AIC111 www.ti.com SLAS382 – JUNE 2003 IC DESIGN SPECIFICATION 1.3-V microPower DSP/µC VOICE BAND AUDIO CODEC FEATURES D Single Channel Codec D Noise Shaped Delta Sigma ADC and DAC Technology D Low Supply Voltage and Current: – 1.3-V Typical Power Supply – 350-µA Typical Supply Current Drain D Power Supply Up Monitor and Low Battery Monitor That Also Automatically Shuts Off H-Bridge Output When Battery Decays Below 1.05 V in a Nontransient Manner D Typical 2.4-µVrms Input Referred Noise With 0.01% Total Harmonic Distortion for Front End and 108-dB Dynamic Range D ADC Has 87-dB Dynamic Range With 73-dB Total Harmonic Distortion 100 Hz–10 kHz, 40-kHz Sampling Rate D Typical 55-dB PSRR 100 Hz to 10 kHz for Analog Front End D Low Noise Programmable Gain Amplifier/Compressor Front End With Programmable Fast and Slow Attack and Decay Rates With Dual or Single Attack and Decay Rate Option D Typical Output Noise of 12 µVrms With 0.05% Total Harmonic Distortion for Delta Sigma DAC and H-Bridge Output Driver D Low Jitter Oscillator That Generates all Internal Clocks and Generates 5-MHz Output DSP/µC Clock D Regulated Bandgap Voltage Reference D Programmable Functionality via Digital Serial Interface – McBSP Interface, DSP Protocol – TI TMS320VC54x, TMS320VC55x DSPs – SPI Interface, Microcontroller Protocol – TI MSP430xx D External Chip Power Down and Reset D Available in: – 32-Pin QFN 5×5-mm Plastic Package – 32-Pad Bumped Die in Waffle Pack (wafer scale packaging), or Tape and Reel, (Preview, Available 3rd Quarter 2003) APPLICATIONS D Hearing Instruments D Personal Medical Devices D Hearing Protection D Aural Processing D Low-Power Headsets DESCRIPTION The AIC111 IC design specification serves to provide product development teams with a guideline for how the AIC111 IC is specified and programmable options that are available. The document outlines a top-level block description of the IC along with system specifications and functions. Individual block descriptions and target specifications are also outlined. The Texas Instruments AIC111 is a TI µPower DSP compatible, or microcontroller compatible audio codec product, or analog interface circuit. The AIC111 is part of a comprehensive family of DSP/µC based highperformance analog interface solutions. The AIC111 is targeted primarily at personal medical devices, such as hearing instruments, aural preprocessing applications, and low-power headset applications. The AIC111 is used in any design requiring a programmable time constant PGA/compressor interface, high dynamic range analog-to-digital converter, an external DSP/µC handling signal processing, or a low distortion digital-to-analog converter with a balanced H-Bridge speaker driver. It supports a CMOS digital interface tailored for TI DSPs with the McBSP protocol such as TMS320VC54x DSP family and SPI-based controllers such as TI MSP430x family of microcontrollers. The AIC111 also has an external microphone or sensor supply and bias and power supply up low-battery monitor indicator. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. This document contains information on products in more than one phase of development. The status of each device is indicated on the page(s) specifying its electrical characteristics. Copyright 2003, Texas Instruments Incorporated AIC111 www.ti.com SLAS382 – JUNE 2003 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. The AIC111 comes in a 32-pin QFN 5×5-mm package. A 32-pad solder ball bumped flip chip die that comes in waffle packs or tape and reel is in preview and will be available 3rd quarter 2003. AVAILABLE OPTIONS PART NUMBER PACKAGE AIC111RHB 32-pin QFN (5 mm x 5 mm), in tube. AIC111RHBR 32-pin QFN (5 mm x 5 mm), tape and reel AIC111YE 32-pad waffle scale chip package, bumped die in waffle pack (contact the factory for availability) – Preview, available 3rd quarter 2003 AIC111YER 32-pad (WSCP) bumped die in tape and reel (contact the factory for availability) – Preview, available 3rd quarter 2003 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1)(2) UNIT Input voltage AI or DI pins –0.3 V to 4 V Power supply VDD, power pins Latch-up tolerance JEDEC latch-up (EIA/JEDS78) –0.3 V to 4.5 V 100 mA Operating free-air temperature range, TA 0°C to 70°C Functional temperature range –15°C to 85°C Reflow temperature range (flip chip) 220°C to 230°C Storage temperature range, Tstg –40°C to 125°C Storage humidity 65% R.H. (1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functionaloperation of the device at these or any other conditions beyond those indicated under recommendedoperating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. (2) Specifications are assured operating at maximum device limits for QFN package only, unless otherwise specified. ELECTRICAL CHARACTERISTICS INPUT/OUTPUT, OPERATING TEMPERATURE AT 25°C PARAMETER Digital interface (see Notes 1 and 2) TEST CONDITION MIN VOH High-level output voltage VOL Low-level output voltage Differential Input impedance (AVIN) (see Note 3) Nominal gain = 50x V V BUF_DVDD V V 20 0.87 Microphone bias resistor (MIC_BIAS) 27 Fixed Q DAC full scale output differential Adaptive Q mVpk kΩ 5 20-µA maximum V BUF_DVSS+0.2 450 Input capacitance (AVIN) UNIT BUF_DVDD–0.2 BUF_DVSS Maximum allowed input voltage (AVIN) H bridge amplifier output H-bridge MAX 3.6 VIH High-level input voltage VIL Low-level input voltage Microphone bias voltage (MIC_VSUP) TYP BUF_DVDD (see Note 1) pF 0.94 0.99 29.1 31 V kΩ 3/4 HB_VDD HB_VDD VPP Output resistance Differential, HB – VDD = 1.3 V 20 or 40 Ω (1) DVDD, VDD_OSC, and AVDD should be within 50 mV, preferably connected together. AVSS1, 2, DVSS, and VSS_OSC should be within 50 mV, preferably connected together. (2) Maximum (0.9 V, DVDD –0.5 V) ≤ BUF_DVDD ≤3.6 V (3) Driving single-ended: Rin = R × [(1+A)/(2+A)], A = PGAC Gain (linear), R = 20.4 kΩ for A ≥ 4 or 20.4 kΩ × (4/A) for A<4. Rin(min) = 17 kΩ (A=4), Rin(max) = 59.89 kΩ (A = 0.89), Rin(nom) = 20 kΩ (A = 50). 2 AIC111 www.ti.com SLAS382 – JUNE 2003 2 AVINP 3 AVINM 4 VMID_FILT 5 DVSS2 SCLK 22 BUF_DVSS 21 BUF_DVDD 20 DVDD 19 DVSS1 18 MCLK 11 12 13 14 15 16 17 VOUT_P HB_VDD VOUT_M VSS_OSC HB_VSS_M VOUT_M HB_VDD VOUT_P MIC_BIAS SDOUT HB_VSS_P MIC_VSUP VREF 10 23 VDD_OSC (0,0) Bumped Side SDIN SUB_VSS Alignment Marker AIC111 9 8 7 10 11 12 13 14 15 16 17 6 4 AVINP 3 AVSS2 2 AVSS1 1 32 AIC111 29 28 Bumped View PCB View For exact bump location see Spec. Section 2.2 IMODE MCLK 19 DVSS1 20 DVDD 21 BUF_DVDD 22 BUF_DVSS 23 SDOUT 24 25 26 SDIN FRAME SCLK AVSS_REF 31 30 27 DVSS2 AVINM RST/LBM EXT_RST/PWDN 5 IMODE 18 Back Side AVDD VRFILT VMID_FILT FRAME 25 24 VSS_OSC 7 8 9 26 HB_VSS_P VREF MIC_VSUP 27 SUB_VSS 6 29 28 VDD_OSC MIC_BIAS 31 30 HB_VSS_M AVSS2 EXT_RST/PWDN 32 1 RST/LBM AVSS_REF AVSS1 VRFILT AVDD TERMINAL ASSIGNMENTS Figure 1. AIC111YE Bumped View and PCB Flipped Pin Placements 3 AIC111 www.ti.com AVSS_REF VRFILT AVDD DVSS RST/LBM DVSS SCLK FRAME SLAS382 – JUNE 2003 32 31 30 29 28 27 26 25 AVSS1 1 24 SDIN AVSS2 2 23 SDOUT AVINP 3 22 BUF_DVSS AVINM 4 21 BUF_DVDD AIC111RHB VMID_FILT 5 20 DVDD MIC_BIAS 6 19 DVSS VREF_BG 7 18 MCLK 11 12 13 14 15 16 HB_VSS_P VOUT_P HB_VDD VOUT_M HB_VSS_M SUB_VSS 10 VSS_OSC 17 IMODE 9 VDD_OSC MIC_VSUP 8 Figure 2. AIC111RHB 32-Pin QFN Pinout 4 AIC111 www.ti.com SLAS382 – JUNE 2003 Terminal Functions TERMINAL NO. NAME TYPE DESCRIPTION 1 AVSS1 GND Ground return for ADC analog circuits 2 AVSS2 GND Ground return for PGAC and MIC power analog circuits 3 AVINP AI Noninverting differential analog input coupled through an external 1-µF capacitor to external microphone output 4 AVINM AI Inverting differential analog signal input coupled through an external 1-µF capacitor to ground 5 VMID_FILT AO Midsupply ac ground reference filter pin bypassed by a 1-µF capacitor connected to ground 6 MIC_BIAS AO Source connection of external microphone source follower preamp. (Provides 29.1 kΩ to AVSS2) 7 VREF AO Bandgap reference output bypassed by external 1-µF VREF filter capacitor 8 MIC_VSUP AO Supply voltage for external microphone source follower preamp bypassed with an external 0.1-µF capacitor 9 SUB_VSS GND Isolated substrate VSS for analog circuits 10 VDD_OSC VDD Power pin for internal oscillator 11 VSS_OSC GND Ground return for internal oscillator 12 HB_VSS_P GND Ground return for noninverting stack of H-bridge amplifier 13 VOUT_P AO Noninverting H-bridge output voltage 14 HB_VDD VDD Power pin for H-bridge amplifier 15 VOUT_M AO Inverting H-bridge output voltage 16 HB_VSS_M GND Ground return for inverting stack of H-bridge amplifier 17 IMODE DI Digital interface format selection pin 18 MCLK DO 5-MHz output clock for external DSP/µC 19 DVSS1 GND Ground return for digital circuits 20 DVDD VDD Power pin for digital circuits 21 BUF_DVDD VDD Power pin for interface digital I/O circuits 22 BUF_DVSS GND Ground return for interface digital I/O circuits 23 SDOUT DO Digital interface serial data output pin 24 SDIN DI Digital interface serial data input pin 25 FRAME DO Digital interface serial data framer 26 SCLK DO Digital interface serial shift clock 27 DVSS2 GND Ground return for digital circuits 28 RST/LBM DO Provides external reset and low battery monitor 29 EXT_RST/PWDN DI Powers down all analog blocks and holds digital outputs low until internal system is up 30 AVDD VDD VDD power pin for analog circuits 31 VRFILT AO Positive ADC reference pin bypassed with 1-µF capacitor to AVSS_REF 32 AVSS_REF GND Ground for ADC voltage reference 5 AIC111 www.ti.com SLAS382 – JUNE 2003 AVINP PGA/Compressor AVINM MIC_VSUP MIC_BIAS MIC/Sensor Power and Bias RC Flt Delta Sigma ADC Dec. Filter & HPF Delta Sigma DAC HB_VSS_M HB_VSS_P HB_VDD AVSS VRFILT AVSS_REF AVDD SUB_VSS VMID_FILT FUNCTIONAL BLOCK DIAGRAM H–Bridge Speaker Driver RST/LBM POR Digital Interface 6 DVSS Output Buffers VDD_OSC Oscillator VSS_OSC MCLK SDIN SDOUT FRAME SCLK BUF_DVSS IMODE EXT_RST/PWDN VREF VOUT_M DVDD Biases Generator BUF_DVDD Bandgap Reference VOUT_P AIC111 www.ti.com SLAS382 – JUNE 2003 OPERATION The power source may be a zinc-air battery operating at a typical voltage of 1.3 V. A single external de-coupling capacitor of 1 µF is recommended on the main power supply. VOLTAGE and CURRENT, OPERATING TEMPERATURE AT 25°C PARAMETER TEST CONDITION AVDD, DVDD (All pins of type AVDD, DVDD in pin-out table) MIN TYP 1.1 Steady-state battery supply 1.3 S Unloaded: H-Bridge output open S Microphone resistor model connected (see Figure 6) S Power supplies = 1.3 V S No receiver attached IS (supply current) MAX UNIT 1.5 V µA 350 FUNCTIONAL INPUT CHANNEL PERFORMANCE REQUIREMENTS The front end is defined as the differential signal path from the PGA/compressor inputs, AVINP, and AVINM through the delta-sigma ADC and decimation filter. Typical Conditions; deviations are noted in table. D D D D D D D Operating Temperature Range: 0°C to 70°C. All specification are at 25°C and 1.3 V unless otherwise noted. AVDD, DVDD range: 1.1 V to 1.5 V AVINP, AVINM inputs: AC coupled, Frequency ranging from 100 Hz–10 kHz Measurement Bandwidth: 100 Hz–10 kHz A-weighted. Idle channel definition: AVINP and AVINM are both ac-coupled to AVSS. Typical PGAC gain range is –1 dB to 40 dB. Maximum input voltage: 450 mVpk. PARAMETER TEST CONDITION Broad-band noise Input referred idle channel THD (low level) AVIN ≤ PGAC threshold (see Note 1) DC Offset Idle channel MIN TYP –5 0 0 –10 –2 –20 –4 –30 –6 –40 –50 UNIT µV RMS 0.01 0.2% 0 5 mV 1.2 Gain – dB Gain – dB Droop at 10 kHz Referenced to amplitude at 1 kHz (1) PGAC threshold = PGAC threshold voltage/maximum gain of PGAC. dB –8 –10 –60 –12 –70 –14 –80 –16 –90 –18 –100 MAX 2.4 –20 0 10 20 30 40 50 60 70 f – Frequency – kHz 80 90 100 0 2 4 6 8 10 12 14 16 18 20 f – Frequency – kHz Figure 3. Input Channel Frequency Response With HPF Bypassed 7 AIC111 www.ti.com SLAS382 – JUNE 2003 Analog-to-Digital Converter Filtered Input Voltage Reference Function – Filters analog supply AVDD for DS-ADC reference. With a recommended 0.1-µF external capacitor between pins VRFILT and AVSS_REF, the pole is set at approximately 72 Hz, with 1 µF, the pole is set at approximately 7 Hz. Programmable Gain Amplifier and Compressor Function: The programmable gain amplifier and compressor (PGAC) amplifies the microphone or sensor output signal, provides an appropriate impedance to the microphone buffer or sensor, and provides input gain compression limiting depending on the input signal level if one is not using the fixed gain mode, where the PGAC gain is set by selected register bits. Input compression limiting is discrete automatic gain correction (AGC) based on detecting the peak input signal level using a peak detector circuit that has programmable time responses to provide AGC control, and is intended to prevent a steady state input level up to the defined PGAC limit from being clipped. The attack/release times of the PGAC are programmable by internal clock selection inside the PGAC digital level circuitry that affects the rate of gain changes. The PGAC has four modes of operation: automatic dual-rate (default), automatic single-rate, fixed single-rate, and fixed immediate. Mode selection is controlled by bits 3 and 2 of the PDCREG register. Automatic dual-rate mode (00, default): In this mode of operation, the PGAC has two attack (gain decrease) rates and two release (gain increase) rates, which may be selected by programming the FASTARREG and FORMAT4 registers. Internally, two counters are used to control the compressor gain. The fast rate counter responds at the fast attack and release rates, and it counts down at the attack rate to decrease the PGAC gain if the output of the PGAC is instantaneously larger than a preset threshold (PGAC_THRES = 400-mV peak), or it counts up to increase the gain, up to the maximum allowed gain as set by the PGACREG register, if the output of the PGAC falls below a second threshold, which is 3 dB lower (283-mV peak), which provides hysteresis. Before the gain is allowed to increase, the signal at the output of the PGAC must be below the lower threshold for a period of time which is controlled by bit 4 of PDCREG, and can be 50 ms (0, default) or 25 ms (1). The slow-rate counter responds at the slow attack and release rates, and it attempts to track the state of the fast rate counter. The PGAC gain is determined by whichever counter is smaller. In this way, the PGAC can respond and recover rapidly to short signal bursts while responding more slowly to the signal average. Automatic single-rate mode (01): In this mode of operation, the PGAC has one attack rate and one release rate, which may be selected by programming the FASTARREG register. The operation of the PGAC is similar to the dual-rate mode, except that the slow-rate counter is disabled and the PGAC gain is solely determined by the fast-rate counter. Fixed single-rate mode (10): In this mode of operation, the PGAC gain tracks the value specified in the PGACREG register regardless of the signal amplitude, and changes in PGACREG cause the gain to decrease or increase at the corresponding fast attack or release rate specified in the FASTARREG register. Fixed immediate mode (11): In this mode of operation, the PGAC gain tracks the value specified in the PGACREG register regardless of the signal amplitude, and changes in PGACREG cause the gain to change immediately to the desired gain without stepping through the intermediate gain states. Bit 7 of the PGACREG register controls the PGAC gain read mode. While this bit is low (default), reading PGACREG returns the contents of PGACREG. However, if this bit is set high, then any subsequent read(s) of PGACREG returns the actual, instantaneous PGAC gain. This information may be useful, for example, for dynamic range expansion, effectively undoing the compression effect in the automatic modes of operation. Characteristics: Compression limits the PCAG output. PGACREG is a programmable register. 8 AIC111 www.ti.com SLAS382 – JUNE 2003 Specifications at 25°C, AVDD = 1.3 V PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Input Signal Parameters Maximum signal swing Gain = –1 dB 900 mVPP Block Parameters Gain size step 0.3 0.5 0.7 dB (1) Based on a system clock of 1.280 MHz. (2) For fixed gain mode the rate is 80 KdB/s to new programmed value of gain. All intermediate 0.5 dB gain steps are passed through to reach new gain. Delta Sigma A/D Converter/Anti-alias Filter Function: Converts the PGAC differential output to a digital word with an equivalent dynamic range of approximately 14 bits. Characteristics: The delta sigma ADC has a 64 oversampling ratio, a 1.28-MHz master clock, and a 40-kHz output data rate. Digital coding is 2s complement. Tones are at least 12 dB below broadband noise level. Full-scale signal range corresponds to +215 –1, –215 Specifications at 25°C, AVDD = 1.3 V PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Block parameters Dynamic range –3 dB rel. to reference 87 Input sample rate Output sample rate THD BW: 100 Hz–10 kHz dB 1.28 MHz 40 kHz 85 dB Digital High-Pass Filter Function: Provide a high-pass filter in ADC signal path. The high-pass filter (HPF first order) removes dc offsets introduced into the channel. FORMAT1 register selections for a 50 Hz, 100 Hz, or bypass are available. Characteristics: Programmable selections for a 50 Hz, 100 Hz, or bypass are available. The default HPF pole is 50 Hz. Specifications PARAMETER HPF corner frequency TEST CONDITIONS MIN –3 dB nom mode TYP MAX 50 UNIT Hz Delta Sigma DAC Function: Generates an over-sampled bit string to drive the H-bridge output amplifier such that when filtered reproduces the desired analog waveform. Characteristics: A 32 times over-sampled modulator multi-bit design. Specifications PARAMETER fd(input_data) fclk TEST CONDITIONS Signal; BW = 10 kHz MIN TYP MAX UNIT 40 kHz 640 kHz 9 AIC111 www.ti.com SLAS382 – JUNE 2003 H-bridge Output Driver Function: An H-bridge output driver efficiently converts the delta sigma DAC modulator output signals. The external load provides the low-pass filtering that recovers the differential analog signal from the H-bridge. Characteristics: Standard H-bridge configuration with transistors sized to differentially drive the load impedance. The load impedance is complex and a function of frequency. H-Bridge Load Switching Noninverting Phase Inverting Phase VDD ( vbat) VDD (vbat) OUTMM OUTPM OUTP Receiver Load OUTM OUTPP OUTMP OUTMM OUTPM OUTP Receiver Load OUTM OUTPP OUTMP AVSS AVSS NOTE: VDD does not necessarily have to be connected to the same potential as AVDD, it could be connected to a higher potential than AVDD, equal to AVDD, but not less than AVDD. Figure 4. Definition of Phase and Output Switching Current Polarity Specifications at 25°C, HB_VDD = 1.3 V PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Block Parameters DC offset Idle channel; Differential across VOUT_P and VOUT_M Broadbandnoise Broadband noise Idle channel, measured at output out ut of channel, BW = 100 Hz–10 kHz, HB_VDD = 1.3 V, A-weighted THD BW = 100 Hz–10 kHz –5 33 Adaptive Q 12 640 Fixed Q 10 5 mV µVrms Vrms 0.03% Switching frequency Maximum output swing 0 Fixed Q Adaptive Q kHz 3/4 HB_VDD HB_VDD VPP AIC111 www.ti.com SLAS382 – JUNE 2003 Microphone Power Supply Function: The microphone power supply circuit provides a constant power supply voltage and bias current for the microphone preamp or sensor bias, provides a low-noise voltage reference (ac ground) for the PGAC, provides regulated PGAC comparator threshold levels, provides bandgap regulated POR comparator trip voltage levels, and provides a bandgap regulated current for the biases generator circuit. Characteristics: The low-dropout regulator configuration or single stage, single-pole amplifier drives an external 0.1-µF capacitor. The regulator does not oscillate under no-load or loaded conditions. The circuit supplies up to 50-µA of continuous current. Specifications at 25°C, AVDD = 1.3 V PARAMETER TEST CONDITIONS MIN VMID_FILT IL = 20 µA 0.59 × AVDD PSRR 0.1-µF external bypass cap from MIC_VSUP to AVSS2. MIC_VSUP 0.87 Output impedance TYP 0.94 MAX 0.97 UNIT V 0.78 V 55 dB 1.5 kΩ MCLK Output Function: Provides a clock signal for external use. Specifications at 25°C, VDD_OSC, DVDD, BUF_DVDD = 1.3 V PARAMETER TEST CONDITIONS MIN Frequency 4.7 Jitter RMS jitter TYP 5.12 MAX UNIT 5.5 MHz 150 Duty cycle ps 50% Power-On Reset Function: Provides a reset signal upon power up (stable voltage reference) that initializes the digital interface. It also provides a gating signal to the delta-sigma DAC modulator to prevent audible pops and clicks from erroneous data sent to the H-bridge circuit at power up and during periods when battery voltage has degraded below 1.05 V for an extended period of time (typically greater than 44 µs). The reset signal is asynchronous to MCLK. Digital interface does not start operating until after t(VDD)_valid has transpired. POR has to: D D D D Deal with system’s on/off switch bounce lasting 100 ms or less. Detect when the power supply AVDD is ≥1.1 V to enable the H-bridge output. Provide kick-start to oscillator. Detect when VDD degrades below 1.05 V for a period of time that is nontransient, and gate H-bridge output. Specifications at 25°C, AVDD = 1.3 V PARAMETER TEST CONDITIONS MIN TYP MAX UNIT t(VDD)_valid: Time VDD considered valid at powerup after switch bounce has settled. VDD > 1.1 V 100 ms Allowed transient spike below 1.05 V before H-bridge output and digital interface are not asserted. VDD < 1.05 V 44 µs POR on 1.1 POR off 1.05 V 11 AIC111 www.ti.com SLAS382 – JUNE 2003 DIGITAL INTERFACE Function: The digital interface can be selected (IMODE=LOW) as a serial audio/control interface (SACI), which is the McBSP DSP-codec protocol, or (IMODE=HIGH), a serial peripheral interface (SPI). Either SACI or SPI sends out a 16-bit audio stream from the ∆–Σ ADC and receives a 20-bit audio stream going to the ∆–Σ DAC/H-Bridge. Several control functions, READ/WRITE to user registers, are also included totaling five 8-bit registers. Four pins, SCLK, FRAME, SDIN and SDOUT, are employed in SACI or SPI. An internal register map exists that contains read/write program registers for a variety of FORMAT (user) settings. The register bits that are designated not used will always read back zero or voltage level VSS regardless of what is written to them. DIG INTERFACE PIN I/O DESCRIPTION SCLK Output Bit shift clock. SCLK has an internal pull down. FRAME Output Data frame sync: controls the separation of audio channels and provides a reset/synchronization to the interface’s internal state machine. FRAME has an internal pull down. SDIN Input Serial audio/control data input pin. SDOUT Input Serial audio/control data output pin. IMODE Input Interface protocol selection pin. LOW=SACI, HIGH=SPI. MCLK Output Clock output pin. SLAVE MASTER SDOUT DR FRAME FSX FSR AIC111 SDIN DX SCLK CLKR CLKS CLKX MCLK C54x CLKIN (See Note A) NOTE A: The dotted line indicates the connection is not essential for communication to work. Figure 5. AIC111 McBSP DSP-Codec Interface McBSP DSP-Codec (SACI) Protocol Use this protocol when interfacing to TI DSPs. D The SACI works in a master mode. D SCLK = 1.28 MHz. FRAME (= 40 kHz) has a 50% duty cycle. FRAME is an output. D 32-bit control/audio data, written on the SDIN pin, consist of a 20-bit audio word going to the ∆–Σ DAC, and a 12-bit control word. D DAC input has two modes of operation, a 20-bit mode, and a 16-bit mode. D The 12-bit control word consists of: a R/W bit, 3 address bits, and 8-bits of control register content. Note that the R/W bit is defined as 0=READ, and 1=WRITE. D When the 3 address bits are all zeros, the control function of the SACI is disabled. D 24-bit audio/control data, read from the SDOUT pin, consist of one 16-bit output from the ∆–Σ ADC followed by an 8-bit control word. D All data/control words are formatted as the MSB first. 12 AIC111 www.ti.com SLAS382 – JUNE 2003 20-Bit Mode D/A Input D19 – D0 AIC111 Input D19 – D0 16-Bit Mode D19 – D0 D/A Input AIC111 Input D19 D19 D19 D19 D19 – D4 D19 D19 D19 D19 – D4 0 Shift = 1 D19 D19 D19 – D4 0 0 Shift = 2 D19 D19 – D4 0 0 0 Shift = 3 D19 – D4 0 0 0 0 Shift = 4 D18 – D4 0 0 0 0 0 Shift = 0 Shift = 5 See Note B NOTE B: For 5-bit left shift, digital word is limited to 15 bits with sataration. Figure 6. AIC111 Data Output 13 AIC111 SLAS382 – JUNE 2003 14 Figure 7. AIC111 DSP-Codec (SACI) Signals (Read = 0, Write = 1) FRAME SCLK 1 SDIN SDOUT 2 3 4 5 6 7 8 9 10 11 12 13 14 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D15 D14 D13 D12 D11 D10 D9 D4 D3 D8 D7 D6 D5 15 16 D5 D4 D2 D1 D0 17 18 D3 D2 19 20 21 22 23 24 25 26 27 28 29 30 31 32 D1 D0 W/R A2 A1 A0 C7 C6 C5 C4 C3 C2 C1 C0 D19 D18 C7 C6 C5 C4 C3 C2 C1 C0 D15 D14 www.ti.com AIC111 www.ti.com SLAS382 – JUNE 2003 SLAVE GPIO MASTER AIC111 FRAME STE SDOUT SIMO SDIN SOMI SCLK UCLK MCLK MCLK MSP430x Figure 8. AIC111 SPI I/O Diagram SPI Protocol D AIC111 can also implement a master SPI protocol. D SCLK supplies a bit shift clock of 1.28 MHz to the SPI port of a slave device. D FRAME must be in the active low state prior to data transaction and must stay low for the duration of data transaction. Before communication, there are eight silent cycles on SCLK. During this period FRAME also sends a pulse to reset the slave device. D When the control function is not required, the AIC111 transmits a 16-bit audio word to and receives a 20-bit audio word from the slave device in every FRAME cycle. D A WRITE/READ of an 8-bit user register (address 0x01 to 0x07) takes two FRAME cycles. D All data/control words are formatted as the MSB first. 15 AIC111 www.ti.com D0 D3 D2 D1 D4 D8 D7 D6 D5 D15 D14 D13 D12 D11 D10 D9 D4 D7 D6 D5 D8 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 Don’t Care SDOUT SDIN SCLK FRAME 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 D3 D2 D1 27 28 29 D0 W/R A2 30 A1 31 A0 32 SLAS382 – JUNE 2003 NOTE: If A2, A1, and A0 = 0, one gets audio data only and W/R is a don’t care. If in the previous frame A2, A1, and A0 = 0, then one gets both audio and control data depending on the W/R bit defined as Read = 0 and Write = 1. Figure 9. AIC111 SPI Signals 16 SDOUT SDIN SCLK FRAME 31 32 1 2 3 5 Don’t Care 4 6 7 8 13 14 15 16 17 18 19 20 D8 D7 D6 D5 D4 12 D15 D14 D13 D12 D11 D10 D9 11 D8 10 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 9 D0 24 D3 D2 D1 23 D4 22 D7 D6 D5 21 26 27 C7 C6 C5 C7 C6 C5 25 30 31 C0 32 C1 C0 C3 C2 C1 29 C4 C3 C2 C4 28 www.ti.com SLAS382 – JUNE 2003 AIC111 NOTE: SDIN shows writing to A2, A1, and A0 specified from the previous frame. SDOUT shows reading from A2, A1, and A0 specified from a different previous frame. Figure 10. AIC111 SPI Signals 17 AIC111 www.ti.com SLAS382 – JUNE 2003 Digital Interface Timing PARAMETER F_sclk SCLK frequency F_frame FRAME frequency MIN TYP MAX 1.28 MHz F-sclk/32 MHz Digital Interface Block Diagram PGA/Compressor ADC SCLK FRAME DAC/H–Bridge SDIN CONTROL REGISTERS McBSP/SPI CONTROL LOGIC SDOUT DATA BLOCK Oscillator IMODE MCLK Power–on Reset Mic Power/VREF Register Map and Register Bit Definitions ADDRESS REGISTER NAME 0x00 Reserved 0x01 PGACREG 0x02 HPFSFTREG HPF and shift control register 0x03 PDCREG Power-down control register 0x04 FASTARREG Fast attack/release rate control register 0x05 SLOWARREG Slow attack/release rate control register 0x06–07 Reserved NOTE: Do not write to the reserved registers. 18 DETAILED DESCRIPTION Reserved for future use PGAC gain register Reserved for future use UNIT AIC111 www.ti.com SLAS382 – JUNE 2003 PGACREG BIT NAME 7 PGAC_READ_MODE Select register contents or actual gain to read 0: Read FORMAT0 register contents (default) 1: Read actual PGAC gain PGAC_GAIN [6:0] PGAC gain adjustment (0.5 dB steps). A full table is found in the Appendix Section of this data sheet. 0x52 = +40.0 dB 0x51 = +39.5 dB 0x50 = +39.0 dB … 0x46 =+34.0 dB (default) …. 0x01 = –0.5 dB 0x00 = –1.0 dB 6:0 FUNCTION DEFAULT=0x46 HPFSFTREG BIT 7 NAME FUNCTION DBUFF_EN Enable weak (1/2 strength) dig I/O buffer 6:5 HPF_CTL [1:0] Control bits for high-pass filter 00: normal mode 01: HPF bypass 10: 100 Hz corner frequency 11: Not used 4:2 SHIFT [2:0] Select shift bits when ADC 16-b output is used as DAC 20-b input. 000: no shift –24 db gain 001: 1b left shift –18 dB gain 010: 2b left shift –12 dB gain 011: 3b left shift –6 dB gain 100: 4b left shift (default) 0 dB gain 101: 5b left shift +6 dB gain 11X: 5b left shift 1:0 DAC_MODE Select DAC mode of operation. 00: DAC off, powered down 01: 16-bit input goes through shifter (default) 10: 20-bit input bypasses shifter 11: ADC→DAC digital loopback DEFAULT=0x11 PDCREG BIT NAME FUNCTION 7 DAC_ADAPTIVE_Q 0 = fixed quantization, 1 = adaptive quantization 6 HB_OUT_EN H-bridge output enable 5 HB_DRIVE H-bridge drive strength, 0 = 40 Ω, 1 = 20 Ω 4 HIST_TIMEOUT_SEL PGAC hysteresis timeout select 0: 50 ms (default) 1: 25 ms 3:2 PGAC_GAIN_MODE Set gain mode of PGAC 00: Automatic, dual rate (default) 01: Automatic, single rate 10: Fixed, single rate 11: Fixed, immediate 1 MIC_VSUP_PD Power down MIC_VSUP 0 FRONTEND_PD Power down PGAC+ADC DEFAULT=0x00 19 AIC111 www.ti.com SLAS382 – JUNE 2003 FASTARREG PGAC Fast Rates BIT NAME 7:4 ATTACK<7:4> FUNCTION 1111: Attack rate = 80000 dB/s 1110: Attack rate = 40000 dB/s 1101: Attack rate = 20000 dB/s 1100: Attack rate = 10000 dB/s 1011: Attack rate = 5000 dB/s 1010: Attack rate = 2500 dB/s 1001: Attack rate = 1250 dB/s 1000: Attack rate = 625 dB/s 0111: Attack rate = 312.5 dB/s 0110: Attack rate = 156.25 dB/s 0101: Attack rate = 78.13 dB/s 0100: Attack rate = 39.1 dB/s 0011: Attack rate = 19.53 dB/s 0010: Attack rate = 9.77 dB/s 0001: Attack rate = 4.88 dB/s 0000: Attack rate = 2.44 dB/s 3:0 RELEASE<3:0> 1111: Release rate = 80000 dB/s 1110: Release rate = 40000 dB/s … 0001: Release rate = 4.88 dB/s 0000: Release rate = 2.44 dB/s DEFAULT=0xF7 SLOWARREG PGAC Slow Rates (Dual Rate Mode Only) 20 BIT NAME FUNCTION 7:4 ATTACK<7:4> 1111: Attack rate = 80000 dB/s 1110: Attack rate = 40000 dB/s … 0001: Attack rate = 4.88 dB/s 0000: Attack rate = 2.44 dB/s 3:0 RELEASE<3:0> 1111: Release rate = 80000 dB/s 1110: Release rate = 40000 dB/s … 0001: Release rate = 4.88 dB/s 0000: Release rate = 2.44 dB/s DEFAULT=0x42 AIC111 www.ti.com SLAS382 – JUNE 2003 APPENDIX PGAC GAIN PGAC GAIN VALUES PGAC PGAC BUS NAME HEX VALUE BINARY PGAC_GAIN<6:0> _ 0x52 1010010 40 0x51 1010001 39.5 0x50 1010000 39 0x4F 1001111 38.5 PGAC_GAIN<6:0> _ GAIN (DB) 0x4E 1001110 38 0x4D 1001101 37.5 0x4C 1001100 37 0x4B 1001011 36.5 0x4A 1001010 36 0x49 1001001 35.5 0x48 1001000 35 0x47 1000111 34.5 0x46 1000110 34 0x45 1000101 33.5 0x44 1000100 33 0x43 1000011 32.5 0x42 1000010 32 0x41 1000001 31.5 0x40 1000000 31 30.5 0x3F 0111111 0x3E 0111110 30 0x3D 0111101 29.5 0x3C 0111100 29 0x3B 0111011 28.5 0x3A 0111010 28 0x39 0111001 27.5 0x38 0111000 27 0x37 0110111 26.5 0x36 0110110 26 0x35 0110101 25.5 0x34 0110100 25 0x33 0110011 24.5 0x32 0110010 24 0x31 0110001 23.5 0x30 0110000 23 22.5 0x2F 0101111 0x2E 0101110 22 0x2D 0101101 21.5 0x2C 0101100 21 0x2B 0101011 20.5 0x2A 0101010 20 0x29 0101001 19.5 0x28 0101000 19 0x27 0100111 18.5 0x26 0100110 18 0x25 0100101 17.5 0x24 0100100 17 0x23 0100011 16.5 21 AIC111 www.ti.com SLAS382 – JUNE 2003 PGAC GAIN VALUES PGAC ((Continued)) PGAC BUS NAME HEX VALUE BINARY PGAC_GAIN<6:0> _ 0x22 0100010 16 0x21 0100001 15.5 0x20 0100000 15 0x1F 0011111 14.5 PGAC_GAIN<6:0> _ Default 22 GAIN (DB) 0x1E 0011110 14 0x1D 0011101 13.5 0x1C 0011100 13 0x1B 0011011 12.5 0x1A 0011010 12 0x19 0011001 11.5 0x18 0011000 11 0x17 0010111 10.5 0x16 0010110 10 0x15 0010101 9.5 0x14 0010100 9 0x13 0010011 8.5 0x12 0010010 8 0x11 0010001 7.5 0x10 0010000 7 0x0F 0001111 6.5 0x0E 0001110 6 0x0D 0001101 5.5 0x0C 0001100 5 0x0B 0001011 4.5 0x0A 0001010 4 0x09 0001001 3.5 0x08 0001000 3 0x07 0000111 2.5 0x06 0000110 2 0x05 0000101 1.5 0x04 0000100 1 0x03 0000011 0.5 0x02 0000010 0 0x01 0000001 –0.5 0x00 0000000 –1 AIC111 www.ti.com SLAS382 – JUNE 2003 VCC ZINC AIR BATTERY 1.3V VSS BUF_DVDD AVDD DVDD TI TMS320C54xx APPLICATION CIRCUIT MIC_VSUP SCLK MIC_BIAS CLKR CLKS CLKX SDIN DX Microphone AIC111 B U F F E R S 1.3V H B R I D G E HB_VDD HB_VSS Speaker I/O SDOUT DR M c B S P ’C54x FRAME FSX FSR RST/LBM MCLK RST CLKIN BUF_DVSS DVSS AVSS EXT_RST/PWDN LBM = Low Battery Monitor Figure 11. Interfacing to the TMS320C54xx for a Hearing Aid Application Required external capacitors: D D D D D 1-µF coupling capacitor on AVINP, AVINM 1-µF from VMID_FILT to analog ground 1-µF from VREF to analog ground 0.1-µF from MIC_VSUP to analog ground At least 0.1-µF from VRFILT to analog ground. 1-µF from VRFILT to analog ground is recommended. 23 AIC111 www.ti.com SLAS382 – JUNE 2003 2.8 V VCC VSS DVDD AVDD 1.3 V BUF_DVDD TI MSP430F12x APPLICATION CIRCUIT P2.5 (See Note A) MIC_VSUP MIC_BIAS Microphone SCLK INCLK SDIN SOMI SDOUT SIMO FRAME STE MSP430F12x I/O AIC111 Speaker B U F F E R S RST/LBM XIN BUF_DVSS DVSS AVSS MCLK RST/NMI LBM = Low Battery Monitor ’430 Can Also Use EXT_RST/PWDN to Reset or Power Down the AIC111 Note A: P2.5 enables the MSP430F12x to shut down the AIC111 when desired. Figure 12. Interfacing to the MSP430F12x for a Hearing Aid Application 24 AIC111 www.ti.com SLAS382 – JUNE 2003 MECHANICAL AND ENVIRONMENTAL Packaging The AIC111 is available in a 32-pin quad QFN 5x5-mm package. The AIC111 will be available 3rd quarter 2003 as bare solder ball bumped die intended for direct PCB mounting (also known as wafer scale packaging). D D D D For QFN packaged part in tubes order: AIC111RHB. For QFN packaged part in tape and reel order: AIC111RHBR. For ball bumped die (in waffle pack) order: AIC111YE (Preview, available 3rd quarter 2003). For ball bumped die (in tape and reel) order: AIC111YER (Preview, available 3rd quarter 2003). BOND PAD PITCH AND DIE AREA X = 2737.62 µ, Y = 3175.02 µ, (107.78 mil, 125.0 mil) (2,74 mm, 3,18 mm) 13.47kmil2 (8.69mm2) Die dimensions Maximum die area (includes scribe area) 202.95 µ or 7.99 mil Minimum bond pad pitch Nearest PAD (#) 7 30 12 14 16 28 18 20 21 22 25 9 10 23 1 32 4 27 17 6 2 3 PITCH PAD (#) 8 31 13 15 15 29 19 19 20 21 26 10 11 24 32 1 5 28 16 7 1 2 (micron) (mil) 202.950 202.950 237.690 237.690 237.690 241.200 256.410 256.410 256.410 256.410 287.651 295.470 295.470 306.360 327.147 327.147 356.940 357.034 359.453 369.450 371.520 380.700 (7.990) (7.990) (9.358) (9.358) (9.358) (9.496) (10.095) (10.095) (10.095) (10.095) (11.325) (11.633) (11.633) (12.061) (12.880) (12.880) (14.053) (14.056) (14.152) (14.545) (14.627) (14.988) 25 AIC111 www.ti.com SLAS382 – JUNE 2003 Number of pins 32 Pad locations: Bond Pad Coordinates Units: microns Dimensions: X = 2737.62 Y = 3175 Bond pad origin: X = 0.000 Y = 0.000 Bond pad offset: X = 0.000 Y = 0.000 (X,Y) = (0,0) is located at the left bottom of the die by pads 8 and 9. See section 1.6, Figure 1–1. Bond Pad Dimensions Pad # Xcenter Ycenter Diameter 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 154.080 154.080 154.080 154.080 154.080 154.080 154.080 154.080 410.310 705.780 1001.250 1327.860 1565.550 1803.240 2040.930 2278.620 2574.990 2574.990 2574.990 2574.990 2574.990 2574.990 2574.990 2574.990 2574.990 2371.590 1910.430 1553.850 1312.650 955.530 752.580 410.310 2808.990 2437.470 2056.770 1676.070 1319.130 938.430 568.980 366.030 162.630 162.630 162.630 162.630 162.630 162.630 162.630 162.630 366.030 782.550 1038.960 1295.370 1551.780 1808.190 2188.890 2495.250 2808.990 3012.390 2994.390 3012.390 3012.390 3012.390 3012.390 3012.390 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 70.020 DIE THICKNESS Final die thickness Z (without solder bump) TYPICAL TOLERANCE 29.59 mil or 725 µm ±0.79 mil or 20 µm SOLDER BUMP D Bump metal composition: 37% Pb (lead)/63% Sn (tin) D Type: Spherical BUMP SPEC. Bump height Re-flow temperature TYPICAL TOLERANCE 100 µm +8 µm NOTE Tolerance across a single die. +16 µm Tolerance across any wafer. 183°C WAFFLE SCALE PACKAGE DISCLAIMERS FOR AIC11YE AND AIC11YER D The AIC111’s die bond pads, their peripheral placement, passivation opening, and layout are in accordance with ASE’s Bumping Design Guide revision D, June, 2001. D The final application is assumed to use plastic overmolding where the die is hermetically sealed, and the maximum ratings apply only to the QFN package and not to the WSCP. 26 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty AIC111RHB ACTIVE QFN RHB 32 AIC111RHBR ACTIVE QFN RHB AIC111RHBRG4 ACTIVE QFN AIC111YE ACTIVE AIC111YER ACTIVE 73 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 32 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR RHB 32 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XCEPT YE 32 39 TBD Call TI Call TI XCEPT YE 32 1000 TBD Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated WWW.ALLDATASHEET.COM Copyright © Each Manufacturing Company. All Datasheets cannot be modified without permission. This datasheet has been download from : www.AllDataSheet.com 100% Free DataSheet Search Site. Free Download. No Register. Fast Search System. www.AllDataSheet.com