NTE NTE1764

NTE1764
Integrated Circuit
Infrared Preamplifier
Description:
The NTE1764 is an infrared preamplifier in a 14–Lead DIP type package and contains four main parts:
the gain–controlled amplifier I, the amplifier II, the pulse–separating amplifier III, and the inverter IV.
The amplifier I has a wide dynamic range and thus ensures interference free operation, also at bright
ambient light, 50Hz modulated light originating from fluorescent lamps, or at intensive infrared light,
e.g. produced by infrared sound transmission. It is also possible, to approach almost directly the remote–control transmitter to the receiver without producing misfunction by overdriving the receiver.
The amplifier II further amplifies the signal, and amplifier III separates the pulse–shaped intelligence
signal from noise and other unwanted parts. The inverter IV provided additionally inverts the output
signal available at Pin7 as negative pulse, and thus delivers positive output pulses at Pin8. If an additional resistor is inserted between Pin6 and GND, the noise–immunity is increased, but the input sensitivity decreased. Pin10 serves as test pin and must not be connected.
The capacitor connected from Pin2 to GND influences the automatic gain control of amplifier I contained in the NTE1764. A capacitance of less than 1µF will cause misfunction in the distance range
of 0.2, to 2m.
Absolute Maximum Ratings: (Note 1)
Supply Voltage, V3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Ambient Operating Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20° to +65°C
Storage Temperature Range, TS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –30° to +125°C
Recommended Operating Conditions: (Note 1)
Parameter
Supply Voltage
Symbol Min Typ Max Unit
V3
4.5 5.0 5.5
V
Electrical Characteristics: (V3 = 5V, TA = +25°C, Note 1)
Parameter
Symbol
Min
Typ
Max
Unit
Current Consumption
Gain Between Pin14 & Pin7
Output Resistance Pin7 & Pin8, formed by the Pull–Up of an
NPN Transistor
Output Low Voltage Pin7 & Pin8 at IOL = 1.6mA
IR Transmission Range using the SAA1250 IR Transmitter IC
and a Transmission Current Amplitude of 1.5A, and
One Transmitter Diode (NTE3017)
I2
G
RO
–
70
–
1
–
20
2
–
–
mA
dB
kΩ
VOL
–
0.4
0.8
V
L1
–
12
–
m
L2
L3
–
–
19
20
–
–
m
m
Two Transmitter Diodes (NTE3017)
Three Transmitter Diodes (NTE3017)
Note 1. All voltages are referred to GND (Pin1, Pin9, and Pin13).
Pin Connection Diagram
Input’s GND, 0
1
14 Input Amplifier I
Capacitor Pin Amplifier I
2
13 GND, 0, of Amplifier II
Supply Voltage VB
3
12 Ouptut Amplifier I
Input Amplifier III
4
11 Input Amplifier II
Output Amplifier II
5
10 Test Pin/N.C.
Separation Threshold Adjust
6
9
Output’s GND, 0
Negative Pulse Output
7
8
Positive Pulse Output
14
8
1
7
.300 (7.62)
.785 (19.95) Max
.200
(5.08)
Max
.100 (2.45)
.600 (15.24)
.099 (2.5) Min