NJW1163/A AUDIO PROCESSOR with Subwoofer Output ■ GENERAL DESCRIPTION The NJW1163/A is a sound processor with subwoofer output includes all of functions processing audio signal for TV, such as tone control, balance, volume, mute, and AGC functions. Also the NJW1163/A includes the LPF for subwoofer output and bass boost function. The original surround system reproduces natural surround sound and clear vocal orientation. 2 All of internal status and variables are controlled by I C BUS interface. ■ PACKAGE OUTLINE NJW1163V NJW1163AL ■ FEATURES ● Operating Voltage 7.5 to 13V ● 3ch Output(Lch, Rch, Subwoofer ch) / 2ch Output(Lch, Rch) ● LPF Filter (Adjustable cut off frequency by external parts) ● AGC Circuit (It reduces volume difference among input sources.) 2 Adjustable AGC boost level by external parts and AGC compression level by I C BUS ● eala(NJRC Original Surround System) ● Simulated Stereo 2 ● I C BUS Interface ● Bi-CMOS Technology ● Package Outline NJW1163: SSOP32 NJW1163A: SDIP32 ■ BLOCK DIAGRAM AGC1 SS-FIL VOL1 IN a TONE VOL1 OUTa SCL SDA ADR VOL2 I2 CBUS Interface eal a & Simulated Stereo AGC IN b TONE TONE -Ha -La LF1 LF2 LF3 LPF TONE VOL2 Trimmer PORT1 PORT0 AUX1 AUX0 VOL2 Bias AGC2 SR-FIL TONE TONE -Hb -Lb OUTb OUTw CVA CVB CVW CTH CTL CSR GND V+ Vref -1- NJW1163/A ■PIN CONFIGURATION No. Symbol 1 INa INb 32 2 SR-FIL LF2 31 3 SS-FIL LF3 30 4 TONE-Ha LF1 29 5 TONE-La TONE-Hb 28 6 OUTW TONE-Lb 27 7 OUTa OUTb 26 8 AGC1 AGC2 25 9 AUX0 CVA 24 10 AUX1 CVB 23 11 PORT0 CVW 22 12 PORT1 CTH 21 13 ADR CTL 20 14 SDA CSR 19 15 SCL Vref 18 16 GND V+ 17 Function No. Symbol Function 1 INa Ach input terminal 17 V+ Supply voltage terminal 2 SR-FIL Surround filter terminal 18 Vref Reference voltage terminal 3 SS-FIL Simulated stereo filter terminal 19 CSR DAC output terminal for surround control 4 TONE-Ha Ach tone control (treble) filter terminal 20 CTL DAC output terminal for tone control (bass) 5 TONE-La Ach tone control (bass) filter terminal 21 CTH DAC output terminal for tone control (treble) 6 OUTw Subwoofer output terminal 22 CVW Bch DAC output terminal for LPF trimmer 7 OUTa Ach output terminal 23 CVB Bch DAC output terminal for volume and balance 8 AGC1 24 CVA Ach DAC output terminal for volume and balance 25 AGC2 AGC boost level setting terminal 26 OUTb Bch output terminal 27 TONE-Lb Bch tone control (bass) filter terminal Bch tone control (treble) filter terminal 10 AUX1 11 PORT0 AGC attack and recovery time setting terminal Auxiliary 3 values voltage output terminal (0.0V, 2.5V, 5V) Auxiliary 2 values voltage output terminal (0.0V, V+) Logic input terminal 12 PORT1 Logic input terminal 28 TONE-Hb 13 ADR Slave address setting terminal 29 LF1 LPF filter1 terminal 14 SDA I2C data terminal 30 LF3 LPF filter3 terminal 15 SCL I2C cock terminal 31 LF2 LPF filter2 terminal 16 GND Ground terminal 32 INb Bch input terminal 9 (✳) AUX0 (✳) -2- The AUX0 terminal should be connected via the protection resistance to 5V device. NJW1163/A ■ ABSOLUTE MAXIMUM RATING (Ta=25°C) PARAMETER SYMBOL RATING UNIT 15 V + Supply Voltage V Power Dissipation PD 700 mW Operating Temperature Range Topr -20 to +75 °C Storage Temperature Range Tstg -40 to +125 °C ■ ELECTRICAL CHARACTERISTICS ( Ta=25°C, V+=9V, Rg=600Ω, RL=47kΩ, Vin=100mVrms/1kHz unless otherwise specified) Condition PARAMETER SYMBOL Input Output INa INb + Operating Voltage Supply Current V ICC No Signal Reference Voltage VREF No Signal Maximum Input Voltage VIM VOL=-20dB,THD=1% VOM VOL=0dB, THD=1% Maximum Output Voltage Channel Balance Balance Boost A GCB BABST Balance Cut A BACUT Balance Boost B BBBST Balance Cut B BBCUT Trimmer Boost TRBST Trimmer Cut TRCUT Total Harmonic Distortion THD Maximum Gain GVMAX Minimum Gain GVMIN Channel Separation CS Output Noise 1 VNO1 Output Noise 2 VNO2 Output Noise 3 VNO3 VOL=0dB CHS=”0”,BAL=”111111” CHS=”1”, BAL=”111111” Vin = 1Vrms CHS=”1”,BAL=”111111” CHS=”0”, BAL=”111111” Vin = 1Vrms VOL=0dB TRIM = +18dB VOL=0dB TRIM = -44dB Vo=0.5Vrms, BW=400Hz to 30kHz VOL=0dB VOL=MUTE Vin=1Vrms Vin=1Vrms BW=400Hz to 30kHz VOL=0dB BW=400Hz to 30kHz VOL=MUTE BW=400Hz to 30kHz VOL=MUTE,TRIM=MUTE BW=400Hz to 30kHz MIN. TYP. MAX. UNIT - - - 7.5 - 9.0 13 13.0 25 V mA Vin Vin Vin Vin Vin Vin OUTa OUTb OUTa OUTb OUTa 4.0 4.5 5.0 V 2.8 3.0 - Vrms - 2.5 - Vrms -1.5 -2.0 0.0 0.0 1.5 2.0 dB dB Vin Vin OUTa - - -70 dB Vin Vin OUTb -2.0 0.0 2.0 dB Vin Vin OUTb - - -70 dB Vin Vin OUTw 16.0 18.0 20.0 dB Vin Vin OUTw -49.0 -44.0 -39.0 dB Vin Vin Vin Vin - Vin Vin Vin Vin OUTa OUTb OUTa OUTb OUTa OUTb OUTb OUTa - - 0.5 % -2.0 0.0 2.0 dB - - -70 dB - - -70 dB - - - - - - - - -90 (31.6) -106 (5.0) -85 (56.2) -96 (15.8) dBV (µVrms) dBV (µVrms) - - - - -100 (10.0) -90 (30.0) dBV (µVrms) BW : Band Width - 3 - NJW1163/A ■ ELECTRICAL CHARACTERISTICS (Ta=25°C, V+=9V, Rg=600Ω, RL=47kΩ, Vin=100mVrms/1kHz unless otherwise specified) Condition PARAMETER SYMBOL Input Output INa INb MIN. TYP. MAX. UNIT 12.5 15.0 17.5 dB -2.0 0.0 2.0 dB -17.5 -15.0 -12.5 dB 12.5 15.0 17.5 dB -2.0 0.0 2.0 dB -17.5 -15.0 -12.5 dB 1.5 3.5 5.5 dB -2.5 0.0 2.5 dB -2.5 0.0 2.5 dB -2.5 0.0 2.5 dB -2.5 0.0 2.5 dB -14 -10 -6.0 dB 6.3 8.3 10.3 dB 2.1 4.1 6.1 dB 10.7 12.7 14.7 dB 8.4 10.4 12.4 dB 1.0 1.0 3.0 3.0 5.0 5.0 dB dB 3.5 4.5 2.0 0 3.5 0 3.5 - 1.0 5.5 3.0 0.5 V+ 0.5 - - - 1.0 ♦TONE High Frequency Boost HFBST BCT=”1” TREB=+15dB, f=10kHz High Frequency Flat HFFLT TREB=0, f=10kHz High Frequency Cut HFCUT BCT=”0” TREB=-15dB, f=10kHz Low Frequency Boost LFBST BCB=”1” BASS=+15dB, f=100Hz Low Frequency Flat LFFLT BASS=0, f=100Hz Low Frequency Cut LFCUT BCB=”0” BASS=-15dB, f=100Hz Vin Vin Vin Vin Vin Vin - Vin Vin Vin Vin Vin Vin OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb OUTa OUTb Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin Vin OUTa OUTb OUTb OUTa OUTa OUTb OUTb OUTa OUTa OUTb - - - - - - - - - - - - ◆AGC AGC Boost AGCBST AGC Flat1 AGCFLT1 AGC Flat2 AGCFLT2 AGC Flat3 AGCFLT3 AGC Flat4 AGCFLT4 AGC Cut AGCCUT Vin=50mVrms, f=1kHz AGC=”1” Vin=100mVrms,f=1kHz AGC=”1”, AGCL=”00” Vin=200mVrms, f=1kHz AGC=”1”, AGCL=”01” Vin=300mVrms, f=1kHz AGC=”1”, AGCL=”10” Vin=400mVrms, f=1kHz AGC=”1”, AGCL=”11” Vin=2Vrms, f=1kHz AGC=”1” ◆SURROUND Surround Gain1 SRGAIN1 Surround Gain2 SRGAIN2 Surround Gain3 SRGAIN3 Surround Gain4 SRGAIN 4 Simulated Stereo1 Simulated Stereo2 SRSIM1 SRSIM2 f=100Hz Surround Effect1 f=100Hz Surround Effect1 f=100 Hz Surround Effect2 f=100Hz Surround Effect2 f=1kHz, Simulated Stereo f=1kHz, Simulated Stereo ◆PORT, AUX PORT0,1 Input Voltage VPTIN AUX0 Output Voltage VAUX0 AUX1 Output Voltage VAUX1 ADR Input Voltage VADR -4- Input : High Input : Low Logic Output : High Logic Output : Mid Logic Output : Low Logic Output : High Logic Output : Low Input : High Input : Low V V V V NJW1163/A 2 ■ I C BUS BLOCK CHARACTERISTICS (SDA,SCL) PARAMETER SYMBOL MIN. TYP. MAX. UNIT High Level Input Voltage VIH 3.0 - 5.0 V Low Level Input Voltage VIL 0 - 1.5 V High Level Input Current IIH - - 10 µA Low Level Input Current IIL - - 10 µA Low Level Output Voltage (3mA at SDA pin) VOL 0 - 0.4 V Maximum Output Current IOL -3.0 - - mA Maximum Clock Frequency fSCL - - 100 kHz Data Change Minimum Waiting Time tBUF 4.7 - - µs tHD:STA 4.0 - - µs Low Level Clock Pulse Width tLOW 4.7 - - µs High Level Clock Pulse Width tHIGH 4.0 - - µs Minimum Start Preparation Waiting Time tSU:STA 4.7 - - µs Minimum Data Hold Time tHD:DAT 0 - 3.45 µs Minimum Data Preparation Time tSU:DAT 250 - - ns Rise Time tR - - 1.0 µs Fall Time tF - - 300 ns tSU:STO 4.0 - - µs Data Transfer Start Minimum Waiting Time Minimum Stop Preparation Waiting Time 2 I C BUS Load Condition: Pull up resistance 4kΩ (Connected to +5V) Load capacitance 200pF (Connected to GND) SDA tBUF tR tHD:STA tF SCL tHD:STA tLOW P S tHD:DAT tHIGH tSU:STA tSU:DAT Sr tSU:STO P - 5 - NJW1163/A !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE V+ 1,32 pin 1 32 INa INb 20k Ach input terminal Bch input terminal V+/2 80k Vref 6 7 26 OUTw OUTa OUTb Subwoofer output terminal Ach output terminal Bch output terminal 100 V+/2 1.8k 2 SRFIL Surround filter terminal FB FB SSFIL Simulated stereo filter terminal 4 28 TONE-Ha TONE-Hb Treble(tone control) filter terminal -6- FB 2pin V+/2 5.3k 3 6, 7, 26pin FB 3pin V+/2 18k 4, 28pin V+/2 NJW1163/A !TERMINAL DESCRIPTION No. SYMBOL FUNCTION 5 27 TONE-La TONE-Lb Bass(tone control) filter terminal 8 AGC1 Capacitor connection terminal for AGC attack and recovery time setting EQUIVALENT CIRCUIT 12k VOLTAGE 5, 27pin V+/2 12k FB 8pin 400 12k 400 AGC; OFF=0.65V ON=1.4V 1k 9pin 9 AUX0 Auxiliary 3 values voltage output terminal AUX1 Auxiliary 2 values voltage output terminal (Open collector type output) FB 10pin 10 Low=0V Mid=2.5V High= 5.0V Low=0V High=3.5V to V+ 12k 5V 11 12 13 PORT0 PORT1 ADR Logic input terminal Logic input terminal Slave address setting terminal 11, 12, 13pin 560 - (Don’t apply over 5V to these terminals) - 7 - NJW1163/A !TERMINAL DESCRIPTION No. SYMBOL FUNCTION EQUIVALENT CIRCUIT VOLTAGE D1 D2 14 SDA D13 2 I C data terminal 14pin D14 - 4k 8k D1 D2 15 SCL D13 2 I C clock terminal 15pin D14 - 4k 8k 16 17 GND V+ Ground terminal Supply voltage terminal - 18pin 18 Vref V+/2 200k Reference voltage terminal V+/2 200k 19pin 19 CSR 0V DAC output for surround control terminal 32k -8- NJW1163/A !TERMINAL DESCRIPTION No. SYMBOL FUNCTION 20 21 CTL CTH DAC output for tone control terminal 22 23 24 CVW CVB CVA DAC output terminal for trimmer control DAC output terminal for Bch volume control DAC output terminal for Ach volume control 25 AGC2 Resistance connection terminal for AGC boost level setting EQUIVALENT CIRCUIT 20, 21pin 36k VOLTAGE V+/2 8k 22, 23, 24pin V+/2 25pin 0V 4k 30,31pin 30 31 LF3 LF2 LPF filter terminal V+/2+0.7V 29pin 29 LF1 LPF filter terminal V+/2 24k - 9 - NJW1163/A ■ MEASUREMENT CIRCUIT 0.47µ Input Ach 0.47µ 1 INa INb 32 2 SR-FIL LF2 31 3 SS-FIL LF3 30 LF1 29 0.047µ 100n Vin 100n 0.033µ 4 TONE -Ha 100n 2.2n 5 TONE -La TONE-Hb 6 TONE-Lb 28 4.7µ Output Ach 100n OUTw 27 4.7µ 47k 47k 7 OUTa OUTb 26 8 AGC1 AGC2 25 9 AUX0 CVA 24 330nF 4.7µ Output Bch 100k 47k 4.7µ AUX0 4.7µ AUX1 (✳1) CVB 23 11 PORT0 CVW 22 12 PORT1 CTH 21 10 AUX1 4.7µ (✳2) 4.7µ PORT0 VPTIN0 4.7µ PORT1 ADR Vin 0.022µ 2.2n Output Wch 13 ADR CTL 20 14 SDA CSR 19 15 SCL Vref 18 16 GND V+ 17 4.7µ VPTIN1 4.7µ VADRIN SDA (✳3) Vref Icc 22µ SCL (✳1) VAUX0 Output High Output Low IAUX0 +2mA -120µA VAUX1 Output Low IAUX1 -3mA VOL Output Low IOL -3mA (✳2) (✳3) - 10 - Input Bch V+ V+ NJW1163/A ■ APPLICATION CIRCUIT 0.47µ 0.47µ 5V 1 INa INb 32 100n 2 SR-FIL LF2 31 0.047µ 100n 3 SS-FIL LF3 30 0.022µ 2.2n 4 TONE-Ha LF1 29 0.033µ 100n 5 TONE-La TONE-Hb 28 2.2n 4.7µ 6 OUTw TONE-Lb 27 100n 4.7µ 7 OUTa OUTb 26 4.7µ 330nF 8 AGC1 AGC2 25 100k 4.7k 9 AUX0 CVA 24 4.7µ 10 AUX1 CVB 23 4.7µ 11 PORT0 CVW 22 4.7µ 12 PORT1 CTH 21 4.7µ 13 ADR CTL 20 4.7µ 14 SDA CSR 19 4.7µ 15 SCL Vref 18 4.7µ 16 GND V+ 17 220 220 (✳4) 100 220 22µ (✳4) Set the Slave Address by “ADR” terminal. ADR (Pin 13) GND +5V 2 I C Slave Address Read mode Write mode 80h 81h 82h 83h 2 (✳5) Separate the I C bus line and Signal line from the following terminals for avoiding digital noise problem and cross talk. Pin No. Symbol Pin No. Symbol Pin No. Symbol 2 SR-FIL 27 TONE-Lb 31 LF2 3 SS-FL 28 TONE-Hb 4 TONE-Ha 29 LF1 5 TONE-La 30 LF3 - 11 - NJW1163/A ■ LPF Characteristics Secondary LPF GmAmp2 Buffer2 Primary LPF GmAmp3 Buffer3 LF2 C2 R1 24k LF3 C3 LF1 C1 LPF Block Diagram The NJW1163 includes the LPF for subwoofer output and bass boost function. The LPF consists of primary and secondary LPF and it is enable to adjust “cut off frequency”, “Q” and “Roll off”. The expression of LPF characteristics is as follows. <Primary LPF> f c1 = 1 1 = 2π * R * C1 2π * 24 *10 3 * C1 Q1 = 0.5 <Secondary LPF> f c2 = 42.9 ∗10 −6 Q 2 = 1.46 * 2π C 2 ∗ C 3 C3 C2 <LPF Frequency Response> C2 = 47nF, C3 = 22nF 5 5 C1=22nF -5 -5 C2=68nF C2=100nF -10 -10 -15 -15 -20 Frequency [kHz] 1 -5 C3=22nF C3=15nF C3=10nF -10 -15 -20 0.1 C3=33nF 0 C2=47nF G C1=47nF C1=68nF - 12 - C2=33nF 0 C1=33nF Gain[dB] 0 C3=47nF C 2 C1=15nF Gain[dB] C1 = 33nF, C2 = 47nF C1 = 33nF, C 5 -20 0.1 1 Fr 0.1 Frequency [kHz] 1 NJW1163/A 2 ■ DEFINITION OF I C REGISTER 2 ♦I C BUS FORMAT MSB S LSB Slave Address 1bit 8bit MSB LSB A Select Address 1bit 8bit MSB LSB A 1bit Data A P 8bit 1bit 1bit S: Starting Term A: Acknowledge Bit P: Ending Term ♦SLAVE ADDRESS R/W ADR : Set the Write Mode or Read Mode. : Set the Slave Address by “ADR” terminal. (See Application Circuit) Slave Address Hex MSB 1 0 0 0 0 0 ADR LSB - R/W - ◆ R/W = 0 : Write Mode, ADR = 0/1 - 1 0 0 0 0 0 0 0 80(h) 1 0 0 0 0 0 1 0 82(h) ◆ R/W = 1 : Read Mode, ADR = 0/1 - 1 0 0 0 0 0 0 1 81(h) 1 0 0 0 0 0 1 1 83(h) ♦CONTROL REGISTER TABLE The select address sets each function (Volume, Balance, Bass Boost Select, AGC, Surround, Tone Control, AUX). The auto increment function cycles the select address as follows. 00H→01H→02H→03H→04H→05H→00H <Write Mode> BIT Select Address D7 00H 01H CHS 02H 03H 04H 05H D6 D4 D5 D3 D2 D1 D0 VOL BAL BBSW ✴ TRIM BASS TREB BCB BCT SUR AUX1 ✴ ✴ AUX0 AGCL AGC ✴ : Don’t Care <Read Mode> BIT D7 D6 D4 D5 D3 D2 D1 D0 1 1 1 1 1 1 PORT1 PORT0 •PORT1, PORT0 terminal setting D1/D0 Remarks 0 D1/D0 output “0” at PORT1/PORT0 terminal receive High signal “1” (more than 3.5V) 1 D1/D0 output “1” at PORT1/PORT0 terminal receive Low signal “0” (less than 1.0V) ♦CONTROL REGISTER DEFAULT VALUE Control register default value is all “0”. BIT Select Address D7 D6 D5 D4 D3 D2 D1 D0 00H 01H 02H 03H 04H 05H 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 - 13 - NJW1163/A !INSTRUCTION CODE a) MASTER VOLUME SETTING Select Address BIT D7 D6 D5 D4 D3 D2 D1 D0 00H VOL •VOL Attenuation level : 0 to –80dB(0.33dB/step) , MUTE The attenuator is consisted of both the VOL1(0.165dB/step)and VOL2(0.165dB/step) and is enable to adjust 0.33dB/step. The attenuation for both the VOL1and VOL2 are always synchronized to have the same attenuation levels for each other, and are not controllable independently for each other. ex) VOL(-30dB) = VOL1(-15dB) + VOL2(-15dB) b) BALANCE AND BASS BOOST FUNCTION SETTING BIT Select Address D7 01H CHS D6 D5 D4 D3 D2 D1 BAL D0 BBSW •CHS : Channel select for balance control “0” : Ach “Bch is attenuated” “1” : Bch “Ach is attenuated” •BAL : Balance control for both Ach and Bch Balance Level : 0 to –60dB (1dB/Step) , MUTE •BBSW : Bass Boost ON/OFF Switch “0” = Bass Boost OFF “1” = Bass Boost ON c) TRIMMER LEVEL SETTING Select Address BIT D7 D6 D5 D4 D3 D2 D1 02H TRIM •TRIM : Trimmer Level Trimmer Level : +18 to –44dB (0.5dB/Step) , MUTE D0 Don’t Care d) TONE CONTROL BASS SETTING BIT Select Address D7 03H BCB D6 D5 D4 D3 D2 D1 BASS D0 Don’t Care •BCB : Boost cut select for Bass control “0” : Cut “1” : Boost •BASS : BASS Level Setting Cut Level : -15 to 0dB(0.5dB/Step) Boost Level : 0 to +15dB(0.5dB/Step) d) TONE CONTROL TREBLE SETTING BIT Select Address D7 04H BCT D6 D5 •BCT : Boost cut select for Treble control “0” : Cut “1” : Boost •TREB : TREBLE Level Setting Cut Level : -15 to 0dB(0.5dB/Step) Boost Level : 0 to +15dB(0.5dB/Step) - 14 - D4 TREB D3 D2 D1 D0 Don’t Care NJW1163/A d) SURROUND, AUXILIARY, AGC LEVEL SETTING Select Address BIT D7 05H D6 D5 SUR D4 AUX1 D3 AUX0 D2 D1 AGCL D0 AGC <SUR : Surround Level Setting> Surround Setting Surround Off Simulated Stereo Surround Effect1 Surround Effect2 D7 0 0 1 1 D6 0 1 0 1 Remarks Surround Off Simulated Stereo Surround Effect Low(8.3dB typ.) Surround Effect High(12.7dB typ.) <AUX1 : AUX1 Terminal Setting> Auxiliary Setting Low (0.0V) High (5.0V) D5 0 1 <AUX0 : AUX0 Terminal Setting> Auxiliary Setting Low (0.0V) Mid (2.5V) High (5.0V) D4 0 1 D3 0 1 1 D2 0 0 1 1 D1 0 1 0 1 <AGCL : AGC Level Setting> AGC Level Setting 100mVrms 200mVrms 300mVrms 400mVrms <AGC : AGC Setting> AGC Setting OFF ON D0 0 1 - 15 - NJW1163/A ■Master Volume (Select Address : 00H) VOL Gain(dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 -23 -24 -25 -26 -27 -28 -29 -30 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 -41 -42 FF FC F9 F6 F3 F0 ED EA E7 E4 E1 DE DB D8 D5 D2 CF CC C9 C6 C3 C0 BD BA B7 B4 B1 AE AB A8 A5 A2 9F 9C 99 96 93 90 8D 8A 87 84 81 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 - 16 - NJW1163/A VOL Gain(dB) HEX D7 D6 D5 D4 D3 D2 D1 D0 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 -56 -57 -58 -59 -60 -61 -62 -63 -64 -65 -66 -67 -68 -69 -70 -71 -72 -73 -74 -75 -76 -77 -78 -79 -80 MUTE✴ 7E 7B 78 75 72 6F 6C 69 66 63 60 5D 5A 57 54 51 4E 4B 48 45 42 3F 3C 39 36 33 30 2D 2A 27 24 21 1E 1B 18 15 12 0F 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 1 1 0 0 0 1 1 0 0 0 1 1 1 0 0 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 1 0 1 0 0 1 0 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 ✴ : Default Value - 17 - NJW1163/A ■Balance, Bass Boost Setting (Select Address : 01H) Channel Setting (CHS) D7 Decrease Bch Gain Decrease Ach Gain 0 1 Gain(dB) - 18 - BAL D6 D5 D4 D3 D2 D1 0✴ -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 -22 -23 0 0 1 1 0 0 1 1 1 1 0 1 -24 -25 -26 -27 -28 -29 -30 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 ✴ : Default Value NJW1163/A Gain(dB) BAL D5 D4 D3 D2 D1 -31 -32 -33 -34 -35 -36 -37 -38 -39 -40 -41 -42 -43 -44 -45 -46 -47 -48 -49 -50 -51 -52 -53 -54 -55 D6 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 -56 -57 1 1 1 1 1 1 0 0 0 0 0 1 -58 -59 -60 MUTE 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 0 1 0 1 0 1 Bass Boost Setting (BBSW) D0 Bass Boost Off✴ Bass Boost On 0 1 ✴ : Default Value - 19 - NJW1163/A ■Trimmer Setting (Select Address: 02H) TRIM Gain(dB) D7 D6 D5 D4 D3 D2 D1 +18.0 +17.5 +17.0 +16.5 +16.0 +15.5 +15.0 +14.5 +14.0 +13.5 +13.0 +12.5 +12.0 +11.5 +11.0 +10.5 +10.0 +9.5 +9.0 +8.5 +8.0 +7.5 +7.0 +6.5 +6.0 +5.5 +5.0 +4.5 +4.0 +3.5 +3.0 +2.5 +2.0 +1.5 +1.0 +0.5 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 -5.5 -6.0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 - 20 - NJW1163/A TRIM Gain(dB) D7 D6 D5 D4 D3 D2 D1 -6.5 -7.0 -7.5 -8.0 -8.5 -9.0 -9.5 -10.0 -10.5 -11.0 -11.5 -12.0 -12.5 -13.0 -13.5 -14.0 -14.5 -15.0 -15.5 -16.0 -16.5 -17.0 -17.5 -18.0 -18.5 -19.0 -19.5 -20.0 -20.5 -21.0 -21.5 -22.0 -22.5 -23.0 -23.5 -24.0 -24.5 -25.0 -25.5 -26.0 -26.5 -27.0 -27.5 -28.0 -28.5 -29.0 -29.5 -30.0 -30.5 -31.0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 - 21 - NJW1163/A TRIM Gain（ｄ （ｄB） （ｄ ） D7 D6 D5 D4 D3 D2 D1 -31.5 -32.0 -32.5 -33.0 -33.5 -34.0 -34.5 -35.0 -35.5 -36.0 -36.5 -37.0 -37.5 -38.0 -38.5 -39.0 -39.5 -40.0 -40.5 -41.0 -41.5 -42.0 -42.5 -43.0 -43.5 -44.0 MUTE✴ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 ✴ : Default value - 22 - NJW1163/A ■Tone Control(Bass Setting) (Select Address : 03H) Bass Cut or Boost BCB D7 Cut Boost 0 1 BASS Cut Gain(dB) Boost Gain(dB) D6 D5 D4 D3 D2 -15.0 -14.5 -14.0 -13.5 -13.0 -12.5 -12.0 -11.5 -11.0 -10.5 -10.0 -9.5 -9.0 -8.5 -8.0 -7.5 -7.0 -6.5 -6.0 -5.5 -5.0 -4.5 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0✴ 15.0 14.5 14.0 13.5 13.0 12.5 12.0 11.5 11.0 10.5 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0✴ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 0 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0 ✴ : Default value - 23 - NJW1163/A ■Tone Control(Treble Setting) (Select Address : 04H) Treble Cut or Boost BCT D7 Cut Boost 0 1 TREB Cut Gain(dB) Boost Gain(dB) D6 D5 D4 D3 D2 -15.0 -14.5 -14.0 -13.5 -13.0 -12.5 -12.0 -11.5 -11.0 -10.5 -10.0 -9.5 -9.0 -8.5 -8.0 -7.5 -7.0 -6.5 -6.0 -5.5 -5.0 -4.5 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0✴ 15.0 14.5 14.0 13.5 13.0 12.5 12.0 11.5 11.0 10.5 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0✴ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 1 0 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0 ✴ : Default value [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 24 -