66056 Mii SINGLE/DUAL CHANNEL, HERMETICALLY SEALED, VERY HIGH SPEED OPTOCOUPLER OPTOELECTRONIC PRODUCTS DIVISION Rev 1 7/3/01 Features: Applications: • • • • • • • • • • • DSCC Approved 8102802PX (Dual); and single channel version optocoupler 10 MHz bandwidth typical 1500 Vdc isolation test voltage TTL compatible input and output High radiation immunity Faraday shield to provide high common mode rejection Military and space Voltage level shifting Isolated receiver input Communication systems Medical systems DESCRIPTION The 66056 single and dual channel optocouplers consist of LED’s optically coupled to two high speed, high gain inverting detector gates. Maximum isolation can be achieved while providing TTL outputs capable of switching with propagation delays of 55ns typical. The 66056 is available in military temperature range and military temperature with 100% device screening. The devices are built in eight-pin dual-in-line, hermetically sealed packages and provide high input to output DC isolation. ABSOLUTE MAXIMUM RATINGS Storage Temperature ............................................................................................................................................ -65°C to +150°C Operating Free-Air Temperature Range ............................................................................................................... -55°C to +125°C Lead Solder Temperature ..........................................................................................260°C for 10s (1.6mm below seating plane) Peak Forward Input Current (each channel) .................................................................................................40mA (1ms duration) Average Forward Input Current (each channel)…(see Note 1) ............................................................................................ 20mA Input Power Dissipation (each channel) ............................................................................................................................... 35mW Reverse Input Voltage (each channel) ........................................................................................................................................5V Supply voltage - VCC .................................................................................................................................. 7V(1 minute maximum) Output Current - IO (each channel) ........................................................................................................................................ 25mA Output Power Dissipation (each channel) ............................................................................................................................ 40mW Output Voltage - VO (each channel) ............................................................................................................................................7V Total Power Dissipation (per channels) .............................................................................................................................. 175mW NOTES: 1. Derate IF at 0.05mA/°C above 25°C. Package Dimensions Schematic Diagrams S in g le C h a n n e l V cc DATE CODE 0 .3 7 0 [9 .0 4 0 ] 0 .3 9 0 [9 .9 0 ] 8 7 6 5 YYW W USA XXXX P IN O N E 1 2 3 Vo 2 0 .1 7 0 [4 .3 2 ]M A X 0 .2 8 0 [7 .1 1 ] 0 .3 1 0 [7 .8 8 ] 0 .3 2 0 [8 .1 3 ]M A X TYPE NUM BER R E A R V IE W K GND 8 6 5 D ual C hannel P IN O N E 0 .0 0 7 [0 .1 8 ] 0 .0 1 3 [0 .3 3 ] 4 3 A 0 .0 2 0 [0 .5 1 ] M IN 2 0 .0 9 0 [2 .2 8 ] 0 .1 1 0 [2 .8 0 ] V o1 1 NOTE: V o2 A L L D I M E N S I O N S A R E IN IN C H E S [M IL L IM E T E R S ] NOTE: A .0 1 to .1 u F b y p a s s c a p a c ito r m u s t b e p la c e d b e tw e e n V c c a n d G n d 6 5 A K GND MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: [email protected] 3 - 34 8 7 K E N D V IE W S ID E V IE W V cc A .0 2 0 [0 .5 1 ] M A X 6 5 66056 Rev 1 SINGLE/DUAL CHANNEL, HERMETICALLY SEALED, VERY HIGH SPEED OPTOCOUPLER 7/3/01 ELECTRICAL CHARACTERISTICS PARAMETER Ta=-55°C to at 125°C unless otherwise specified. SYMBOL TYP MAX UNITS TEST CONDITIONS High Level Output Current IOH MIN 5 250 µA VCC = 5.5V, VO = 5.5V,IF =250µA NOTE 1 Low Level Output Voltage VOL 0.5 0.6 V VCC = 5.5V, IF = 10mA 1,3 ICCH 9 14 mA VCC = 5.5V, IF = 0 18 28 ICCL 13 18 mA VCC = 5.5V, IF = 20mA 26 36 VF 1.5 1.75 IOL (Sinking) = 10mA High Level Supply Current Single Channel Dual Channel Low Level Supply Current Single Channel Dual Channel Input Forward Voltage Input Reverse Breakdown Voltage BVR Input-Output Insulation Leakage Current II—O (Both Channels) (Both Channels) 5 1.0 V IF = 20mA V IR = 10µA µA 1 VI—0 = 1500Vdc, 2 Relative Humidity = 45% ta = 25°C, t = 5s Propagation Delay Time To High Output Level tPLH 45 100 RL = 510Ω, CL = 50pF. ns 3,4 If = 13mA, ta = 25°C Propagation Delay Time To Low Output Level tPHL 55 100 RL = 510Ω, CL = 50pF ns 3,5 If = 13mA, ta = 25°C TYPICAL CHARACTERISTICS TA = 25°C, VCC = 5V EACH CHANNEL PARAMETER SYMBOL MIN TYP MAX Input Capacitance Input Diode Temperature Coefficient UNITS TEST CONDITIONS CIN 60 pF VF = 0, f = MHz 1 ∆vF ∆TA -1.9 mV/°C IF = 20mA 1 12 NOTE Resistance (Input-Output) RI-0 10 Ω VI—O = 500V 2 Capacitance (Input-Output) CI-O 5 pF f = 1MHz 2 Output Rise-Fall Time (10-90%) t r, t f 35 ns RL = 510Ω, CL = 50pFIF = 13mA Common Mode Transient Immunity at High Output Level CMH 1000 10000 V/µs VCM = 10V (peak), VO (min) = 2V, RL = 510Ω, IF = OmA 6 Common Mode Transient Immunity at Low Output Level CML 1000 10000 V/µs VCM = 10V (peak), VO (max) = 0.8V, RL = 510Ω, IF = 1OmA 7 NOTES: 1. Each channel 2. Measured between input pins shorted together and output pins shorted together. 3. It is essential that a bypass capacitor (.01 to 0.1µF ceramic) be connected from pin 1 to pin 4. 4. The tplh propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output pulse. 5. The tphl propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output pulse. 6. CMh is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. Vo >2.0V). 7. CMl is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. Vo < 0.8V). RECOMMENDED OPERATING CONDITIONS: PARAMETER SYMBOL MIN MAX Input Current, Low Level Each Channel IFL 0 250 UNITS µA Input Current, High Level Each Channel IFH 12.5 20 mA Supply Voltage VC 4.5 5.5 V Fan Out (TTL Load) Each Channel N Operating Temperature TA 6 -55 125 ° C SELECTION GUIDE PART NUMBER 66056-011 66056-012 66056-001 66056-002 66056-101 66056-102 66056-103 PART DESCRIPTION Single Channel, commercial optocoupler Dual Channel, commercial optocoupler Single Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C) Dual Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C) Single Channel optocoupler tested over full military temperature range with 100% device screening Dual Channel optocoupler tested over full military temperature range with 100% device screening DSCC Dwg 8102802PX Dual channel optocoupler MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918 www.micropac.com E-MAIL: [email protected] 3 - 35