TI TLV320AIC1110GQER

TLV320AIC1110
SLAS359 – DECEMBER 2001
PCM CODEC
Capable of Driving 32 Ω Down to a 8-Ω
FEATURES
2.7-V to 3.3-V Operation
Designed for Analog and Digital Wireless
Speaker
Handsets and Telecommunications
Applications
Two Differential Microphone Inputs
Differential Earphone Outputs and One
Single-Ended Earphone Output
Earphone and Microphone Mute
Programmable Transmit, Receive, and
Sidetone Paths With Extended Gain and
Attenuation Ranges
Programmable for 15-Bit Linear Data or 8-Bit
Companded (µ-law and A-law) Mode
Supports PCM Clock Rates of 128 kHz and
2.048 MHz
Pulse Density Modulated (PDM) Buzzer
Output
On-Chip I2C Bus, Which Provides Simple,
Standard, Two-Wire Serial Interface With
Digital ICs
Dual-Tone Multifrequency (DTMF) and
Single-Tone Generator Capable of up to 8-kHz
Tone With Three Selectable Resolutions of
7.8125 Hz, 15.625 Hz, and 31.25 Hz
2-Channel Auxiliary Multiplexer (MUX) (Analog
Switch)
Programmable Power Down Modes
Pin Compatible to the TLV320AIC1103 and
TLV320AIC1109 Devices for TQFP Only
Available in a 32-Pin Thin Quad Flatpack
(TQFP) Package and MicroStar Junior BGA
APPLICATIONS
Digital Handset
Digital Headset
Cordless Phones
Digital PABX
Digital Voice Recording
DESCRIPTION
The TLV320AIC1110 provides extended gain and
attenuation flexibility for transmit, receive, and sidetone
paths. A differential earphone output is capable of
driving speaker loads as low as 8 Ω for use in speaker
phone applications. The single tone function on the
TLV320AIC1110 generates a single tone output of up to
8 kHz. The resolution of the DTMF tone is also
selectable to 7.8125 Hz, 15.625 Hz, or 31.25 Hz through
the interface control. The analog switch provides more
control capabilities for voice-band audio processor
(PCM codec).
This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These
circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C,
Method 3015; however, it is advised that precautions be taken to avoid application of any voltage higher than maximum-rated
voltages to these high-impedance circuits. During storage or handling, the device leads should be shorted together or the device
should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriated logic voltage level,
preferably either VCC or ground. Specific guidelines for handling devices of this type are contained in the publication Guidelines for
Handling Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
†These options are available on some devices. Please see the table of comparison for the last two generations of PCM codecs.
MicroStar Junior is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
1
TLV320AIC1110
SLAS359 – DECEMBER 2001
DESCRIPTION (Continued)
The PCM codec is an analog-digital interface for voice band signals designed with a combination of coders and
decoders (codecs) and filters. It is a low-power device with companding options and programming features, and
it meets the requirements for communication systems, including the cellular phone. The device operates in
either the 15-bit linear or 8-bit companded (µ-law or A-Law) mode, which is selectable through the I2C interface.
A coder, an analog-to-digital converter or ADC, digitizes the analog voice signal, and a decoder, a
digital-to-analog converter or DAC, converts the digital-voice signal to an analog output. The PCM codec
provides a companding option to overcome the bandwidth limitations of telephone networks without degrading
the sound quality. The human auditory system is a logarithmic system in which high amplitude signals require
less resolution than low amplitude signals. Therefore, an 8-bit code word with nonuniform quantization (µ-law
or A-law) has the same quality as 13-bit linear coding. The PCM codec provides better digital code words by
generating a 15-bit linear coding option.
The human voice is effective from a frequency range of 300 Hz to 3300 Hz in telephony applications. In order
to eliminate unwanted signals, the PCM codec design has two types of filters that operate in both the transmit
and receive path. A low-pass filter attenuates the signals over 4 kHz. A selectable high-pass filter cleans up the
signals under 100 Hz. This reduces noise that may have coupled in from 50/60-Hz power cables. The high-pass
filter is bypassed by selecting the corresponding register bit.
The PCM codec has many programming features that are controlled using a 2-wire standard serial I2C interface.
This allows the device to interface with many digital ICs such as a DSP or a microprocessor. The device has
seven registers: power control, mode control, transmit PGA, receive PGA, high DTMF, low DTMF, and auxiliary
mode control. Some of the programmable features that can be controlled by I2C interface include:
Transmit amplifier gain
Receive amplifier gain
Sidetone gain
Volume control
Earphone control
PLL power control
Microphone selection
Transmit channel high-pass filter control
Receive channel high-pass filter control
Companding options and selection control
PCM loopback
DTMF control
Pulse density modulated control
The PCM codec is also capable of generating its own internal clocks from a 2.048-MHz master clock input.
2
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PLLVSS
VSS
MCLK
RESET
PWRUPSEL
BUZZCON
PCMSYN
PCMCLK
PBS PACKAGE
(TOP VIEW)
24 23 22 21 20 19 18 17
25
16
26
15
14
13
PCMO
PCMI
DVSS
DVDD
12 SCL
11 SDA
10 MUXOUT2
9 MUXOUT1
27
28
29
30
31
32
1
2
3
4 5 6 7
8
MBIAS
MIC1P
MIC1N
MIC2P
MIC2N
REXT
MUXIN
AVSS
PLLVDD
EARVSS
EAR1ON
EARVDD
EAR1OP
EARVSS
EAR2O
AVDD
www.ti.com
3
TLV320AIC1110
SLAS359 – DECEMBER 2001
EAR1OP
EARVDD
EAR1ON
EARVSS
PLLVDD
PLLVSS
2
3
4
5
6
7
8
9
B
NC
NC
NC
NC
NC
NC
NC
VSS
C
NC
NC
NC
NC
NC
NC
MCLK
D
NC
NC
NC
NC
NC
NC
NC
RESET
E
NC
NC
NC
NC
NC
NC
NC
PWRUPSEL
F
NC
NC
NC
NC
NC
NC
NC
G
NC
NC
NC
NC
NC
NC
NC
H
NC
NC
NC
NC
NC
NC
NC
EAR2O
EARVSS
MicroStar Junior (GQE) PACKAGE
(TOP VIEW)
1
REXT
MUXIN
J
4
BUZZCON
PCMSYN
PCMCLK
PCMO
MUXOUT1
AVSS
www.ti.com
PCMI
MIC2N
DVSS
MIC2P
DVDD
MIC1N
SCL
MIC1P
SDA
MBIAS
A
MUXOUT2
AVDD
PCMOUT
PCMSYN
PCMCLK
RX Vol
Control
g = –18 dB
to
0 dB
MIC1P
PCM
Interface
MIC1N
MIC
Amplifier
2
g=6
or
18 dB
MIC
Amplifier
1
g=
23.5 dB
Analog
Modulator
Voice
0 dB
or
6 dB
RX Filter
and PGA
g = – 6 dB
to
+6 dB
TX Filter
and PGA
g = –10 dB
to
0 dB
www.ti.com
Sidetone
g = –24 db
to
–12 dB
MIC2P
Ear
Amp1
EAR1OP
EAR1ON
Digital
Modulator
and Filter
DTMF
GAIN
MUX
DTMF
–12 to
12 dB
in 6dB
Steps
MIC2N
functional block diagram
PCMIN
Ear
Amp2
EAR2O
Control Bus
DTMF
OUT
IN
Buzzer
Control
MUX
OUT
BUZZCON
Generator
2
I C
I/F
REF
PLL
Power and RESET
TLV320AIC1110
SLAS359 – DECEMBER 2001
PWRUPSEL
V SS
AVDD
AV SS
DVDD
DV SS
PLLVDD
PLLV SS
EARVDD
EARV SS
RESET
MCLK
REXT
MBIAS
SDATA
SCLK
5
TLV320AIC1110
SLAS359 – DECEMBER 2001
detailed description
power on/reset
The power for the various digital and analog circuits is separated to improve the noise performance of the
device. An external reset must be applied to the active low RESET terminal to assure reset upon power on and
to bring the device to an operational state. After the initial power-on sequence, the device can be functionally
powered up and powered down by writing to the power control register through the I2C interface. The device
has a pin-selectable power up in the default mode option. The hardwired pin-selectable PWRUPSEL function
allows the PCM codec to power up in the default mode and to be used without a microcontroller.
reference
A precision band gap reference voltage is generated internally and supplies all required voltage references to
operate the transmit and receive channels. The reference system also supplies bias voltage for use with an
electret microphone at terminal MBIAS. An external precision resistor is required for reference current setting
at terminal REXT.
I2C control interface
The I2C interface is a two-wire bidirectional serial interface. The I2C interface controls the PCM codec by writing
data to seven control registers:
Power control
Mode control
Transmit PGA and sidetone control
Receive PGA gain and volume control
DTMF routing
Tone selection control
Auxiliary control
There are two power-up modes which may be selected at the PWRUPSEL terminal: (1) The PWRUPSEL state
(VDD at terminal 20) causes the device to power up in the default mode when power is applied. Without an I2C
interface or controlling device, the programmable functions are fixed at the default gain levels, and functions
such as the sidetone and DTMF are not accessible. (2) The PWRUPSEL state (ground at terminal 20) causes
the device to go to a power-down state when power is applied. In this mode, an I2C interface is required to power
up the device.
phase-locked loop (PLL)
The phase-lock loop generates the internal clock frequency required for digital filters and modulators by phase
locking to 2.048-MHz master clock input.
PCM interface
The PCM interface transmits and receives data at the PCMO and PCMI terminals respectively. The data is
transmitted or received at the PCMCLK speed once every PCMSYN cycle. The PCMCLK can be tied directly
to the 128-kHz or 2.048-MHz master clock (MCLK). The PCMSYN can be driven by an external source or
derived from the master clock and used as an interrupt to the host controller.
microphone amplifiers
The microphone input is a switchable interface for two differential microphone inputs. The first stage is a
low-noise differential amplifier that provides a gain of 23.5 dB. The second-stage amplifier has a selectable gain
of 6 dB or 18 dB.
6
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
detailed description (continued)
analog modulator
The transmit channel modulator is a third-order sigma-delta design.
transmit filter and PGA
The transmit filter is a digital filter designed to meet CCITT G.714 requirements. The device operates either in
the 15-bit linear or 8-bit companded µ-law or in the A-law mode, which is selectable through the I2C interface.
The transmit PGA defaults to 0 dB.
sidetone
A portion of the transmitted audio is attenuated and fed back to the receive channel through the sidetone path.
The sidetone path defaults to the mute condition. The default gain of -12 dB is set in the sidetone control register.
The sidetone path can be enabled by writing to the power control register.
receive volume control
The receive volume control block acts as an attenuator with a range of –18 dB to 0 dB in 2-dB steps for control
of the receive channel volume. The receive volume control gain defaults to 0 dB.
receive filter and PGA
The receive filter is a digital filter that meets CCITT G.714 requirements with a high-pass filter that is selectable
through the I2C interface. The device operates either in the 15-bit linear or the 8-bit µ-law or the A-law
companded mode, which is selectable through the I2C interface. The gain defaults to –4 dB, representing a
3-dBm level for a 32-Ω load impedance and the corresponding digital full scale PCMI code.
digital modulator and filter
The second-order digital modulator and filter convert the received digital PCM data to the analog output required
by the earphone interface.
earphone amplifiers
The analog signal can be routed to either of two earphone amplifiers, one with differential output (EAR1ON and
EAR1OP) and one with single-ended output (EAR2O). Clicks and pops are suppressed for EAR1 differential
output only.
tone generator
The tone generator provides generation of standard DTMF tones which are output to (1) the buzzer driver, as
a PDM signal, (2) the receive path DAC for outputting through the earphone, or (3) as PCMO data. The integer
value is loaded into one of two 8-bit registers, the high-tone register (04), or the low-tone register (05) (see the
Register Map Addressing section). The tone output is 2 dB higher when applied to the high tone register (04).
The high DTMF tones must be applied to the high-tone register, and the low DTMF tones to the low-tone register.
The tone signals can be generated with three different resolutions at ∆F= 7.8125 Hz, 15.625 Hz, and 31.250 Hz.
The resolution option can be selected by setting the register (06).
analog mux
The analog switch can be used to source an analog signal to two different loads. The output can be reselected
by setting the auxiliary register (06).
www.ti.com
7
TLV320AIC1110
SLAS359 – DECEMBER 2001
detailed description (continued)
DTMF gain MUX
The DTMF gain MUX selects the signal path and applies the appropriate gain setting. Therefore the device is
either in tone mode or in voice mode. When set in the voice mode, the gain is controlled by the auxiliary register
and is set to 0 dB or 6 dB. When set in the tone mode, the gain is from –12 dB to 12 dB in 6-dB steps which
is set by the volume control register. The gain setting is controlled by the RXPGA register. This will not create
any control contention since the device is working in one mode at a time.
Terminal Functions
TERMINAL†
NAME
NO.
I/O
DESCRIPTION
µBGA
TQFP
AVDD
AVSS
A1
32
I
Analog positive power supply
J1
8
I
Analog negative power supply (use for ground connection)
BUZZCON
F9
19
O
Buzzer output, a pulse-density modulated signal to apply to external buzzer driver
DVDD
J6
13
I
Digital positive power supply
DVSS
J7
14
I
Digital negative power supply
EAR1ON
A6
27
O
Earphone 1 amplifier output (–)
EAR1OP
A4
29
O
Earphone 1 amplifier output (+)
EAR2O
A2
31
O
Earphone 2 amplifier output
EARVDD
EARVSS
A5
28
I
Analog positive power supply for the earphone amplifiers
A3, A7
30, 26
I
Analog negative power supply for the earphone amplifiers
MBIAS
B1
1
O
Microphone bias supply output, no decoupling capacitors
MCLK
C9
22
I
Master system clock input (2.048 MHz, digital)
MIC1P
C1
2
I
MIC1 input (+)
MIC1N
D1
3
I
MIC1 input (–)
MIC2P
E1
4
I
MIC2 input (+)
MIC2N
F1
5
I
MIC2 input (–)
MUXIN
H1
7
I
Analog MUX input
MUXOUT1
J2
9
I
Analog MUX output
MUXOUT2
J3
10
I
Analog MUX output
PCMI
J8
15
I
Receive PCM input
PCMO
J9
16
O
Transmit PCM output
PCMSYN
G9
18
I
PCM frame sync
PCMCLK
H9
17
I
PCM data clock
PLLVSS
PLLVDD
A9
24
I
PLL negative power supply
A8
25
I
PLL digital power supply
PWRUPSEL
E9
20
I
Selects the power-up default mode
REXT
G1
6
I/O
Internal reference current setting terminal (use precision 100-kΩ resistor and no filtering capacitors)
RESET
D9
21
I
SCL
J5
12
I
Active low reset
I2C-bus serial clock. This input is used to synchronize the data transfer from and to the PCM codec.
SDA
J4
11
I/O
I2C-bus serial address/data input/output. This is a bidirectional terminal used to transfer register
control addresses and data into and out of the codec. It is an open-drain terminal and therefore
requires a pullup resistor to VDD (typical 10 kΩ for 100 kHz).
VSS
B9
23
I
Ground return for bandgap internal reference (use for ground connection)
† All MicroStar Junior BGA pins that are not mentioned have no internal connection.
8
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, AVDD, DVDD, PLLVDD, EARVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V
Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free air temperature range (industrial temperature) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature range, testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 85°C
POWER RATING
TQFP
702 mW
7.2 mW/°C
270 mW
Low dissipation printed
circuit board (PCB)
MicroStar Junior BGA
660 mW
164 mW/°C
220 mW
Low dissipation PCB
MicroStar Junior BGA
2.75 W
36 mW/°C
917 mW
High dissipation PCB
COMMENTS
recommended operating conditions (see Notes 1 and 2)
MIN
Supply voltage, AVDD, DVDD, PLLVDD, EARVDD
NOM
2.7
High-level input voltage, VIH
MAX
UNIT
3.3
V
0.7 x VDD
V
Low-level input voltage, VIL
0.3 x VDD
Load impedance between EAR1OP and EAR1ON-RL
Load impedance for EAR2OP-RL
V
8 to 32
Ω
32
Ω
Operating free-air temperature, TA
– 40
85
C
NOTES: 1. To avoid possible damage and resulting reliability problems to these CMOS devices, follow the power-on initialization paragraph,
described in the Principles of Operation.
2. Voltages are with respect to AVSS, DVSS, PLLVSS , and EARVSS.
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted)
supply current
PARAMETER
IDD
Supply current from VDD
TEST CONDITIONS
TYP
MAX
Operating, EAR1 selected, MicBias disabled
4.5
6
mA
Operating, EAR2 selected, MicBias disabled
4.5
6
mA
2
10
µA
10
30
µA
5
10
ms
Power down room temperature, VDD = 3 V, Reg 6 bit 7 = 1, MClk
not present (see Note 3)
Power down room temperature, VDD = 3 V, , Reg 6 bit 7 = 0,
MClk not present (see Note 3)
ton(i)
Power-up time from
power down
MIN
UNIT
NOTE 3: VIHMIN = VDD, VILMAX = VSS.
www.ti.com
9
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
digital interface
PARAMETER
TEST CONDITIONS
MAX
UNIT
High-level output voltage PCMO (BUZZCON)
IIH
IIL
High-level input current, any digital input
Ci
Input capacitance
Co
Output capacitance
20
pF
RL
Load impedance (BUZZCON)
5
kΩ
Low-level input current, any digital input
VDD = 3 V
VDD = 3 V
TYP
VOH
VOL
Low-level output voltage PCMO
IOH = – 3.2 mA,
IOL = 3.2 mA,
MIN
DVDD– 0.25
V
VI = VDD
VI = VSS
0.25
V
10
µA
10
µA
10
pF
microphone interface
PARAMETER
TEST CONDITIONS
VIO
IIB
Input offset voltage at MIC1N, MIC2N
Ci
Input capacitance at MIC1N, MIC2N
Vn
Microphone input referred noise, psophometrically weighted,
(C-message weighted is similar)
IOmax
V(mbias)
See Note 4
Input bias current at MIC1N, MIC2N
MIN
TYP
–5
– 300
MAX
UNIT
5
mV
300
nA
5
MIC amp 1 gain = 23.5 dB
MIC amp 2 gain = 0 dB
Output source current—MBIAS
3
4.7
µVrms
1.2
mA
2.5
2.65
V
60
100
kΩ
1
Microphone bias supply voltage (see Note 5)
2.3
MICMUTE
pF
– 80
Input impedance
Fully differential
35
dB
NOTES: 4. Measured while MIC1P and MIC1N are connected together. Less than 0.5-mV offset results in 0 value code on PCMOUT.
5. Not a JEDEC symbol.
10
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
speaker interface
PARAMETER
TEST CONDITIONS
TYP
MAX
VDD = 2.7 V, fully differential, 8-Ω load,
3-dBm0 output, volume control = – 3 dB,
RXPGA = – 4 dB level
161
200
VDD = 2.7 V, fully differential, 16-Ω load,
3-dBm0 output, volume control = – 3 dB,
RXPGA = – 2 dB level
128
160
VDD = 2.7 V, fully differential, 32-Ω load,
3-dBm0 output, volume control = – 3 dB,
RXPGA = – 1 dB level
81
100
Earphone AMP2 output power (see Note 6)
VDD = 2.7 V, single-ended, 32-Ω load,
3-dBm0 output
10
12.5
mW
Output offset voltage at EAR1
Fully differential
mV
Earphone AMP1 output power (see Note 6)
VOO
IOmax
Maximum out
output
ut current for EAR1 (rms)
Maximum output current for EAR2 (rms)
MIN
±5
± 30
3-dBm0 input, 8-Ω load
141
178
3-dBm0 input, 16-Ω load
90
112
3-dBm0 input, 32-Ω load
50
63
17.7
22.1
3-dBm0 input
EARMUTE
– 80
UNIT
mW
mA
dB
NOTE 6: Maximum power is with a load impedance of –25%.
transmit gain and dynamic range, companded mode (µ-law or A-law) or linear mode selected, transmit slope
filter bypassed (see Notes 7 and 8)
PARAMETER
Transmit reference-signal level (0 dB)
Overload signal level (3 dBm0)
Overload-signal
Absolute gain error
TEST CONDITIONS
MAX
UNIT
Differential
87.5
mVpp
Differential, normal mode
124
Differential, extended mode
31.5
0-dBm0 input signal, VDD ±10%
MIC1N, MIC1P to PCMO at 3 dBm0 to –30 dBm0
G i error with
ith iinputt llevell relative
l ti tto gain
i att
Gain
–10 dBm0 MIC1N,
MIC1N MIC1P to PCMO
MIN
TYP
–1
1
– 0.5
0.5
MIC1N, MIC1P to PCMO at –31 dBm0 to –45 dBm0
–1
1
MIC1N, MIC1P to PCMO at –46 dBm0 to –55 dBm0
–1.2
1.2
mVpp
dB
dB
NOTES: 7. Unless otherwise noted, the analog input is 0 dB, 1020-Hz sine wave, where 0 dB is defined as the zero-reference point of the channel
under test.
8. The reference signal level, which is input to the transmit channel, is defined as a value 3 dB below the full-scale value of 88-mVrms.
transmit gain and dynamic range, companded mode (µ-law or A-law) or linear mode selected, transmit slope
filter enabled (see Notes 7 and 8)
PARAMETER
Transmit reference-signal level (0 dB)
Overload signal level (3 dBm0)
Overload-signal
Absolute gain error
MAX
UNIT
Differential
TEST CONDITIONS
87.5
mVpp
Differential, normal mode
124
Differential, extended mode
31.5
0-dBm0 input signal, VDD ±10%
MIC1N, MIC1P to PCMO at 3 dBm0 to – 30 dBm0
Gain
G
i error with
ith iinputt llevell relative
l ti tto gain
i att
–10 dBm0 MIC1N,
MIC1N MIC1P to PCMO
MIN
TYP
–1
1
– 0.5
0.5
MIC1N, MIC1P to PCMO at – 31 dBm0 to – 45 dBm0
–1
1
MIC1N, MIC1P to PCMO at – 46 dBm0 to – 55 dBm0
–1.2
1.2
mVpp
dB
dB
NOTES: 7. Unless otherwise noted, the analog input is 0 dB, 1020-Hz sine wave, where 0 dB is defined as the zero-reference point of the
channel under test.
8 The reference signal level, which is input to the transmit channel, is defined as a value 3 dB below the full-scale value of 88-mVrms.
www.ti.com
11
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
transmit filter transfer, companded mode (µ-law or A-law) or linear mode selected, transmit slope filter
bypassed (MCLK = 2.048 MHz)
PARAMETER
Gain
G
i relative
l ti tto iinputt signal
i
l gain
i att 1020 H
Hz, iinternal
t
l hi
high-pass
h
filter disabled
Gain relative to in
input
ut signal gain at 1020 Hz, internal high
high-pass
ass
filter enabled
TEST CONDITIONS
MIN
TYP
MAX
fMIC1 or fMIC2 <100 Hz
fMIC1 or fMIC2 = 200 Hz
– 0.5
0.5
– 0.5
0.5
fMIC1 or fMIC2 = 300 Hz to 3 kHz
fMIC1 or fMIC2 = 3.4 kHz
– 0.5
0.5
– 1.5
0
fMIC1 or fMIC2 = 4 kHz
fMIC1 or fMIC2 = 4.6 kHz
– 14
fMIC1 or fMIC2 = 8 kHz
fMIC1 or fMIC2 < 100 Hz
– 47
fMIC1 or fMIC2 = 200 Hz
–5
UNIT
dB
– 35
– 15
dB
transmit filter transfer, companded mode (µ-law or A-law) or linear mode selected, transmit slope filter
selected, transmit high-pass filter enabled (MCLK = 2.048 MHz) (see Note 9)
PARAMETER
TEST CONDITIONS
MIN
TYP
fMIC1 or f MIC2 =100 Hz
fMIC1 or fMIC2 = 200 Hz
fMIC1 or fMIC2 = 250 Hz
fMIC1 or fMIC2 = 300 Hz
dB
–8
dB
–4
dB
dB
fMIC1 or fMIC2 = 400 Hz
fMIC1 or fMIC2 = 500 Hz
–1.5
dB
–1.3
dB
fMIC1 or fMIC2 = 600 Hz
fMIC1 or fMIC2 = 700 Hz
–1.1
dB
fMIC1 or fMIC2 = 1000 Hz
fMIC1 or fMIC2 = 1500 Hz
– 0.8
dB
– 0.57
dB
– 0.25
dB
0
dB
1.8
dB
fMIC1 or fMIC2 = 2000 Hz
fMIC1 or fMIC2 = 2500 Hz
4.0
dB
6.5
dB
fMIC1 or fMIC2 = 3000 Hz
fMIC1 or fMIC2 = 3100 Hz
7.6
dB
7.7
dB
8
dB
6.48
dB
fMIC1 or fMIC2 = 3300 Hz
fMIC1 or fMIC2 = 3500 Hz
fMIC1 or fMIC2 = 4000 Hz
fMIC1 or fMIC2 = 4500 Hz
–13
dB
–35
dB
fMIC1 or fMIC2 = 5000 Hz
fMIC1 or fMIC2 = 8000 Hz
– 45
dB
– 50
dB
NOTE 9: The pass-band tolerance is ± 0.25 dB from 300 Hz to 3500 Hz.
12
UNIT
– 27
–1.8
fMIC1 or fMIC2 = 800 Hz
fMIC1 or fMIC2 = 900 Hz
Gain relative to in
input
ut signal gain at 1.02 kHz, with slope
slo e filter
selected
MAX
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
transmit idle channel noise and distortion, companded mode (µ-law or A-law) selected, slope filter bypassed
PARAMETER
Transmit idle channel noise, psophometrically
weighted
Transmit signal
signal-to-distortion
to distortion ratio with
1020-Hz sine-wave input
Intermodulation distortion, 2
2-tone
tone CCITT method,
composite power level, –13 dBm0
TEST CONDITIONS
MIN
TXPGA gain= 0 dB, MIC Amp 1 gain = 23.5 dB,
MIC Amp 2 gain = 6 dB
MIC1N, MIC1P to PCMO at 3 dBm0
27
MIC1N, MIC1P to PCMO at 0 dBm0
30
MIC1N, MIC1P to PCMO at – 5 dBm0
33
MIC1N, MIC1P to PCMO at – 10 dBm0
36
MIC1N, MIC1P to PCMO at – 20 dBm0
35
MIC1N, MIC1P to PCMO at – 30 dBm0
26
MIC1N, MIC1P to PCMO at – 40 dBm0
24
MIC1N, MIC1P to PCMO at – 45 dBm0
19
CCITT G.712 (7.1), R2
49
CCITT G.712 (7.2), R2
51
TYP
MAX
– 83.5
– 78
UNIT
dBm0p
dBm0
dB
transmit idle channel noise and distortion, companded mode (µ-law or A-law) selected, slope filter enabled
PARAMETER
Transmit idle channel noise, psophometrically
weighted
Transmit signal
signal-to-total
to total distortion ratio with 1020
1020-Hz
Hz
sine-wave input
Intermodulation distortion, 2
2-tone
tone CCITT method,
composite power level, –13 dBm0
TEST CONDITIONS
MIN
TXPGA gain= 0 dB, MIC Amp 1 gain = 23.5 dB,
MIC Amp 2 gain = 6 dB
MIC1N, MIC1P to PCMO at 3 dBm0
27
MIC1N, MIC1P to PCMO at 0 dBm0
30
MIC1N, MIC1P to PCMO at – 5 dBm0
33
MIC1N, MIC1P to PCMO at –10 dBm0
36
MIC1N, MIC1P to PCMO at –20 dBm0
35
MIC1N, MIC1P to PCMO at – 30 dBm0
26
MIC1N, MIC1P to PCMO at – 40 dBm0
24
MIC1N, MIC1P to PCMO at – 45 dBm0
19
CCITT G.712 (7.1), R2
49
CCITT G.712 (7.2), R2
51
TYP
MAX
– 83.5
– 78
UNIT
dBm0p
dBm0
dB
transmit idle channel noise and distortion, linear mode selected, slope filter bypassed
PARAMETER
Transmit idle channel noise
Transmit signal
signal-to-total
to total distortion ratio with 1020
1020-Hz
Hz
sine-wave input
TEST CONDITIONS
MIN
TXPGA gain = 0 dB, MIC Amp 1 gain = 23.5 dB,
MIC Amp 2 gain = 6 dB
TYP
MAX
– 83.5
– 78
MIC1N, MIC1P to PCMO at 3 dBm0
50
50
MIC1N, MIC1P to PCMO at 0 dBm0
50
65
MIC1N, MIC1P to PCMO at – 5 dBm0
52
61
MIC1N, MIC1P to PCMO at –10 dBm0
56
65
MIC1N, MIC1P to PCMO at –20 dBm0
50
59
MIC1N, MIC1P to PCMO at – 30 dBm0
51
63
MIC1N, MIC1P to PCMO at – 40 dBm0
43
55
MIC1N, MIC1P to PCMO at – 45 dBm0
38
52
www.ti.com
UNIT
dBm0p
dB
13
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
transmit idle channel noise and distortion, linear mode selected, slope filter enabled
PARAMETER
Transmit idle channel noise
Transmit signal
signal-to-total
to total distortion ratio with
1020-Hz sine-wave input
TEST CONDITIONS
MIN
TXPGA gain = 0 dB, MIC Amp 1 gain = 23.5 dB,
MIC Amp 2 gain = 6 dB
TYP
MAX
– 83.5
– 78
MIC1N, MIC1P to PCMO at 3 dBm0
40
50
MIC1N, MIC1P to PCMO at 0 dBm0
50
65
MIC1N, MIC1P to PCMO at – 5 dBm0
50
68
MIC1N, MIC1P to PCMO at –10 dBm0
64
70
MIC1N, MIC1P to PCMO at –20 dBm0
58
65
MIC1N, MIC1P to PCMO at – 30 dBm0
50
60
MIC1N, MIC1P to PCMO at – 40 dBm0
38
50
MIC1N, MIC1P to PCMO at – 45 dBm0
30
45
UNIT
dBm0p
dB
receive gain and dynamic range, EAR1 selected, linear or companded (µ-law or A-law) mode selected (see
Note 10)
PARAMETER
Overload signal level (3 dB)
Absolute gain error
TEST CONDITIONS
TYP
8-Ω load RXPGA = – 4 dB
3.2
16-Ω load RXPGA = – 4 dB
4.05
32-Ω load RXPGA = – 4 dB
4.54
0 dBm0 input signal, VDD ±10%
PCMIN to EAR1ON, EAR1OP at 3 dBm0 to – 40 dBm0
Gain
G
i error with
ith output
t t llevell relative
l ti tto gain
i
at –10 dBm0
MIN
MAX
UNIT
Vpp
–1
1
– 0.5
0.5
PCMIN to EAR1ON, EAR1OP at – 41 dBm0 to – 50 dBm0
–1
1
PCMIN to EAR1ON, EAR1OP at – 51 dBm0 to – 55 dBm0
–1.2
1.2
dB
dB
NOTE 10: RXPGA = – 4 dB for 32 Ω , 16 Ω , or 8 Ω, RXVOL = 0 dB, 1020-Hz input signal at PCMI, output measured differentially between EAR1ON
and EAR1OP
receive gain and dynamic range, EAR2 selected, linear or companded (µ-law or A-law) mode selected (see
Note 11)
PARAMETER
Receive reference signal level (0 dB)
TEST CONDITIONS
MIN
0 dBm0 PCM input signal
14
–1
1
– 0.5
0.5
PCMIN to EAR2O at – 41 dBm0 to – 50 dBm0
–1
1
PCMIN to EAR2O at – 51 dBm0 to – 55 dBm0
– 1.2
1.2
NOTE 11: RXPGA = – 1 dB, RXVOL = 0 dB
www.ti.com
UNIT
Vpp
Vpp
1.925
0 dBm0 input signal, VDD ±10%
PCMIN to EAR2O at 3 dBm0 to – 40 dBm0
Gain
G
i error with
ith output
t t llevell relative
l ti tto gain
i
at –10 dBm0
MAX
1.36
Overload-signal level (3 dB)
Absolute gain error
TYP
dB
dB
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
receive filter transfer, companded mode (µ-law or A-law) or linear mode selected (MCLK = 2.048 MHz) (see
Note 11)
PARAMETER
Gain
G
i relative
l ti tto iinputt signal
i
l gain
i att 1020 H
Hz, iinternal
t
l
high-pass filter disabled
Gain relative to in
input
ut signal gain at 1020 Hz, internal
high-pass filter enabled
TEST CONDITIONS
MIN
TYP
MAX
fEAR1 or fEAR2 < 100 Hz
fEAR1 or fEAR2 = 200 Hz
– 0.5
0.5
– 0.5
0.5
fEAR1 or fEAR2 = 300 Hz to 3 kHz
fEAR1 or fEAR2 = 3.4 kHz
– 0.5
0.5
–1.5
0
fEAR1 or fEAR2 = 4 kHz
fEAR1 or fEAR2 = 4.6 kHz
– 14
fEAR1 or fEAR2 = 8 kHz
fEAR1 or fEAR2 < 100 Hz
– 47
fEAR1 or fEAR2 = 200 Hz
–5
UNIT
dB
– 35
–15
dB
NOTE 11. RXPGA = – 1 dB, RXVOL = 0 dB
receive idle channel noise and distortion, EAR1 selected, companded mode (µ-law or A-law) selected (see
Note 10)
TYP
MAX
Receive noise, psophometrically weighted
PARAMETER
PCMIN = 11010101 (A-law)
– 89
– 86
Receive noise, C-message weighted
PCMIN = 11111111 (µ-law)
36
50
Receive signal
signal-to-distortion
to distortion ratio with 1020
1020-Hz
Hz
sinewave input
TEST CONDITIONS
MIN
PCMIN to EAR1ON, EAR1OP at 3 dBm0
21
PCMIN to EAR1ON, EAR1OP at 0 dBm0
25
PCMIN to EAR1ON, EAR1OP at – 5 dBm0
36
PCMIN to EAR1ON, EAR1OP at –10 dBm0
43
PCMIN to EAR1ON, EAR1OP at – 20 dBm0
40
PCMIN to EAR1ON, EAR1OP at – 30 dBm0
38
PCMIN to EAR1ON, EAR1OP at – 40 dBm0
28
PCMIN to EAR1ON, EAR1OP at – 45 dBm0
23
UNIT
dBm0p
µVrms
dB
NOTE 10: RXPGA = – 4 dB for 32 Ω , RXVOL = 0 dB, 1020-Hz input signal at PCMI, output measured differentially between EAR1ON and EAR1OP.
receive idle channel noise and distortion, EAR1 selected, linear mode selected (see Note 10)
PARAMETER
Receive noise, (20-Hz to 20-kHz brickwall window)
signal-to-distortion
1020-Hz
Receive signal
to distortion ratio with 1020
Hz
sine-wave input
2-tone
Intermodulation distortion, 2
tone CCITT method,
composite power level, –13 dBm0
TEST CONDITIONS
MIN
PCMIN = 000000000000000
TYP
MAX
UNIT
– 88
– 83
dBm0
PCMIN to EAR1ON, EAR1OP at 3 dBm0
53
61
PCMIN to EAR1ON, EAR1OP at 0 dBm0
63
75
PCMIN to EAR1ON, EAR1OP at – 5 dBm0
60
72
PCMIN to EAR1ON, EAR1OP at –10 dBm0
56
67
PCMIN to EAR1ON, EAR1OP at – 20 dBm0
50
63
PCMIN to EAR1ON, EAR1OP at – 30 dBm0
45
50
PCMIN to EAR1ON, EAR1OP at – 40 dBm0
40
51
PCMIN to EAR1ON, EAR1OP at – 45 dBm0
38
49
CCITT G.712 (7.1), R2
50
CCITT G.712 (7.2), R2
54
dB
dB
NOTE 10: RXPGA = – 4 dB for 32 Ω , RXVOL = 0 dB, 1020-Hz input signal at PCMI, output measured differentially between EAR1ON and EAR1OP.
www.ti.com
15
TLV320AIC1110
SLAS359 – DECEMBER 2001
electrical characteristics over recommended ranges of supply voltage and free-air temperature (unless
otherwise noted) (continued)
receive idle channel noise and distortion EAR2 selected, companded mode (µ-law or A-law) selected
(see Note 11)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Receive noise, psophometrically weighted
PCMIN = 11010101 (A-law)
– 82
– 78
Receive noise, C-message weighted
PCMIN = 11111111 (µ-law)
36
50
Receive signal-to-distortion
signal to distortion ratio with 1020-Hz
1020 Hz sinewave input
PCMIN to EAR2O at 3 dBm0
21
PCMIN to EAR2O at 0 dBm0
25
PCMIN to EAR2O at – 5 dBm0
36
PCMIN to EAR2O at –10 dBm0
43
PCMIN to EAR2O at – 20 dBm0
40
PCMIN to EAR2O at – 30 dBm0
38
PCMIN to EAR2O at – 40 dBm0
28
PCMIN to EAR2O at – 45 dBm0
23
UNIT
dBmop
µVrms
dB
NOTE 11. RXPGA = – 1 dB, RXVOL = 0 dB
receive idle channel noise and distortion, EAR2 selected, linear mode selected (see Note 11)
PARAMETER
TEST CONDITIONS
Receive noise, (20-Hz to 20-kHz brickwall window)
MIN
PCMIN = 000000000000000
Receive signal-to-noise + distortion ratio with 1020-Hz sinewave
input
Intermodulation distortion,
distortion 2-tone
2 tone CCITT method
TYP
MAX
UNIT
– 83
– 86
dBm0
PCMIN to EAR2O at 3 dBm0
53
60
PCMIN to EAR2O at 0 dBm0
60
65
PCMIN to EAR2O at – 5 dBm0
58
62
PCMIN to EAR2O at –10 dBm0
55
60
PCMIN to EAR2O at – 20 dBm0
53
60
PCMIN to EAR2O at – 30 dBm0
51
58
PCMIN to EAR2O at – 40 dBm0
50
57
PCMIN to EAR2O at – 45 dBm0
48
52
CCITT G.712 (7.1), R2
50
CCITT G.712 (7.2), R2
54
dB
dB
NOTE 11: RXPGA = – 1 dB, RXVOL = 0 dB
power supply rejection and crosstalk attenuation
PARAMETER
16
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Supply voltage rejection, transmit channel
MIC1N, MIC1P =0 V,
VDD = 3 Vdc + 100 mVpeak to peak, f = 0 to 50 kHz
– 86
– 70
dB
Supply voltage rejection, receive channel,
EAR1 selected (differential)
PCM code = positive zero,
VDD = 3 Vdc + 100 mVpeak to peak, f = 0 to 50 kHz
– 98
– 70
dB
Crosstalk attenuation, transmit-to-receive
(differential)
MIC1N, MIC1P = 0 dB, f = 300 to 3400 Hz measured
differentially between EAR1ON and EAR1OP
70
dB
Crosstalk attenuation, receive-to-transmit
PCMIN = 0 dBm0, f = 300 to 3400 Hz measured at
PCMO, EAR1 amplifier
70
dB
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
timing requirements
clock (2.048-MHz CLK)
PARAMETER
tt
f(mclk)
MIN
NOM
MAX
Transition time, MCLK
10
MCLK frequency
2.048
ns
MHz
MCLK jitter
tc(PCMCLK)
UNIT
37%
Number of PCMCLK clock cycles per PCMSYN frame
256
256
cycles
PCMCLK clock period
156
488
512
ns
Duty cycle, PCMCLK
45%
50%
68%
transmit (2.048-MHz CLK) (see Figure 1)
MIN
MAX
tsu(PCMSYN)
Setup time, PCMSYN high before falling edge of PCMCLK
PARAMETER
20
tc(PCMCLK)– 20
UNIT
th(PCMSYN)
Hold time, PCMSYN high after falling edge of PCMCLK
20
tc(PCMCLK)– 20
ns
receive (2.048-MHz CLK) (see Figure 2)
MIN
MAX
UNIT
tsu(PCSYN)
th(PCSYN)
Setup time, PCMSYN high before falling edge of PCMCLK
PARAMETER
20
ns
Hold time, PCMSYN high after falling edge of PCMCLK
20
tc(PCMCLK)–20
tc(PCMCLK)–20
tsu(PCMI)
th(PCMI)
Setup time, PCMI high or low before falling edge of PCMCLK
20
ns
Hold time, PCMI high or low after falling edge of PCMCLK
20
ns
ns
clock (128-kHz CLK)
PARAMETER
tt
f(mclk)
MIN
NOM
MAX
Transition time, MCLK
10
MCLK frequency
128
5%
Number of PCMCLK clock cycles per PCMSYN frame
PCMCLK clock period
Duty cycle, PCMCLK
tc(PCMSYN)
ns
kHz
MCLK jitter
tc(PCMCLK)
UNIT
16
16
742.19
781.25
820.31
40%
50%
60%
PCMSYN clock period
µs
125
Duty cycle, PCMCLK
49.5%
50%
ns
50.5%
transmit (128-kHz CLK) (see Figure 5)
PARAMETER
MIN
MAX
UNIT
tc(PCMCLK)/4
tc(PCMCLK)/4
ns
tsu(PCMSYN)
th(PCMSYN)
Setup time, PCMSYN high before PCMCLK↑
20
Hold time, PCMSYN high after PCMCLK↓
20
tv(PCMO)
Data valid time after the rising edge of PCMSYNC
50
ns
receive (128-kHz CLK) (see Figure 4)
MIN
MAX
UNIT
tsu(PCSYN)
th(PCSYN)
Setup time, PCMSYN high before rising edge of PCMCLK
PARAMETER
20
ns
Hold time, PCMSYN high after falling edge of PCMCLK
20
tc(PCMCLK)/4
tc(PCMCLK)/4
tsu(PCMI)
th(PCMI)
Setup time, PCMI high or low before falling edge of PCMCLK
20
ns
Hold time, PCMI high or low after falling edge of PCMCLK
20
ns
www.ti.com
ns
17
TLV320AIC1110
SLAS359 – DECEMBER 2001
timing requirements (continued)
I2C bus timing requirements (see Figure 3)
PARAMETER
MIN
MAX
UNIT
400
kHz
SCL
Clock frequency
tw(SCLH)
tw(SCLL)
Pulse duration, SCL high
600
ns
Pulse duration, SCL low
1300
ns
th(STA)
tsu(STA)
Hold time, SCL high after SDA↓ (repeated START condition)†
600
ns
Setup time, for SCL high before SDA↓ repeated START condition
600
ns
th(DAT)
tsu(DAT)
Hold time, SDA valid after SCL low
0
ns
Setup time, SDA valid before SCL↑
100
ns
tsu(STO)
tw(SDAT)
Setup time, STOP condition
600
ns
tr
tf
Rise time (SDA and SCL)
300
ns
Fall time (SDA and SCL)
300
ns
Pulse duration, SDA high (bus free time)
1300
ns
† After this period, the first block pulse is generated.
switching characteristics over recommended ranges of supply voltages and operating free-air
temperature
propagation delay times, CL(max) = 10 pF (see Figure 1)
PARAMETER
tpd1
tpd2
PCMCLK bit 1 high to PCMO bit 1 valid
tpd3
PCMCLK bit n low to PCMO bit n Hi-Z
MIN
PCMCLK high to PCMO valid, bits 2 to n
MAX
UNIT
35
ns
35
ns
30
ns
DTMF generator
PARAMETER
TEST CONDITIONS
DTMF high to low tone relative amplitude (preemphasis)
Tone frequency accuracy (for DTMF)
Resolution of 7.8125 Hz
Harmonic distortion
Measured from lower tone group to
highest parasitic
MIN
TYP
1.5
2
–1.5%
MAX
2.5
UNIT
dB
1.5%
– 20
dB
MICBIAS
PARAMETER
TEST CONDITIONS
Load impedance (bias mode)
18
MIN
TYP
5
www.ti.com
MAX
UNIT
kΩ
TLV320AIC1110
SLAS359 – DECEMBER 2001
PARAMETER MEASUREMENT INFORMATION
Transmit Time Slot
0
1
2
3
4
N–2
N–1
N
N+1
80%
PCMCLK
80%
20%
20%
tsu(PCMSYN)
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
th(PCMSYN)
PCMSYN
1
PCMO
2
tpd3
3
4
N–2
N–1
N
See Note C
tpd1
NOTES: A.
B.
C.
D.
See Note B
tpd2
See Note A
tsu(PCMO)
See Note D
This window is allowed for PCMSYN high.
This window is allowed for PCMSYN low (th(PCMSYN) max determined by data collision considerations).
Transitions are measured at 50%.
Bit 1 = MSB, Bit N = LSB
Figure 1. Transmit Timing Diagram (2.048 MHz)
Receive Time Slot
0
1
2
3
4
N –2
N –1
N
N +1
80%
80%
PCMCLK
20%
20%
ÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎ
tsu(PCMSYN)
PCMSYN
th(PCMSYN)
See Note A
PCMI
1
See Note C
See Note B
See Note D
th(PCMI)
2
3
4
N –2
N –1
N
tsu(PCMI)
NOTES: A.
B.
C.
D.
This window is allowed for PCMSYN high.
This window is allowed for PCMSYN low.
Transitions are measured at 50%.
Bit 1 = MSB, Bit N = LSB
Figure 2. Receive Timing Diagram (2.048 MHz)
SDA
tw(SDAH)
tw(SCLH)
tr
th(STA)
tf
SCL
STO
STA
thd(STA)
th(DAT)
tw(SCLH)
tsu(STA)
tsu(DAT)
tsu(STO)
STA
STO
Figure 3. I2C-Bus Timing Diagram
www.ti.com
19
TLV320AIC1110
SLAS359 – DECEMBER 2001
PARAMETER MEASUREMENT INFORMATION
PCMCLK
th(PCMSYN)
tsu(PCMSYN)
PCMSYNC
th(PCMI)
PCMI
MSB
LSB
tsu(PCMI)
Figure 4. Receive Timing Diagram, 128 kHz
PCMCLK
tsu(PCMSYN)
th(PCMSYN)
PCMSYNC
tv(PCMO)
PCMO
MSB
LSB
Figure 5. Transmit Timing Diagram, 128 kHz
tc(PCMSYNC)
Figure 6. PCMSYNC Timing, 128 kHz
20
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PARAMETER MEASUREMENT INFORMATION
SCL
SDA
A6
A5
A4
A0 R/W
0
ACK
R7
R5
R0 ACK
D7
D6
D5
D0
ACK
0
Slave Address
Start
R6
0
0
Register Address
Stop
Data
NOTE: SLAVE = Voice Codec
Figure 7. I2C-Bus Write to Voice Codec
SCL
SDA
A6
A5
A0 R/W ACK
0
Start
R7
R6
R0 ACK
A6
A0
0
R/W ACK
1
Slave Address
Register Address
D7
D6
D0
0
Slave Address
Slave Drives
The Data
Repeated
Start
NOTE: SLAVE = Voice Codec
ACK
Stop
Master
Drives
ACK and Stop
Figure 8. I2C Read From Voice Codec: Protocol A
SCL
SDA
Start
A6 A5
A0 R/W ACK
0
Slave Address
R7
R6
R0 ACK
0
A6 A5
A0 R/W ACK D7
Stop Start
Register Address
Slave Address
NOTE: SLAVE = Voice Codec
D0 ACK
Slave Drives
The Data
Stop
Master
Drives
ACK and Stop
Figure 9. I2C Read From Voice Codec: Protocol B
www.ti.com
21
TLV320AIC1110
SLAS359 – DECEMBER 2001
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
(Detector OFF)
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
(Detector ON)
45
30
40
I DD – Supply Current – µ A
I DD – Supply Current – µ A
25
20
VDD = 3.3 V
15
10
VDD = 3.0 V
35
30
25
VDD = 3.3 V
20
15
10
VDD = 3.0 V
5
5
0
–50
VDD = 2.7 V
VDD = 2.7 V
0
50
TA – Free-Air Temperature – °C
0
–50
100
RELATIVE GAIN
vs
FREQUENCY
5
Both Filters
Disabled
Relative Gain – dB
Relative Gain – dB
–20
High-Pass
Filter Selected
and Slope Filter
Disabled
–60
–5
–10
High-Pass
Filter and
Slope Filter
Selected
1k
f – Frequency – Hz
High-Pass
Filter Selected
and Slope Filter
Disabled
–15
–20
–100
100
Both Filters
Disabled
0
0
–80
High-Pass
Filter and
Slope Filter
Selected
–25
10k
–30
100
1k
f – Frequency – Hz
Figure 10. Transmit Gain Response With Respect to Gain of 1-kHz Tone
22
100
RELATIVE GAIN
vs
FREQUENCY
20
–40
0
50
TA – Free-Air Temperature – °C
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
TYPICAL CHARACTERISTICS
RELATIVE GAIN RESPONSE
vs
FREQUENCY
5
0
Relative Gain – dB
–5
–10
–15
–20
–25
–30
–35
10
100
1k
10k
f – Frequency – Hz
Figure 11. Receive Gain Response With Respect to Gain of 1-kHz Tone
With High-Pass Filter Selected and High-Pass Filter Disabled
www.ti.com
23
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
power-on initialization
An external reset with a minimum pulse width of 500 ns must be applied to the active low RESET terminal to
assure reset upon power on. All registers are set with default values upon external reset initialization.
The desired selection for all programmable functions can be initialized prior to a power-up command using the
control interface.
Table 1. Power-Up and Power-Down Procedures (VDD = 2.7 V, earphone amplifier unloaded)
DEVICE STATUS
Power up
Power down
PROCEDURE
MAXIMUM POWER
CONSUMPTION
Set bit 1 = 1 in power control register, EAR1 enabled
16.2 mW
Set bit 1 = 0 in power control register, EAR2 enabled
14.6 mW
Set bit 7 = 1 in TXPGA control register and bit 0 = 0
1.35 µW
Set bit 7 = 0 in TXPGA control register and bit 0 = 0
67.5 µW
In addition to resetting the power down bit in the power control register, loss of MCLK (no transition detected)
automatically enters the device into a power-down state with PCMO in the high impedance state. If during a
pulse code modulation (PCM) data transmit cycle an asynchronous power down occurs, the PCM interface
remains powered up until the PCM data is completely transferred.
An additional power-down mode overrides the MCLK detection function. This allows the device to enter the
power down state without regard to MCLK. Setting bit 7 of the TXPGA sidetone register to logic high enables
this function.
internal reference current setting terminal
Use a 100-kΩ precision resistor to connect the REXT pin to GND.
conversion laws
The device can be programmed for either a 15-bit linear or and 8-bit (µ-law or A-law) companding mode. The
companding operation approximates the CCITT G.711 recommendation. The linear mode operation uses a
15-bit twos-complement format.
transmit operation
microphone input
The microphone input stage is a low-noise differential amplifier that provides a preamplifier gain of 23.5 dB. It
is recommended that a microphone capacitively connected to the MIC1N and MIC1P inputs, while the MIC2N
and MIC2P inputs can be used to capacitively connect a second microphone or an auxiliary audio circuit.
24
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
transmit operation (continued)
_
MBIAS
+
Rmic
Vref
510 kΩ
Ci MIC1N
34 kΩ
_
M
I
C
+
34 kΩ
Ci MIC1P
Rmic
510 kΩ
Figure 12. Typical Microphone Interface
microphone mute function
Transmit channel muting provides 80-dB attenuation of the input microphone signal. The MICMUTE function
can be selected by setting bit 6 of the power control register through the I2C interface.
transmit channel gain control
The values in the transmit PGA control registers control the gain in the transmit path. The total TX channel gain
can vary from 41.5 dB to 19.5 dB. The default total TX channel gain is 23.5 dB.
Table 2. Transmit Gain Control
BIT NAME
MIC AMP1
MIC AMP2
TX PGA
GAIN
GAIN
MODE
TOTAL TX GAIN
TP3
TP2
TP1
TP0
GAIN
GAIN
MIN
TYP
MAX
UNIT
0
0
0
0
23.5
18
0
Extended
41.3
41.5
41.7
dB
0
0
0
1
23.5
18
–2
Extended
39.3
39.5
39.7
dB
0
0
1
0
23.5
18
–4
Extended
37.3
37.5
37.7
dB
0
0
1
1
23.5
18
–6
Extended
35.3
35.5
35.7
dB
0
1
0
0
23.5
18
–8
Extended
33.3
33.5
33.7
dB
0
1
0
1
23.5
18
–10
Extended
31.3
31.5
31.7
dB
1
0
0
0
23.5
6
0
Normal
29.3
29.5
29.7
dB
1
0
0
1
23.5
6
–2
Normal
27.3
27.5
27.7
dB
1
0
1
0
23.5
6
–4
Normal
25.3
25.5
25.7
dB
1
0
1
1
23.5
6
–6
Normal
23.3
23.5
23.7
dB
1
1
0
0
23.5
6
–8
Normal
21.3
21.5
21.7
dB
1
1
0
1
23.5
6
–10
Normal
19.3
19.5
19.7
dB
www.ti.com
25
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
receive operation
receive channel gain control
The values in the receive PGA control registers control the gain in the receive path. PGA gain is set from
– 6 dB to 6 dB in 1-dB steps through the I2C interface. The default receive channel gain is – 4 dB.
Table 3. Receive PGA Gain Control
BIT NAME
RELATIVE GAIN, VOICE MODE
RP3
RP2
RP1
RP0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
1
0
1
0
MIN
DTMF GAIN
GAIN, TONE NODE
TYP
MAX
UNIT
5.8
6
6.2
dB
12
4.8
5
5.2
dB
12
0
3.8
4
4.2
dB
12
1
2.8
3
3.2
dB
6
0
0
1.8
2
2.2
dB
6
0
1
0.8
1
1.2
dB
6
1
1
0
– 0.2
0
0.2
dB
0
0
1
1
1
–1.2
–1
– 0.8
dB
0
1
0
0
0
– 2.2
–2
–1.8
dB
0
1
0
0
1
– 3.2
–3
– 2.8
dB
–6
1
0
1
0
– 4.2
–4
– 3.8
dB
–6
1
0
1
1
– 5.2
–5
– 4.8
dB
–6
1
1
0
0
– 6.2
–6
– 5.8
dB
–12
1
1
0
1
X
dB
–12
1
1
1
0
X
dB
–12
sidetone gain control
The values in the sidetone PGA control registers control the sidetone gain. Sidetone gain is set from –12 dB
to – 24 dB in 2-dB steps through the I2C interface. Sidetone can be muted by setting bit 7 of the power control
register. The default sidetone gain is –12 dB.
Table 4. Sidetone Gain Control
BIT NAME
26
RELATIVE GAIN
ST2
ST1
ST0
MIN
TYP
MAX
UNIT
0
0
0
–12.2
–12
–11.8
dB
0
0
1
–14.2
–14
–13.8
dB
0
1
0
–16.2
–16
–15.8
dB
0
1
1
–18.2
–18
–17.8
dB
1
0
0
– 20.2
– 20
–19.8
dB
1
0
1
– 22.2
– 22
– 21.8
dB
1
1
0
– 24.2
– 24
– 23.8
dB
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
receive operation (continued)
receive volume control
The values in the volume control PGA control registers provide volume control for the earphone. Volume control
gain is set from 0 dB to –18 dB in 2-dB steps through the I2C interface. The default RX volume control gain
is 0 dB.
Table 5. RX Volume Control
BIT NAME
RELATIVE GAIN
RV3
RV2
RV1
RV0
MIN
TYP
MAX
0
0
0
0
– 0.2
0
0.2
UNIT
dB
0
0
0
1
– 2.2
–2
–1.8
dB
0
0
1
0
– 4.2
–4
– 3.8
dB
0
0
1
1
– 6.2
–6
– 5.8
dB
0
1
0
0
– 8.2
–8
–7.8
dB
0
1
0
1
–10.2
–10
– 9.8
dB
0
1
1
0
–12.2
–12
–11.8
dB
0
1
1
1
–14.2
–14
–13.8
dB
1
0
0
0
–16.2
–16
–15.8
dB
1
0
0
1
–18.2
–18
–17.8
dB
earphone amplifier
The analog signal can be routed to either of two earphone amplifiers: one with a differential output (EAR1ON
and EAR1OP) capable of driving a 8-Ω load, or one with a single-ended output (EAR2O) capable of driving a
8-Ω load.
earphone mute function
Muting can be selected by setting bit 3 of the power control register through the I2C interface.
receive PCM data format
Companded mode: 8 bits are received, the most significant (MSB) first.
Linear mode: 15 bits are received, MSB first.
www.ti.com
27
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
receive operation (continued)
Table 6. Receive-Data Bit Definitions
BIT NO.
COMPANDED
MODE
LINEAR
MODE
1
CD7
LD14
2
CD6
LD13
3
CD5
LD12
4
CD4
LD11
5
CD3
LD10
6
CD2
LD9
7
CD1
LD8
8
CD0
LD7
9
–
LD6
10
–
LD5
11
–
LD4
12
–
LD3
13
–
LD2
14
–
LD1
15
–
LD0
16
–
––
Transmit channel gain control bits always follow the PCM data in time:
CD7-CD0 = data word in companded mode
LD14-LD0 = data word in linear mode
DTMF generator operation and interface
The DTMF circuit generates the summed DTMF tones for push button dialing and provides the PDM output for
the BUZZCON user-alert tone. The integer value is determined by the formula round tone [Freq (Hz)/resolution
(Hz)]. The integer value is loaded into one of two 8-bit registers, high-tone register (04) or low-tone register (05).
The tone output is 2 dB higher when applied to the high-tone register (04). When generating DTMF tones, the
high-frequency value must be applied to the high tone register (04) and the low DTMF value to the low-tone
register.
The DTMF frequency resolution is controlled by the auxiliary register (06) bits 2, 3, 4, and 5. When the resolution
is set to 7.8125 Hz, the frequency range can be up to 1992.2 Hz. A wider range can be accomplished (for
example, 2x or 4x) by selecting lower resolutions of 15.625 Hz or 31.250 Hz. The gain setting is controlled by
the RXPGA gain control. This register applies the required gain to obtain MUX control during tone mode
operation. Table 3 shows the relationship of the two gain settings.
28
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
DTMF generator operation and interface (continued)
Table 7. Typical DTMF and Single Tone Control
DT7
DT6
DT5
DT4
DT3
DT2
DT1
DT0
INTEGER
VALUE
TONE
FUNCTION
TONE/HZ
0
1
0
1
1
0
0
1
89
DTMF Low
697
0
1
1
0
0
0
1
1
99
DTMF Low
770
0
1
1
0
1
1
0
1
109
DTMF Low
852
0
1
1
1
1
0
0
0
120
DTMF Low
941
1
0
0
1
1
0
1
1
155
DTMF HIgh
1209
1
0
1
0
1
0
1
1
171
DTMF HIgh
1336
1
0
1
1
1
1
0
1
189
DTMF HIgh
1477
1
1
0
1
0
0
0
1
209
DTMF HIgh
1633
Tones from the DTMF generator block are present at all outputs and are controlled by enabling or disabling the
individual output ports. The values that determine the tone frequency are loaded into the tone registers (high
and low) as two separate values.
The values loaded into the tone registers initiate an iterative table look-up function, placing a 6-bit or 7-bit in
twos-complement value into the the tone registers. There is a 2-dB difference in the resulting output of the two
registers, the high-tone register having the greater result.
In the case of low-tone signal, the tone generator outputs a 6-bit integer with a maximum code of 31 (011111).
However, the DTMF output is an 8-bit integer. Therefore, two zeros are padded to the MSB position, which
results in 31 (00011111). On the other hand, the receive channel requires a 15-bit integer, the input 3968
(000111110000000). Since the maximum digital value of receive channel is 16383 (011111111111111), the
maximum low-tone signal is designed to be – 12.32 dB below the full digital scale.
20 log
3968 Ǔ
ǒ16383
2
(1)
+ –12.32 dB
In the case of high-tone signal, the tone generator outputs a 7-bit integer with a maximum code of 39 (0100111).
The DTMF, therefore, pads a zero to the MSB and generates an 8-bit integer (00100111). In order to send the
digital code to receive channel, it is converted to a 15-bit integer with seven more zeros padded to LSB position
and biased as 4992 (001001110000000). Therefore, the maximum high-tone signal is designed to be – 10.32 dB
below the full digital scale.
20 log
4992 Ǔ
ǒ16383
2
(2)
+ –10.32 dB
In the case of DTMF output, the tone generator outputs an 8-bit integer with the maximum code level of 70
(01000110). This output is converted to a 15-bit code with the value of 8960 (010001100000000). Therefore,
the maximum output of DTMF is designed to be – 5.24 dB below the full digital scale.
20 log
8960 Ǔ
ǒ16383
2
(3)
+ –5.24 dB
www.ti.com
29
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
buzzer logic section
The single-ended output BUZZCON is a PDM signal intended to drive a buzzer through an external driver
transistor. The PDM begins as a selected DTMF tone, generated and passed through the receive D/A channel
and fed back to the transmit channel analog modulator, where a PDM signal is generated and routed to the
BUZZCON output.
DTMF
Gain
Mux
DTMF
Digital
Modulator
and
Filter
Analog
Modulator
Buzzer
Control
Buzzcon
Figure 13. Buzzer Driver System Architecture
support section
The clock generator and control circuit use the master clock input (MCLK) to generate internal clocks to drive
internal counters, filters, and convertors. Register control data is written into and read back from the PCM codec
registers via the control interface.
I2C- bus protocols
The PCM codec serial interface is designed to be I2C bus-compatible and operates in the slave mode when CE
is high. This interface consists of the following terminals:
SCL:
I2C-bus serial clock. This input synchronizes the control data transfer to and from the codec.
SDA:
I2C-bus serial address/data input/output. This is a bidirectional terminal that transfers register
control addresses and data into and out of the codec. It is an open drain terminal and therefore
requires a pullup resistor to VCC (typical 10 kΩ for 100 kHz).
TLV320AIC1110 has a fixed device select address of (E2)HEX for write mode and (E3)HEX for read mode.
For normal data transfer, SDA is allowed to change only when SCL is low. Changes when SCL is high are
reserved for indicating the start and stop conditions.
Data transfer may be initiated only when the bus is not busy. During data transfer, the data line must remain
stable whenever the clock line is at high. Changes in the data line while the clock line is at high are interpreted
as a start or stop condition.
Table 8. I2C-Bus Conditions
CONDITION
STATUS
DESCRIPTION
A
Bus not busy
Both data and clock lines remain at high.
B
Start data transfer
A high to low transition of the SDA line while the clock (SCL) is high determines a start condition.
All commands must proceed from a start condition.
C
Stop data transfer
A low to high transition of the SDA line while the clock (SCL) is high determines a stop condition.
All operations must end with a stop condition.
D
Data valid
The state of the data line represents valid data when, after a start condition, the data line is stable
for the duration of the high period of the clock signal.
The data on the line must be changed during the low period of the clock signal. There is one clock pulse per
bit of data.
30
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
I2C- bus protocols (continued)
Each data transfer is initiated with a start condition and terminated with a stop condition. The number of data
bytes, transferred between the start and stop conditions, is determined by the master device (microprocessor).
When addressed, the PCM codec generates an acknowledge after the reception of each byte. The master
device must generate an extra clock pulse that is associated with this acknowledge bit.
The PCM codec must pull down the SDA line during the acknowledge clock pulse so that the SDA line is at stable
low state during the high period of the acknowledge related clock pulse. Setup and hold times must be taken
into account. During read operations, the master device must signal an end of data to the slave by not generating
an acknowledge bit on the last byte that was clocked out of the slave. In this case, the slave (PCM codec) must
leave the data line high to enable the master device to generate the stop condition.
clock frequencies and sample rates
A fixed PCMSYN rate of 8 kHz determines the sampling rate.
register map addressing
BITS
REG
07
06
05
04
03
02
01
00
PWRUP
TXSLOPE En
Power control
00
Sidetone En
TXEn
RX TX En
MICSEL
BIASEn
RXEn
EAROUT
Sel
Mode control
01
Comp Sel
TMEn
PCMLB
Comp En
BUZZEn
RXFLTR En
TXFLTR
En
TXPGA
02
X
TP3
TP2
TP1
TP0
ST2
ST1
ST0
RXPGA
03
RP3
RP2
RP1
RP0
RV3
RV2
RV1
RV0
High DTMF
04
HIFREQ
Sel7
HIFREQ
Sel6
HIFREQ
Sel5
HIFREQ
Sel4
HIFREQ
Sel3
HIFREQ
Sel2
HIFREQ
Sel1
HIFREQ Sel0
Low DTMF
05
LOFREQ
Sel7
LOFREQ
Sel6
LOFREQ
Sel5
LOFREQ
Sel4
LOFREQ
Sel3
LOFREQ
Sel2
LOFREQ
Sel1
LOFREQ
Sel0
AUX
06
MCLK
Detect
RXPGA2†
DTMFH1
DTMFH0
DTML1
DTMFL0
AMVX
MCLK sel
† For voice mode only
register power-up defaults
BITS
REG
03
02
01
00
Power control (1)†
Power control (2)‡
00
1
1
1
1
0
1
1
0
00
1
0
0
1
1
0
1
1
Mode control
01
0
0
0
0
0
0
1
0
TXPGA
02
0
1
0
0
0
0
0
0
RXPGA
03
1
0
1
0
0
0
0
0
High DTMF
04
0
0
0
0
0
0
0
0
Low DTMF
05
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
AUX
06
† 1. Value when PWRUPSEL = 0
‡ 2. Value when PWRUPSEL = 1
07
06
05
04
www.ti.com
31
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
register map
Table 9. Power Control Register: Address (00) HEX
BIT NUMBER
5
4
3
2
1
DEFINITIONS
7
6
0
1
1
1
1
0
1
1
0
Default setting PWRUPSEL = 0
1
0
0
1
1
0
1
1
Default setting PWRUPSEL = 1
X
X
X
X
X
X
X
0
Reference system, power down
X
X
X
X
X
X
X
1
Reference system, power up
X
X
X
X
X
X
1
X
EAR AMP1 selected, EAR AMP2 power down
X
X
X
X
X
X
0
X
EAR AMP2 selected, EAR AMP1 power down
X
X
X
X
X
0
X
X
Receive channel enabled
X
X
0
X
X
1
X
X
Receive channel muted
X
X
1
X
X
1
X
0
Receive channel, power down
X
X
X
X
1
X
X
X
Micbias enable
X
X
X
X
0
X
X
X
Micbias disable
X
X
X
1
X
X
X
X
MIC1 selected
X
X
X
0
X
X
X
X
MIC2 selected
X
0
X
X
X
X
X
X
Transmit channel enabled
X
1
0
X
X
X
X
X
Transmit channel muted
X
1
1
X
X
X
X
X
Transmit channel power down
0
X
X
X
X
X
X
X
Sidetone enabled
1
X
X
X
X
X
X
X
Sidetone muted
Table 10. Mode Control Register: Address (01) HEX
BIT NUMBER
7
32
6
5
4
3
2
1
0
DEFINITIONS
0
0
0
0
0
0
1
0
Default setting
X
X
X
X
X
X
0
0
TX channel high-pass filter enabled and slope filter enabled
X
X
X
X
X
X
0
1
TX channel high-pass filter enabled and slope filter disabled
X
X
X
X
X
X
1
0
TX channel high-pass filter disabled and slope filter enabled
X
X
X
X
X
X
1
1
TX channel high-pass filter disabled and slope filter disabled
X
X
X
X
X
0
X
X
RX channel high-pass filter disabled (low pass only)
X
X
X
X
X
1
X
X
RX channel high-pass filter enabled
X
X
X
X
0
X
X
X
BUZZCON disabled
X
X
X
X
1
X
X
X
BUZZCON enabled
X
X
X
0
X
X
X
X
Linear mode selected
1
X
X
1
X
X
X
X
A-law companding mode selected
0
X
X
1
X
X
X
X
µ-law companding mode selected
X
X
0
X
X
X
X
X
TX and RX channels normal mode
X
X
1
X
X
X
X
X
PCM loopback mode
X
0
X
X
X
X
X
X
Tone mode disabled
X
1
X
X
X
X
X
X
Tone mode enabled
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
register map (continued)
Transmit PGA and sidetone control register: Address (02)HEX
Bit definitions:
7
6
5
4
3
2
1
0
DEFINITION
X
TP3
TP2
TP1
TP0
ST2
ST1
ST0
See Table 2 and Table 4
0
1
0
0
0
0
0
0
Default setting
Receive volume control register: Address (03)HEX
Bit definitions:
7
6
5
4
3
2
1
0
DEFINITION
RP3
RP2
RP1
RP0
RV3
RV2
RV1
RV0
See Table 3 and Table 5
1
0
1
0
0
0
0
0
Default setting
High tone selection control register: Address (04)HEX
Bit definitions:
7
6
5
4
3
2
1
0
DEFINITION
X
X
X
X
X
X
X
X
DTMF (see Table 7)
0
0
0
0
0
0
0
0
Default setting
Low tone selection control register: Address (05)HEX
Bit definitions :
7
6
5
4
3
2
1
0
DEFINITION
X
X
X
X
X
X
X
X
DTMF (see Table 7)
0
0
0
0
0
0
0
0
Default setting
Auxiliary register: Address (06)HEX
Bit definitions:
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
Default
DEFINITION
X
X
X
X
X
X
X
0
MCLK is set to 2.048 MHz
X
X
X
X
X
X
X
1
MCLK is set to 128 MHz
X
X
X
X
X
X
0
X
Analog switch output is set to OUT2
X
X
X
X
X
X
1
X
Analog switch output is set to OUT1
X
X
X
X
0
0
X
X
Low tone frequency resolution is set to 7.8125 Hz
X
X
X
X
0
1
X
X
Low tone frequency resolution is set to 15.625 Hz
X
X
X
X
1
0
X
X
Low tone frequency resolution is set to 31.250 Hz
X
X
0
0
X
X
X
X
High tone frequency resolution is set to 7.8125 Hz
X
X
0
1
X
X
X
X
High tone frequency resolution is set to 15.625 Hz
X
X
1
0
X
X
X
X
High tone frequency resolution is set to 31.250 Hz
X
0
X
X
X
X
X
X
Receiver channel gain, RXPGA2 is equal to 0 dB, voice mode only
X
1
X
X
X
X
X
X
Receiver channel gain, RXPGA2 is equal to 6 dB, voice mode only
0
X
X
X
X
X
X
X
MCLK detector is powered ON
1
X
X
X
X
X
X
X
MCLK detector is powered OFF
www.ti.com
33
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
using PCM codec as a general-purpose PCM codec
In situations when a general-purpose PCM codec is needed and programming features are not necessary, the
receive and transmit channels can be enabled for voice mode only by setting the powerup select pin to VCC level.
When set to default, the following features are activated:
REF is powered up
Ear amp1 selected, Ear amp 2 = OFF
Receive channel enabled
MIC bias enabled
MIC 2 selected
Transmit channel enabled
Side tone enabled, Gain = – 12 dB
TX channel high pass filter disabled
TX channel slope filter enabled
RX channel HP filter disabled (low pass only)
Buzzcon disabled
Linear mode only
TX and RX channel normal mode (no loopback)
Tone mode disabled (voice mode only)
MIC amp 1 gain
MIC amp 2 gain
TX PGA gain
Total TX gain
Receive PGA
Receive PGA 2
Volume
Total RX gain
=
=
=
=
23.5 dB
6 dB
0 dB
29.5 dB
=
=
=
=
– 4 dB
0 dB
0 dB
– 4 dB
Clock = 2.048 MHz
34
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
PRINCIPLES OF OPERATION
PCM codec device comparisons
TLV320AIC1103
TLV320AIC1110
Single tone frequency range
To 2 kHz
To 8 kHz
Transmit channel gain range
13.5 dB to 35.5 dB
19.5 dB to 41.5 dB
Receive channel gain range
– 24 dB to 6 dB
– 24 dB to 12 dB
PCMCLK rate
2.048 MHz
Device pin out
Control registers
Number of registers
Control interface
Analog switch
128 kHz or 2.048 MHz
Backward compatible (TQFP)
Backward compatible
6
I2C
7
I2C
No
Yes
Earout driving impedance
32 Ω
8-32 Ω
DTMF
Yes
Yes
Tone resolution (Hz)
7.8125
7.8125
15.625
31.25
Packages
TQFP
TQFP,
MicroStar Junior BGA
www.ti.com
35
TLV320AIC1110
SLAS359 – DECEMBER 2001
MECHANICAL DATA
PBS (S-PQFP-G32)
PLASTIC QUAD FLATPACK
0,23
0,17
0,50
24
0,08 M
17
25
16
32
9
0,13 NOM
1
8
3,50 TYP
Gage Plane
5,05
SQ
4,95
0,25
7,10
SQ
6,90
0,10 MIN
0°–ā7°
0,70
0,40
1,05
0,95
Seating Plane
0,08
1,20 MAX
4087735/A 11/95
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
36
www.ti.com
TLV320AIC1110
SLAS359 – DECEMBER 2001
MECHANICAL DATA
GQE (S-PBGA-N80)
PLASTIC BALL GRID ARRAY
5,20
SQ
4,80
4,00 TYP
0,50
J
0,50
H
G
F
E
D
C
B
A
1
0,68
0,62
2
3
4
5
6
7
8
9
1,00 MAX
Seating Plane
0,35
0,25
∅ 0,05 M
0,21
0,11
0,08
4200461/B 04/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. MicroStar Junior BGA configuration
MicroStar Junior BGA is a trademark of Texas Instruments.
www.ti.com
37
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLV320AIC1110GQER
ACTIVE
VFBGA
GQE
80
2500
TLV320AIC1110PBS
ACTIVE
TQFP
PBS
32
250
TLV320AIC1110PBSR
ACTIVE
TQFP
PBS
32
1000
Lead/Ball Finish
MSL Peak Temp (3)
TBD
SNPB
Level-2A-235C-4 WKS
TBD
CU NIPDAU
Level-2-235C-1 YEAR
TBD
CU NIPDAU
Level-2-235C-1 YEAR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated