PS301/PS302/PS303 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Precision, Single-Supply SPST Analog Switches Features Description • Low On-Resistance (33Ω typ) Minimizes Distortion and Error Voltages • Low Glitching Reduces Step Errors in Sample-and-Holds. Charge Injection, 2pC typ • Single-Supply Operation (+2.5V to +16V) • Improved Second Sources for MAX4501/MAX4502 • On-Resistance Matching Between Channels, <2Ω • On-Resistance Flatness, <6Ω max • Low Off-Channel Leakage, <5nA @ +85oC • TTL/CMOS Logic Compatible • Fast Switching Speed, tON < 150ns • Guaranteed Break-Before-Make action (PS303 only) eliminates momentary crosstalk • Rail-to-Rail Analog Signal Dynamic Range • Low Power Consumption, <5µW • MSOP Package minimizes board area The PS301/PS302/PS303 are improved high precision, medium voltage analog switches designed to operate with single power supplies. The PS301 is a single-pole single-throw (SPST), normally open (NO) switch. The PS302 has the same pinout as the PS301 but is a normally closed (NC) switch. The PS303 has one normally open (NO) and one normally closed (NC) switch per package. Each switch conducts current equally well in either direction when on. In the off state each switch blocks voltages up to the power-supply rail. With a +5V power supply, the PS301/PS302/PS303 guarantee <60Ω ON-resistance. ON-resistance matching between channels is within 2Ω. ON-resistance flatness is less than 6Ω over the specified range. All three devices guarantee low leakage currents (<100pA @ 25oC, <10nA @ +85oC) and fast switching speeds (tON < 150ns). Break-before-make switching action protects against momentary crosstalk (PS303). For single-supply operation below 5V, the PI5A317/318/319 are also recommended. Applications • • • • • • Audio, Video Switching and Routing Portable Instruments Data Acquisition Systems Sample-and-Holds Telecommunication Systems Battery-Powered Systems Functional Diagrams, Pin Configurations, and Truth Tables Top Views COM 1 8 NO N.C. 2 7 GND N.C. 3 V+ 4 PS301 6 IN 5 N.C. COM 1 8 NC N.C. 2 7 GND N.C. 3 V+ 4 PS302 6 IN 5 N.C. NO 1 8 V+ COM 2 7 IN NC 3 6 N.C. GND 4 5 N.C. PS303 Switches shown for logic “0” input PS302 PS301 PS303 Logic Switch Logic Switch Logic NC NO 0 1 O FF ON 0 1 ON O FF 0 1 ON O FF O FF ON For free samples and the latest literature: www.pericom.com, or phone 1-800-435-2336 1 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Absolute Maximum Ratings Thermal Information Voltages Referenced to GND V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +17V VIN, VCOM, VNC, VNO (Note 1) . . . . . . . . . -2V to (V+) +2V or 30mA, whichever occurs first Current (any terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA Peak Current, COM, NO, NC (pulsed at 1ms, 10% duty cycle) . . . . . . . . . . . . . . . . . . 100mA ESD per Method 3015.7 . . . . . . . . . . . . . . . . . . . . . . . >2000V Continuous Power Dissipation Plastic DIP (derate 6mW/ ºC above +70ºC) . . . . . . . . . 500mW Narrow SO (derate 6mW/ ºC above +70ºC) . . . . . . . . 450mW MSOP (derate 4mW/ ºC above +70ºC) . . . . . . . . . . . . 330mW Storage Temperature . . . . . . . . . . . . . . . . . . -65ºC to +150ºC Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . +300ºC Note 1: Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to 30mA maximum. Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Electrical Specifications - Single +5V Supply (V+ = 5V +10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parame te r Symbol Conditions Te mp. (°C) M in(2) Full 0 Typ(1) M ax(2) Units V+ V Analog Switch Analog Signal Range (3) On Resistance VANALOG RON V+ = 4.5V, VNO or VNC = +3.5V, ICOM = 1mA 25 33 Full VNO or VNC = +3V, ICOM = 1mA, V+ = 5V On- Resistance Match Between Channels(4) ∆RON On- Resistance Flatness(5) RFLAT(ON) V+ = 5V, ICOM =1mA , VNO or VNC = 1V, 2V, 3V, NO or NC Off Leakage Current(6) INO(OFF) or INC(OFF) V+ = 5.5V, VCOM = 1V, VNO or VNC = 4.5V COM Off Leakage Current(6) ICOM(OFF) V+ = 5.5V, VCOM = 4.5V, VNO or VNC = 1V COM On Leakage Current(6) ICOM(ON) 75 25 0.8 Full V+ = 5.5V , VCOM = 5V, VNO or VNC = 5V 60 2 Ω 4 25 2 Full 6 8 25 0.1 Full 5 25 0.1 Full 5 25 0.2 Full 10 Full 0.5 0.01 0.1 5 0.01 0.1 nA 5 0.04 0.2 10 Logic Input Input Current with Input Voltage High IINH Input Current with Input Voltage Low IINL Logic High Input Voltage VINH Logic Low Input Voltage VINL VIN = 2.4V, all others = 0.8V 0.005 0.5 µA VIN = 0.8V, all others = 2.4V 0.5 0.005 0.5 2.4 V 0.8 2 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Specifications - Single +5V Supply (continued) (V + = 5V ±10%, GND = 0V, VINH =2.4V, VINL = 0.8V) Parame te r Symbol Conditions Te mp. (°C) M in(1) Typ(2) M ax(1) Units Dynamic Turn- On Time Turn- Off Time tON 25 VNO or VNC = 3V, Figure 2 85 Full 240 25 tOFF 25 PS303 only, RL = 300Ω, CL= 35pF, Fig. 3 Charge Injection(3) Q CL= 1nF, VGEN = 0V, RGEN = 0Ω, Fig. 4 1 Off Isolation(7) OIRR RL = 50Ω, CL = 5pF, f = 1MHz, Fig. 5 72 Crosstalk XTALK RL = 50Ω, CL = 5pF, f = 1MHz, Fig. 6 85 NC or NO Off Capacitance C(OFF) 2 25 5 5 pC dB 9 f =1MHz, Figure 7 pF 9 CCOM(OFF) CCOM(ON) ns 150 tD COM On Capacitance 100 Full Break- Before- Make TimeDelay(3) COM Off Capacitance 150 f =1MHz, Figure 8 22 Supply Power- Supply Range V+ Positive Supply Current I+ V+ = 5.5V, VIN = 0V or V+, all channels on or off Full 2.7 16 V 1 1 µA Notes: 1. The algebraic convention, where the most negative value is a minimum and the most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design 4. ∆RΟΝ = RΟΝ max. - RΟΝ min. 5. Flatness is defined as the difference between the maximum and minimum value of on-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [VCOM / (VNCor VNO)]. See Figure 5. 3 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Specifications - Single +12V Supply (V+ = 12V ±10%, GND = 0V, VINH = 5V, VINL = 0) Parame te r Symbol Conditions Te mp (°C) M in(1) Typ(2) M ax(1) Units V+ V 35 Ω Analog Switch Analog Signal Range(3) On- Resistance VANALOG RON 0 V+ =12V, ICOM = 1mA, VNO or VNC = 6V 25 14 Full 45 Dynamic Turn- On Time(3) 25 tON VNO or VNC = 6V, Figure 2 Turn- Off Time(3) Break- Before- Make Time Delay(3) Charge Injection(3) tOFF Full 25 Full 25 Q CL = 1nF, VGEN = 6V, RGEN = 0Ω, Figure 4 25 I+ V+ = 13.2V, VIN = 0V or V+, all channels on or off Full 150 240 25 PS303 only tD 85 100 ns 150 2 5 pC Supply Positive Supply Current 1 0.01 1 µA M ax(1) Units V+ V 175 Ω Electrical Specifications - Single +3.3V Supply (V+ = 3.3V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parame te r Symbol Conditions Te mp (°C) M in(1) Typ(2) Analog Switch Analog Signal Range(3) On- Resistance VANALOG RON 0 V+ = 3V, ICOM = 1mA, VNO or VNC = 1.5V 25 83 Full 275 Dynamic Turn- On Time(3) 25 tON VNO or VNC = 1.5V, Figure 2 Turn- Off Time(3) tOFF 160 Full 500 25 40 Full Break- Before- Make Time Delay(3) tD PS303 only 25 Charge Injection(3) Q CL = 1nF, VGEN = 0V, RGEN = 0Ω, Figure 4 25 I+ V+ = 3.6V, VIN = 0V or V+, all channels on or off Full 400 125 ns 175 2 5 1 5 pC 0.01 1 µA Supply Positive Supply Current 4 1 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Test Circuits/Timing Diagrams +5V V+ NO or NC COM VCOM = 3V VOUT tr <20ns tf <20ns 50% tOFF CL 35pF RL 1kΩ IN Logic Input Logic +3V Input 0V Switch Output GND VOUT 90% 90% 0V tON CL INCLUDES FIXTURE AND STRAY CAPACITANCE RL VOUT = VCOM RL + RON ( LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE OPPOSITE LOGIC ) Figure 2. Switching Time V+ Logic +3V Input 0V V+ NC +3V NO1 V OUT 50% NO RL Ω300Ω IN Logic Input CL 35pF Switch Output 90% VOUT GND 90% tD 0V CLINCLUDES FIXTURE AND STRAY CAPACITANCE. Figure 3. Break-Before-Make Interval (PS303 only) +5V RGEN V+ VGEN VOUT IN CL OFF OFF ON 1nF IN Logic Input ∆VOUT VOUT NO or NC COM GND IN OFF ON OFF Q = (∆VOUT)(CL) IN POLARITY DEPENDS ON NO OR NC SWITCH FUNCTION Figure 4. Charge Injection 5 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Test Circuits/Timing Diagrams (continued) +5V 10nF 10nF Signal Generator 0dBm V+ +5V COM1 V+ IN COM Analyzer NC or NO COM Analyzer GND RL COM2 N02 Figure 6. Crosstalk +5V 10nF +5V V+ V+ COM f = 1kHz NC 50Ω Ω Figure 5. Off Isolation Capacitance Meter 0V or 2.4V GND RL 10nF IN2 IN1 0V or 3.5V 0V or 2.4V 50Ω N01 COM IN NC or NO Capacitance Meter 0V or 2.4V f = 1kHz COM IN NC or NO 0V or 2.4V GND GND Figure 7. Channel-Off Capacitance Figure 8. Channel-On Capacitance 6 PS8187A 06/29/99 PS301/PS302/PS303 Precision, Single Supply SPST Analog Switches 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Applications Information Positive Supply Overvoltage Protection Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings, because stresses beyond the listed ratings may cause permanent damage to the devices. Always sequence V+ on first, and then logic inputs. If power-supply sequencing is not possible, add two small signal diodes or two current limiting resistors in series with the supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog signal range, but low switch resistance and low leakage characteristics are unaffected. V+ NO COM Vg Logic Levels When powered from +5V the PS301/PS302/PS303 can be operated with either TTL- or CMOS-Logic levels. If V+ is different than +5V, the logic threshold level will vary. V- Power consumption is minimal when the logic control voltages reach V+ or GND. GND Figure 1. Overvoltage protection is accomplished by using two external blocking diodes or two current limiting resistors. Ordering Information Te mp. R ange Pack age PS302EPA 40ºC to +85ºC 8 Plastic DIP 8 N arrow SO PS302ESA 40ºC to +85ºC 8 N arrow SO 0ºC to +70ºC 8 MSO P PS303CPA 0ºC to +70ºC 8 Plastic DIP PS301EPA 40ºC to +85ºC 8 Plastic DIP PS303CSA 0ºC to +70ºC 8 N arrow SO PS301ESA 40ºC to +85ºC 8 N arrow SO PS303CUA 0ºC to +70ºC 8 MSO P PS302CPA 0ºC to +70ºC 8 Plastic DIP PS303EPA 40ºC to +85ºC 8 Plastic DIP PS302CSA 0ºC to +70ºC 8 N arrow SO PS303ESA 40ºC to +85ºC 8 N arrow SO PS302CUA 0ºC to +70ºC 8 MSO P Part Te mp. R ange Pack age PS301CPA 0ºC to +70ºC 8 Plastic DIP PS301CSA 0ºC to +70ºC PS301CUA Part Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 7 PS8187A 06/29/99