AFE1302 AF E 130 2 www.ti.com ADSL ANALOG FRONT-END ● ● ● ● FEATURES ● NOISE FLOOR: –144dBm/Hz ● MULTIRATE COMPATIBLE 8.8M TO 1.1MWords/s WORD RATE FIVE GENERAL-PURPOSE OUTPUTS 570mW POWER DISSIPATION TQFP-48 PACKAGE ● VCXO CIRCUITRY AND DAC DESCRIPTION Burr-Brown’s Analog Front-End from Texas Instruments reduces the size and cost of an ADSL-compliant system by providing the active analog circuitry needed to connect an ADSL Digital Signal Processor (DSP) to an external line driver, receiver, TX/RX filters, hybrid, transformer, and POTS filter. The AFE1302 is designed for downstream data rates of 4Mbps and higher, and operation at a clock rate of 35.328MHz, with an output word rate of up to 8.832MWords/s. Functionally, this unit consists of a transmit (TX) channel, a receive (RX) channel, a VCXO (Voltage Controlled Crystal Oscillator) control Digital-to-Analog Converter (DAC), and VCXO active circuitry. The TX section converts, filters, and buffers outgoing Discrete Multi Tone (DMT) data from the ADSL DSP. The receive section amplifies, filters, and digitizes the DMT data received on the twisted pair line. This IC operates on a single 5V supply. The digital circuitry in the unit can be connected to a supply voltage ranging from 3.3V to 5V. The chip uses only 570mW. The AFE1302 is designed to be used with external amplifiers and filters for noise reduction and dynamicrange improvement. The RX channel consists of a low-noise PGA, a switched capacitor low-pass filter, and fourth-order delta-sigma Analog-to-Digital Converter (ADC). The delta-sigma modulator operating at a 32X oversampling ratio produces a 16-bit output at word rates up to 8832kHz. The TX channel consists of a fourth-order delta-sigma DAC, switched-capacitor low-pass filter, programmable attenuator, and buffer. The buffer drives offchip into a low-noise line driver configured as a 3-pole active filter to produce an overall low-noise high-drive TX output signal on a twisted pair line. Patents Pending AFE1302 Interpolation Filter 16-Bit DAC LP Filter 16-Bit ADC LP Filter Atten Buffer TX Output Digital Loopback Decimation Filter From DSP Digital Interface Copyright © 2000, Texas Instruments Incorporated PGA VCXO Active Ckts VCXO DAC SBWS014 Analog Loop Back General Purpose Digital Output RX Input 5 Printed in U.S.A. December, 2000 SPECIFICATIONS Typical at 25°C, AVDD = +5V, DVDD = +3.3V, fCLK = 35.328MHz, TX output and RX input measured differentially, unless otherwise specified. AFE1302Y PARAMETER RECEIVE CHANNEL Input Signal (CMV = AVDD/2) Common-Mode Voltage Input Impedance Input Capacitance Programmable Amplifier Range Gain Step Size Input Noise Output Word Rate Output Word Resolution ADC Sampling Rate Low-Pass Frequency Corner Passband Droop SINAD THD MTPR (MultiTone Power Ratio) TRANSMIT CHANNEL Input Word Rate Input Word Resolution Peak Signal Amplitude Common-Mode Voltage Load Resistance Load Capacitance Programmable Attenuator Range Attenuator Step Size Attenuator Step Accuracy Low-Pass Filter Corner Frequency Passband Ripple Group Delay Variation Output Noise TYP Differential, G = –6dB 9.0 9.6 AVDD/2 2.8 30 –6 Monotonicity Guaranteed PGA = +40dB(1) MAX 40 1 –148 1.104 (15 Bits + 1 Sign Bit) or (14 Bits + 2 Sign Bits) –144 8.832 16 35.328 One Pole Analog Filter At 550kHz PGA Gain = 40dB, Input Referred PGA Gain = 0dB Single Tone, PGA = 0dB 1.1 1 100 68 75 84 75 1.104 (15 Bits + 1 Sign Bit) or (14 Bits + 2 Sign Bits) Differential, G = 0dB 4.4 Differential Differential 8.832 16 4.8 AVDD/2 400 10 VCXO WITH EXTERNAL CIRCUITRY Frequency Tuning Range DAC Resolution DIGITAL INTERFACE Logic Levels VIH VIL VOH VOL CONTROL INTERFACE (GC0, GC1, GP0, GP1, GP2) Logic Levels VOH VOL MWords/s Bits Vp-p 35.328 ±100 10 MHz ppm Bits 10 Measured at 50kHz Measured at 200kHz FS Output 0dB FS Output –6dB See Note (2) Vp-p V kΩ pF dB dB dBm/Hz MWords/s Bits MSamples/s MHz dB dB dB dB dB –110 –116 65 73 –98 70 0 1.0 0.5 127 –0.1 Fourth-Order, 0.1dB Programmable UNITS Ω pF dB dB dB kHz dB µs dBm/Hz dBm/Hz dBc dBc dBVrms dB –31 Monotonicity Guaranteed SFDR in RX Band (20 Tone Test) MTPR TEMPERATURE RANGE Operation Thermal Resistance, θJA MIN Pin-to-AVDD THD Distortion POWER Analog Power Supply Voltage Analog Dissipated Power Digital Power Supply Voltage Digital Dissipated Power CONDITIONS Sensitive to PCB Layout Monotonicity Guaranteed |IIH| < 10µA |IIL| < 10µA IOH = –20µA IOL = 20µA DVDD – 1 –0.3 DVDD – 0.5 IOH = 1mA IOL = 1mA DVDD – 0.5 AVDD 4.75 DVDD VDD = 3.3V 3.0 DVDD 0 5 470 3.3 100 0 DVDD + 0.3 0.8 0.4 V V V V 0.4 V V 5.25 5.5 70 56.5 V mW V mW °C °C/W NOTES: (1) With TX in operation, no RX data, referred to 100Ω. (2) With TX reverb multitone signal (25.875kHz to 138kHz at a 4.3125kHz step), measured signal level beyond 150kHz at TXP, TXN. 2 AFE1302 SBWS014 PIN CONFIGURATION CLKNIB DVSS2 AVSS1 XTALO XTALI AVDD1 VCXO VREF2 AVDD2 AVSS2 AVSS5 TQFP CLKM Top View 48 47 46 45 44 43 42 41 40 39 38 37 CLWD 1 36 AVSS4 CTRLIN 2 35 TXP DVDD1 3 34 AVDD4 DVSS1 4 33 TXN TX3 5 32 AVSS6 TX2 6 TX1 7 30 CMO TX0 8 29 VREF1 RX3 9 28 VRNTX RX2 10 27 VRPTX RX1 11 26 VRNRX RX0 12 25 VRPRX 31 CMI 16 17 18 19 20 21 PDOWN RESETN GP2 GP1 GP0 RXN RXP AVDD3 ABSOLUTE MAXIMUM RATINGS 22 23 24 GC0 15 GC1 14 AVSS3 13 CLIP AFE1302 ELECTROSTATIC DISCHARGE SENSITIVITY Analog Inputs: Current ............................................. ±100mA, Momentary ±10mA, Continuous Voltage ................................. AGND –0.3V to AVDD +0.3V Analog Outputs Short Circuit to Ground (+25°C) ................... Continuous AVDD to AGND ....................................................................... –0.3V to 6V DVDD to DGND ....................................................................... –0.3V to 6V Digital Input Voltage to DGND ................................ –0.3V to DVDD +0.3V Digital Output Voltage to DGND ............................. –0.3V to DVDD +0.3V AGND, DGND, Differential Voltage .................................................... 0.3V Junction Temperature (TJ) ............................................................ +150°C Storage Temperature Range ......................................... –40°C to +125°C Lead Temperature (soldering, 3s) ................................................. +260°C Power Dissipation .......................................................................... 700mW This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER AFE1302Y TQFP-48 355 0°C to +70°C AFE1302Y AFE1302Y/250 Tape and Reel " " " " AFE1302Y/2K Tape and Reel " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces of “AFE1302Y/2K” will get a single 2000-piece Tape and Reel. AFE1302 SBWS014 3 PIN DESCRIPTIONS Number Type Pin Name Description External Connection GC0 GC1 RXN RXP VRPRX VRNRX CMO VRPTX VRNTX VREF1 CMI TXP TXN VREF2 VCXO XTALI XTALO External Gain Control Output LSB External Gain Control Output MSB Analog Receive Negative Input Analog Receive Positive Input RX Reference Positive Output RX Reference Negative Output Output Common-Mode voltage TX Reference Positive Output TX Reference Negative Output Unbuffered Bandgap Reference Unbuffered Common-Mode Voltage TX Positive Output TX Negative Output DAC Reference Voltage VXCO Control Voltage DAC Output XTAL Oscillator Input XTAL Oscillator Output Optional Swap Amp Optional Swap Amp Line Interface Line Interface 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 0.1uF,1µF to AVSS3 Line Interface Line Interface XTAL Interface XTAL Interface XTAL XTAL CLKM CLKNIB CLWD CTRLIN TX3 TX2 TX1 TX0 RX3 RX2 RX1 RX0 CLIP PDOWN RESETN GP2 GP1 GP0 Master Clock Output, f = 35.328MHz Nibble Clock Output Word Clock Output Serial Data Input Digital Transmit Input Digital Transmit Input Digital Transmit Input Digital Transmit Input Digital Receive Output Digital Receive Output Digital Receive Output Digital Receive Output Clipping Detection Output Power-Down Select, “1” = Power Down Reset Pin (Active LOW) General-Purpose Output 2 General-Purpose Output 1 General-Purpose Output 0 DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP DSP — — — Digital Ground 2 Digital Power Digital Ground 1 Analog Power (Main) Analog Ground (Main) Analog Ground for TX Output Analog Power for TX Output Analog Ground for TX Output Analog Clock Ground Analog Clock Ground Analog Clock Power XTAL Power XTAL Ground DGND Plane 0.1uF,1µF to DVSS1 DGND Plane 0.1uF,1µF to AVSS3 AGND Plane AGND Plane 0.1uF,1µF to AVSS4 AGND Plane AGND Plane AGND Plane 0.1uF,1µF to AVSS2 0.1uF,1µF to AVSS1 AGND Plane Analog Interface 23 24 19 20 25 26 30 27 28 29 31 35 33 40 41 43 44 Output Output Input Input Output Output Output Output Output Output Output Output Output Output Output — — Digital Interface 48 47 1 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Output Output Output Input Input Input Input Input Output Output Output Output Output Input Input Output Output Output Supply voltages 46 3 4 21 22 32 34 36 37 38 39 42 45 4 — 3V or 5V — 5V — — 5V — — — 5V 5V — DVSS2 DVDD1 DVSS1 AVDD3 AVSS3 AVSS6 AVDD4 AVSS4 AVSS5 AVSS2 AVDD2 AVDD1 AVSS1 AFE1302 SBWS014 THEORY OF OPERATION The AFE1302 consists of a transmit (TX) channel, a receive (RX) channel, and a digital interface to connect to an ADSL DSP. In addition, VCXO circuitry and a VCXO control DAC are included for precise clock generation. The TX channel receives digital data at the nominal rate of 1.104MWords/s to 8.832MWords/s. These TX data words are interpolated up to the AFE1302 clock rate of 35.328MHz. The data is converted to analog form with a 16-bit deltasigma DAC and bandwidth limited with a fourth-order, switched-capacitor low-pass filter. The filter output is buffered and drives off-chip to an external Burr-Brown linedriver circuit from Texas Instruments. This line driver is configured as an LC passive filter to provide additional outof-band noise and distortion attenuation (see System section). Transmit power can be reduced with a combination of digital and analog attenuation to ensure compliance with the G.992.2 “politeness” rule. In the RX channel, the analog receive signal is input to a PGA. The output of the first-order, switched capacitor filter is digitized with a 16-bit delta-sigma ADC. A decimation filter ensures a compliant word rate (1.104MWords/s to 8.832MWords/s) to the ADSL digital chip. Precise phase alignment is required to ensure proper operation of the ADSL modem. The active circuitry required to create a VCXO is included on the AFE1302. This includes the gain element as well as a 10-bit, monotonic DAC. The only external components required are a varactor, load capacitor, and crystal. TX DISTORTION AND NOISE REQUIREMENTS The TX output is a DMT signal generated by the AFE1302. This output contains the desired DMT signal in the TX frequency band as well as unwanted noise and distortion in both the TX and RX frequency bands. The inband TX distortion and noise is specified by the MultiTone Power Ratio (MTPR) test. Since MTPR is better than 70 dB, fullrate ADSL performance is guaranteed for TX upstream signals. However, TX distortion and noise can also limit downstream RX performance. TX noise and distortion can degrade RX signal quality since the TX output is connected to the RX input through filters, line driver, and hybrid. Three tests show out-of-band TX performance as used in the ADSL system. Total harmonic distortion (THD) shows the overall linearity of the TX signals. The next test uses a typical ADSL DMT TX signal and measures the largest distortion tone in the RX band. The largest distortion tone in the RX band is –98 dBVrms or –124 dBm/Hz as measured in a 4.3125 kHz bandwidth. In the last test, TX noise is measured by transmitting no signal. Noise as shaped by the TX filter is lower than –116dBm/Hz in the RX band. AFE1302 SBWS014 To insure that TX distortion and noise do not degrade the RX downstream performance, external filtering and transhybrid loss of greater than 30dB is required. Refer to Figure 6 for an external circuit and contract TI for a detailed reference design document. DIGITAL DATA TRANSMISSION Data is transmitted to the AFE1302 from the DSP on the TX[0:3] lines, as shown in Figure 1. The Data TX[0:3] changes during the rising edge of CLKM within the DSP, and the Data are valid on the falling edge of CLKM for the AFE to read. The minimum setup and hold time are 5ns (see Figure 2); the start of a new sample is indicated by CLWD being HIGH. ADSL DSP TX[0:3] 4 RX[0:3] 4 AFE1302 CTRLIN Control Register CLWD ÷4N CLKNIB ÷N CLKM NOTE: N = 1, 2, 4, 8 set by control register. FIGURE 1. AFE1302/DSP Interface. Data is transmitted to the DSP from the AFE1302 on the RX[0:3] lines, as shown in Figure 1. The Data RX[0:3] changes during the rising edge of CLKM within the AFE, and the Data are valid on the falling edge of CLKM for the DSP to read. The minimum setup and hold time are 5ns (see Figure 2); the start of a new sample is indicated by CLWD being HIGH. During normal operation, a 16-bit TX data word is generated by the DSP. This TX data is sent from the DSP to the AFE via four serial lines TX[0:3]. Each serial line is clocked by CLKM at 35.328MHz or by CLKNIB at 35.328MHz divided by N. CLKNIB and CLWD can be changed by programming N via the control register. The RX word output rate and TX word input rate can be changed by programming N in the control register for values of 1, 2, 4, or 8. For instance, setting N = 1 sets the TX and RX data word rate to 8.832Mwords/s. 5 CLKM/CLKNIB CLWD tS tH RX[0:3]/TX[0:3] N0 N1 N2 N3 NOTE: CLKM = 35.328; For N = 1, CLKNIB = 35.328MHz, CLWD = 8.832MHz; tS: Setup Time, min tS = 5ns; tH: Hold Time, min tH = 5ns. FIGURE 2. AFE1302 Transmit/Receive Timing Diagram. TRANSMIT DATA RECEIVE DATA Transmit data TX[0:3] passed to the AFE1302 will be Binary Two’s Complement with one or two sign bits depending on bit 9 in the AFE1302 control register at address 001 (see Table V). Bit 9 = 0 is two sign bits and bit 9 = 1 is one sign bit. Please refer to Tables I and II. Data RX[0:3] received from the AFE1302 will be in the format shown in Tables III and IV: BIT MAP\NIBBLE TX0 TX1 TX2 TX3 N0 data bit data data data N1 0 (LSB) bit 1 bit 2 bit 3 data data data data bit bit bit bit N2 4 5 6 7 N3 data bit 8 data bit 12 data bit 9 data bit 13 data bit 10 data sign data bit 11 data sign BIT MAP\NIBBLE RX0 RX1 RX2 RX3 N0 data bit data data data N1 0 (LSB) bit 1 bit 2 bit 3 data data data data bit bit bit bit N2 4 5 6 7 N3 data bit 8 data bit 12 data bit 9 data bit 13 data bit 10 data sign data bit 11 data sign TABLE III. AFE1302 RX Data Format, Address 001, Bit 9 = 0. TABLE I. AFE1302 TX Data Format, Address 001, Bit 9 = 0. This corresponds to the internal data structure as follows (sign bit is repeated): INTERNAL DATA BIT EXTERNAL DATA BIT 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 This corresponds to the internal data structure as follows (sign bit is repeated): INTERNAL DATA BIT Sign Sign 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EXTERNAL DATA BIT TX0 TX1 TX2 TX3 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Sign Sign 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BIT MAP\NIBBLE BIT MAP\NIBBLE 15 N0 data bit data data data N1 0 (LSB) bit 1 bit 2 bit 3 data data data data bit bit bit bit N2 4 5 6 7 N3 data bit 8 data bit 12 data bit 9 data bit 13 data bit 10 data bit 14 data bit 11 data sign RX0 RX1 RX2 RX3 N0 data bit data data data N1 0 (LSB) bit 1 bit 2 bit 3 data data data data bit bit bit bit N2 4 5 6 7 N3 data bit 8 data bit 12 data bit 9 data bit 13 data bit 10 data bit 14 data bit 11 data sign TABLE IV. AFE1302 RX Data Format, Address 001, Bit 9 = 1. TABLE II. AFE1302 TX Data Format, Address 001, Bit 9 = 1. This corresponds to the internal data structure as follows: This corresponds to the internal data structure as follows: INTERNAL DATA BIT INTERNAL DATA BIT EXTERNAL DATA BIT 6 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EXTERNAL DATA BIT Sign 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Sign 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 AFE1302 SBWS014 CLIP EVENT PROGRAMMING THE AFE1302 Receive data (AFEG_RX) is generated in the AFE1302 with additional headroom. For the one sign-bit case, if AFEG_RX data is greater than 7FFF, it will be clipped to 7FFF. If AFEG_RX data is less than 8000, it will be clipped to 8000. For the two sign-bit case, if AFEG_RX data is greater than 3FFF, it will be clipped to 3FFF. If AFEG_RX data is less than C000, it will be clipped to C000. During clip, pin CLIP will be asserted HIGH for monitoring purposes. Pin CLIP will remain HIGH until 0 is written to address = 010, bit 3 in AFE1302 control register. The internal AFE control register, as shown in Table V, is used to set the programmable features of the AFE1302 and to set the VCXO frequency. Serial data is sent from the DSP to the AFE control register on the CTRLIN pin in 16-bit blocks. This data is clocked into the AFE1302 on the falling edge of CLWD. AFEREG data is valid when followed by at least 16 stop bits (HIGH). The timing is shown in Figure 3. During programming, all AFE1302 functions are active. Data ID code 0 through 5 must be configured for normal operation; data ID code 6 and 7 are reserved for future use. CLWD CTRLIN Start Bit 12 Data Bits Data ID 3 Bit ≥ 16 HIGH Stop Bits CLWD tS tH CTRLIN NOTE: CLWD = 8.832MHz/N; tS: Setup Time, min tS = 10ns; tH: Hold Time, min tH = 10ns. FIGURE 3. AFE1302 Program Timing. AFE1302 SBWS014 7 START BIT DATA ID DATA BITS M S B L S B 15 14 13 12 11 0 0 0 0 0 0 0 0 9 0 0 X 1 0 0 X 0 0 0 X 1 5 4 0 0 X 1 2 1 0 RX REGISTER 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 External Gain Control GC1 (1 Bit) External Gain Control GC0 (1 Bit) AGC RX Gain Setting –6dB (6 Bits) AGC RX Gain Setting –5dB (6 Bits) AGC RX Gain Setting X dB (6 Bits) AGC RX Gain Setting 40dB (6 Bits) X = 1, Filter Setting 1.1MWords/s; X = 0, Filter Setting 8.8MWords/s Reserved, Must Be Set As Shown 0 0 X 1 0 0 X 1 0 0 X 1 2 1 0 TX REGISTER 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 Transmit Attenuator Setting = 0dB (5 Bits) Transmit Attenuator Setting = –1dB (5 Bits) Transmit Attenuator Setting = X dB (5 Bits) Transmit Attenuator Setting = –31dB (5 Bits) GP2 (General-Purpose Output 2) GP1 (General-Purpose Output 1) GP0 (General-Purpose Output 0) X = 1, RX and TX Data Format Has 1 Sign Bit and 15 Data Bits X = 0, RX and TX Data Format Has 2 Sign Bits and 14 Data Bits Reserved, Must Be Set As Shown 2 1 0 AFE REGISTER 0 1 0 0 1 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Digital Loopback TX to RX Through Digital Section (1 Bit) X = 1, Loopback Mode; X = 0, Normal Operation Mode Analog Loopback TX to RX Through Analog Section (1 Bit) X = 1, Loopback Mode; X = 0, Normal Operation Mode X = 1, RX Enable Mode Data Word Clock Divider (2 Bits) Data Word Clock = 8.832MHz (2 Bits) Data Word Clock = 4.416MHz (2 Bits) Data Word Clock = 2.208MHz (2 Bits) Data Word Clock = 1.104MHz (2 Bits) Clear CLIP Signal: X = 1, RX is Clipping; X = 0, CLIP Cleared Reserved, Must Be Set As Shown 3 2 1 0 VCXO DAC VALUE REGISTER 0 0 0 0 0 0 1 1 1 1 1 1 1 1 VCXO DAC Input Word (10 Bits) VCXO DAC Input Word = 0 (10 Bits) VCXO DAC Input Word = +FS (10 Bits) Reserved, Must Be Set As Shown 4 3 2 1 0 INTERFACE REGISTER 1 1 0 0 0 0 1 0 0 1 0 0 0 1 0 0 Reserved X = 0, TX[3:0] Should Be Latched On Falling CLKNIB X = 1, TX[3:0] Should Be Latched On Rising CLKNIB X = 0, RX[3:0] Should Be Latched On Falling CLKNIB X = 1, RX[3:0] Should Be Latched On Rising CLKNIB Digital Loopback RX Into TX: X = 1 Loopback Mode; X = 0 Normal Mode Reserved, Must Be Set As Shown 0 1 X 0 0 0 X 1 0 0 X 1 10 9 8 7 0 0 0 6 5 4 3 0 1 X 1 X X X 10 9 0 0 1 8 7 6 5 4 3 X X 0 0 0 0 0 0 0 0 X X 0 0 1 1 X 0 1 0 1 X 15 14 13 12 11 X 0 1 X 0 1 X 0 1 X 0 1 15 14 13 12 11 X X X X 0 0 1 0 0 1 10 9 X 0 1 X 0 1 8 7 6 5 4 X 0 1 X 0 1 X 0 1 X 0 1 10 9 8 7 X X X X 6 5 X 0 X 0 X 0 15 14 13 12 11 0 0 0 3 X 0 0 0 6 X 15 14 13 12 11 0 0 0 0 7 X 0 0 8 X 15 14 13 12 11 0 0 0 0 0 0 0 0 10 1 X X 1 X X 1 X X 1 X X REGISTER DESCRIPTIONS 10 9 8 7 6 5 4 3 2 1 0 RESERVED 1 X X 0 X X 1 X X 1 X X 1 X X 1 X X 1 X X 1 X X 1 1 1 0 1 1 1 0 1 Reserved, Must Be Set As Shown Reserved, Data ID 6 Reserved, Data ID 7 NOTE: All registers are initially set to zero. TABLE V. AFE1302 Control Register. 8 AFE1302 SBWS014 DIGITAL-TO-ANALOG CONVERTER LAYOUT The Digital-to-Analog Converter (DAC) data for the TX channel is deserialized and written in four 4-bit registers and coded in two’s complement, as shown in Table VI. The analog front-end of an ADSL system has a number of conflicting requirements. It must accept and deliver digital outputs at fairly high rates of speed, and convert the line input to a high precision (14-bit) digital output. Thus, there are two sections of the AFE1302: the digital section, and the analog section. The recommended VCXO circuit layout is shown in Figure 4. DAC/ADC HEXDATA 1 SIGN BIT Positive Full-Scale Mid-Scale Negative Full-Scale 7FFF 0000 8000 DIGITAL LAYOUT TABLE VI. One Sign Bit. The power supply for the digital section of the AFE1302 can range from 3.3V to 5V. This supply should be decoupled to digital ground with a ceramic 0.1µF capacitor placed as close as possible to digital ground (DVSS) and digital power (DVDD). Ideally, both a digital power-supply plane and a digital ground plane should run to and underneath the digital pins of the AFE1302. However, DVDD may be supplied by a wide printed circuit board trace. A digital ground plane underneath all digital pins is strongly recommended. ANALOG-TO-DIGITAL CONVERTER The Analog-to-Digital Converter (ADC) data from the RX channel is stored in four 4-bit registers and coded in two’s complement, as shown in Table VII. DAC/ADC HEXDATA 2 SIGN BITS ANALOG I/O Positive Full-Scale Mid-Scale Negative Full-Scale 3FFF 0000 C000 ANALOG LAYOUT The remaining portion of the AFE1302 should be considered analog. Note that AVDD must be in the 4.75V to 5.25V range. All AVSS pins should be connected directly to a common analog ground plane and all AVDD pins should be connected to an analog 5V power plane. Both of these planes should have a low impedance path to the power supply. The analog power-supply pins should be decoupled to analog ground with both a 10µF tantalum capacitor and a 0.1µF ceramic capacitor. The ceramic capacitors should be placed as close to the AFE1302 as possible. The placement of the tantalum capacitor is not as critical, but should be close to the pin. In each case, the capacitor should be connected between AVDD and AVSS. TABLE VII. Two Sign Bits. SCALABLE TIMING The AFE1302 scales operation with the clock frequency. All internal filters change frequency with the clock speed so that the unit can be used at different frequencies just by changing the clock speed. For the RX channel, the digital filtering of the delta-sigma converter scales directly with the clock speed. For the TX channel, the power spectral density scales directly with the clock rate. The transformer and external filter need to be changed for different frequency requirements. 68.1kΩ Ground Plane Sensitive Points 68.1kΩ No Ground/Power Planes Or Other Traces In This Area XTAL ANALOG I/O To AFE1302 Pin #41 FIGURE 4. VCXO Circuit Layout, Approximately Two Times Actual Size. AFE1302 SBWS014 9 proper system operation. An on-chip fourth-order low-pass transmit filter has been included on the AFE1302 to reduce transmit noise in the receive bandwidth. However, external filtering, as shown in the reference design in Figure 6, is required on the transmitter output to optimize the receive path noise mask. The reference design circuit not only implements extra filtering for the transmit noise, but also includes the drivers necessary to achieve the G.992.2 specified +13dBm output power on the line, thus achieving a minimum component solution. SYSTEM This analog front-end will give the best performance only when included in an optimized system. This section describes external components that will work best with the AFE1302. See Figure 5 for the basic connection diagram. TRANSMIT The key noise specification for an ADSL analog front-end is the noise that is added to the RX channel. It is essential to reduce the transmit noise that reaches the receiver for VREF1 VRNRX VRPRX VRNTX VRPTX CMO CMI ADSL DSP TX[0:3] TXP TXN GP0 GP1 RX[0:3] CTRLIN AFE1302 CLWD GC0 GC1 RXP RXN CLKNIB CLKM DVDD1 AFE External Circuit Telephone Line AVDD1, 2, 3, and 4 3.3V to 5V Digital 5V Analog FIGURE 5. Basic Connection Diagram. AFE1302 CPE 0.8:1 UTP Line CO HP POTS Filter Hybrid LC Passive TX Filter/Line Driver TX DSP High-Pass/ AA Filter Computer G Receive Amp RX G FIGURE 6. CPE Block Diagram (contact factory for detatiled reference design). 10 AFE1302 SBWS014 The specifications for the complete system solution are given in Table VIII. The numbers include the effects of both the AFE1302 and the surrounding external components, including a Burr-Brown TX line driver from Texas Instruments. RECEIVE Receive channel external components include a hybrid, receive amplifier, fifth-order high-pass passive filter, and first-order, low-pass, anti-alias filter. The ADSL system is frequency division multiplexed on a single twisted pair. Filters are used to separate the transmit and receive signals. When the AFE1302 drives long twisted-pair loops, the transmit signal is much larger than the receive signal. The hybrid will ideally eliminate all of the transmit signal at the receive input. However, for poorly matched lines, the actual reduction may be quite small. Without external filtering between the transmit output and the receive input, the transmit signal will clip the receive input before the on-chip receive filter can reduce the transmit signal. Therefore, external receive filters are required to eliminate transmit noise. Refer to Figure 6 for an external circuit and contact the factory for a detailed reference design document. ADSL FRONT-END SYSTEM PERFORMANCE PARAMETER TX PATH Peak Signal Amplitude to Telephone Line Load Impedance Output Power Low-Pass Filter Corner Frequency Passband Ripple Group Delay Variation Output Noise, Out of Band RX PATH RX Input MTPR Noise Floor External High-Pass Filter Corner Frequency Anti-Alias Filter Corner Frequency Passband Ripple CONDITIONS To Line (100Ω Match) See Note (2) PGA = 40dB VALUE UNITS 12 100 13 127 3 15 –142 Vp-p Ω dBm kHz dB ms dBm/Hz 12.5 70 –142 157 1.1 3 Vp-p dB dBm/Hz kHz MHz dB NOTE: (1) dBm referenced from average tone power and spread over 4kHz receive tone bins. (2) Measured at 200kHz with typical ADSL multitone transmission signal. TABLE VIII. ADSL Front-End System Performance when using the AFE1302 in a Texas Instruments Reference Design Evaluation Board. Typical at 25°C, AVDD = +5V, DVDD = +3.3V, fCLK = 35.328MHz, TX output and RX input measured at line side. AFE1302 SBWS014 11 PACKAGE OPTION ADDENDUM www.ti.com 3-Oct-2003 PACKAGING INFORMATION ORDERABLE DEVICE STATUS(1) PACKAGE TYPE PACKAGE DRAWING PINS PACKAGE QTY AFE1302Y/250 ACTIVE TQFP PFB 48 250 AFE1302Y/2K ACTIVE TQFP PFB 48 2000 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated