MOSEL VITELIC V437432E24V 3.3 VOLT 32M x 72 HIGH PERFORMANCE REGISTERED SDRAM ECC MODULE PRELIMINARY Features Description ■ 168 Pin Registered ECC 33,554,432 x 72 bit Oganization SDRAM Modules ■ Utilizes High Performance 32M x 8 SDRAM in TSOPII-54 Packages ■ Fully PC Board Layout Compatible to INTEL’S Rev 1.0 Module Specification ■ Single +3.3V (± 0.3V) Power Supply ■ Programmable CAS Latency, Burst Length, and Wrap Sequence (Sequential & Interleave) ■ Auto Refresh (CBR) and Self Refresh ■ All Inputs, Outputs are LVTTL Compatible ■ 8192 Refresh Cycles every 64 ms ■ Serial Presence Detect (SPD) The V437432E24V memory module is organized 33,554,432 x 72 bits in a 168 pin dual in line memory module (DIMM). The 32M x 72 registered DIMM uses 9 Mosel-Vitelic 32M x 8 ECC SDRAM. The x72 modules are ideal for use in high performance computer systems where increased memory density and fast access times are required. Part Number Speed Grade Configuration V437432E24VXTG-75PC -75PC, CL=2,3 (133 MHz) 32M x 72 V437432E24VXTG-75 -75, CL=3 (133 MHz) 32M x 72 V437432E24VXTG-10PC -10PC, CL=2,3 (100 MHz) 32M x 72 V437432E24V Rev. 1.0 January 2002 1 MOSEL VITELIC V437432E24V Pin Configurations (Front Side/Back Side) Pin Front Pin Front Pin Front Pin Back Pin Back Pin Back 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VSS I/O1 I/O2 I/O3 I/O4 VCC I/O5 I/O6 I/O7 I/O8 I/O9 VSS I/O10 I/O11 I/O12 I/O13 I/O14 VCC I/O15 I/O16 CBO* CB1* VSS NC NC VCC WE DQM0 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 DQM1 CS0 DU VSS A0 A2 A4 A6 A8 A10(AP) BA1 VCC VCC CLK0 VSS DU CS2 DQM2 DQM3 DU VCC NC NC CB2* CB3* VSS I/O17 I/O18 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 I/O19 I/O20 VCC I/O21 NC DU CKE1 VSS I/O22 I/O23 I/O24 VSS I/O25 I/O26 I/O27 I/O28 VCC I/O29 I/O30 I/O31 I/O32 VSS CLK2 NC WP SDA SCL VCC 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 VSS I/O33 I/O34 I/O35 I/O36 VCC I/O37 I/O38 I/O39 I/O40 I/O41 VSS I/O42 I/O43 I/O44 I/O45 I/O46 VCC I/O47 I/O48 CB4* CB5* VSS NC NC VCC CAS DQM4 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 DQM5 CS1 RAS VSS A1 A3 A5 A7 A9 BA0 A11 VCC CLK1 A12 VSS CKE0 CS3 DQM6 DQM7 DU VCC NC NC CB6* CB7* VSS I/O49 I/O50 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 I/O51 I/O52 VCC I/O53 NC DU NC VSS I/O54 I/O55 I/O56 VSS I/O57 I/O58 I/O59 I/O60 VCC I/O61 I/O62 I/O63 I/O64 VSS CLK3 NC SA0 SA1 SA2 VCC Notes: Pin Names A0–A12 Address Inputs I/O1–I/O64 Data Inputs/Outputs RAS Row Address Strobe CAS Column Address Strobe WE BA0, BA1 SDA Serial Data OUT for Presence Detect SA0–A2 Serial Data IN for Presence Detect Read/Write Input CB0–CB7 Check Bits (x72 Organization) Bank Selects NC No Connection CKE0, CKE1 Clock Enable DU Don’t Use CS0–CS3 Chip Select CLK0–CLK3 Clock Input DQM0–DQM7 Data Mask VCC Power (+3.3 Volts) VSS Ground SCL Clock for Presence Detect V437432E24V Rev. 1.0 January 2002 2 MOSEL VITELIC V437432E24V Module Part Number Information V 4 3 74 32 E 2 4 V X SDRAM 3.3V G - XX COMPONENT PACKAGE, T = TSOP WIDTH DEPTH COMPONENT A=0.17u, B=0.14u REV LEVEL 168 PIN Registered DIMM X8 COMPONENT LVTTL REFRESH RATE 8K V437432E24V Rev. 1.0 January 2002 T SPEED 75PC = PC133 CL3,2 75 = PC133 CL3 10PC = PC100 CL3,2 LEAD FINISH G = GOLD MOSEL VITELIC MANUFACTURED 3 4 BANKS MOSEL VITELIC V437432E24V Block Diagram RWE RCS0R CS DQM WE I/O1–I/O8 RDQM0 I/O1–I/O8 D0 RDQM4 I/O40–I/O33 10 CS D1 RDQM5 I/O48–I/O41 10 BC0–7 CS DQM WE I/O1–I/O8 CS WE DQM I/O1–I/O8 CS WE DQM I/O1–I/O8 CS D4 10 DQM WE I/O1–I/O8 DQM1 I/O9–I/O16 DQM WE I/O1–I/O8 D5 10 DQM WE I/O1–I/O8 CS WE DQM I/O1–I/O8 CS 10 RCS2 RDQM2 I/O17–I/O24 D2 RDQM6 I/O49–I/O56 10 CS WE DQM I/O1–I/O8 RDQM3 I/O25–I/O32 D6 10 D3 RDQM7 I/O57–I/O64 10 D0-D7, Reg DLL VCC E2PROM SPD (256 WORD X 8 BITS) C0-C17 VSS SCL0 SA2 SA1 SA0 D7 10 D0-D7, Reg DLL SDA CLK0 PLL SDRAMD–D8 12 pF WP 47K CS0–CS2 RCS0–RCS2 DQM0–7 A0–A12 RAS CAS CKEO WE VCC REGE V437432E24V Rev. 1.0 January 2002 4 REGISTER BA0, BA1 RDQM0–7 RBA0–RBA1 RA0–RA12 SDRAMD0–8 SDRAMD0–8 RRAS SDRAMD0–8 RCAS SDRAMD0–8 RCKE0 RWE SDRAMD0–8 SDRAMD0–8 10K CLK1, CLK2, CLK3 12 pF MOSEL VITELIC V437432E24V Serial Presence Detect Information written into the E2PROM device during module production using a serial presence detect protocol (I 2C synchronous 2-wire bus) A serial presence detect storage device – – is assembled onto the module. Information about the module configuration, speed, etc. is E2PROM SPD-Table for modules: Byte Number Hex Value Function Described SPD Entry Value -75PC -75 -10PC 0 Number of SPD bytes 128 80 80 80 1 Total bytes in Serial PD 256 08 08 08 2 Memory Type SDRAM 04 04 04 3 Number of Row Addresses (without BS bits) 13 0D 0D 0D 4 Number of Column Addresses (for x8 SDRAM) 10 0A 0A 0A 5 Number of DIMM Banks 1 01 01 01 6 Module Data Width 72 48 48 48 7 Module Data Width (continued) 0 00 00 00 8 Module Interface Levels LVTTL 01 01 01 9 SDRAM Cycle Time at CL=3 7.5 ns/10.0 ns 75 75 A0 10 SDRAM Access Time from Clock at CL=3 5.4 ns/6.0 ns 54 54 60 11 Dimm Config (Error Det/Corr.) ECC 02 02 02 12 Refresh Rate/Type Self-Refresh, 7.8µs 82 82 82 13 SDRAM width, Primary x8 08 08 08 14 Error Checking SDRAM Data Width n/a / x8 08 08 08 15 Minimum Clock Delay from Back to Back Random Column Address tccd = 1 CLK 01 01 01 16 Burst Length Supported 1, 2, 4, 8 0F 0F 0F 17 Number of SDRAM Banks 4 04 04 04 18 Supported CAS Latencies CL = 2,3 06 06 06 19 CS Latencies CS Latency = 0 01 01 01 20 WE Latencies WL = 0 01 01 01 21 SDRAM DIMM Module Attributes Registered/Buffered. 1F 1F 1F 22 SDRAM Device Attributes: General Vcc tol ± 10% 0E 0E 0E 23 Minimum Clock Cycle Time at CAS Latency =2 7.5 ns /10.0 ns 75 A0 A0 24 Maximum Data Access Time from Clock for CL = 2 5.4 ns/6.0 ns 54 60 60 25 Minimum Clock Cycle Time at CL = 1 Not Supported 00 00 00 26 Maximum Data Access Time from Clock at CL = 1 Not Supported 00 00 00 27 Minimum Row Precharge Time 15 ns/20 ns 0F 14 14 V437432E24V Rev. 1.0 January 2002 5 MOSEL VITELIC V437432E24V SPD-Table for modules: (Continued) Byte Number Hex Value Function Described SPD Entry Value -75PC -75 -10PC 14 ns/15 ns/16 ns 0E 0F 10 28 Minimum Row Active to Row Active Delay tRRD 29 Minimum RAS to CAS Delay tRCD 15 ns/20 ns 0F 14 14 30 Minimum RAS Pulse Width tRAS 42 ns/45 ns 2A 2D 2D 31 Module Bank Density (Per Bank) 256 MByte 40 40 40 32 SDRAM Input Setup Time 1.5 ns/2.0 ns 15 15 20 33 SDRAM Input Hold Time 0.8 ns/1.0 ns 08 08 10 34 SDRAM Data Input Setup Time 1.5 ns/2.0 ns 15 15 20 35 SDRAM Data Input Hold Time 0.8 ns/1.0 ns 08 08 10 00 00 00 02 02 12 2E 73 E1 40 40 40 00 00 00 36-61 Superset Information (May be used in Future) 62 SPD Revision 63 Checksum for Bytes 0 - 62 64 Manufacturer’s JEDEC ID Code 65-71 72 Revision 2/1.2 Mosel Vitelic Manufacturer’s JEDEC ID Code (cont.) Manufacturing Location 73-90 Module Part Number (ASCII) 91-92 PCB Identification Code 93 Assembly Manufacturing Date (Year) 94 Assembly Manufacturing Date (Week) V437432E24V 95-98 Assembly Serial Number 99-125 Reserved 00 00 00 126 Intel Specification for Frequency 64 64 64 127 Reserved 00 00 00 128+ Unused Storage Location V437432E24V Rev. 1.0 January 2002 6 MOSEL VITELIC V437432E24V DC Characteristics TA = 0°C to 70°C; VSS = 0 V; VDD, VDDQ = 3.3V ± 0.3V Limit Values Symbol Parameter Min. Max. Unit VIH Input High Voltage 2.0 VCC +0.3 V V IL Input Low Voltage –0.5 0.8 V V OH Output High Voltage (IOUT = –4.0 mA) 2.4 — V V OL Output Low Voltage (IOUT = 4.0 mA) — 0.4 V II(L) Input Leakage Current, any input (0 V < VIN < 3.6 V, all other inputs = 0V) –10 10 µA IO(L) Output leakage current (DQ is disabled, 0V < VOUT < V CC) –10 10 µA Capacitance TA = 0°C to 70°C; VDD = 3.3V ± 0.3V, f = 1 MHz Symbol Parameter Limit Values Unit CI1 Input Capacitance (A0 to A11, RAS, CAS, WE) 85 pF CI2 Input Capacitance (CS0-CS3) 30 pF CICL Input Capacitance (CLK0-CLK3) 22 pF CI3 Input Capacitance (CKE0, CKE1) 50 pF CI4 Input Capacitance (DQM0-DQM7) 20 pF CIO Input/Output Capacitance (I/O1-I/064) 20 pF CSC Input Capacitance (SCL, SA0-2) 8 pF CSD Input/Output Capacitance 18 pF V437432E24V Rev. 1.0 January 2002 7 MOSEL VITELIC V437432E24V Absolute Maximum Ratings Parameter Max. Units Voltage on VDD Supply Relative to V SS -1 to 4.6 V Voltage on Input Relative to VSS -1 to 4.6 V Operating Temperature 0 to +70 °C -55 to 125 °C 7.2 W Storage Temperature Power Dissipation Standby and Refresh Currents1 TA = 0°C to 70°C, VCC = 3.3V ± 0.3V Symbol Parameter Test Conditions -75PC/75 -10PC Unit Note ICC1 Operating Current Burst length = 4, CL = 3 tRC> = tRC(min), tCK> = tCK(min), IO = 0 mA 2 Bank Interleave Operation 2070 1890 mA 1,2 ICC2P Precharged Standby Current in Power Down Mode CKE< = VIL(max), tCK> = tCK(min) 18 18 mA ICC2N Precharged Standby Current in Non-Power Down Mode CKE> = VIH (min), tCK> = tCK(min), Input changed once in 3 cycles 360 315 mA ICC3P Active Standby Current in Power Down Mode CKE< = VIL(max), tCK> = tCK(min) 90 90 mA ICC3N Active Standby Current in Non-Pow- CKE> = VIH (min), tCK> = tCK(min), Iner put changed one time Down Mode 450 405 mA CS = High ICC4 Burst Operating Current tRC = Infinite, CL = 3, tCK> = tCK(min), IO = 0 mA 2 Banks Activated 1350 1080 mA 1, 2 ICC5 Auto Refresh Current tRC>= tRC(min) 2160 1980 mA 1,2 ICC6 Self Refresh Current CKE = <0.2 V Standard 27 27 mA 1,2 L-version 15.3 15.3 V437432E24V Rev. 1.0 January 2002 8 CS = High MOSEL VITELIC V437432E24V AC Characteristics 3,4 TA = 0° to 70°C; VSS = 0V; VCC = 3.3V ± 0.3V, tT = 1 ns Limit Values -75PC # Symbol Parameter Min. -75 Max. Min. -10PC Max. Min. Max. Unit Note Clock and Clock Enable 1 2 3 tCK fCK tAC Clock Cycle Time CAS Latency = 3 CAS Latency = 2 7.5 7.5 System frequency CAS Latency = 3 CAS Latency = 2 – – 133 133 – – 133 100 – – 100 100 MHz MHz Clock Access Time CAS Latency = 3 CAS Latency = 2 – – 5.4 6 – – 5.4 6 – – 6 6 ns ns 7.5 10 10 10 ns ns 4,5 4 tCH Clock High Pulse Width 2.5 – 2.5 – 3 – ns 6 5 tCL Clock Low Pulse Width 2.5 – 2.5 – 3 – ns 6 6 tCS Input Setup time 1.5 – 1.5 – 2 – ns 7 7 tCH Input Hold Time 0.8 – 0.8 – 1 – ns 7 8 tCKSP CKE Setup Time (Power down mode) 2.5 – 2 – 2 – ns 8 9 tCKSR CKE Setup Time (Self Refresh Exit) 8 – 8 – 8 – ns 9 10 tT Transition time (rise and fall) 1 – 1 – 1 – ns RAS to CAS delay 15 – 20 – 20 – ns Common Parameters 11 tRCD 12 tRC Cycle Time 60 120k 70 120k 70 120k ns 13 tRAS Active Command Period 42 – 45 – 45 – ns 14 tRP Precharge Time 20 – 20 – 20 – ns 15 tRRD Bank to Bank Delay Time 16 – 15 – 20 – ns 16 tCCD CAS to CAS delay time (same bank) 1 – 1 – 1 – CLK Refresh Cycle 17 tSREX Self Refresh Exit Time 10 – 10 – 10 – ns 9 18 tREF Refresh Period (8192 cycles) 64 – 64 – 64 – ms 8 4 Read Cycle 19 tOH Data Out Hold Time 3 – 3 – 3 – ns 20 tLZ Data Out to Low Impedance Time 0 – 0 – 0 – ns 21 tHZ Data Out to High Impedance Time 3 7.5 3 7.5 3 8 ns 22 tDQZ DQM Data Out Disable Latency 2 – 2 – 2 – CLK 10 Write Cycle 23 tDPL Data input to Precharge (write recovery) 2 – 2 – 1 – CLK 24 tDAL Data In to Active/refresh 5 – 5 – 5 – CLK 25 tDQW DQM Write Mask Latency 0 – 0 – 0 – CLK V437432E24V Rev. 1.0 January 2002 9 11 MOSEL VITELIC V437432E24V Notes: 1. The specified values are valid when addresses are changed no more than once during t CK(min.) and when No Operation commands are registered on every rising clock edge during t RC(min). Values are shown per module bank. 2. The specified values are valid when data inputs (DQ’s) are stable during t RC(min.). 3. All AC characteristics are shown for device level. An initial pause of 100 µs is required after power-up, then a Precharge All Banks command must be given followed by 8 Auto Refresh (CBR) cycles before the Mode Register Set Operation can begin. 4. AC timing tests have VIL = 0.4V and V IH = 2.4V with the timing referenced to the 1.4V crossover point. The transition time is measured between VIH and VIL. All AC measurements assume tT = 1 ns with the AC output load circuit shown. Specific tac and toh parameters are measured with a 50 pF only, without any resistive termination and with a input signal of 1V / ns edge rate between 0.8V and 2.0V. + 1.4 V tCH 2.4V CLOCK 50 Ohm 0.4V tCL tSETUP Z=50 Ohm tT I/O tHOLD 50 pF 1.4V INPUT tAC tAC tLZ I/O tOH 50 pF 1.4V OUTPUT Measurement conditions for tac and toh tHZ 5. If clock rising time is longer than 1 ns, a time (tT/2 -0.5) ns has to be added to this parameter. 6. Rated at 1.5V 7. If tT is longer than 1 ns, a time (tT -1) ns has to be added to this parameter. 8. Any time that the refresh Period has been exceeded, a minimum of two Auto (CBR) Refresh commands must be given to “wake-up” the device. 9. Self Refresh Exit is a synchronous operation and begins on the 2nd positive clock edge after CKE returns high. Self Refresh Exit is not complete until a time period equal to tRC is satisfied once the Self Refresh Exit command is registered. 10. Referenced to the time which the output achieves the open circuit condition, not to output voltage levels. 11. tDAL is equivalent to t DPL + tRP. V437432E24V Rev. 1.0 January 2002 10 MOSEL VITELIC V437432E24V Package Dimensions All measurements in mm 133.37 127.35 17.80 43.15 (2.63) 10 11 40 41 84 3.0 1 42.18 1.27 ± 0.100 63.68 A 94 95 124 125 168 4.0 85 B D 6.35 1.0 ± 0.05 1.27 2.50 3.125 3.125 6.35 0.2 ± 0.15 2.0 2.0 3.175 Detail A 4.45 Detail B 2.26 RADIUS 1.27 + 0.10 Tolerances: ± (0.13) unless otherwise specified. V437432E24V Rev. 1.0 January 2002 11 Detail C MOSEL VITELIC V437432E24V Label Information Module Density MOSEL VITELIC Part Number Criteria of PC100 or PC133 (refer to MVI datasheet) DIMM manufacture date code V437432E24VXXX-XX 256MB CLX PC133R-XXX-542-A XXXX-XXXXXXX Assembly in Taiwan PC133 R -XXX REGISTERED DIMM A Gerber file Intel PC100 x8 Based CL= 3 or 2 (CLK) tRCD= 3 or 2 (CLK) tRP= 3 or 2 (CLK) V437432E24V Rev. 1.0 January 2002 54 2 CAS Latency 2=CL2 3=CL3 JEDEC SPD Revision 2 tAC = 5.4 ns 12 MOSEL VITELIC V437432E24V WORLDWIDE OFFICES U.S.A. TAIWAN SINGAPORE UK & IRELAND 3910 NORTH FIRST STREET SAN JOSE, CA 95134 PHONE: 408-433-6000 FAX: 408-433-0952 7F, NO. 102 MIN-CHUAN E. ROAD, SEC. 3 TAIPEI PHONE: 886-2-2545-1213 FAX: 886-2-2545-1209 10 ANSON ROAD #23-13 INTERNATIONAL PLAZA SINGAPORE 079903 PHONE: 65-3231801 FAX: 65-3237013 NO 19 LI HSIN ROAD SCIENCE BASED IND. PARK HSIN CHU, TAIWAN, R.O.C. PHONE: 886-3-579-5888 FAX: 886-3-566-5888 JAPAN SUITE 50, GROVEWOOD BUSINESS CENTRE STRATHCLYDE BUSINESS PARK BELLSHILL, LANARKSHIRE, SCOTLAND, ML4 3NQ PHONE: 44-1698-748515 FAX: 44-1698-748516 ONZE 1852 BUILDING 6F 2-14-6 SHINTOMI, CHUO-KU TOKYO 104-0041 PHONE: 03-3537-1400 FAX: 03-3537-1402 GERMANY (CONTINENTAL EUROPE & ISRAEL) BENZSTRASSE 32 71083 HERRENBERG GERMANY PHONE: +49 7032 2796-0 FAX: +49 7032 2796 22 U.S. SALES OFFICES WEST CENTRAL / EAST 3910 NORTH FIRST STREET SAN JOSE, CA 95134 PHONE: 408-433-6000 FAX: 408-433-0952 604 FIELDWOOD CIRCLE RICHARDSON, TX 75081 PHONE: 214-352-3775 FAX: 214-904-9029 © Copyright , MOSEL VITELIC Corp. Printed in U.S.A. The information in this document is subject to change without notice. MOSEL VITELIC makes no commitment to update or keep current the information contained in this document. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of MOSEL-VITELIC. V437432E24V Rev. 1.0 January 2002 13 MOSEL VITELIC subjects its products to normal quality control sampling techniques which are intended to provide an assurance of high quality products suitable for usual commercial applications. MOSEL VITELIC does not do testing appropriate to provide 100% product quality assurance and does not assume any liability for consequential or incidental arising from any use of its products. If such products are to be used in applications in which personal injury might occur from failure, purchaser must do its own quality assurance testing appropriate to such applications.