge B
GND_C
30
P
Power ground for half-bridge C
GND_D
29
P
Power ground for half-bridge D
GVDD_A
44
P
Gate-drive voltage supply; A-Side
GVDD_B
1
P
Gate-drive voltage supply; B-Side
GVDD_C
22
P
Gate-drive voltage supply; C-Side
GVDD_D
23
P
Gate-drive voltage supply; D-Side
M1
15
I
Mode selection pin (LSB)
M2
14
I
Mode selection pin
M3
13
I
Mode selection pin (MSB)
NC
3, 4, 19, 20, 25, 42
–
No connect. Pins may be grounded.
OC_ADJ
9
O
Analog overcurrent programming pin
OTW
2
O
Overtemperature warning signal, open-drain, active-low
OUT_A
39
O
Output, half-bridge A
OUT_B
36
O
Output, half-bridge B
OUT_C
31
O
Output, half-bridge C
OUT_D
28
O
Output, half-bridge D
PVDD_A
40, 41
P
Power supply input for half-bridge A
PVDD_B
35
P
Power supply input for half-bridge B
PVDD_C
32
P
Power supply input for half-bridge C
PVDD_D
26, 27
P
Power supply input for half-bridge D
PWM_A
6
I
PWM Input signal for half-bridge A
PWM_B
8
I
PWM Input signal for half-bridge B
PWM_C
16
I
PWM Input signal for half-bridge C
PWM_D
18
I
PWM Input signal for half-bridge D
RESET_AB
7
I
Reset signal for half-bridge A and half-bridge B, active-low
RESET_CD
17
I
Reset signal for half-bridge C and half-bridge D, active-low
SD
5
O
Shutdown signal, open-drain, active-low
VDD
21
P
Input power supply
VREG
12
P
Internal voltage regulator
(1)
I = input, O = output, P = power
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
5
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
TYPICAL SYSTEM BLOCK DIAGRAM
OTW
System
Microcontroller
SD
SD
TAS5518
OTW
I2C
BST_A
BST_B
RESET_AB
RESET_CD
VALID
PWM_A
LeftChannel
Output
OUT_A
Output
H-Bridge 1
Input
H-Bridge 1
PWM_B
OUT_B
Bootstrap
Capacitors
2nd-Order L-C
Output Filter
for Each
Half-Bridge
2-Channel
H-Bridge
BTL Mode
OUT_C
PWM_C
4
34.5 V
PVDD
System
Power
Supply
GND
12 V
4
PVDD
Power
Supply
Decoupling
OC_ADJ
AGND
VREG
GND
M3
2nd-Order L-C
Output Filter
for Each
Half-Bridge
BST_C
VDD
M2
OUT_D
GVDD_A, B, C, D
M1
GND_A, B, C, D
PWM_D
Hardwire
Mode
Control
Output
H-Bridge 2
Input
H-Bridge 2
PVDD_A, B, C, D
RightChannel
Output
BST_D
Bootstrap
Capacitors
4
GVDD
VDD
VREG
Power Supply
Decoupling
Hardwire
OC Limit
GND
GVDD (12 V)/VDD (12 V)
VAC
B0047-02
6
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
FUNCTIONAL BLOCK DIAGRAM
VDD
4
Undervoltage
Protection
OTW
Internal Pullup
Resistors to VREG
SD
M1
Protection
and
I/O Logic
M2
M3
4
VREG
VREG
Power
On
Reset
AGND
Temp.
Sense
GND
RESET_AB
Overload
Protection
RESET_CD
OC_ADJ
Isense
GVDD_D
BST_D
PVDD_D
PWM_D
PWM
Rcv.
Ctrl.
Timing
Gate
Drive
OUT_D
BTL/PBTL−Configuration
Pulldown Resistor
GND_D
GVDD_C
BST_C
PVDD_C
PWM_C
PWM
Rcv.
Ctrl.
Timing
Gate
Drive
OUT_C
BTL/PBTL−Configuration
Pulldown Resistor
GND_C
GVDD_B
BST_B
PVDD_B
PWM_B
PWM
Rcv.
Ctrl.
Timing
Gate
Drive
OUT_B
BTL/PBTL−Configuration
Pulldown Resistor
GND_B
GVDD_A
BST_A
PVDD_A
PWM_A
PWM
Rcv.
Ctrl.
Timing
Gate
Drive
OUT_A
BTL/PBTL−Configuration
Pulldown Resistor
GND_A
B0034-03
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
7
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
RECOMMENDED OPERATING CONDITIONS
MIN
TYP
MAX
UNIT
PVDD_X
Half-bridge supply voltage
0
34.5
37
V
GVDD_X
Supply voltage for logic regulators and
gate-drive circuitry
10.8
12
13.2
V
VDD
Digital regulator supply voltage
10.8
12
13.2
V
3
4
2.25
3
RL (BTL)
RL (SE)
RL (PBTL)
Resistive load impedance (no Cycle-by_Cycle
current control), recommended demodulation
filter
1.5
2
5
10
5
10
5
10
LOutput (BTL)
LOutput (SE)
Minimum output inductance under
short-circuit condition
Output-filter inductance
LOutput (PBTL)
µH
fS
PWM frame rate
192
tLOW
Minimum low-state pulse duration per PWM
Frame, noise shaper enabled
30
CPVDD
PVDD close decoupling capacitors
0.1
µF
CBST
Bootstrap capacitor, selected value supports
PWM frame rates from 192 kHz to 432 kHz
33
nF
ROC
Over-current programming resistor
REXT-PULLUP
External pull-up resistor to +3.3V to +5.0V for
SD or OTW
TJ
Junction temperature
Resistor tolerance = 5%
384
Ω
432
kHz
nS
22
22
3.3
4.7
0
47
kΩ
kΩ
125
°C
AUDIO SPECIFICATIONS (BTL)
Audio performance is recorded as a chipset consisting of a TAS5518 pwm processor (modulation index limited to 97.7%) and
a TAS5352A power stage. PCB and system configuration are in accordance with recommended guidelines. Audio frequency
= 1kHz, PVDD_x = 34.5 V, GVDD_x = 12 V, RL = 4Ω, fS = 384 kHz, ROC = 22 kΩ, TC = 75°C, Output Filter: LDEM = 10 µH,
CDEM = 470 nF, unless otherwise noted.
PARAMETER
POMAX
Maximum Power Output
PO
TAS5352A
TEST CONDITIONS
Unclipped Power Output
MIN
TYP
RL = 4 Ω, 10% THD+N, clipped input
signal
125
RL = 6 Ω, 10% THD+N, clipped input
signal
100
RL = 8 Ω, 10% THD+N, clipped input
signal
76
RL = 4 Ω, 0 dBFS, unclipped input
signal
96
RL = 6 Ω, 0 dBFS, unclipped input
signal
72
RL = 8 Ω, 0 dBFS, unclipped input
signal
57
0 dBFS; AES17 filter
MAX
UNIT
W
0.4%
THD+N
Total harmonic distortion + noise
Vn
Output integrated noise
A-weighted, AES17 filter, Auto mute
disabled
50
µV
SNR
Signal-to-noise ratio
(1)
A-weighted, AES17 filter, Auto mute
disabled
110
dB
DNR
Dynamic range
A-weighted, input level = –60 dBFS,
AES17 filter
110
dB
DC Offset
Output offset voltage
+/- 15
mV
Pidle
Power dissipation due to idle losses (IPVDD_X)
2.6
W
(1)
(2)
8
1 W; AES17 filter
0.09%
PO = 0 W, all halfbridges switching (2)
SNR is calculated relative to 0-dBFS input level.
Actual system idle losses are affected by core losses of output inductors.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
AUDIO SPECIFICATIONS (Single-Ended Output)
Audio performance is recorded as a chipset consisting of a TAS5086 pwm processor (modulation index limited to 97.7%) and
a TAS5352A power stage. PCB and system configuration are in accordance with recommended guidelines. Audio frequency
= 1kHz, PVDD_x = 34.5 V, GVDD_x = 12 V, RL = 4Ω, fS = 384 kHz, ROC = 22 kΩ, TC = 75°C, Output Filter: LDEM = 20 µH,
CDEM = 1.0 µF, unless otherwise noted.
PARAMETER
POMAX
PO
Maximum Power Output
Unclipped Power Output
THD+N
TAS5352A
TEST CONDITIONS
Total harmonic distortion + noise
MIN
TYP
RL = 3 Ω, 10% THD+N, clipped input
signal
45
RL = 4 Ω, 10% THD+N, clipped input
signal
35
RL = 3 Ω, 0 dBFS, unclipped input
signal
35
RL = 4 Ω, 0 dBFS, unclipped input
signal
25
MAX
UNIT
W
0 dBFS; AES17 filter
0.4%
1 W; AES17 filter
0.09%
Vn
Output integrated noise
A-weighted, AES17 filter, Auto mute
disabled
40
µV
SNR
Signal-to-noise ratio (1)
A-weighted, AES17 filter, Auto mute
disabled
109
dB
DNR
Dynamic range
A-weighted, input level = –60 dBFS
AES17 filter
109
dB
2.6
W
Pidle
(1)
(2)
Power dissipation due to idle losses (IPVDD_X) PO = 0 W, all halfbridges switching
(2)
SNR is calculated relative to 0-dBFS input level.
Actual system idle losses are affected by core losses of output inductors.
AUDIO SPECIFICATIONS (PBTL)
Audio performance is recorded as a chipset consisting of a TAS5518 pwm processor (modulation index limited to 97.7%) and
a TAS5352A power stage. PCB and system configuration are in accordance with recommended guidelines. Audio frequency
= 1kHz, PVDD_x = 34.5 V, GVDD_x = 12 V, RL = 3Ω, fS = 384 kHz, ROC = 22 kΩ, TC = 75°C, Output Filter: LDEM = 10 µH,
CDEM = 1 µF, unless otherwise noted.
PARAMETER
POMAX
PO
Maximum Power Output
Unclipped Power Output
THD+N
TAS5352A
TEST CONDITIONS
Total harmonic distortion + noise
MIN
TYP
RL = 3 Ω, 10% THD+N, clipped input
signal
195
RL = 2 Ω, 10% THD+N, clipped input
signal
250
RL = 3 Ω, 0 dBFS, unclipped input
signal
145
RL = 2 Ω, 0 dBFS, unclipped input
signal
190
0 dBFS; AES17 filter
MAX
UNIT
W
0.4%
1 W; AES17 filter
0.09%
Vn
Output integrated noise
A-weighted, AES17 filter, Auto mute
disabled
50
µV
SNR
Signal-to-noise ratio (1)
A-weighted, AES17 filter, Auto mute
disabled
110
dB
DNR
Dynamic range
A-weighted, input level = –60 dBFS
AES17 filter
110
dB
+/- 15
mV
2.6
W
DC Offset
Pidle
(1)
(2)
Output offset voltage
Power dissipation due to idle losses (IPVDD_X) PO = 0 W, all halfbridges switching (2)
SNR is calculated relative to 0-dBFS input level.
Actual system idle losses are affected by core losses of output inductors.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
9
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS
PVDD_x = 34.5 V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 25°C, fS = 384 kHz, unless otherwise specified.
PARAMETER
TAS5352A
TEST CONDITIONS
MIN
TYP
MAX
3
3.3
3.6
Operating, 50% duty cycle
7.2
17
Idle, reset mode
5.5
11
UNIT
Internal Voltage Regulator and Current Consumption
VREG
Voltage regulator, only used as a
reference node
IVDD
VDD supply current
IGVDD_X
Gate supply current per half-bridge
IPVDD_X
Half-bridge idle current
VDD = 12 V
V
mA
50% duty cycle
8
16
Reset mode
1
1.8
50% duty cycle, with 10 µH and 470 nF output
filter.
19.0
25
mA
Reset mode, no switching
525
630
µA
mA
Output Stage MOSFETs
RDSon,LS
Drain-to-source resistance, Low
Side
TJ = 25°C, excludes metalization resistance,
80
89
mΩ
RDSon,HS
Drain-to-source resistance, High
Side
TJ = 25°C, excludes metalization resistance,
80
89
mΩ
I/O Protection
Undervoltage protection limit,
GVDD_X
Vuvp,G
9.5
V
Vuvp,hyst (1)
Undervoltage protection limit,
GVDD_X
250
mV
BSTuvpF
Puts device into RESET when BST
voltage falls below limit
5.9
V
BSTuvpR
Brings device out of RESET when
BST voltage rises above limit
7
V
OTW (1)
Overtemperature warning
OTWHYST (1)
Temperature drop needed below
OTW temp. for OTW to be inactive
after the OTW event
OTE (1)
Overtemperature error threshold
OTEOTWdifferential (1)
OTE - OTW differential, temperature
delta between OTW and OTE
OLPC
Overload protection counter
IOC
Overcurrent limit protection
IOCT
Overcurrent response time
tACTIVITY
Time for PWM activity detector to
activate when no PWM is present
Lack of transition of any PWM input
Output pulldown current of each
half-bridge
Connected when RESET is active to provide
bootstrap capacitor charge. Not used in SE
mode.
DETECTOR
IPD
115
125
135
25
145
155
°C
°C
165
°C
30
°C
fS = 384 kHz
1.25
ms
Resistor—programmable, high-end,
ROC = 22 kΩ with 1 mS pulse
10.9
A
150
ns
13.2
µS
3
mA
Static Digital Specifications
VIH
High-level input voltage
VIL
Low-level input voltage
ILeakage
Input leakage current
PWM_A, PWM_B, PWM_C, PWM_D, M1,
M2, M3, RESET_AB, RESET_CD
2
V
0.8
V
100
µA
kΩ
OTW/SHUTDOWN (SD)
RINT_PU
Internal pullup resistance, OTW to
VREG, SD to VREG
VOH
High-level output voltage
(1)
10
Internal pullup resistor
External pullup of 4.7 kΩ to 5 V
20
26
32
3
3.3
3.6
4.5
5
V
Specified by design
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
ELECTRICAL CHARACTERISTICS (continued)
PVDD_x = 34.5 V, GVDD_X = 12 V, VDD = 12 V, TC (Case temperature) = 25°C, fS = 384 kHz, unless otherwise specified.
PARAMETER
TAS5352A
TEST CONDITIONS
MIN
TYP
MAX
0.4
VOL
Low-level output voltage
IO = 4 mA
0.2
FANOUT
Device fanout OTW, SD
No external pullup
30
UNIT
V
Devices
TYPICAL CHARACTERISTICS, BTL CONFIGURATION
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
OUTPUT POWER
vs
SUPPLY VOLTAGE
150
10
TC = 75°C
THD+N at 10%
THD+N – Total Hamonic Distortion – %
5
TC = 75°C
THD+N at 10%
140
130
120
2
110
PO – Output Power – W
1
0.5
4W
0.2
6W
0.1
0.05
4Ω
100
90
80
6Ω
70
60
50
40
30
0.02
0.01
8Ω
20
8W
10
0.005
20m
0
50m 100m 200m 500m
1
5
2
10
20
50
100 200
0
2
4
120
115
110
105
100
95
90
85
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
6
8 10 12 14 16 18 20 22 24 26 28 30 32 34
PVDD – Supply Voltage – V
Figure 1.
Figure 2.
UNCLIPPED OUTPUT POWER
vs
SUPPLY VOLTAGE
SYSTEM EFFICIENCY
vs
OUTPUT POWER
100
95
TC = 75°C
90
85
80
8W
6W
8
75
70
8W
4
65
4W
Efficiency – %
PO – Output Power – W
PO – Output Power – W
6W
60
55
50
45
40
35
30
25
20
8W
TC = 25°C
THD+N at 10%
15
10
5
0
0
2
4
6
8 10 12 14 16
18 20 22 24 26 28 30 32 34
0
0
PVDD – Supply Voltage – V
40
80
120
160
200
240
280
2 Channels Output Power – W
Figure 3.
Figure 4.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
11
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)
SYSTEM POWER LOSS
vs
OUTPUT POWER
SYSTEM OUTPUT POWER
vs
CASE TEMPERATURE
160
40
TC = 25°C
THD+N at 10%
38
36
150
140
34
130
32
PO – Output Power – W
28
26
Power Loss – W
4W
6
120
4W
30
24
22
20
18
16
14
4
8W
110
100
90
80
70
60
8W
50
12
8W
6
10
40
8
30
6
20
8W
4
THD+N at 10%
10
2
0
0
20
40
60
80
0
10
100 120 140 160 180 200 220 240 260 280
20
2 Channels Output Power – W
30
40
50
60
70
80
90
100 110 120
TC – Case Temperature – °C
Figure 5.
Figure 6.
NOISE AMPLITUDE
vs
FREQUENCY
+0
–10
–20
–30
TC = 75°C
VREF = 20.60 V
Sample Rate = 48 kHz
FFT Size = 16384
–40
Noise Amplitude – V
–50
–60
–70
–80
–90
–100
–110
–120
–130
–140
–150
–160
0 1k 2k 3k 4k 5k 6k 7k 8k 9k 10k 11k 12k 13k 14k 15k 16k 17k 18k 19k 20k 21k 22k
f – Frequency – kHz
Figure 7.
12
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
TYPICAL CHARACTERISTICS, SE CONFIGURATION
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
OUTPUT POWER
vs
SUPPLY VOLTAGE
60
57.5
55
52.5
50
47.5
45
42.5
40
37.5
35
32.5
30
27.5
25
22.5
20
17.5
15
12.5
10
7.5
5
2.5
5
TC = 75°C
THD+N at 10%
2
PO – Output Power – W
THD+N – Total Hamonic Distortion – %
10
1
0.5
3W
0.2
0.1
0.05
4W
0.02
0.01
0.005
20m
50m 100m 200m 500m
1
5
2
10
20
0
50 80
TC = 75°C
THD+N at 10%
3W
4W
0
2
4
6
8
10 12 14
16 18
20
22 24
26 28 30 32
34
PVDD – Supply Voltage – V
PO – Output Power – W
Figure 8.
Figure 9.
PO – Output Power – W
OUTPUT POWER
vs
CASE TEMPERATURE
60
57.5
55
52.5
50
47.5
45
42.5
40
37.5
35
32.5
30
27.5
25
22.5
20
17.5
15
12.5
10
7.5
5
2.5
3W
4W
THD+N at 10%
0
10
20
30
40
50
60
70
80
90
100
110
120
TC – Case Temperature – °C
Figure 10.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
13
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS, PBTL CONFIGURATION
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
OUTPUT POWER
vs
SUPPLY VOLTAGE
300
5
TC = 75°C
THD+N at 10%
TC = 75°C
THD+N at 10%
280
4W
260
240
2
4W
2
220
PO – Output Power – W
THD+N – Total Hamonic Distortion – %
10
1
0.5
2W
0.2
0.1
0.05
3W
200
180
160
3W
4
140
120
100
4W
80
60
0.02
40
8W
0.01
0.005
20m
8W
20
0
50m 100m 200m 500m 1
2
5
10
20
50
0
100 200 400
2
4
6
8
10 12 14 16 18 20 22 24 26
28 30 32
34
PVDD – Supply Voltage – V
PO – Output Power – W
Figure 11.
Figure 12.
SYSTEM OUTPUT POWER
vs
CASE TEMPERATURE
300
280
260
4W
3
240
8W
2
220
PO – Output Power – W
200
180
160
140
120
8W
4
100
80
60
40
8W
THD+N at 10%
20
0
10
20
30
40
50
60
70
80
90
100
110
120
TC – Case Temperature – °C
Figure 13.
14
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
APPLICATION INFORMATION
PCB Material Recommendation
FR-4 Glass Epoxy material with 2 oz. (70 µm) is recommended for use with the TAS5352A. The use of this
material can provide for higher power output, improved thermal performance, and better EMI margin (due to
lower PCB trace inductance.
PVDD Capacitor Recommendation
The large capacitors used in conjunction with each full-bridge, are referred to as the PVDD Capacitors. These
capacitors should be selected for proper voltage margin and adequate capacitance to support the power
requirements. In practice, with a well designed system power supply, 1000 µF, 50-V will support more
applications. The PVDD capacitors should be low ESR type because they are used in a circuit associated with
high-speed switching.
Decoupling Capacitor Recommendations
In order to design an amplifier that has robust performance, passes regulatory requirements, and exhibits good
audio performance, good quality decoupling capacitors should be used. In practice, X7R should be used in this
application.
The voltage of the decoupling capacitors should be selected in accordance with good design practices.
Temperature, ripple current, and voltage overshoot must be considered. This fact is particularly true in the
selection of the 0.1µF that is placed on the power supply to each half-bridge. It must withstand the voltage
overshoot of the PWM switching, the heat generated by the amplifier during high power output, and the ripple
current created by high power output. A minimum voltage rating of 50-V is required for use with a 34.5 V power
supply.
System Design Recommendations
The following schematics and PCB layouts illustrate "best practices" in the use of the TAS5352A.
GVDD (+12 V)
PVDD
2.2 W
2.2 W
3.3 W
470 µF
50 V
100 nF
100 nF
10 nF
50 V
TAS5352ADDV
GND
GND
GVDD_B
Microcontroller
OTW
I2C
GND
PWM1_P
VALID
PWM1_M
22 k
NC
NC
PVDD_A
SD
PVDD_A
PWM_A
OUT_A
RESET_AB
GND_A
PWM_B
GND_B
OC_ADJ
OUT_B
AGND
VREG
100 nF
PWM2_P
TAS5508/18
0W
BST_C
M2
OUT_C
M1
GND_C
PWM_C
GND_D
PVDD_D
NC
PVDD_D
VDD
100 nF
GVDD_C
GND
10 nF
50 V
470 nF
100 nF
50 V
GND
1 nF
50 V
GND
10 nF
50 V
3.3 W
10 µH
10 µH
33 nF 25V
GND
NC
3.3 W
1 nF
50 V
100 nF
50 V
10 nF
50 V
100 nF
50 V
470 nF
100 nF
50 V
100 nF
50 V
GND
1 nF
50 V
GND
GND
10 nF
50 V
3.3 W
10 µH
BST_D
GVDD_D
33 nF 25 V
PVDD
3.3 W
GND
470 µF
50 V
10 nF
50 V
100 nF
100 nF
2.2 W
VDD (+12 V)
100 nF
50 V
100 nF
50 V
33 nF 25 V
OUT_D
PWM_D
NC
GND
100 nF
50 V
3.3 W
1 nF
50 V
BST_B
PVDD_C
RESET_CD
33 nF 25 V
GND
PVDD_B
M3
PWM2_M
GND
10 µH
BST_A
NC
GND
GND
GVDD_A
GND
2.2 W
GND
GND
GVDD (+12 V)
Figure 14. Typical Differential (2N) BTL Application With AD Modulation Filters
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
15
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
GVDD (+12 V)
PVDD
2.2 W
2.2 W
3.3 W
470 µF
50 V
100 nF
100 nF
10 nF
50 V
TAS5352ADDV
GND
GND
GVDD_B
Microcontroller
OTW
I2C
GND
PWM1_P
VALID
22 k
NC
NC
PVDD_A
SD
PVDD_A
PWM_A
OUT_A
RESET_AB
GND_A
PWM_B
GND_B
OC_ADJ
OUT_B
AGND
VREG
100 nF
PWM2_P
TAS5508/18
0W
OUT_C
M1
GND_C
PWM_C
GND_D
GND
10 nF
50 V
100 nF
50 V
GND
1 nF
50 V
GND
10 nF
50 V
3.3 W
10 µH
10 µH
33 nF 25V
PVDD_D
NC
PVDD_D
GND
NC
3.3 W
1 nF
50 V
100 nF
50 V
10 nF
50 V
100 nF
50 V
470 nF
100 nF
50 V
100 nF
50 V
GND
1 nF
50 V
GND
GND
10 nF
50 V
3.3 W
10 µH
BST_D
GVDD_D
33 nF 25 V
PVDD
3.3 W
GND
470 µF
50 V
10 nF
50 V
100 nF
100 nF
2.2 W
VDD (+12 V)
100 nF
50 V
470 nF
100 nF
50 V
33 nF 25 V
OUT_D
PWM_D
GVDD_C
100 nF
BST_C
PVDD_C
VDD
100 nF
50 V
3.3 W
1 nF
50 V
BST_B
M2
NC
GND
33 nF 25 V
GND
PVDD_B
M3
RESET_CD
GND
10 µH
BST_A
NC
GND
GND
GVDD_A
GND
2.2 W
GND
GND
GVDD (+12 V)
Figure 15. Typical Non-Differential (1N) BTL Application With AD Modulation Filters
16
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
2
2
GVDD (+12V)
2
2
TAS5352ADDV
GND
1
Microcontroller
2
3
I2C
4
GVDD_B
GVDD_A
OTW
BST_A
NC
NC
NC
PVDD_A
SD
PVDD_A
GND
44
20uH
43
1
2
33nF
42
1
GND
2
A
25V
GND
41
1
GND
VALID
7
8
PWM2_P
9
OUT_A
RESET_AB
GND_A
PWM_B
GND_B
OC_ADJ
OUT_B
40
100nF
50V
39
38
GND
37
100nF
50V
36
2
2
PWM_A
2
6
1
5
PWM1_P
22k
10nF
50V
2
2
100nF
2
1
470uF
50V
100nF
1
3.3R
1
1
1
2.2R
1
1
1
PVDD
2.2R
10
GND
1
11
2
12
100nF
PVDD_B
AGND
BST_B
VREG
BST_C
M3
PVDD_C
35
34
33nF
1
33
1
25V
2
1
2
1
20uH
2
B
2
C
20uH
33nF
32
25V
1
13
GND
14
M2
OUT_C
M1
GND_C
PWM_C
GND_D
30
100nF
50V
GND
2
15
31
16
29
1
PWM3_P
18
19
TAS5508/18
20
GND
0R
2
21
1
1
22
100nF
RESET_CD
OUT_D
PWM_D
PVDD_D
NC
PVDD_D
NC
NC
VDD
BST_D
GVDD_C
GVDD_D
28
100nF
50V
27
2
17
PWM4_P
26
25
GND
24
1
20uH
2
33nF
23
1
2
D
25V
1
3.3R
1
2
PVDD
1
2
10nF
50V
2
100nF
2
2.2R
1
2.2R
1
GND
2
1
2
100nF
470uF
50V
2
2
1
GND
GND
GND
VDD (+12V)
GVDD (+12V)
10nF
50V
1
2
1
2
1
1
10nF
50V
GND
GND
2
3.3R
2
3.3R
2
1
2
1 2
GND
1
2
1
2
2
1
1
3.3R
2
2
2
100nF
50V
10k
1%
470uF
50V
3.3R
1
GND
1
1
10k
1%
470uF
50V
1
2
2
1 2
GND
2
1
2
100nF
50V
10k
1%
470uF
50V
100nF
50V
1uF
10k
PVDD
1
2
1
2
1
2
1
10k
1%
470uF
50V
2
1
100nF
50V
1uF
10k
PVDD
1
B
1
A
2
50V
10nF
1
GND
10nF
50V
GND
10nF
50V
1
2
1
2
1
1
2
50V
10nF
GND
GND
GND
2
3.3R
2
3.3R
1
2
2
1
1
1 2
2
1
2
2
50V
10nF
GND
3.3R
2
2
2
3.3R
1
100nF
50V
1
1
10k
1%
470uF
50V
1
GND
10k
1%
470uF
50V
2
1
GND
2
1 2
100nF
50V
2
10k
1%
470uF
50V
100nF
50V
1uF
10k
PVDD
1
2
1
2
1
2
2
1
1
2
1
10k
1%
470uF
50V
2
100nF
50V
1uF
10k
PVDD
1
D
1
C
GND
GND
1
2
50V
10nF
GND
Figure 16. Typical SE Application
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
17
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
GVDD (+12 V)
PVDD
2.2 W
2.2 W
3.3 W
470 µF
50 V
100 nF
100 nF
10 nF
50 V
TAS5352ADDV
GND
GND
GVDD_B
Microcontroller
I2C
GND
PWM1_P
VALID
PWM1_M
22 k
1R
NC
NC
NC
PVDD_A
SD
PVDD_A
PWM_A
OUT_A
RESET_AB
GND_A
PWM_B
GND_B
OC_ADJ
OUT_B
AGND
VREG
100 nF
0W
GND
M2
OUT_C
M1
GND_C
PWM_C
GND_D
GND
100 nF
50 V
PVDD_D
NC
PVDD_D
100 nF
50 V
10 µH
33 nF 25V
GND
1 nF
50 V
100 nF
50 V
10 nF
50 V
GND
10 nF
50 V
3.3 W
100 nF
50 V
GND
10 µH
BST_D
GVDD_C
33 nF 25 V
GVDD_D
PVDD
3.3 W
GND
470 µF
50 V
10 nF
50 V
100 nF
100 nF
2.2 W
2.2 W
GND
GND
VDD (+12 V)
3.3 W
1 nF
50 V
1 µF
NC
NC
100 nF
50 V
10 µH
33 nF 25 V
OUT_D
PWM_D
VDD
100 nF
BST_C
PVDD_C
RESET_CD
TAS5508/18
100 nF
BST_B
M3
GND
10 µH
33 nF 25 V
GND
PVDD_B
GND
GND
GVDD_A
BST_A
OTW
GND
GVDD (+12 V)
Figure 17. Typical Differential (2N) PBTL Application With AD Modulation Filters
GVDD (+12 V)
PVDD
2.2 W
2.2 W
3.3 W
470 µF
50 V
100 nF
100 nF
10 nF
50 V
TAS5352ADDV
GND
GND
GVDD_B
Microcontroller
OTW
I2C
GND
PWM1_P
VALID
PWM1_M
22 k
1R
NC
NC
PVDD_A
SD
PVDD_A
PWM_A
OUT_A
RESET_AB
GND_A
PWM_B
GND_B
OC_ADJ
OUT_B
AGND
VREG
100 nF
TAS5508/18
0W
GND
OUT_C
M1
GND_C
PWM_C
GND_D
PVDD_D
NC
PVDD_D
GVDD_C
GND
100 nF
50 V
3.3 W
1 nF
50 V
10 nF
50 V
1 µF
10 µH
33 nF 25V
GND
NC
100 nF
50 V
1 nF
50 V
100 nF
50 V
GND
10 nF
50 V
3.3 W
100 nF
50 V
GND
10 µH
BST_D
GVDD_D
33 nF 25 V
PVDD
3.3 W
GND
470 µF
50 V
10 nF
50 V
100 nF
100 nF
2.2 W
VDD (+12 V)
100 nF
50 V
10 µH
33 nF 25 V
OUT_D
PWM_D
VDD
100 nF
BST_C
M2
NC
100 nF
50 V
BST_B
PVDD_C
RESET_CD
33 nF 25 V
GND
PVDD_B
M3
GND
10 µH
BST_A
NC
GND
GND
GVDD_A
GND
2.2 W
GND
GND
GVDD (+12 V)
Figure 18. Typical Non-Differential (1N) PBTL Application
18
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
THEORY OF OPERATION
POWER SUPPLIES
To facilitate system design, the TAS5352A needs
only a 12 V supply in addition to the (typical) 34.5 V
power-stage supply. An internal voltage regulator
provides suitable voltage levels for the digital and
low-voltage analog circuitry. Additionally, all circuitry
requiring a floating voltage supply, e.g., the high-side
gate drive, is accommodated by built-in bootstrap
circuitry requiring only an external capacitor for each
half-bridge.
In order to provide outstanding electrical and
acoustical characteristics, the PWM signal path
including gate drive and output stage is designed as
identical, independent half-bridges. For this reason,
each half-bridge has separate gate drive supply
(GVDD_X), bootstrap pins (BST_X), and power-stage
supply pins (PVDD_X). Furthermore, an additional pin
(VDD) is provided as supply for all common circuits.
Although supplied from the same 12-V source, it is
highly recommended to separate GVDD_A,
GVDD_B, GVDD_C, GVDD_D, and VDD on the
printed-circuit board (PCB) by RC filters (see
application diagram for details). These RC filters
provide the recommended high-frequency isolation.
Special attention should be paid to placing all
decoupling capacitors as close to their associated
pins as possible. In general, inductance between the
power supply pins and decoupling capacitors must be
avoided. (See reference board documentation for
additional information.)
For a properly functioning bootstrap circuit, a small
ceramic capacitor must be connected from each
bootstrap pin (BST_X) to the power-stage output pin
(OUT_X). When the power-stage output is low, the
bootstrap capacitor is charged through an internal
diode connected between the gate-drive power-supply pin (GVDD_X) and the bootstrap pin. When
the power-stage output is high, the bootstrap
capacitor potential is shifted above the output
potential and thus provides a suitable voltage supply
for the high-side gate driver. In an application with
PWM switching frequencies in the range from 352
kHz to 384 kHz, it is recommended to use 33-nF
ceramic capacitors, size 0603 or 0805, for the
bootstrap supply. These 33-nF capacitors ensure
sufficient energy storage, even during minimal PWM
duty cycles, to keep the high-side power stage FET
(LDMOS) fully turned on during the remaining part of
the PWM cycle. In an application running at a
reduced switching frequency, generally 192 kHz, the
bootstrap capacitor might need to be increased in
value.
Special attention should be paid to the power-stage
power supply; this includes component selection,
PCB placement, and routing. As indicated, each
half-bridge has independent power-stage supply pins
(PVDD_X). For optimal electrical performance, EMI
compliance, and system reliability, it is important that
each PVDD_X pin is decoupled with a 100-nF
ceramic capacitor placed as close as possible to
each supply pin. It is recommended to follow the PCB
layout of the TAS5352A reference design. For
additional information on recommended power supply
and required components, see the application
diagrams given previously in this data sheet.
The 12 V supply should be from a low-noise,
low-output-impedance voltage regulator. Likewise, the
34.5 V power-stage supply is assumed to have low
output impedance and low noise. The power-supply
sequence is not critical as facilitated by the internal
power-on-reset circuit. Moreover, the TAS5352A is
fully protected against erroneous power-stage turnon
due to parasitic gate charging. Thus, voltage-supply
ramp rates (dV/dt) are non-critical within the specified
range (see the Recommended Operating Conditions
section of this data sheet).
SYSTEM POWER-UP/POWER-DOWN
SEQUENCE
Powering Up
The TAS5352A does not require a power-up
sequence. The outputs of the H-bridges remain in a
high-impedance state until the gate-drive supply
voltage (GVDD_X) and VDD voltage are above the
undervoltage protection (UVP) voltage threshold (see
the Electrical Characteristics section of this data
sheet). Although not specifically required, it is
recommended to hold RESET_AB and RESET_CD in
a low state while powering up the device. This allows
an internal circuit to charge the external bootstrap
capacitors by enabling a weak pulldown of the
half-bridge output.
When the TAS5352A is being used with TI PWM
modulators such as the TAS5518, no special
attention to the state of RESET_AB and RESET_CD
is required, provided that the chipset is configured as
recommended.
Powering Down
The TAS5352A does not require a power-down
sequence. The device remains fully operational as
long as the gate-drive supply (GVDD_X) voltage and
VDD voltage are above the undervoltage protection
(UVP) voltage threshold (see the Electrical
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
19
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
Characteristics section of this data sheet). Although
not specifically required, it is a good practice to hold
RESET_AB and RESET_CD low during power down,
thus preventing audible artifacts including pops or
clicks.
signal using the system microcontroller and
responding to an overtemperature warning signal by,
e.g., turning down the volume to prevent further
heating of the device resulting in device shutdown
(OTE).
When the TAS5352A is being used with TI PWM
modulators such as the TAS5518, no special
attention to the state of RESET_AB and RESET_CD
is required, provided that the chipset is configured as
recommended.
To reduce external component count, an internal
pullup resistor to 3.3 V is provided on both SD and
OTW outputs. Level compliance for 5-V logic can be
obtained by adding external pullup resistors to 5 V
(see the Electrical Characteristics section of this data
sheet for further specifications).
Mid Z Sequence Compatibility
The TAS5352A is compatible with the Mid Z
sequence of the TAS5086 Modulator. The Mid Z
Sequence is a series of pulses that is generated by
the modulator. This sequence causes the power
stage to slowly enable its outputs as it begins to
switch.
By slowly starting the PWM switching, the impulse
response created by the onset of switching is
reduced. This impulse response is the acoustic
artifact that is heard in the output transducers
(loudspeakers) and is commonly termed "click" or
"pop".
The low acoustic artifact noise of the TAS5352A will
be further decreased when used in conjunction with
the TAS5086 modulator with the Mid Z Sequence
enabled.
The Mid Z sequence is primarily used for the
single-ended output configuration. It facilitates a
"softer" PWM output start after the split cap output
configuration is charged.
The TAS5352A contains advanced protection circuitry
carefully designed to facilitate system integration and
ease of use, as well as to safeguard the device from
permanent failure due to a wide range of fault
conditions such as short circuits, overload,
overtemperature, and undervoltage. The TAS5352A
responds to a fault by immediately setting the power
stage in a high-impedance (Hi-Z) state and asserting
the SD pin low. In situations other than overload and
over-temperature
error
(OTE),
the
device
automatically recovers when the fault condition has
been removed, i.e., the supply voltage has increased.
The device will function on errors, as shown in the
following table
BTL MODE
Local
Error
In
A
B
C
ERROR REPORTING
The SD and OTW pins are both active-low,
open-drain
outputs.
Their
function
is
for
protection-mode signaling to a PWM controller or
other system-control device.
Any fault resulting in device shutdown is signaled by
the SD pin going low. Likewise, OTW goes low when
the device junction temperature exceeds 125°C (see
the following table).
SD
OTW
0
0
Overtemperature (OTE) or overload (OLP) or
undervoltage (UVP)
0
1
Overload (OLP) or undervoltage (UVP)
1
0
Junction temperature higher than 125°C
(overtemperature warning)
1
1
Junction temperature lower than 125°C and no
OLP or UVP faults (normal operation)
DESCRIPTION
Note that asserting either RESET_AB or RESET_CD
low forces the SD signal high, independent of faults
being present. TI recommends monitoring the OTW
20
DEVICE PROTECTION SYSTEM
D
Turns Off
A+B
C+D
PBTL MODE
Local
Error
In
Turns Off
A
B
C
D
SE MODE
Local
Error
In
A
A+B+C
+D
B
C
D
Turns Off
A+B
C+D
Bootstrap UVP does not shutdown according to the
table, it shuts down the respective halfbridge.
Use of TAS5352A in High-Modulation-Index
Capable Systems
This device requires at least 30 ns of low time on the
output per 384-kHz PWM frame rate in order to keep
the bootstrap capacitors charged. As an example, if
the modulation index is set to 99.2% in the TAS5508,
this setting allows PWM pulse durations down to 10
ns. This signal, which does not meet the 30-ns
requirement, is sent to the PWM_X pin and this
low-state pulse time does not allow the bootstrap
capacitor to stay charged. The TAS5352A device
requires limiting the TAS5508 modulation index to
97.7% to keep the bootstrap capacitor charged under
all signals and loads.
The TAS5352A contains a bootstrap capacitor under
voltage protection circuit (BST_UVP) that monitors
the voltage on the bootstrap capacitors. When the
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
TAS5352A
www.ti.com ........................................................................................................................................................................................... SLES239 – NOVEMBER 2008
voltage on the bootstrap capacitors is less than
required for proper control of the High-Side
MOSFETs, the device will initiate bootstrap capacitor
recharge sequences until the bootstrap capacitors are
properly charged for robust operation. This function
may be activated with PWM pulses less than 30 nS.
Therefore, TI strongly recommends using a TI PWM
processor, such as TAS5518, TAS5086 or TAS5508,
with the modulation index set at 97.7% to interface
with TAS5352A.
Overcurrent (OC) Protection With Current
Limiting and Overload Detection
The device has independent, fast-reacting current
detectors with programmable trip threshold (OC
threshold) on all high-side and low-side power-stage
FETs. See the following table for OC-adjust resistor
values. The detector outputs are closely monitored by
two protection systems. The first protection system
controls the power stage in order to prevent the
output current from further increasing, i.e., it performs
a current-limiting function rather than prematurely
shutting down during combinations of high-level
music transients and extreme speaker load
impedance drops. If the high-current situation
persists, i.e., the power stage is being overloaded, a
second protection system triggers a latching
shutdown, resulting in the power stage being set in
the high-impedance (Hi-Z) state. Current limiting and
overload protection are independent for half-bridges
A and B and, respectively, C and D. That is, if the
bridge-tied load between half-bridges A and B causes
an overload fault, only half-bridges A and B are shut
down.
• For the lowest-cost bill of materials in terms of
component selection, the OC threshold measure
should be limited, considering the power output
requirement and minimum load impedance.
Higher-impedance loads require a lower OC
threshold.
• The demodulation-filter inductor must retain at
least 5 µH of inductance at twice the OC threshold
setting.
Unfortunately, most inductors have decreasing
inductance with increasing temperature and
increasing current (saturation). To some degree, an
increase in temperature naturally occurs when
operating at high output currents, due to core losses
and the dc resistance of the inductor's copper
winding. A thorough analysis of inductor saturation
and thermal properties is strongly recommended.
Setting the OC threshold too low might cause issues
such as lack of enough output power and/or
unexpected shutdowns due to too-sensitive overload
detection.
In general, it is recommended to follow closely the
external component selection and PCB layout as
given in the Application section.
For added flexibility, the OC threshold is
programmable within a limited range using a single
external resistor connected between the OC_ADJ pin
and AGND. (See the Electrical Characteristics section
of this data sheet for information on the correlation
between programming-resistor value and the OC
threshold.) It should be noted that a properly
functioning overcurrent detector assumes the
presence of a properly designed demodulation filter at
the power-stage output. It is required to follow certain
guidelines when selecting the OC threshold and an
appropriate demodulation inductor:
OC-Adjust Resistor Values
(kΩ)
Max. Current Before OC Occurs
(A), TC = 75°C
22
10.9
33
9.1
47
7.1
The reported max peak current in the table above is
measured with continuous current in 1 Ω, one
channel active and the other one muted.
Pin-To-Pin Short Circuit Protection (PPSC)
The PPSC detection system protects the device from
permanent damage in the case that a power output
pin (OUT_X) is shorted to GND_X or PVDD_X. For
comparison the OC protection system detects an over
current after the demodulation filter where PPSC
detects shorts directly at the pin before the filter.
PPSC detection is performed at startup i.e. when
VDD is supplied, consequently a short to either
GND_X or PVDD_X after system startup will not
activate the PPSC detection system. When PPSC
detection is activated by a short on the output, all half
bridges are kept in a Hi-Z state until the short is
removed, the device then continues the startup
sequence and starts switching. The detection is
controlled globally by a two step sequence. The first
step ensures that there are no shorts from OUT_X to
GND_X, the second step tests that there are no
shorts from OUT_X to PVDD_X. The total duration of
this process is roughly proportional to the capacitance
of the output LC filter. The typical duration is < 15
ms/µF. While the PPSC detection is in progress, SD
is kept low, and the device will not react to changes
applied to the RESET pins. If no shorts are present
the PPSC detection passes, and SD is released. A
device reset will not start a new PPSC detection.
PPSC detection is enabled in BTL and PBTL output
configurations, the detection is not performed in SE
mode. To make sure not to trip the PPSC detection
system it is recommended not to insert resistive load
to GND_X or PVDD_X.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
21
TAS5352A
SLES239 – NOVEMBER 2008 ........................................................................................................................................................................................... www.ti.com
Overtemperature Protection
DEVICE RESET
The
TAS5352A
has
a
two-level
temperature-protection system that asserts an
active-low warning signal (OTW) when the device
junction temperature exceeds 125°C (typical) and, if
the device junction temperature exceeds 155°C
(typical), the device is put into thermal shutdown,
resulting in all half-bridge outputs being set in the
high-impedance (Hi-Z) state and SD being asserted
low. OTE is latched in this case. To clear the OTE
latch, either RESET_AB or RESET_CD must be
asserted. Thereafter, the device resumes normal
operation.
Two reset pins are provided for independent control
of half-bridges A/B and C/D. When RESET_AB is
asserted low, all four power-stage FETs in half-bridges A and B are forced into a high-impedance
(Hi-Z) state. Likewise, asserting RESET_CD low
forces all four power-stage FETs in half-bridges C
and D into a high-impedance state. Thus, both reset
pins are well suited for hard-muting the power stage if
needed.
Undervoltage Protection (UVP) and Power-On
Reset (POR)
The UVP and POR circuits of the TAS5352A fully
protect the device in any power-up/down and
brownout situation. While powering up, the POR
circuit resets the overload circuit (OLP) and ensures
that all circuits are fully operational when the
GVDD_X and VDD supply voltages reach stated in
the Electrical Characteristics Table. Although
GVDD_X and VDD are independently monitored, a
supply voltage drop below the UVP threshold on any
VDD or GVDD_X pin results in all half-bridge outputs
immediately being set in the high-impedance (Hi-Z)
state and SD being asserted low. The device
automatically resumes operation when all supply
voltages have increased above the UVP threshold.
22
In BTL modes, to accommodate bootstrap charging
prior to switching start, asserting the reset inputs low
enables weak pulldown of the half-bridge outputs. In
the SE mode, the weak pulldowns are not enabled,
and it is therefore recommended to ensure bootstrap
capacitor charging by providing a low pulse on the
PWM inputs when reset is asserted high.
Asserting either reset input low removes any fault
information to be signaled on the SD output, i.e., SD
is forced high.
A rising-edge transition on either reset input allows
the device to resume operation after an overload
fault. To ensure thermal reliability, the rising edge of
reset must occur no sooner than 4 ms after the falling
edge of SD.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5352A
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Dec-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TAS5352ADDVR
Package Package Pins
Type Drawing
SPQ
HTSSOP
2000
DDV
44
Reel
Reel
Diameter Width
(mm) W1 (mm)
330.0
24.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
8.6
15.6
1.8
12.0
24.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
22-Dec-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TAS5352ADDVR
HTSSOP
DDV
44
2000
346.0
346.0
41.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated