SP8902 (MP) 5GHZ 4 42 Fixed Modulus Divider Preliminary Information DS4375 Issue 1.4 September 1999 The SP8902 is one of a range of very high speed low power prescalers for professional applications. The dividing elements are static D type flip flops and therefore allow operation down to DC if the drive signal is a pulse waveform with fast risetime. The output stage has a differential current output and provides a direct drive into a 50 ohm load. Ordering Information SP8902/KG/MP1S (tubes) SP8902/KG/MP1T (tape and reel) Features Absolute Maximum Ratings ● Very High Operating Speed ● Operation down to DC with Square Wave Input ● Silicon Technology for Low Phase Noise Supply voltage, VCC 6·5V Storage temperature 265°C to 1150°C Maximum junction temperature 1150°C Prescaler input voltage 2·5Vp-p Operating temperature KG240°C to 185°C TCASE (Typically better than 2140dBc/Hz at 1KHz) ● 5V Single Supply Operation ● Low Power Dissipation: 335mW (Typ.) ● Surface Mount Plastic Package OUTPUT VCC VCC 1 8 7 6 VREF 42 400 INPUT INPUT 400 2 10mA 3 4 4 GND Figure 1 block diagram OUTPUT OUTPUT SP8902 VCC 1 INPUT 2 INPUT GND 8 OUTPUT VCC 7 OUTPUT 3 6 OUTPUT 4 5 GND SP8902 MP8 Figure 2 Pin connections - top view Electrical Characteristics These characteristics are guaranteed by either production test or design over the following range of operating conditions unless otherwise stated: TAMB = 240°C to 185°C, VCC = 4·75V to 5·25V Value Characteristic Pin 1, 8 2, 3 2, 3 2, 3 2, 3 2, 3 6, 7 6, 7 Supply current Input frequency Input sensitivity Input sensitivity Input overload Input overload Output voltage Output power Min. Typ. Max. 1·0 440 700 215·0 67 0·5 112 92 5·0 180 570 12·0 Units Conditions mA GHz mVrms mVrms mVrms mVrms Vp-p dBm RMS sinewave fIN = 1GHz and 4.2GHz fIN = 5GHz fIN = 1GHz and 3GHz fIN = 5.0GHz and 3.8GHz Into 50Ω pullup resistor fIN = 1GHz and 5GHz (see note 1 ) NOTE 1. Measured into 50Ω measuring instrument in parallel with 50Ω pullup resistor. See Figure 5. VIN INTO 50Ω (mV RMS) 800 600 TESTED AS PER TABLE OF ELECTRICAL CHARACTERISTICS 400 OPERATING WINDOW 200 1 2 3 4 5 FREQUENCY (GHz) Figure3 Typical input sensitiviy (sinewave drive) 2 6 7 SP8902 VCC 15V 1 8 2 7 1n SIGNAL GENERATOR SP8902 3 6 4 5 50 50 1n 50Ω MEASURING INSTRUMENT 1n 10n 1n 10n Figure 4 Typical application and test circuit j1 j0.5 j2 3GHz j0.2 5GHz 0 0.2 0.5 1 2 j5 5 0·3GHz 1GHz 2j5 2j0.2 2j2 2j0.5 2j1 Figure 5 Typical input impedance 3 4 Figure 6 Typical phase noise, input frequency = 3GHz 10 2 170 2 160 2 150 2 140 2 130 2 120 2 110 2 100 2 90 2 80 2 70 2 60 2 50 2 40 2 30 2 20 2 10 0 100 1k FREQUENCY (Hz) 10k 100k SP8902 L(f) [dBc/Hz] http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE