DATA SHEET CP600~CP6010 SINGLE-PHASE SILICON BRIDGE-P.C. MTG 3A , HEAT-SINK MTG 6A VOLTAGE 50 to 1000 Volts CURRENT - P.C. MTG 3A , HEAT-SINK MTG 6A .752(19.1) MIN FEATURES • Plastic package has Underwriters Laboratory Flammability Classification 94V-O . • Surge Overload Ratings to 125 Amperes. .268(6.8) .228(5.8) Recongnized File # E111753 .044(1.1) .039(1.0) • Low forward voltage, and reverse leakage. • Small size , simple installation. .445(11.3) .406(10.3) MECHANICAL DATA .618(15.7) .579(14.7) .15(3.8) MIN • Reliable low cost construction utilizing molded plastic technique. Mounting Position: Any .445(11.3) .406(10.3) Weight: 0.2 ounce, 5.6 gram Terminals: Lead solderable per MIL-STD-202 Method 208 Mounting Torque: 5 in. lb. max. .618(15.7) .579(14.7) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase , half wave ,60Hz, resistive or inductive load. For capacitive load , derate current by 20%. CP600 CP601 CP602 CP604 CP606 CP608 CP6010 UNITS Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V Maximum RMS Bridge input Voltage 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage 50 100 200 400 600 600 1000 V 6 3 A Peak Forward Surge Current ,8.3ms single half sine-wave superimposed on rated load 125 A Maximum Forward Voltage per Bridge Element Specified Current at 3.0A DC & 25°C.See Fig 3 1.1 V 10.0 1.0 µA mA I2t Rating for fusing ( t < 8.35 ms) 127 Typical junction capacitance per leg (NOTE 4)CJ 186 A2S pF Typical Thermal resistance per leg ( NOTE 3) RθJA 22.0 7.3 °C/W Operating Temperature Range TJ -55 to +125 °C Storage Temperature Range TA -55 to +150 °C Maximum Average Forward Current at TC=50°C at TA=25°C See Fig 2 Maximum Reverse Leakage at RatedDC Blocking Voltage per element. at 25°C See Fig 4 at 100°C Typical Thermal resistance per leg ( NOTE 2) RθJC NOTES: 1.Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw. 2.Unit mounted on 5.0 X 6.0 X 0.11” thick ( 14 X 15 X 0.3 cm )AL.plate. 3.Unit mounted on P.C.B at 0.395”(9.5mm)lead length with 0.5 X 0.5” ( 12 X 12 mm )copper pads. 4.Measured at 1.0MHZ and applied reverse voltage of 4.0 volts. INSTANTANEOUS FORWARD CURRENT, AMPERES OUTPUT CURRENTAMPERES RATING AND CHARACTERISTIC CURVES 6.0 4.0 2.0 0 0 50 100 5.0 4.0 3.0 2.0 1.0 .9 .8 .7 .5 .3 .2 .1 .07 .05 .03 .02 .01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 150 O AMBIENT TEMPERATURE C Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISITCS (25 C) 100 10 1.0 O T A =25 C 0.1 0 20 40 60 80 100 120 140 PERCENT OF PEAK REVERSE VOLTAGE Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT, MICROAMPERES O 125 100 75 50 25 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig. 4- MAXIMUM NON-REPETITEVE PEAK FORWARD SURGE CURRENT