POWER SOLUTION - NIKKOHM 50W to 500W HIGH POWER WIRE WOUND RESISTORS FLAT SHAPED ALUMINUM HOUSED IRN50-IRN150 IRF150-IRF500 Features and Applications Non-inductive, flat shaped aluminum housed wire wound fixed resistors with 50W to 500W.. Minimum resistance of 1ohm, +/-0.5% tolerance available. 10mm thickness allows excellent heat extrusion from resistor. Narrower body (IRN) will be suitable for high density installation. Light weight silicone filled insulation and higher temperature operating cement filled insulation are prepared. Strong over load characteristics are fit for applications of industrial power electronics, switching power supplies, braking resistors for motor control electronics, rush current protection in automotive electronics, industrial power supplies. Dimensions (mm) D B G 300+/-10 Type IRN 50 IRN100 IRN150 IRF100 IRF150 IRF200 IRF250 IRF300 IRF400 IRF500 A 70+/-1 120+/-1 170+/-1 90+/-1 120+/-1 150+/-1 180+/-1 210+/-1 270+/-1 330+/-1 B 60+/-0.3 60+/-0.3 60+/-0.3 80+/-0.3 80+/-0.3 80+/-0.3 80+/-0.3 80+/-0.3 80+/-0.3 80+/-0.3 F C 10 10 10 10 10 10 10 10 10 10 D 50+/-0.3 50+/-0.3 50+/-0.3 70+/-0.3 70+/-0.3 70+/-0.3 70+/-0.3 70+/-0.3 70+/-0.3 70+/-0.3 E A F E 50+/-0.3 100+/-0.3 150+/-0.3 70+/-0.3 100+/-0.3 130+/-0.3 160+/-0.3 190+/-0.3 250+/-0.3 310+/-0.3 C F 95 125 155 G dia. 4-5.3 dia. 4-5.3 dia. 4-5.3 dia. 4-5.3 dia. 4-5.3 dia. 4-5.3 dia. 4-5.3 dia. 6-5.3 dia. 6-5.3 dia. 6-5.3 dia. Weight(g) 100 160 220 155 200 245 290 335 430 525 POWER SOLUTION - NIKKOHM 50W to 500W HIGH POWER WIRE WOUND RESISTORS FLAT SHAPED ALUMINUM HOUSED. IRN50-IRN150, IRF150-IRF500 Ordering Information P/N Type IRN100S1R0J 0.75sqmm IRN150C1K0F IRF200S100RJ IRF500C10RJ 2sqmm IRN100 IRN150 IRF200 IRF500 Specifications Type IRN 50 IRN100 IRN150 IRF100 IRF150 IRF200 IRF250 IRF300 IRF400 IRF500 Rating power with heat sink 50W 100W 150W 100W 150W 200W 250W 300W 400W 500W Insulating Material S(Silicone) C(Cement) S(Silicone) C(Cement) Resistance (ohm) 1-420 1-1.1K 1-1.75K 1-1.1K 1-1.75K 1-2.2K 1-2.79K 1-3.5K 1-4.45K 1-5.78K Resistance Tolerance Additional 1 ohm 1K ohm 100 ohm 10 ohm +/-5%(J) +/-1%(F) +/-0.5%(D) +/-5%(J) Lead wire Tolerance (%) Dielectric strength +/-0.5(D) +/-1.0(F) +/-2.0(G) +/-5.0(J) +/-10(K) Standard AC1000V, Available AC 1500V 2500V 3000V 4500V at 2mA current Lead wire Lead wire 2mm2 1.25 mm2 NA 1-420 NA 1-1.1K NA 1-1.75K NA 1-1.1K NA 1-1.75K 1-4 ohm 4.1 1-5 ohm 5.1 1-6 ohm 6.1 1-8 ohm 8.1 1-10 ohm 10.1 - Performance Term Temperature Coefficient Insulation Resistance Operating Temperature, cement filled Operating Temperature, silicone filled Specifications +/-260 ppm/C 20Megohm min. -55C - +200C -55C - +150C Short Time Overload +/-(1.0%+0.05ohm) Moisture Resistance +/-(2.0%+0.05ohm) Thermal Shock +/-(1.0%+0.05ohm) Vibration +/-(1.0%+0.05ohm) Humidity +/-(2.0%+0.05ohm) Load Life +/-(2.0%+0.05ohm) Note for derating, cement filled type. (1) Attached on chassis for 150W to 500W and free air for 50W-100W. (2) Free air for 150W. (3) Free air for 200W and 250W. (4) Free air for 300W to 500W. Note for lead wire: 0.75 sqmm leads is available. Conditions Maximum Dry condition. 5 times rating power, 5 seconds. 40C, 95%RH, DC100V case to leads, 500H Heating with rating power 30 minutes, –25C 15 minutes 10-50-10Hz, 1 minute/cycle, 2 hours, x , y and z direction. 40C, 95%RH, 0.1 rating power, 90min ON, 30min OFF, 500hours. Rating power, 90min ON, 30min OFF, 500hours. Derating %Rating Watts 100 (1) 25C 80 (2) 60 (3) 40 (4) 0 -50 20030114 280C 20 0 50 100 150 200 250 300 Ambient Temperature (C)