358 8-Channel Fault-Protected Analog Multiplexer Memory Logic Diagram FEATURES: DESCRIPTION: • RAD-PAK® technology-hardened against natural space radiation • Total dose hardness: - > 50 krad (Si), depending upon space mission • Excellent Single Event Effect - SELTH > 80 MeV/mg/cm2 Maxwells’s 358 8-Channel single-ended (1 of 8) multiplexers with fault protection features a greater than 50 krad (Si) total dose tolerance, depending upon space mission. Using a series N-channel, P-channel, N-channel structure, these multiplexers provide significantly improved fault protection. If the power supplies to the fault-protected multiplexer are inadvertently turned off while input voltages are still applied, all channels in the multiplexer are turned off, and only a few nanoamperes of leakage current will flow into the inputs. This protects not only the multiplexer and the circuitry driven by the multiplexer, but also protects the sensors or signal sources which drive the multiplexer. All digital inputs have logic thresholds of 0.8V and 2.4V, ensuring both TTL and CMOS compatibility without requiring pullup resistors. Break-before-make operation is guaranteed. Power supply currents have been reduced and typical power dissipation is less than 2 mW. • • • • • • • - SEUTH > 80 MeV/mg/cm2 Package: - 16 pin RAD-PAK® Flat Pack All switches off with power supplies off On channel turns OFF if overvoltage occurs Only nanoamperes of input current under all fault conditions Operates from ±4.5 to ±18V supplies All digital inputs are TTL and CMOS compatible Significantly reduced power consumption Maxwell Technologies' patented RAD-PAK® packaging technology incorporates radiation shielding in the microcircuit package. It eliminates the need for box shielding while providing the required radiation shielding for a lifetime in orbit or a space mission. In a GEO orbit, Rad-Pak® provides true greater than 50 krad (Si) total radiation dose tolerance, dependent upon space mission. This product is available with packaging and screening up to Class S. 02.06.04 Rev 3 (858) 503-3000 - Fax: (858) 503-3301 - www.maxwell.com All data sheets are subject to change without notice 1 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer TABLE 1. PINOUT DESCRIPTION PIN SYMBOL DESCRIPTION 1, 16, 15 A0-A2 Address Inputs 2 Enable Enable Inputs 3 -V Supply 4-7, 12-9 IN1-IN8 8 OUT 13 +V Supply 14 GND Negative Supply Voltage Analog Inputs-bidirectional Output-bidirectional Positive Supply Voltage Ground TABLE 2. 358 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL UNITS Voltage between Supply Pins V+ V- +44 +22 -22 V Digital Input Overvoltage VEN, VA Vsupply (+) Vsupply (-) +4 -4 V Analog Input Overvoltage with Multiplexer Power On: VS Vsupply (+) Vsupply (-) +20 -20 V Analog Input Overvoltage with Multiplexer Power Off: VS Vsupply (+) Vsupply (-) +35 -35 V 20 40 mA 2.69 °C/W 2.25 Grams Continuous Current Peak Current (Pulse at 1 ms, 10% duty cycle max) Thermal Impedance ΘJC Weight Operating Temperature Range: TA -55 to +125 °C Storage Temperature Range: TS -65 to +150 °C 02.06.04 Rev 3 All data sheets are subject to change without notice Memory MAX 2 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer TABLE 3. 358 ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, VAH = 2.4V, VAL = 0.8V, TA = -55 TO +125°C, UNLESS OTHERWISE SPECIFIED) PARAMETER TEST CONDITIONS SUBGROUPS SYMBOL TEMP 1, 2, 3 rDS(ON) OFF Input Leakage Cur- VS = ±10V, VD = +10V rent VEN = 0.8V 1, 2, 3 IS(OFF) OFF Output Leakage Current VD = ±10V, VS = +10V VEN = 0.8V 1, 2, 3 ON Channel Leakage Current VS(ALL) = VD = ±10V1 VAH = VEN = 2.4V VAL = 0.8V 1, 2, 3 Analog Signal Range 2 1, 2, 3 VAN Full 1, 2, 3 ID(OFF) +25°C Full MIN TYP MAX UNITS +25°C Full 1.2 1.5 1.5 1.8 kΩ +25°C Full 0.03 +25°C Full 0.1 +25°C Full 0.1 STATIC ON Resistance VD = ±10V, IS = ±100µ A VAL = 0.8V, VAH = 2.4V ID(OFF) ID(ON) nA 50 nA 200 nA 2002 -15 15 V 2.0 nA µA FAULT 4.0 Input Leakage Current (with Overvoltage) VIN = ±25V, VO = ±10V1 1, 2, 3 IS(OFF) +25°C 5.0 µA Input Leakage Current (w/ Power Supplies Off) VIN = ±25V, VEN = VO = 0V AO = A1 = A2 = OV or 5V 1, 2, 3 IS(OFF) +25°C 2.0 µA 1, 2, 3 VAL Full 0.8 V 1, 2, 3 VAH Full 1, 2, 3 IA Full 1, 2, 3 tA +25°C 9, 10, 11 ton-toff +25°C Enable Delay (ON) 9, 10, 11 ton(EN) +25°C Full 300 500 1000 ns Enable Delay (OFF) 9, 10, 11 toff(EN) +25°C Full 300 500 1000 ns Setting Time: (0.1%) (0.01%) 9, 10, 11 tsett +25°C 1.2 3.5 µs 68 db Memory Output Leakage Current VD = 0V1 (with Overvoltage) Analog Overvoltage = ±33V INPUT Input Low Threshold Input High Threshold Input Leakage Current (High or Low) VA = 4V or 0V3 2.4 V 1.0 µA 1.0 µs DYNAMIC Access Time Break-Before-Make Delay “OFF Isolation”4 VEN = ±5V, VIN = ±10V AO, A1, A2 Strobed VEN = 0.8V, RL = 1kΩ CL = 15pF, V = 7VRMS f = 100kHz 4, 5, 6 02.06.04 Rev 3 +25°C 0.5 25 50 80 ns All data sheets are subject to change without notice 3 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer TABLE 3. 358 ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, VAH = 2.4V, VAL = 0.8V, TA = -55 TO +125°C, UNLESS OTHERWISE SPECIFIED) PARAMETER TEST CONDITIONS SUBGROUPS SYMBOL TEMP MIN TYP MAX UNITS Channel Input Capacitance4 4, 5, 6 CS(OFF) +25°C 5 pF Channel Output Capacitance4 4, 5, 6 CD(OFF) +25°C 25 pF Digital Input Capacitance4 4, 5, 6 CA +25°C 5 pF Digital Output Capacitance4 4, 5, 6 CDS(OFF) +25°C 0.1 pF VEN = 0.8V or 2.4V VA = 0V or 5V 1, 2, 3 I+ +25°C Full 0.1 0.3 0.6 0.7 mA Negative Supply Current VEN = 0.8V or 2.4V VA = 0V or 5V 1, 2, 3 I- +25°C Full 0.01 0.02 0.1 0.2 mA 1, 2, 3 VOP +25°C ±18 V SUPPLY Positive Supply Current 5 ±4.5 1. The value shown is the steady state value. The transient leakage is typically 10 µ A. 2. When the analog signal exceeds +13.5V or -12V the blocking action of the gate structure goes into operation. Only leakage currents flow and the channel on resistance rises to infinity. 3. Digital input leakage is primarily due to the clamp diodes. Typical leakage is less than 1 nA @ +25°C. 4. Guaranteed by design. 5. Electrical characteristics, such as ON Resistance, will change when power supplies other than ±15V are used. 02.06.04 Rev 3 All data sheets are subject to change without notice 4 ©2004 Maxwell Technologies All rights reserved. Memory Power Supply Range for Continuous Operation 358 8-Channel Fault-Protected Analog Multiplexer FIGURE 1. INPUT LEAKAGE VS. INPUT VOLTAGE WITH V+ = V- = 0V FIGURE 2. OFF CHANNEL LEAKAGE CURRENT VS. INPUT VOLTAGE WITH ±15V SUPPLIES Memory FIGURE 3. OUTPUT LEAKAGE VS. OFF CHANNEL OVERVOLTAGE WITH ±15V SUPPLIES 02.06.04 Rev 3 All data sheets are subject to change without notice 5 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer FIGURE 4. RDS(ON) VS. INPUT VOLTAGE A2 A1 A0 EN ON SWITCH X X X 0 NONE 0 0 0 1 1 0 0 1 1 2 0 1 0 1 3 0 1 1 1 4 1 0 0 1 5 1 0 1 1 6 1 1 0 1 7 1 1 1 1 8 Memory TRUTH TABLE Logic “0” = VAL < 0.8V, Logic “1” = VAH > 2.4V 02.06.04 Rev 3 All data sheets are subject to change without notice 6 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer Memory L E3 16-PIN RAD-PAK® FLAT PACK PACKAGE DIMENSIONS SYMBOL MIN NOM MAX A .115 .135 .150 b .015 .017 .019 c .004 .005 .007 D 0.407 .415 .423 E .275 .280 .285 E1 -- -- 0.500 E2 .150 .156 0.162 E3 .030 .062 -- e .050 BSC L .325 .335 .345 Q .020 .033 .045 S1 .005 .024 0.045 N 16 All dimensions in inches 02.06.04 Rev 3 All data sheets are subject to change without notice 7 ©2004 Maxwell Technologies All rights reserved. 8-Channel Fault-Protected Analog Multiplexer 358 Important Notice: These data sheets are created using the chip manufacturer’s published specifications. Maxwell Technologies verifies functionality by testing key parameters either by 100% testing, sample testing or characterization. The specifications presented within these data sheets represent the latest and most accurate information available to date. However, these specifications are subject to change without notice and Maxwell Technologies assumes no responsibility for the use of this information. Maxwell Technologies’ products are not authorized for use as critical components in life support devices or systems without express written approval from Maxwell Technologies. Any claim against Maxwell Technologies must be made within 90 days from the date of shipment from Maxwell Technologies. Maxwell Technologies’ liability shall be limited to replacement of defective parts. Memory 02.06.04 Rev 3 All data sheets are subject to change without notice 8 ©2004 Maxwell Technologies All rights reserved. 358 8-Channel Fault-Protected Analog Multiplexer Product Ordering Options Model Number 358 RP F X Option Details Feature Monolithic S = Maxwell Class S B = Maxwell Class B I = Industrial (testing @ -55°C, +25°C, +125°C) E = Engineering (testing @ +25°C Package F = Flat Pack Radiation Feature RP = RAD-PAK® package Base Product Nomenclature 8-Channel Fault-Protected Analog Multiplexer 02.06.04 Rev 3 All data sheets are subject to change without notice Memory Screening Flow 9 ©2004 Maxwell Technologies All rights reserved.