TI TNETE2201PJD

TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
D
D
D
D
D
1.25 Gigabits Per Second (Gbps) Gigabit
Ethernet Transceiver
Based On the P802.3Z Specification
Transmits Serial Data Up to 1.25 Gbps
Operates With 3.3-V Supply Voltage
5-V Tolerant on TTL Inputs
D
D
D
D
D
Interfaces to Electrical Cables/Backplane or
with Optical Modules
PECL Voltage Differential Signaling Load,
1 V Typ with 50 Ω – 75 Ω
Receiver Differential Input Voltage
200 mV Minimum
Low Power Consumption
64-Pin Quad Flat Pack With Thermally
Enhanced Package
description
The TNETE2201 Gigabit Ethernet transceiver provides for ultra high-speed bidirectional point-to-point data
transmission. This device is based on the timing requirements of the proposed 10-bit interface specification by
the P802.3z Gigabit Task Force.
1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
33
16
1718 19 20 21 22 23 24 25 26 27 28 29 30 31 32
RC0
SYNC
GND_TTL
RD0
RD1
RD2
VCC_TTL
RD3
RD4
RD5
RD6
VCC_TTL
RD7
RD8
RD9
GND_TTL
TC0
VCC _TX
LOOPEN
VCC _A
GND_A
REFCLK
VCC _CMOS
SYNCEN
GND_CMOS
RESERVED
LCKREFN
VCC _A
VCC _A
RBC1
RBC0
GND_A
GND_CMOS
TD0
TD1
TD2
VCC_CMOS
TD3
TD4
TD5
TD6
VCC_CMOS
TD7
TD8
TD9
GND_CMOS
GND_TX
TC1
VCC _RX
RC1
GND_A
VCC _A
DOUT_TXP
DOUT_TXN
VCC _A
VCC _A
GND_CMOS
VCC _A
GND_A
VCC _A
DIN_RXP
VCC _A
DIN_RXN
GND_RX
PHD OR PJD PACKAGE
(TOP VIEW)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
description (continued)
The intended application of this device is to provide building blocks for developing point-to-point baseband data
transmission over controlled-impedance media of approximately 50 Ω to 75 Ω. The transmission media can be
printed-circuit board traces, back planes, cables, or fiber-optical media. The ultimate rate and distance of data
transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the
environment.
The TNETE2201 performs the data serialization and deserialization (SERDES) functions for the gigabit
ethernet physical layer interface. The transceiver operates at 1.25 Gbps (typical), providing up to 1000 Mbps
of bandwidth over a copper or optical media interface. The serializer/transmitter accepts 8b/10b parallel
encoded data bytes. The parallel data bytes are serialized and transmitted differentially nonreturn-to-zero
(NRZ) at pseudo-ECL (PECL) voltage levels. The deserializer/receiver extracts clock information from the input
serial stream and deserializes the data, outputting a parallel 10-bit data byte. The 10-bit data bytes are output
with respect to two receive byte clocks (RBC0, RBC1) allowing a protocol device to clock the parallel bytes in
RBC clock rising edges.
The transceiver automatically locks onto incoming data without the need to prelock. However, the transceiver
can be commanded to lock to the externally supplied reference clock (REFCLK) as a reset function, if needed.
The TNETE2201 provides an internal loopback capability for self-test purposes. Serial data from the serializer
is passed directly to the deserializer allowing the protocol device a functional self-check of the physical interface.
The TNETE2201 is characterized for operation from 0°C to 70°C.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
functional block diagram
LOOPEN
TX+
TX–
TD0 – TD9
10
/
10-Bit
Register
10
/
Clock
Multiplier
REFCLK
125 MHz
SYNCEN
Synchronous
Detect
SYNC
RD0 – RD9
Shift
Register
10
/
10-Bit
Register
10
/
Shift
Register
62.5 MHz
RBC0
÷2
RBC1
125 MHz
PLL Clock
Recovery and
Data Retiming
62.5 MHz
2:1
MUX
RX+
RX–
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
I/O structures
PECL inputs (DIN_RXP, DIN_RXN)
PECL outputs (DIN_TXP, DIN_TXN)
VDD
VDD
100 Ω
DIN_RXP
DOUT_TXP
4 kΩ
VCM
VDD
+
_
VDD
4 kΩ
DIN_RXN
DOUT_TXN
CMOS inputs (TD0 – TD9, LOOPEN, REFCLK, SYNCEN, LCKREFN)
VDD
VDD
TERMINALS
P
R1
120 Ω
Input
Open Circuit Open Circuit
LOOPEN
Open Circuit
400 kΩ
400 kΩ
Open Circuit
N
CMOS outputs (RD0 – RD9, RBC0, RBC1, SYNC)
VDD
P
Output
N
4
POST OFFICE BOX 655303
R2
REFCLK, TD0 – TD9
SYNCEN, LCKREFN
R2
R1
• DALLAS, TEXAS 75265
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
Terminal Functions
TERMINAL
DESCRIPTION
NAME
NO.
TYPE
DOUT_TXP
DOUT_TXN
62
61
Output
Differential output transmit. DOUT_TXP and DOUT_TXN are differential serial outputs that interface
to a copper or an optical I/F module. These terminals transmit NRZ data at a rate of 1.25 Gbps.
DOUT_TXP and DOUT_TXN are held static when LOOPEN is high and are active when LOOPEN is
low .
DIN_RXP
DIN_RXN
54
52
Input
Differential input receive. DIN_RXP and DIN_RXN together are the differential serial input interface
from a copper or an optical I/F module. These terminals receive NRZ data at a rate of 1.25 Gbps and
are active when LOOPEN is held low.
LCKREFN
27
Input
Lock to reference. When LCKREFN is asserted low, the receive PLL phase locks to the supplied
REFCLK signal. LCKREFN prelocks or resets the receive PLL.
LOOPEN
19
Input
Loop enable. When LOOPEN is high (active), the internal loop-back path is activated. The
transmitted serial data is directly routed to the inputs of the receiver. This provides a self-test
capability in conjunction with the protocol device. The DOUT_TXP and DOUT_TXN outputs are held
static during the loop-back test. LOOPEN is held low during standard operational state with external
serial outputs and inputs active.
RBC0
RBC1
31
30
Output
Receive byte clock. RBC0 and RBC1 are 62.5-MHz recovered clocks used for synchronizing the
10-bit output data on RD0 – RD9. The 10-bit output data words are valid on the rising edges of RBC0
and RBC1. These clocks are adjusted to half-word boundaries in conjunction with synchronous
detect. The clocks are always expanded during data realignment and never slivered or truncated.
RBC0 registers bytes 1 and 3 of received data. RBC1 registers bytes 0 and 2 of received data.
RC1,
RC0
49
48
Analog
Receive capacitor. RC0 and RC1 are external capacitor connections used for the receiver internal
PLL filter. The recommend value for this external capacitor is 2 nF (a value of 0.1 µF can also be used).
45,44,43,41
40,39,38,36
35,34
Output
Receive data. These outputs carry 10-bit parallel data output from the transceiver to the protocol
layer. The data is referenced to terminals RBC0 and RBC1. Received data byte 0, which contains the
K28.5 character, is byte aligned to the rising edge of RBC1. RD0 is the first bit received.
REFCLK
22
Input
Reference clock. REFCLK is an external 125 MHz input clock that synchronizes the receiver and
transmitter interfaces. The transmitter uses this clock to register the 10-bit input data (TD0..TD9) for
serialization. REFCLK is also used as a RX PLL preset or reference when LCKREFN is enabled.
SYNC
47
Output
Synchronous detect. SYNC is asserted high upon detection of the K28.5 character in the serial data
path. SYNC is a high level for 1/2 REFCLK period. SYNC pulses are output only when SYNCEN is
activated (asserted high). Note: SYNC is active on byte0 and, therefore, active on rising edge of
RCB1.
SYNCEN
24
Input
Synchronous function enable. When SYNCEN is asserted high, the internal synchronization function
is activated. When this function is enabled, the transceiver detects the K28.5 character (0011111010
negative beginning disparity) in the serial data stream and realigns data on byte boundaries if
required. When SYNCEN is low, serial input data is unframed in RD0 – RD9.
TC1
TC0
16
17
Analog
Transmit capacitor. TC0 and TC1 are external capacitor connections used for the transmitter internal
PLL filter. The recommended value of this external capacitor is 2 nF.
2,3,4,6
7,8,9,11
12,13
Input
Transmit data. These inputs carry 10-bit parallel data output from a protocol device to the transceiver
for serialization and transmission. This 10-bit parallel data is clocked into the transceiver on the rising
edge of REFCLK and transmitted as a serial stream with TD0 sent as the first bit.
I/O and DATA
RD0 – RD9
TD0 – TD9
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
Terminal Functions (Continued)
TERMINAL
NAME
DESCRIPTION
NO.
TYPE
20,28,29,53
55,57,59,60
63
Supply
Analog power. VCC_A provides a supply reference voltage for the high-speed analog circuits.
5,10,23,
Supply
Digital PECL logic power. VCC_CMOS provides an isolated low-noise power supply for the logic
circuits.
VCC_RX
50
Supply
Receiver power. VCC_RX provides a low-noise supply reference voltage for the receiver high-speed
analog circuits.
VCC_TTL
VCC_TX
42,37
Supply
TTL power. VCC_TTL provides a supply reference voltage for the receiver TTL circuits.
18
Supply
Transmitter power. VCC_TX provides a low-noise supply reference voltage for the transmitter
high-speed analog circuits.
21,32,56,64
Ground
Analog ground. GND_A provides a ground reference for the high-speed analog circuits.
1,14,
25,58
Ground
Digital PECL logic ground. GND_CMOS provides an isolated low-noise ground for the logic circuits.
GND_RX
51
Ground
Receiver ground. GND_RX provides a ground reference for the receiver circuits.
GND_TTL
33,46
Ground
TTL circuit ground. GND_TTL provides a ground for TTL interface circuits.
GND_TX
15
Ground
Transmitter ground. GND_TX provides a ground reference for the transmitter circuits.
RESERVED
26
POWER
VCC_A
VCC_CMOS
GROUND
GND_A
GND_CMOS
MISCELLANEOUS
Reserved. Internally pulled to GND, leave open or assert low.
detailed description
data transmission
The transmitter registers incoming 10-bit-wide data words (8b/10b encoded data, TD0..TD9) on the rising edge
of REFCLK (125 MHz). The reference clock is also used by the serializer, which multiplies the clock by a factor
of 10 providing a 1.25 Gbaud signal that is fed to the shift register. The data is then transmitted differentially at
PECL voltage levels. The 8b/10b encoded data is transmitted sequentially bit 0 through 9.
transmission latency
The data transmission latency of the TNETE2201 is defined as the delay from the initial 10-bit word load to the
serial transmission of bit 9. The typical transmission latency is 9 ns.
data reception
The receiver of the TNETE2201 deserializes 1.25 Gbps differential serial data. The 8b/10b data (or equivalent)
is retimed based on an extracted clock from the serial data. The serial data is then aligned to the 10-bit word
boundaries and presented to the protocol controller along with two receive byte clocks (RBC0, RBC1). RBC0
and RBC1 are 180 degrees out of phase and are generated by dividing down the recovered 1.25 Gbps
(625 MHz) clock by 10 providing for two 62.5-MHz signals. The receiver presents the protocol device byte 0 of
the received data valid on the rising edge of RBC1.
NOTE:
This allows the option of byte alignment without the use of the synchronous detection
(SYNC) function by the protocol device.
The receiver PLL can lock to the incoming 1.25 GHz data without the need for a lock-to-reference preset. The
received serial data rate (RX+ and RX–) should be 1.25 Gbps ± 0.01% (100 ppm) for proper operation.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
data reception (continued)
During a bus error condition or word alignment, the receive byte clocks RBC0 and RBC1 are stretched (never
truncated). When the incoming serial data does not meet its frequency requirements, then the receive byte clock
frequency is maintained at 62.5 MHz.
receive PLL operation
The receive PLL provides automatic locking to the incoming data. At power-up, the maximum initial lock time
is 500 µs. The PLL can also be initiated or set to phase lock to the externally supplied reference clock by enabling
lock-to-reference (LCKREFN). The lock-to-reference causes the receive PLL to lock to 10× the reference clock
(REFCLK) input providing a PLL preset and reset capability.
If a transient occurs during normal operation (a transient being defined as any arbitrary phase shift in the
incoming data and/or a frequency wander of up to 200 ppm), the PLL recovers lock within 2.4 µs. Any condition
exceeding these values is considered a power-up scenario with the PLL recovering lock within 500 µs. With a
0.1 µF capacitor attached, the PLL recovers lock within 10 ms on power up.
receiver word alignment
The TNETE2201 uses a 10-bit K28.5 character (comma character) word alignment scheme. The following
sections explain how this scheme works and how it realigns itself.
comma character on expected boundary
The TNETE2201 provides 10-bit K28.5 character recognition and word alignment. The 10-bit word alignment
is enabled by forcing SYCNEN high. This enables the function that examines and compares ten bits of serial
input data to the K28.5 synchronization character. The K28.5 character is defined in the fibre channel standard
as a pattern consisting of 0011111010 (a negative number beginning disparity) with the 7 MSBs (0011111)
referred to as the comma character. The K28.5 character was implemented specifically for aligning data words.
As long as the K28.5 character falls within the expected 10-bit word boundary, the received 10-bit data is
properly aligned and data realignment is not required. Figure 1 shows the timing characteristics of RBC0, RBC1,
SYNC and RD0 – RD9 while synchronized.
NOTE:
The K28.5 character is valid on the rising edge of RBC1.
RBC0
RBC1
SYNC
RD0 – RD9
K28.5
Dxx.x
Dxx.x
Dxx.x
K28.5
Dxx.x
Figure 1. Synchronous Timing Characteristics Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
comma character not on expected boundary
When synchronization is enabled and a K28.5 character straddles the expected 10-bit word boundary, then
word realignment is necessary. Realignment or shifting of the 10-bit word boundary truncates the character
following the misaligned K28.5, but the following K28.5 and all subsequent data is aligned properly as shown
in Figure 2. The 10b specification requires that RCLK cycles can not be truncated and can only be stretched
or stalled in their current state during realignment. With this design the maximum stretch that occurs is an extra
10 bit times. This occurs during a worst case scenario when the K28.5 is aligned to the falling edge of RBC1
instead of the rising edge. This system transmits a minimum of three consecutively ordered K28.5 data sets
between frames and ensures that the receiver sees at least two of K28.5 sets (the fabric is allowed to drop one).
Figure 2 shows the timing characteristics of the data realignment.
Systems that do not require framed data can disable byte alignment by tying SYNCEN low.
When a synchronization character is detected, the SYNC signal is asserted high and is aligned with the K28.5
character. The duration of the SYNC-signal pulse is equal to the duration of the data which is half an RCLK
period.
Typical Receive
Path Latency = 18 ns
Serial Rx Data Stream
DIN_RxP – DIN_RxN
K28.5
Dxx.x
Dxx.x
K28.5
Dxx.x
Dxx.x
Dxx.x
K28.5
Dxx.x
K28.5
Dxx.x
K28.5
10 Bit Times
10 Bit Times
20 Bit Times
(MAX)
RBC1
RBC0
Corrupted Data
Misalignment
Corrected
Worst Case
Misaligned K28.5
RD0 – RD9
Dxx.x
Dxx.x
K28.5
Dxx.x
Dxx.x
K28.5
Dxx.x
Dxx.x
SYNC
Figure 2. Word Realignment Timing Characteristics Waveforms
data reception latency
The serial-to-parallel data latency is the time from when the first bit arrives at the receiver until it is output in the
aligned parallel word with RD0 received as first bit. The receive latency is typically 18 ns.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
loop-back testing
The transceiver can provide a self-test function by enabling (LOOPEN to high level) the internal loop-back path.
Enabling LOOPEN causes serially transmitted data to be routed internally to the receiver. The parallel data
output can be compared to the parallel input data for functional verification. The external differential output is
held in a static state during loop-back testing.
absolute maximum ratings†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 to 4.0 V
Input voltage, VI (TTL, PECL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 to 4.0 V
Output current IO, (TTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Output current IO, (PECL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA
Voltage range at any terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 to VCC + 0.5 V
Electrostatic discharge, 5-V tolerant input terminals (see Note 2) . . . . . . . . . . . . . . Class 1, A:1 kV, B:150 V
Electrostatic discharge, all other terminals (see Note 2) . . . . . . . . . . . . . . . . . . . . . . Class 1, A:2 kV, B:200 V
Characterized free-air operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential I/O bus voltages, are with respect to network ground.
2. This parameter is tested in accordance with MIL-PRF-38535.
recommended operating conditions
PARAMETER
TEST CONDITIONS
Supply voltage, VCC
Supply current, ICC (static)
Static pattern†
Power Dissipation, PD (static)
Outputs Open,
Supply current, ICC (dynamic)
K28.5
Power Dissipation, PD (dynamic)
Outputs Open,
MIN
NOM
MAX
UNIT
3.14
3.3
3.47
V
180
260
mA
590
900
mW
static pattern†
K28.5
Operating free-air temperature, TA
† Power (static pattern) = 125 MHz to the receiver and 5 ones and 5 zeros to the transmitter.
240
330
mA
790
1150
mW
0
70
°C
reference clock (REFCLK) timing requirements over recommended operating conditions (unless
otherwise noted)†
PARAMETER
TEST CONDITIONS
Frequency
MIN
NOM
MAX
UNIT
TYP –
0.01%
125
TYP +
0.01%
MHz
100
ppm
Accuracy
–100
Duty cycle
40%
50%
60%
Jitter
Random and deterministic
40
ps
† This clock should be crystal referenced to meet the requirements listed in this table. The maximum rate of frequency change specified is valid
after 10 seconds from power on.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
electrical characteristics over recommended operating conditions (unless otherwise noted)
TTL Signals: TD0 .. TD9, REFCLK, LOOPEN, SYNCEN, SYNC, RD0 .. RD9, RBC0, RBC1, LCKREFN
PARAMETER
VOH
VOL
High-level output voltage
VIH
VIL
High-level input voltage
IIH
Low-level output voltage
IOH = – 400 µA
IOL = 1 mA
MIN
TYP
2.4
3
0.25
2
Low-level input voltage
Input High current
IIL
Input Low current
ci
Input capacitance
10
TEST CONDITIONS
VCC = MIN,
VCC = MIN,
REFCLK
VCC = MAX,
VCC = MAX,
VI = 2.4 V
VI = 2.4 V
REFCLK
VCC = MAX,
VCC = MAX,
VI = 0.4 V
VI = 0.4 V
MAX
V
0.4
V
5.5
V
0.8
V
40
µA
900
µA
µA
–40
µA
–900
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
pF
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
TRANSMITTER SECTION
differential electrical characteristics over recommended operating conditions (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
VOD
(peak to peak)
Driver differential output voltage (peak-to-peak)
VOC
Driver common-mode output voltage
MIN
TYP
MAX
RL = 75 Ω,
See Figure 3
1100
2200
RL = 50 Ω,
See Figure 3
1100
2200
RL = 75 Ω
2100
UNIT
mV
mV
differential switching characteristics over recommended operating conditions (unless otherwise
noted).
PARAMETER
tr3
tf3
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Serial data deterministic jitter (peak-to-peak)
Differential output jitter
96
ps
Serial data total jitter (peak-to-peak)
Differential output jitter
192
ps
Differential signal rise time (20% to 80%)
RL = 75 Ω,
S Figure
See
Fi
3
300
ps
300
ps
Differential signal fall time (20% to 80%)
CL = 5 pF,
80%
TX+
≈ VCC – 0.7 V
50%
20%
≈ VCC – 1.6 V
80%
≈ VCC – 0.7 V
tf
tr
TX–
50%
20%
≈ VCC – 1.6 V
80%
≈1 V
tr
tf
VOD
50%
20%
≈ –1 V
tf3
tr3
Figure 3. Differential and Common-Mode Output Voltage Definitions
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
transmitter timing requirements over recommended operating conditions (unless otherwise
noted)
TEST CONDITIONS
tsu1
th1
MIN
Setup time, TD0 – TD9 valid to REFCLK ↑
See Figure 4
2
Hold time, REFCLK ↑ to TD0 – TD9 invalid
See Figure 4
1
Parallel-to-serial data latency
NOM
MAX
UNIT
ns
ns
9
ns
transmit interface timing
The transmit interface is defined in the 10 b spec as the 10-bit parallel data input to the physical layer for serial
transmission. The timing values are specified from REFCLK midpoint to valid input signal levels or from valid
input signal levels to REFCLK midpoint.
50%
REFCLK
tsu1
th1
ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉ ÉÉÉÉÉÉÉ
TD0 – TD9
Valid
Valid
Figure 4. Transmit 10-Bit Interface Timing Waveforms
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Valid
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
RECEIVER SECTION
differential electrical characteristics over recommended operating conditions (unless otherwise
noted)
PARAMETER
|VID |
Differential input voltage (peak-to-peak)
TEST CONDITIONS
MIN
See Figure 5
400
TYP
MAX
UNIT
2600
mV
receiver and phase-locked loop performance characteristics over recommended operating
conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Jitter tolerance
MIN
TYP
See P802.3Z specification
From power up at 2 nF capacitor value
Data acquisition lock time
From power up at 0.1 µF capacitor value
Data relock time
† UI is the unit interval of a single bit (800 ps).
From synchronization loss
MAX
UNIT†
74.9%
UI
500
µs
10
ms
2500
ns
receive clock timing requirements over recommended operating conditions (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
fclk
fclk
Clock frequency, RBC0
62.5
Clock frequency, RBC1 (180 deg out of phase with RBC0)
62.5
tr4
tf4
Data Rise time
See Figure 6
0.7
4
ns
Data Fall time
See Figure 6
0.7
4
ns
tr5
tf5
Rise time, single-ended output signal on RBC0 or RBC1
See Figure 6
0.7
2
ns
Fall time, single-ended output signal on RBC0 or RBC1
See Figure 6
0.7
2
ns
40%
60%
Duty cycle, RBC0 or RBC1
MHz
MHz
t(skew)
tsu2
Skew time, RBC1 ↑ to RBC0 ↑
See Figure 7
7.5
Setup time, RD0 – RD9, SYNC valid to RBC0 ↑
See Figure 7
2.5
ns
tsu3
tsu4
Setup time, RD0 – RD9, SYNC valid to RBC1 ↑
See Figure 7
2.5
ns
Setup time, RBC1 ↑ to RD0 – RD9, SYNC invalid
See Figure 7
1.5
ns
tsu5
Setup time, RBC1 ↑ to RD0 – RD9, SYNC invalid
See Figure 7
1.5
Serial-to-parallel data latency
8
8.5
ns
ns
18
ns
† t(drift) is the minimum time for RBC0 or RBC1 to drift from 63.5 MHz to 64.5 MHz or from 60 MHz to 59 MHz from the RCLK lock value. This is
applicable under all input signal conditions with PLL locked to the REFCLK of DATA signals.
| VID |
0V
| VID |
Figure 5. Differential Input Voltage (Peak-to-Peak) Timing Waveform
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
80%
50%
Data
20%
tf4
tr4
80%
Clock
50%
20%
tf5
tr5
Figure 6. Receiver Data Measurement Levels
t(skew)
50%
50%
RBC0
50%
RBC1
50%
tsu2
tsu3
tsu5
ÉÉÉ ÉÉÉ ÉÉÉ ÉÉ ÉÉ ÉÉ
ÉÉÉ ÉÉÉ ÉÉÉ ÉÉ ÉÉ ÉÉ
tsu4
RD0 – RD9, SYNC
Valid
Valid
Valid
Valid
Figure 7. Receiver Interface Timing Waveforms
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Valid
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
APPLICATION INFORMATION
Ferrite Bead
Ferrite Bead
3.3 V
50
0.01 µF
VCC_RX
51
5 Ω at 100 MHz
18
VCC_TX
GND_RX
GND_TX
TNETE2201
DOUT_TXP
15
3.3 V
0.01 µF
62
Controlled Impedance
Transmission Line
R(pd)
(see Note A)
10
/
TD0 – TD9
22
27
19
Host
Protocol
Device
24
47
2
/
10
/
REFCLK
DOUT_TXN
61
Controlled Impedance
Transmission Line
54
Controlled Impedance
Transmission Line
LCKREFN
LOOPEN
SYNCEN
SYNC
DOUT_RXP
RD0 – RD9
31,30
50 Ω – 75 Ω
RBC0,RBC1
Vt
(see Note B)
50 Ω – 75 Ω
DOUT_RXN
49
PLL Filter
Capacitor = 2.2 nF or 0.1 µF
48
RC1
RC0
TC1
TC0
52
Controlled Impedance
Transmission Line
16
17
PLL Filter
Capacitor = 2.2 nF or 0.1 µF
NOTES: A. R(pd) – This value is set to match the falling edge to rising edge transistion times, typically 150 Ω. to 220 Ω..
B. Vt (termination voltage): Vt = VCC – 1.3 V, if ac coupled
Vt = VCC – 2 V, if directly coupled.
Figure 8. Typical Application Circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
MECHANICAL INFORMATION
The TNETE2201 incorporates the latest development in TI’s package line. The new patent-pending design,
designated the PWP, delivers thermal performance comparative to a heat-spreader design in a true low-profile
package. The PWP for the TNETE2201 is designed to maximize heat transfer away from the die through the
top of the chip. As seen in Figures 9 and 10 the bottom of the leadframe is deep downset towards the top of
the chip, providing a thermal path away from the die and board. All this has been accomplished without
exceeding the 1.15 mm height of the TQFP. This package in the 10mm × 10mm TQFP (PJD) provides a thermal
resistance RθJA of 40°C/W and the package in the 14mm × 14mm TQFP (PHD) provides a RθJA of 40°C/W.
Figure 9. Heat-Spreader Design
Figure 10. Leadframe Downset
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
MECHANICAL INFORMATION
PHD (S-PQFP-G64)
PowerPAD PLASTIC QUAD FLATPACK (DIE DOWN)
0,40
0,30
0,80
48
0,20 M
33
32
49
Thermal Pad
(see Note D)
0,13 NOM
64
17
Gage Plane
1
16
12,00 TYP
14,05
SQ
13,95
0,25
0,15
0,05
0°– 7°
0,75
0,45
16,15
SQ
15,85
1,05
0,95
Seating Plane
0,10
1,20 MAX
4087742/A 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions include mold flash or protrusions.
The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad. This pad is electrically
and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MS-026
PowerPAD is a trademark of Texas Instruments Incorporated.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TNETE2201
1.25-GIGABIT ETHERNET TRANSCEIVER
SLLS267D – JUNE 1997 – REVISED FEBRUARY 1999
MECHANICAL INFORMATION
PJD (S-PQFP-G64)
PowerPAD PLASTIC QUAD FLATPACK (DIE DOWN)
0,27
0,17
0,50
48
0,08 M
33
32
49
Thermal Pad
(See Note D)
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,15
0,05
1,05
0,95
0°– 7°
0,75
0,45
Seating Plane
0,08
1,20 MAX
4147703/A 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions include mold flash or protrusions.
The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad. This pad is electrically
and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MS-026
PowerPAD is a trademark of Texas Instruments Incorporated.
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
4-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TNETE2201PHD
OBSOLETE
HTQFP
PHD
64
None
Call TI
Call TI
TNETE2201PJD
OBSOLETE
HTQFP
PJD
64
None
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated