MITEL NWK933CG

NWK933
NWK933
3.3V 10/100 Fast Ethernet Transceiver to MII
DS5029
Issue no 2.1
May 1999
Features
Odering Information
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Integrated 10/100 Mbps Ethernet in a Single Chip
Solution
Single 3.3V Power Supply
Half Duplex and Full Duplex in both 10BASE-T
and 100BASE-TX
Full MII for a Glueless MAC Connection
Extended Register Set
Integrated 10BASE-T Transceivers and Receive /
Transmit Filters
Integrated Adaptive Equaliser and Base Line
Wander Correction (for FDDI Killer Packet)
Full Auto-Negotiation Support for 10BASE-T and
100BASE-TX both Half and Full Duplex
Link Status Change Interrupt
Parallel Detection for Supporting Non Auto
Negotiation in Legacy Link Partners
Low Dynamic Current
Deep Sleep Low Power Mode <1mA
Internal Power on Reset
64 pin 1mm thick TQFP Package
Single Magnetics for 10BASE-T and 100BASE-TX
Operation for a Single RJ45 Connector
Support for Flow Control 802.3 Specification
Integrated 6 LED Driver
Switch or MAC
NWK933/CG/TP1N
●
●
●
●
Low External Component Count
Loop-back mode for diagnostics
Intelligent power management
(auto shutdown, auto wake)
Low Transmit Jitter
Description
The NWK933 is a single chip 3.3V CMOS physical
layer solution from MII to the magnetics. It is designed
for 10BASE-T and 100BASE-TX Ethernet, based
on the IEEE 802.3 specifications.
The NWK933 is compatible with the Auto Negotiation
section of IEEE 802.3u and provides all the support
needed for the 802.3 Full duplex specification.
NWK933
Isolation
Magnetics
RJ45
Figure 1 System block diagram
1
64 TX_CLK
63 TX03
62 TXD2
61 TXD1
60 TXD0
59 RX_ER
58 RXD3
57 RXD2
56 RXD1
55 RXD0
54 DVDD2
53 RX_CLK
52 DGND2
51 RX_DV
50 CRS
49 COL
NWK933
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
MINT
DVDD3
MDC
MDIO
DGND3
RefCLK
OSCVDD
XTAL1
XTAL2
OSCGND
TXGND4
TXVDD4
TXREF100
TXREF10
TXVDD3
TXGND3
PA3 17
RXGND1 18
RXIP 19
RXIN 20
RXVDD1 21
ANEN 22
TXOP 23
TXVDD2 24
TXGND2 25
TXGND1 26
TXVDD1 27
TXON 28
PA2 29
PA1 30
PA0 31
SUBGND1 32
SUBGND2 1
TX_ER 2
DGND1 3
TX_EN 4
LNKST 5
ACTST 6
COLST 7
DVDD1 8
RXVDD3 9
RXGND3 10
FDST 11
SPDST 12
PA4 13
RESETN 14
RXVDD2 15
RXGND2 16
TP64
Figure 2Pin connections
Functional Description
10Base-T Operation
The NWK933 has three basic modes of operation:
10BASE-T, 100BASE-TX and LOW POWER modes.
The Control block is designed to manage these modes
by starting and stopping the 10M and 100M transceivers
in a well-controlled manner such that no spurious
signals are output on either the MII or twisted-pair
interfaces. Furthermore, it continuously monitors the
behaviour of the transceivers and takes corrective
action if a fault is detected.
10Mb/s Data Transfer on the MII
Other modes described herein are repeater mode and
reset mode.
25MHz Reference Clock
The NWK933 requires a 25MHz +/-100ppm timing
reference for 802.3 compatible operation. This may
be supplied either from the integrated oscillator or
from an external source. When the integrated oscillator
is used, a suitable crystal must be connected across
the XTAL1 & XTAL2 pins (see “External Components”)
and REFCLK must be tied low. When an external
source is used, it must be input to the REFCLK pin
and XTAL1 must be tied low. XTAL2 must be
unconnected.
2
10Mb/s data is transferred across the MII with clock
speeds of 2.5MHz. The MAC outputs data to the
NWK933 via the MII interface, on the TXD[3:0] bus.
This data is synchronised to the rising edge of TX_CLK.
To indicate that there is valid data for transmission on
the MII, the MAC sets the TX_EN signal active. This
forces the NWK933 device to take in the data on the
TXD[3:0] bus. This is serialised and directly encoded
as Manchester data, before being output on the TXOP/
TXON differential output for transmission through 1:Ö2
magnetics and onto the twisted-pair.
The transmit current is governed by the current through
the TXREF10 pin, which must be grounded through a
resistor as described in “External Components”.
RX10 Clock Recovery
The NWK933 employs a digital delay line controlled
by the 100MHz Synthesizer DLL to derive a sampling
clock from the incoming signal. The recovered clock
runs at twice the data rate (nominally 20MHz). When
a signal is received from the Signal Detect block, it is
used to strobe Link Pulses and Manchester encoded
serial data.
NWK933
The Manchester data stream will be decoded into a 4bit parallel data bus, RXD[3:0]. The RXD bus is clocked
out on RX_CLK rising. The NWK933 must detect the
first 4 bits of pre-amble before RX_DV is set high.
When RX_DV is high, any Manchester coding violation
will set RX_ER high. RX_DV is reset by a continuous
sequence of zeroes, or by the end-of-packet IDLE
terminator (11 11 00 00). Whilst RX_DV is low, the
data is invalid.
RX10 Latency
100MHz Synthesizer
100Base-TX Operation
This synthesizer employs a delay-locked loop (DLL)
to generate a 100MHz timing reference from the 25MHz
reference clock. This 100MHz reference is used by
the 10BASE-T transmit and receive functions and is
divided by 5 to provide a 20MHz data strobe. The
20MHz clock is used to derive the 2.5 MHz TX_CLK in
10BASE-T mode. The synthesizer is disabled when
not in 10BASE-T mode.
100Mb/s Data Exchange on the MII Interface
TX10 Pulse Shaper & Filter
The Pulse Shaper & Filter employs a digital Finite
Impulse Response filter (FIR) to pre-compensate for
line distortion and to remove high frequency
components in accordance with the 802.3 Standard.
The Pulse Shaper & Filter is disabled when not in
10BASE-T mode.
TX10 Latency
When connected to appropriate magnetics the latency
through the TX10 path is less than 2BT (200ns) for
data transmissions. This timing is measured from the
rising edge of TX_CLK to the output of the transmit
magnetics. The TX10 path will not transmit up to the
first two Manchester encoded bits of a data
transmission, as permitted by the 802.3 Standard.
RX10 Filter & RX10 Signal Detect
These blocks work in unison to remove noise and to
block signals that do not achieve the voltage levels
specified in 802.3. Signals that do not achieve the
required level are not sampled in the Clock Recovery
block and are not passed to the outputs.
When connected to appropriate magnetics the latency
through the RX10 path is less than 6BT (600ns). This
timing is measured from the input of the receive
magnetics to the rising edge of RX_CLK. The RX10
path may ignore up to three Manchester encoded bits
at the start of data reception (802.3 allows up to 5
bits).
100Mb/s data is transferred across the MII with clock
speeds of 25MHz. The MAC outputs data to the
NWK933 via the MII interface, on the TXD[3:0] bus.
This data is synchronised to the rising edge of TX_CLK.
To indicate that there is valid data for transmission on
the MII, the MAC sets the TX_EN signal active. This
forces the NWK933 device to take in the data on the
TXD[3:0] bus and replace the first octet of the MAC
preamble with Start-of-Stream Delimiter (SSD) symbols
to indicate the start of the Physical Layer Stream.
When the data transfer across the MII is complete, the
MAC deasserts the TX_EN signal and the NWK933
adds End-of-Stream Delimiters (ESD) symbols onto
the end of the data stream. The complete data stream
(the Physical Layer Stream) is encoded from 4 bits
into 5 bits, scrambled, converted to MLT3 and driven
to the TXOP and TXON pin differentially.
The TX100 path is disabled when not in 100BASE-TX
mode and, with the exception of the RX100 Signal
Detect, the RX100 Receive Path is disabled when not in
100BASE-TX mode.
125MHz Synthesizer
This synthesizer employs a phase-locked loop (PLL) to
generate a 125MHz timing reference from the 25MHz
reference clock. This 125MHz reference is used by the
100BASE-TX transmit function and is divided by 5 to
provide a 25MHz data strobe on TX_CLK. TX_CLK is
frequency and phase locked to the 25MHz reference
with a small phase offset. The synthesizer is disabled
when not in 100BASE-TX mode.
3
NWK933
TX100 PISO, Encoder and Scrambler
RX100 Clock Recovery
Data from the MII is loaded into the TX100 PISO,
Encoder and Scrambler on the rising edge of TX_CLK.
It is converted to serial MLT3 for outputting to the
TX100 Driver. The TXD[3] bit is output first. The
PISO & Encoder do not operate until the 125MHz
Synthesizer is locked to the 25MHz reference. This
avoids transmission of spurious signals onto the
twisted-pair.
The RX100 Clock Recovery circuit uses a PhaseLocked Loop (PLL) to derive a sampling clock from
the incoming signal. The recovered clock runs at the
symbol bit rate rate (nominally 125MHz) and is used
to clock the MLT3 decoder and the Serial to Parallel
converter (SIPO).
TX100 Driver
The TX100 Driver outputs the differential signal onto
the TXOP and TXON pins. It operates with 1:root 2
magnetics to provide impedance matching and
amplification of the signal in accordance with the
802.3 specifications. The transmit current is governed
by the current through the TXREF100 pin, which
must be grounded through a resistor as described in
“External Components”. The TX100 driver is disabled
in 10BASE-T mode and in loop back mode.If no data
is being transmitted from the MAC, the NWK933
outputs idle symbols of 11111 (suitably scrambled).
TX100 Latency
The transmit latency from the first TX_CLK rising
when TX_EN is high to the first bit of the “J” symbol
on the cable is 8BT.
RX100 Equalizer & Base-line Wander
Correction
The RX100 Equalizer compensates for the signal
attenuation and distortion resulting from transmission
down the cable and through the isolation transformers.
The Equalizer is self-adjusting and is designed to
restore signals received from up to 10dB cable
attenuation (at 16MHz). When the Equalizer is active
it adjusts to the incoming signal within 1ms. Thereafter,
the Equalizer will continuously adjust to small
variations in signal level without corrupting the
received data.
The 100BASE-TX MLT3 code contains significant
low frequency components which are not passed
through the isolation transformers and cannot be
restored by an adaptive equalizer. This leads to a
phenomenon known as Base-line Wander which will
cause an unacceptable increase in error rate if not
corrected. The NWK933 employs a quantized
feedback technique to restore the low frequency
components and thus maintain a very low error
rate even when receiving signals such as the
“killer packet” described in the TP_PMD spec.
4
The recovered clock is divided by 5 to generate the
receive clock (RX_CLK) which is used to strobe
received data across the MII interface. When no
signal is detected in 100BASE-TX mode, the PLL is
locked to the reference clock and runs at 125MHz.
This ensures that RX_CLK runs continuously at
25MHz in 100BASE-TX mode. When a signal is
present, the Clock Recovery PLL remains locked to
the reference until the equalizer has adjusted, then it
requires up to 1ms to phase lock to the incoming
signal. No data is passed to the MII interface until
lock is established.
RX100 SIPO, Decoder and Descrambler
The RX100 SIPO, Decoder and Descrambler convert
the received signal from serial MLT3 to 4-bit wide
parallel receive data on the MII. This appears on the
RXD[3:0] bus which is clocked out on the falling edge
of RX_CLK. When a frame starts the NWK933
decodes the SSD symbols and then asserts the
RX_DV signal, in order to inform the MAC that valid
data is available. When the NWK933 detects the
ESD, it deasserts the RX_DV signal.
RX100 Latency
The latency from the first bit of the “J” symbol on the
cable to CRS assertion is between 11 and 15BT. The
latency from the first bit of the “T” symbol on the
cable to CRS de-assertion is between 19 and 23BT.
100Mb/s Transmit Errors
If the NWK933 detects that the TX_ER signal has
gone active whilst the TX_EN signal is active, then it
will propagate the detected error onto the cable by
transmitting the symbol “00100” . Figure 3 shows the
meaning of the different states of TX_EN and TX_ER.
TX_ER is sampled inside the NWK933 on the rising
edge of TX_CLK.
NWK933
TX_EN TX_ER
TXD [3:0]
Indication
0
X
ignored
Normal inter frame data
1
0
0000 through 1111
Normal data transmission
1
1
0000 through 1111
Transmit error propagation
Figure 3. 100Mb/s Transmit Error States
100Mb/s Receive Errors
When there is no data on the cable, the receiver will
see only the idle code of scrambled 1’s. If a non idle
symbol is detected, the receiver looks for the SSD so
that it can align the incoming message for decoding.
If any 2 non consecutive zeros are detected within 10
bits, but are not the SSD symbols a false carrier
indication is signalled to the MII by asserting RX_ER
and setting RXD[3:0] to 1110 whilst keeping RX_DV
inactive. The remainder of the message is ignored
until 10 bits of 1’s are detected.
If any data is decoded after a SSD which is neither a
valid data code nor an ESD, then an error is flagged
by setting RX_ER active whilst the RX_DV signal is
active. This also happens if 2 idle codes are detected
before a valid ESD has been received or descramble
synchronisation is lost during packet reception. The
states of RX_DV and RX_ER are summarised in
Figure 4. RX_ER is clocked on the falling edge of
RX_CLK, and will remain active for at least 1 period
of RX_CLK.
RX_DV RX_ER
RXD [3:0]
Indication
Normal inter frame
Initialization (RESET_N)
The NWK933 incorporates a power-on-reset circuit
for self-initialization on power-up. During initialization
the open-drain RESET_N pin is driven low and all
data outputs are disabled to prevent spurious outputs
to the twisted-pair and to the MII interface. RESET_N
will remain low until the power supply has been stable
for at least 400ns. The NWK933 will then release
RESET_N allowing the external pull-up to pull the pin
high. Device initialisation will not commence until
RESET_N is high. This allows the user to extend the
inactive period by externally holding RESET_N low.
It will not normally be necessary for the user to reset
the NWK933 because it is designed to automatically
recover from fault conditions. However, if required,
the user may initialize the device by doing a hardware
or software reset.
Reset Mode
There are two types of reset in the NWK933 - hardware
and software. The hardware reset is activated by
setting the RESET_N pin to logic 0, and holding it low
for at least 100ns. This mode causes an over-all reset
in the NWK933 - both analog and digital circuitry are
reset. Whilst RESET_N is low, the SPDST and FDST
pins are inputs, and are used to determine the speed
and duplex capability which will be advertised during
auto-neg. A low on SPDST advertises 100M capability.
A high on FDST advertises full duplex capability.
The software reset is activated by setting bit 15 in
register 0 high. This bit is a self clear bit and causes
a partial reset of the device.
Figure 5 summarises the different blocks to be reset
and which reset will affect them:
0
0
0000 through 1111
0
1
1110
False carrier indication
HW Reset
SW reset
1
0
0000 through 1111
Normal data reception
management register
yes
yes
1
1
0101 or 0110
Data reception with errors
PCS state machine (RCV,
yes
yes
XMT scrambler
yes
yes
RCV scramble
yes
yes
control state machine
yes
No
analog
yes
No
Block
XMT, ANEG)
Figure 4. 100Mb/s receive error states
CONTROLS
Initialization, mode selection and other options are
governed by the control inputs and register as
described in the following paragraphs.
Figure 5. Effects of Reset
Note: Holding RESET_N low will hold the device in a static,
low power state.
5
NWK933
Low-Power Mode
This function is set via the management interface.
Using MDC and MDIO, Bit 11 of register 0 is written
high to put the NWK933 into Low-Power mode. The
type of low power mode is dependant on bits 14 and
15 in register 24.
For 24[15:14] = 0:0 the 10BASE-T and 100BASE-TX
transceivers are disabled. The oscillator continues
to run. Both RX_CLK and TX_CLK are stopped, the
RXD bus is held low and TXD, TXEN, and TXER are
ignored. MDC and MDIO are still active for new
commands. This mode is intended to conserve power
when the network connection is not required and the
TXOP/TXON output is undriven. Typical current
consumption is less than 10mA.
For 24[15:14] = 0:1, everything is turned off, including
the voltage references and the oscillator. This mode
must be exited via the management interface. Typical
current consumption is 0.5mA.
For 24[15:14] = 1:0, the only function available is the
signal detect. The NWK933 will detect a signal
amplitude on the cable and activate the interrupt.
MINT can be selected as either an active low or high
interrupt. Typical current consumption is less than
10mA.
For 24[15:14] = 1:1, the NWK933 will automatically
power down into a sleep mode if no activity is seen
on the cable for approx 2 seconds. Power up is also
automatic if activity is seen. Typical current
consumption is less than 10mA.
Loopback Mode
Diagnostic loopback may be selected at any time by
asserting setting Bit 14 in register 0. In 10BASE-T
mode transmission to the TXOP/ TXON output will
be stopped and the RX10 Clock Recovery will receive
input from the TX10 transmit path rather than from
the RXIP/RXIN inputs. In 100BASE-TX mode
transmission to the TXOP/TXON output will be stopped
and the RX100 Clock Recovery will receive input
from the TX100 transmit path.
Repeater Mode
The NWK933 can be put into Repeater Mode by
setting register 24 bit 0 high. In this mode, the CRS
will be active on receive only. In 100Mbps repeater
mode, the NWK933 is able to perform a disconnect
function from the MII. This function is enabled by bit
1 in register 24. (Note that if the device is not in
repeater mode, this bit has no effect). The NWK933
will disconnect from the MII if it receives two
6
consecutive false CRS events with no good frame in
between them or if a false CRS event is longer then
480 +/- 4BT. If the NWK933 receives a good carrier
event (480 +/- 4BT) or a good idle event (idle symbols
for a period of 25000 to 30000 bit time) it will resume
frame transfer to the MII.
A false CRS event happens if, at the beginning of a
carrier event, the JK symbols are not received
correctly.
When the NWK933 is in 100M mode it will count all
false CRS events in register 27 bits 7:0. This counter
is self cleared upon read. If a disconnect event
occurs between the consecutive reads of register 27,
bit 15 in the register will set high.
Auto-Negotiation Enable (ANEN)
Auto-negotiation may be hardware disabled by setting
the ANEN pin to logic zero. During operation, autonegotiation can be disabled by setting the ANEN pin
low or by setting bit 12 of register 0 to zero. If autoneg is disabled, the NWK933 will lose the link, and
link will be re-established only after the NWK933
control state machine has determined the speed
using bits 13 and 8 of register 0 to determine speed
and duplex respectively.
MII Management Interface, MDC and MDIO
The management interface is a 2 wire serial interface
connecting a PHY to a management entity. The
management unit controls the PHY and gathers
information on the status of the PHY. It does this via
the implemented registers using MDC to clock the
data on the MDIO pin.
Link Status Change Interrupt, MINT
MINT is, by default, an active low interrupt which is
activated whenever a change in the link status occurs.
It can be changed to be active high by setting bit 13
in register 24. The interrupt will remain active until
the controller acknowledges the interrupt by writing
to register 21 (any data). Should one or more link
status changes occur between the assertion of MINT
and an ackowledge, then MINT will be deasserted
and then reasserted (deassertion time between 100ns
and 150ns). Only a single interrupt event may be
queued at any one time. Multiple status changes
between an ackowledge will generate only a single
queued interrupt.
NWK933
TX10REF
TXD3-0
TX_ER
TX_EN
TX_CLK
FRAMING
&
CONTROL
TX10
PULSE
SHAPER
MANCHESTER
ENCODER
TX10
DRIVER
TX10
CLOCK
GEN.
RX10 FILTER
& SIGNAL
DETECT
FRAMING
&
CONTROL
RX10 CLOCK
& DATA
RECOVERY
LINK PULSE &
MANCHESTER
DECODE
CRS
RX100 &
SIGNAL
DETECT
COL
FRAMING
& 5B4B
DECODE
RXD3-0
RX_ER
RX_DV
RX_CLK
FRAMING
&4B5B
ENCODE
ALIGNER
&
DESCRAMBLE
RX100 CLOCK
& DATA
RECOVERY
RX100
EQUALIZER
& BLW
TX100 PISO
&
ENCODER
TX100
SCRAMBLER
TXOP
TXON
RXOP
RXON
TX100
DRIVER
TX100REF
TX100
CLOCK
GEN.
Internal
clock
LEDS
POWER
ON
RESET
ANEG
LOGIC
CONTROLS
MINT
ANEN
MDC
MDIO
PA4-0
RESET_N
XTAL2
XTAL1
OSC
REFCLK
ACTST
LNKST
COLST
FDST
SPDST
Figure 6 NWK933 block diagram
7
NWK933
Pin list
Pin #
Name
Type
Description
20
RXIN
Input
Differential receive pair from magnetics (-)
19
RXIP
Input
Differential receive pair from magnetics (+)
28
TXON
Output
100 Differential transmit pair to magnetics (-)
23
TXOP
Output
100 Differential transmit pair to magnetics (+)
35
TXREF10
Input
10BASE-T transmitter current setting pin
36
TXREF100
Input
100BASE-TX transmitter current setting pin
14
RESETN
IOput
Active low, power on reset output and external reset input
41
XTAL1
Input
25MHz crystal input
40
XTAL2
Input
25MHz crystal input
46
MDC
Input
Management interface clock (up to 2.5MHz)
45
MDIO
IOput
Management data
53
RX_CLK
Output
Receive clock (2.5MHz for 10, 25MHz for 100)
Output
Receive data MII interace
RX_DV
Output
Receive data valid. Active high.
59
RX_ER
Output
Receive error. Active high. (RXD4 in symbol mode)
43
REFCLK
Input
64
TX_CLK
Output
MD interface
MII interface
55, 56, 57, 58 RXD0, RXD1,
RXD2, RXD3
51
60, 61, 62, 63 TXD0, TXD1,
Reference clock
Transmit clock (2.5MHz for 10, 25MHz for 100)
Input
Transmit Data MII interface
TXD2, TXD3
4
TX_EN
Input
Transmit Enable. Active high.
2
TX_ER
Input
Transmit Error. Active high. (TXD4 in symbol mode)
50
CRS
Output
Carrier sense signal. Active high.
49
COL
Output
Collision signal. Active high.
22
ANEN
Input
48
MINT
Output
MII interrupt control.
6
ACTST
Output
Receive / transmit active indication (LED interface). Active low.
7
COLST
Output
Collision active indication (LED interface) Active low.
11
FDST
IOput
Full duplex indication when RESET_N high (LED interface). Active low. Input
Auto Negotiation enable. Active high.
when RESET_N is low. High input means 933 advertises full duplex capability.
12
5
LNKST
SPDST
IOput
Output
Link OK indication (LED interface). Active low.
Speed indication when RESET_N high (LED interface). High for 100Mb/s mode.
Input when RESET_N is low. Low input means 933 advertises 100Mb/s
capability.
31, 30, 29,
17, 13
8
PA0, PA1,
PA2, PA3, PA4
Input
Phy address
NWK933
General
The following is the register set that is implemented in the NWK933 device:
The interface to these registers is via the MDC and MDIO signals. The address of the NWK933 is specified by
the PA<4:0> static inputs The MD command is issued by the controller and can be read or write:
command preamble
start data
op code
phy address reg number
TA
Data
READ
32 bits of 1
01
10
5 bits
5 bits
Z0
16 bit from phy
WRITE
32 bits of 1
01
01
5 bits
5 bits
10
16 bit from MAC
SC = Self clear
RO = read only
RW = read or write
LL = latch low until register read
LH = latch high until register read
Register Set
reg 0 - control register
Bit
Bit name
0.15
Reset
0.14
Description
Default
R/W
1 = PHY reset
0 = Normal operation
0
RW
SC
Loopback
1 = Loopback mode active
0 = Normal operation
0
RW
0.13
Speed
selection
1 = 100 Mbps
0 = 10 Mbps
1
RW
0.12
ANEG
enable
1 = Enable ANEG process
0 = Disable ANEG process
1
RW
0.11
Power down
1 = Power down active
0 = Normal operation
0
RW
0.10
Isolation
1 = isolation in process
0 = Normal operation
0
RW
0.9
Restart
ANEG
1 = Restart the ANEG process
0 = Normal operation
0
RW
SC
0.8
Duplex
selection
1= Full Duplex mode
0 = Half duplex mode
1
RW
0.7
Collision
test
1 = Collision test active
0 = Normal operation
0
RW
0.6:0
Reserved
Write as 0 ignore on read.
9
NWK933
reg 1- status register
Bit
Bit name
1.15
100BaseT4
1.14
Description
Default
R/W
1 = PHY able to perform 100BaseT4
0 = PHY not able to perform 100BaseT4
0
RO
100BASE-TX
- FDX
1 = PHY able to perform 100BASE-TX
0 = PHY not able to perform 100BASE-TX
1
RO
1.13
100BASE-TX
- HDX
1 = PHY able to perform 100BASE-TX
0 = PHY not able to perform 100BASE-TX
1
RO
1.12
10BASE-T
- FDX
1 = PHY able to perform 10BASE-T
0 = PHY not able to perform 10BASE-T
1
RO
1.11
10BASE-T
- HDX
1 = PHY able to perform 10BASE-T
0 = PHY not able to perform 10BASE-T
1
RO
1.10
100BaseT2
- FDX
1 = PHY able to perform 100BaseT2
0 = PHY not able to perform 100BaseT2
0
RO
1.9
100BaseT2
- HDX
1 = PHY able to perform 100BaseT2
0 = PHY not able to perform 100BaseT2
0
RO
1.8:7
Reserved
ignore when read
0
RO
1.6
MF preamble
suppression
1= Phy accept management frames with short preamble
0 = normal preamble only
0
RO
1.5
ANEG
complete
1 = ANEG process completed
0 = ANEG process not completed or not active
0
RO
1.4
Remote
fault
1= Remote fault condition detected
0 = no Remote fault condition detected
0
RO
LH
1.3
ANEG able
1 = Phy is able to perform ANEG
0 = Phy is not able to perform ANEG
1
RO
1.2
Link status
1= Link is up
0 = Link is down
0
RO
LL
1.1
Jabber
detect
1 = jabber condition detected
0 = normal operation
0
RO
1.0
Extended
regs
1 = extended register capability
0 = no extended registers
1
RO
reg 2/3- NWK933 Identifier register
10
Bit
Bit name
Description
Default
R/W
2.15:0
OUI
Mitel OUI bits
0282
RO
3.15:0
OUI/device ID
Mitel OUI bits and device code
1C7X
RO
NWK933
reg 4- ANEG advertisement register
Bit
Bit name
4.15
NP
4.14
reserved
4.13
remote fault
4.12:10
reserved
4.9:5
Technology
4.4:0
selector
field
Description
Default
R/W
0
RO
0
RO
0
R/W
0
R/W
0F
R/W
01
R/W
Default
R/W
partner is next page capable
0
RO
Next page able - the NWK933 is not able to
perform next page
0 = no remote fault detected
1= a remote fault been detected
T4, 100Fdx, 100Hdx, 10Fdx, 10Hdx
reg 5- ANEG link partner ability register
Bit
Bit name
Description
5.15
NP
5.14
ACK
partner sent an acknowledge bit
0
RO
5.13
remote fault
partner detected a remote fault
0
RO
5.12:5
ability
partner’s technology ability
0
RO
5.4:0
selector field
partner selector field
0
RO
Default
R/W
0
RO
0 = aneg process finished. No fault detected
1 = a fault has been detected
0
RO
LH
reg 6- ANEG expansion register
Bit
Bit name
6.15:5
reserved
6.4
parallel
detect fault
6. 3
link partner
next page able
0 = Link partner is not next page able
1 = Link partner is next page able
0
RO
6.2
next page
able
Page
received
0 = NWK933 is not able for next page
0
RO
0 = no new page been received
1= a new page has been received and is in reg 5
0
RO
LH
link partner
aneg able
0 = Link partner is not aneg able
1 = Link partner is aneg able
0
RO
Default
R/W
0000
res
6.1
6.0
Description
reg 16, 17, 18, 19, 20 - Test registers
Bit
Bit name
Description
15:0
reserved
test mode only
11
NWK933
reg 21 - MII interrupt control register
Bit
Bit name
21.15:0
Clear Interrupt
Description
Default
R/W
0
WO
Default
R/W
0000
res
Write any data pattern to clear MINT
reg 22, 23 - Test registers
Bit
Bit name
Description
15:0
reserved
test mode only
reg 24- NWK933 specific register
12
Bit
Bit name
24.15:14
PWRCON[1:0]
24.13
MINTPOL
24.12
Pol Dis
24.11
Description
Default
R/W
Low power controls:
00 = full receive path active. No transmit.
01 = Deep sleep (all off including VREF & OSC)
10 = Sleep (generate MII interrupt on activity)
11 = auto shut down, auto wake on activity
00
RW
1 = MINT output active high
0 = MINT output active low
0
RW
1 = disable 10Base-T autopolarity correction
0
RW
SQE disable
1 = disable SQE in 10Base-T half duplex mode
0
RW
24.10
JAB disable
0 = in case of jabber the 10Base-T will cut the
transmitted frame (normal operation)
1 = Jabber function disable
0
RW
24. 9
loop 10
1 = enable MII loopback in 10Base-T half duplex mode
0
RW
24.8
Force RX
Force receive regardless of link
0
RW
24.7
Force TX
Force transmit regardless of link
0
RW
24.6
CRS_CTL
CRS behavior in full duplex mode:0 = CRS is active for transmit only
1= CRS active for receive or transmit
0
RW
24.5
MF
1 = MDIO data accepted without preamble
0
RW
24.4
Byp ALIGN
0 = normal operation
1 = bypass the aligner function
0
RW
24.3
Byp ENC
0 = normal operation
1 = bypass the 4B5B encoder function
0
RW
24.2
Byp SCR
0 = normal operation
1 = bypass the scrambler function
0
RW
24.1
DISCEN
0
RW
24:0
RPTR
0 = disable disconnection events
1 = enable disconnect on false carrier detection
Set repeater mode (affects CRS generation)
0
RW
NWK933
reg 25 - ANEG status
Bit
Bit name
Description
Default
R/W
25.15:14
reserved
test mode only - do not set high
0
RO
25.13
Pol
1 indicates polarity reversal on RX inputs (10Base-T)
0
RO
25.12:8
PA
copy of PHY address pins
PA<4:0>
RO
25.7
aneg
complete
1 = aneg completed
0 = aneg did not complete (same as reg1.5)
0
RO
25.6
Duplex
ANEG result - duplex operation
0 = HDX, 1 = FDX
0
RO
25.5
speed
ANEG result - speed of operation
0 = 10M, 1 = 100M
0
RO
25.4
ability mtc
1 = abilities match between registers 4 & 5
0
RO
25.3:0
ANEG state
ANEG state machine current state
0
RO
Default
R/W
0
RO
SC
Default
R/W
0
RO
LH
0
RO
0
RO
SC
Default
R/W
0000
res
reg 26 - Symbol error counter
Bit
Bit name
Description
26.15:0
RX_ERR
counter
number of RX_ERR events since last read - Clears
either in change of speed or read of this reg.
reg 27 - False carrier event counter
Bit
Bit name
Description
27.15
disconnect
the disconnect mechanism status
27.14:8
reserved
27.7:0
false CRS
counter
number of False CRS events since last read.
Active only when DISCEN = 1”.
reg 28, 29, 30, 31 - Test registers
Bit
Bit name
Description
15:0
reserved
test mode only
13
NWK933
Operating Conditions
Supply voltage
Ambient temperature
+3.0V to 3.6V
0°C to +70°C
DC Electrical Characteristics
Recommended operating conditions apply except where stated.
Characteristic
Symbol
Value
Units
Min
Max
VIH
VIL
IIH
IIL
2
VSS
-
VDD
0.8
1
–1
8
V
V
µA
µA
pF
VOH
VOL
IOH
IOL
2.4
VSS
-
VDD
0.4
–6
6
4
4
8
V
V
mA
mA
nS
nS
pF
2.2
0.95
-0.05
-1.05
2.8
1.05
0.05
-0.95
V
V
V
V
Conditions
DC parameters - input
High level input voltage
Low level input voltage
High level input current
Low level input current
Pin capacitance to ground
no pull up
including package
DC parameters - output -6mA buffers
High level output voltage
Low level output voltage
High level output current
Low level output current
Rise time
Fall time
Pin capacitance to ground
0.4V to 2.4V into 20pF load
0.4V to 2.4V into 20pF load
Differential Output
Peak Differential Voltage
High Level
Zero Level
low Level
10Mbs mode
100Mbs mode
100Mbs mode
100Mbs mode
Note: Differential outputs are 802.3 compliant
AC Electrical Characteristics
Recommended operating conditions apply except where stated.
Characteristic
Symbol
Value
Units
Min
Max
3
3
3
3
5
5
5
5
Conditions
Differential Output
Baseline to +Vout
Baseline to -Vout
+Vout to Baseline
-Vout to Baseline
Note: Differential outputs are 802.3 compliant
14
nS
nS
nS
nS
100Mbs mode
100Mbs mode
100Mbs mode
100Mbs mode
NWK933
AC Electrical Characteristics (continued)
Recommended operating conditions apply except where stated.
Characteristic
Symbol
Value
Min
Units
Conditions
Max
REFCLK
Frequency
Duty cycle
25±100ppm
45
55
MHz
%
25±100ppm
40
60
2.5±100ppm
40
60
MHz
%
MHz
%
100Mbs mode
100Mbs mode
10Mbs mode
10Mbs mode
25±100ppm
40
60
2.5±100ppm
40
60
MHz
%
MHz
%
100Mbs mode
100Mbs mode
10Mbs mode
10Mbs mode
160
2.5
-
MHz
ns
Typ
Max
80
180
128
133
5
0.25
1
90
200
145
150
6
1
2
RXCLK
Frequency
Duty cycle
Frequency
Duty cycle
TXCLK
Frequency
Duty cycle
Frequency
Duty cycle
MDC
Frequency
Minimum high/low
Supply Current
10 Base-T Idle
10 Base-T Active
100 Base-T Idle
100 BAse-T Active
Sleep Mode
Deep sleep mode
Resetn = 0
mA
mA
mA
mA
mA
mA
mA
Measured at 3.3V
Room Temperature
These Figures include
the current flowing
in the Transmit resistors
15
TXD3
TXD2
TXD1
TXD0
RX_ER
RXD3
RXD2
RXD1
RXD0
DVDD2
RX_CLK
DGND2
RX_DV
CRS
COL
TX_CLK
NWK933
MINT
SUBGND2
TX_ER
DGND1
TX_EN
LNKST
ACTST
COLST
Vdd
Vdd
Vdd
DVDD1
RXVDD3
RXGND3
FDST
SPDST
TXVDD3
TXGND3
30 (1%) 30 (1%)
PA2
PA1
PA0
SUBGND1
RXVDD2
RXGND2
PA3
RXGND1
RXIP
RXIN
5K(5%)
PA4
RESETN
TXVDD2
TXGND2
TXGND1
TXVDD1
TXON
10K(5%)
Vdd
OSCGND
TXCGND4
TXVDD4
TXREF100
TXREF10
RXVDD1
ANEN
TXOP
Vdd
Vdd
DVDD3
MDC
MDIO
DGND3
RefCLK
OSCVDD
XTAL1
XTAL2
C2
C2
1.24K
1%
24.9 (1%)
24.9 (1%)
10
0.01µF
20 (1%) 20 (1%)
TXIC
TXIN
0.01µF
RXON
TXIP
RXOP
1.24K
1%
25MHz
1:√2 MAGNETICS
Figure 7 External Components
EXTERNAL COMPONENTS
Crystal Oscillator
Connecting an External 25MHz Reference
For IEEE802.3 compliance the oscillator must run at
25MHz ±100ppm. The NWK933 on-chip circuitry
contributes less than 40ppm variability to the oscillator
frequency, therefore the crystal must be specified to
60ppm. This must include variations due to
temperature and ageing. The crystal must be capable
of dissipating 0.5mW of power.
If an external clock is used then it should be driven
into the REFCLK input, and XTAL1 must be connected
to ground. XTAL2 must be left unconnected. If a
crystal is used, REFCLK must be connected to ground.
RESETN Pull-up Resistor
This resistor is required regardless of whether or not
RESETN is used externally.
RX Input Decoupling
The method of using a split input load resistor and
de-coupling the centre tap reduces common mode
noise.
16
External capacitors are required on the XTAL1 &
XTAL2 pins. Manufacturer's recommendations should
be followed.
Tracking to the crystal and the capacitors must be as
short as possible. Other signal paths must not cross
the area.
The NWK933 is supported by the following magnetics:
VENDOR
Pulse
MAGNETICS
H1119
http://www.mitelsemi.com
World Headquarters - Canada
Tel: +1 (613) 592 2122
Fax: +1 (613) 592 6909
North America
Tel: +1 (770) 486 0194
Fax: +1 (770) 631 8213
Asia/Pacific
Tel: +65 333 6193
Fax: +65 333 6192
Europe, Middle East,
and Africa (EMEA)
Tel: +44 (0) 1793 518528
Fax: +44 (0) 1793 518581
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.
This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s
conditions of sale which are available on request.
M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation
Mitel Semiconductor is an ISO 9001 Registered Company
Copyright 1999 MITEL Corporation
All Rights Reserved
Printed in CANADA
TECHNICAL DOCUMENTATION - NOT FOR RESALE