POWERINT DPA425

DPA423-426
DPA-Switch™ Family
Highly Integrated DC-DC Converter ICs
for Distributed Power Architectures
Product Highlights
Highly Integrated Solution
• Eliminates 20-50 external components–saves space, cost
• Integrates 220 V high frequency MOSFET, PWM control
• Lower cost plastic DIP surface mount (G package) and
through-hole (P package) options for designs ≤35 W
Superior Performance and Flexibility
• Eliminates all external current sensing circuitry
• Built-in auto-restart for output overload/open loop protection
• Pin selectable 300/400 kHz fixed frequency
• Wide input (line) voltage range: 16-75 VDC
• Source connected tab reduces EMI
• Line under-voltage (UV) detection: meets ETSI standards
• Line overvoltage (OV) shutdown protection
• Low cost synchronous rectification: line UV/OV shut down
limits gate drive voltage range from transformer winding
• Fully integrated soft-start for minimum stress/overshoot
• Externally programmable current limit
• Supports forward or flyback topology
• Cycle skipping: regulation to zero load without pre-load
• Hysteretic thermal shutdown for automatic fault recovery
®
EcoSmart - Energy Efficient
• Extremely low consumption at no load
• Cycle skipping at light load for high standby efficiency
Applications
• Telco central office equipment: xDSL, ISDN, PABX, etc.
• Distributed power architectures (24 V/48 V bus, etc.)
• Digital feature phones, VoIP phones, PoE
• Industrial controls (24 V/48 V)
Description
The DPA-Switch IC family introduces a highly integrated
solution for DC-DC conversion applications in the 16-75 VDC
input range.
DPA-Switch uses the same proven topology as TOPSwitch, cost
effectively integrating the high voltage power MOSFET, PWM
control, fault protection and other control circuitry onto a single
CMOS chip. High performance features are enabled with three
user configurable pins.
VO
SENSE
CIRCUIT
DPA-Switch
VIN
L
D
CONTROL
RESET/
CLAMP
CIRCUIT
S
X
C
F
PI-2770-032002
Figure 1. Typical Forward Converter Application.
OUTPUT POWER TABLE
36-75 VDC INPUT RANGE (FORWARD)2,4
Total Device
Dissipation3 0.5 W
PRODUCT4
DPA423
DPA424
DPA425
DPA426
12 W
16 W
23 W
25 W
1 W 2.5 W
4W
6W
16 W 23 W 35 W
32 W 50 W 62 W
35 W 55 W 70 W 83 W
Max
Power
Output1
18 W
35 W
70 W
100 W
36-75 VDC INPUT RANGE (FLYBACK)2
Total Device3
Dissipation
0.5 W
0.75 W
1W
1.5 W
PRODUCT4
DPA423
DPA424
DPA425
9W
13 W
10 W 14.5 W 18 W 24 W
-5
-5
-5
25.5 W
Max
Power
Output1
13 W
26 W
52 W
Table 1. Notes: 1. Maximum output power is limited by device internal
current limit. 2. See Applications Considerations section for complete
description of assumptions and for output powers with other input voltage
ranges. 3. For device dissipation of 1.5 W or below, use P or G packages.
Device dissipation above 1.5 W is possible only with R package. 4. See
Part Ordering Information. 5. Due to higher switching losses, the DPA425
may not deliver additional power compared to a smaller device.
The following transparent or built-in features are also provided:
soft-start, cycle skipping down to zero load and hysteretic
thermal shutdown. In addition, all critical parameters (i.e.
current limit, frequency, PWM gain) have tight temperature
and absolute tolerance, to simplify design and optimize system
cost.
January 2004
DPA423-426
Section List
Functional Block Diagram ......................................................................................................................................... 3
Pin Functional Description ........................................................................................................................................ 3
DPA-Switch Family Functional Description .............................................................................................................. 4
CONTROL (C) Pin Operation ................................................................................................................................. 4
Oscillator and Switching Frequency ....................................................................................................................... 5
Pulse Width Modulator & Maximum Duty Cycle ..................................................................................................... 6
Minimum Duty Cycle and Cycle Skipping ............................................................................................................... 6
Error Amplifier ......................................................................................................................................................... 6
On-chip Current Limit with External Programmability ............................................................................................. 6
Line Under-Voltage Detection (UV) ........................................................................................................................ 6
Line Overvoltage Shutdown (OV) ........................................................................................................................... 7
Line Feed Forward with DCMAX Reduction .............................................................................................................. 7
Remote ON/OFF .................................................................................................................................................... 7
Synchronization ...................................................................................................................................................... 8
Soft-Start ................................................................................................................................................................ 8
Shutdown/Auto-Restart .......................................................................................................................................... 8
Hysteretic Over-Temperature Protection ................................................................................................................ 8
Bandgap Reference ................................................................................................................................................ 8
High-Voltage Bias Current Source .......................................................................................................................... 8
Using Feature Pins ...................................................................................................................................................... 9
FREQUENCY (F) Pin Operation ............................................................................................................................. 9
LINE-SENSE (L) Pin Operation .............................................................................................................................. 9
EXTERNAL CURRENT LIMIT (X) Pin Operation ................................................................................................... 9
Typical Uses of FREQUENCY (F) Pin ...................................................................................................................... 12
Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins ....................................................... 12
Application Examples ............................................................................................................................................... 15
Key Application Considerations .............................................................................................................................. 17
DPA-Switch Design Considerations ...................................................................................................................... 17
DPA-Switch Layout Considerations ...................................................................................................................... 18
Quick Design Checklist ......................................................................................................................................... 19
Design Tools ......................................................................................................................................................... 19
Product Specifications and Test Conditions .......................................................................................................... 21
Typical Performance Characteristics ..................................................................................................................... 27
Part Ordering Information ........................................................................................................................................ 31
Package Outlines ...................................................................................................................................................... 32
2
K
1/04
DPA423-426
VC
0
DRAIN (D)
CONTROL (C)
ZC
INTERNAL
SUPPLY
1
SHUNT REGULATOR/
ERROR AMPLIFIER
+
SOFT START
5.8 V
4.8 V
-
-
5.8 V
+
INTERNAL UV
COMPARATOR
IFB
VI (LIMIT)
CURRENT
LIMIT
ADJUST
SOFT
START
+
VBG + VT
SHUTDOWN/
AUTO-RESTART
EXTERNAL
CURRENT LIMIT (X)
1V
VBG
OV/UV
LINE
SENSE
DCMAX
CONTROLLED
TURN-ON
GATE DRIVER
STOP SOFTSTART
DMAX
DCMAX
CLOCK
300/400 kHz
FREQUENCY (F)
CURRENT LIMIT
COMPARATOR
HYSTERETIC
THERMAL
SHUTDOWN
STOP LOGIC
LINE-SENSE (L)
-
÷8
ON/OFF
SAW
S
+
OSCILLATOR
Q
LEADING
EDGE
BLANKING
R
PWM
COMPARATOR
RE
CYCLE
SKIPPING
SOURCE (S)
PI-2760-070501
PI-2760-070501
Figure 2. Functional Block Diagram.
Pin Functional Description
DRAIN (D) Pin:
High voltage power MOSFET drain output. The internal startup
bias current is drawn from this pin through a switched highvoltage current source. Internal current limit sense point for
drain current.
CONTROL (C) Pin:
Error amplifier and feedback current input pin for duty cycle
control. Internal shunt regulator connection to provide internal
bias current during normal operation. It is also used as the
connection point for the supply bypass and auto-restart/
compensation capacitor.
LINE-SENSE (L) Pin:
Input pin for overvoltage (OV), under-voltage (UV) lock out,
line feed forward with the maximum duty cycle (DCMAX)
reduction, remote ON/OFF and synchronization. A connection
to SOURCE pin disables all functions on this pin.
EXTERNAL CURRENT LIMIT (X) Pin:
Input pin for external current limit adjustment and remote
ON/OFF. A connection to SOURCE pin disables all functions
on this pin.
FREQUENCY (F) Pin:
Input pin for selecting switching frequency: 400 kHz if connected
to SOURCE pin and 300 kHz if connected to CONTROL pin.
SOURCE (S) Pin:
Output MOSFET source connection for the power return.
Primary side control circuit common and reference point.
P Package (DIP-8)
G Package (SMD-8)
C
1
5
S
L
2
6
S
X
3
7
D
F
4
8
S
R Package
(TO-263-7C)
123 4 5
CL X S F
Tab Internally Connected to
SOURCE Pin (See layout considerations)
7
D
PI-3822-012104
Figure 3. Pin Configuration (top view).
K
1/04
3
DPA423-426
DPA-Switch Family Functional
Description
In addition to the standard TOPSwitch features, such as the
high-voltage start-up, the cycle-by-cycle current limiting, loop
compensation circuitry, auto-restart and thermal shutdown,
DPA-Switch also offers many advanced features that reduce
system cost and increase power supply performance and design
flexibility. Following is a summary of the advanced features:
1.
A fully integrated 5 ms soft-start limits peak currents and
voltages during start-up and reduces or eliminates output
overshoot in most applications.
2. A 75% maximum duty cycle (DCMAX) together with the
line feed forward with DCMAX reduction feature makes
DPA-Switch well suited for both flyback and forward
topologies.
3. High switching frequency (400 kHz/300 kHz, pin selectable)
allows the use of smaller size transformers and offers high
bandwidth for power supply control loop.
4. Cycle skipping operation at light load minimizes standby
power consumption (typically <10 mA input current).
5. Line under-voltage ensures glitch free operations at both
power-up and power-down and is tightly toleranced over
process and temperature to meet system level requirements
common in DC to DC converters (e.g. ETSI).
6. Line overvoltage protects DPA-Switch against excessive
input voltage and line surge.
7. External current limit adjustment allows the setting of the
current limit externally to a lower level near the operating
peak current and, if desired, further adjusts the level
gradually as line voltage rises. This makes possible an ideal
implementation of overload power limiting.
8. Synchronization function allows the synchronization of
DPA-Switch operation to an external lower frequency.
9. Remote ON/OFF feature permits DPA-Switch based power
supplies to be easily switched on/off using logic signals.
Maximum input current consumption is 2 mA in Remote
OFF.
10. Hysteretic over-temperature shutdown provides automatic
recovery from thermal fault.
11. Tight absolute tolerances and small temperature variations
on switching frequency, current limit, and under-voltage
lock out threshold (UV).
4
K
1/04
IB
75
Duty Cycle (%)
DPA-Switch is an integrated switched mode power supply chip
that converts a current at the control input to a duty cycle at the
open drain output of a high voltage power MOSFET. During
normal operation the duty cycle of the power MOSFET decreases
linearly with increasing CONTROL pin current as shown in
Figure 4. A patented high-voltage CMOS technology allows
both the high-voltage power MOSFET and all the low voltage
control circuitry to be cost effectively integrated onto a single
monolithic chip.
Auto-restart
ICD1
Slope = PWM Gain
42
IL < IL(DC)
4
I
C (SKIP)
IL = 115 µA
IC (mA)
PI-2761-112102
Figure 4. Relationship of Duty Cycle to CONTROL Pin Current.
Three pins, LINE-SENSE (L), EXTERNAL CURRENT LIMIT
(X) and FREQUENCY (F), are used to implement all the pin
controllable features. A resistor from the LINE-SENSE pin to
DC input bus implements line UV, line OV and line feed
forward with DCMAX reduction. A resistor from the EXTERNAL
CURRENT LIMIT pin to the SOURCE pin sets current limit
externally. In addition, remote ON/OFF may be implemented
through either the LINE-SENSE pin or the EXTERNAL
CURRENT LIMIT pin depending on the polarity of the logic
signal available as well as other system specific considerations.
Shorting both the LINE-SENSE and the EXTERNAL
CURRENT LIMIT pins to the SOURCE pin disables line OV,
line UV, line feed forward with DCMAX reduction, external
current limit, remote ON/OFF and synchronization. The
FREQUENCY pin sets the switching frequency to 400 kHz if
connected to the SOURCE pin, or 300 kHz if connected to the
CONTROL pin. This pin should not be left open. Please refer
to “Using Feature Pins” section for detailed information
regarding the proper use of those pins.
CONTROL Pin Operation
The CONTROL pin is a low impedance node that is capable of
receiving a combined supply and feedback current. During
normal operation, a shunt regulator is used to separate the
feedback signal from the supply current. CONTROL pin
voltage VC is the supply voltage for the control circuitry
including the MOSFET gate driver. An external bypass capacitor
closely connected between the CONTROL and SOURCE pins
is required to supply the instantaneous gate drive current. The
total amount of capacitance connected to this pin also sets the
auto-restart timing as well as control loop compensation.
When the DC input voltage is applied to the DRAIN pin during
start-up, the MOSFET is initially off, and the CONTROL pin
capacitor is charged through the switched high voltage current
source connected internally between the DRAIN and
CONTROL pins. When the CONTROL pin voltage VC reaches
DPA423-426
approximately 5.8 V, the control circuitry is activated and the
soft-start begins. The soft-start circuit gradually increases the
duty cycle of the MOSFET from zero to the maximum value
over approximately 5 ms. The high voltage current source is
turned off at the end of the soft-start. If no external feedback/
supply current is fed into the CONTROL pin by the end of the
soft-start, the CONTROL pin will start discharging in response
to the supply current drawn by the control circuitry and the gate
current of the switching MOSFET driver. If the power supply
is designed properly, and no fault condition such as open loop
or overloaded output exists, the feedback loop will close,
providing external CONTROL pin current, before the
CONTROL pin voltage has had a chance to discharge to the
lower threshold voltage of approximately 4.8 V (internal supply
under-voltage lockout threshold). When the externally fed
current charges the CONTROL pin to the shunt regulator
voltage of 5.8 V, current in excess of the consumption of the
chip is shunted to SOURCE through resistor RE as shown in
Figure 2. This current flowing through RE controls the duty
cycle of the power MOSFET to provide closed loop regulation.
The shunt regulator has a finite low output impedance ZC that
sets the gain of the error amplifier when used in a primary
feedback configuration. The dynamic impedance ZC of the
CONTROL pin together with the external CONTROL pin
capacitance sets the dominant pole for the control loop.
current standby mode. The high-voltage current source turns on
and charges the external capacitance again. A hysteretic
internal supply under-voltage comparator keeps VC within a
window of typically 4.8 to 5.8 V by turning the high-voltage
current source on and off as shown in Figure 5. The auto-restart
circuit has a divide-by-8 counter that prevents the output
MOSFET from turning on again until eight discharge/charge
cycles have elapsed. This is accomplished by enabling the
output MOSFET only when the divide-by-8 counter reaches
full count (S7). The counter effectively limits DPA-Switch
power dissipation as well as the maximum power delivered to
the power supply output by reducing the auto-restart duty cycle
to typically 4%. Auto-restart mode continues until output
voltage regulation is again achieved through closure of the
feedback loop.
Oscillator and Switching Frequency
The internal oscillator linearly charges and discharges an internal
capacitance between two voltage levels to create a sawtooth
waveform for the pulse width modulator. The oscillator sets
both the pulse width modulator latch and the current limit latch
at the beginning of each cycle.
The nominal switching frequency of 400 kHz was chosen to
minimize the transformer size and to allow faster power supply
loop response. The FREQUENCY pin, when shorted to the
CONTROL pin, lowers the switching frequency to 300 kHz,
which may be preferable in some applications such as those
employing secondary synchronous rectification. Otherwise,
the FREQUENCY pin should be connected to the SOURCE pin
for the default 400 kHz.
When a fault condition such as an open loop or overloaded
output prevents the flow of an external current into the
CONTROL pin, the capacitor on the CONTROL pin discharges
towards 4.8 V. At 4.8 V auto-restart is activated which turns the
output MOSFET off and puts the control circuitry in a low
~
~
~
~
VUV
~
~
VLINE
0V
S6
S7
S0
S1
S2
S6
S0
S7
S1
S2
~
~
S2
S6
S7
S7
5.8 V
4.8 V
~
~
~
~
0V
S1
~
~
S0
~
~
S7
VC
~
~
VDRAIN
0V
VOUT
1
2
~
~
~
~
~
~
0V
3
2
Note: S0 through S7 are the output states of the auto-restart counter
4
PI-2545-050602
Figure 5. Typical Waveforms for (1) Power Up (2) Normal Operation (3) Auto-restart (4) Power Down.
K
1/04
5
DPA423-426
Pulse Width Modulator and Maximum Duty Cycle
The pulse width modulator implements voltage mode control
by driving the output MOSFET with a duty cycle inversely
proportional to the current into the CONTROL pin that is in
excess of the internal supply current of the chip (see Figure 4).
The excess current is the feedback error signal that appears
across RE (see Figure 2). This signal is filtered by an RC network
with a typical corner frequency of 30 kHz to reduce the effect
of switching noise in the chip supply current generated by the
MOSFET gate driver. The filtered error signal is compared with
the internal oscillator sawtooth waveform to generate the duty
cycle waveform. As the control current increases, the duty cycle
decreases. A clock signal from the oscillator sets a latch that
turns on the output MOSFET. The pulse width modulator resets
the latch, turning off the output MOSFET. Note that a minimum
current must be driven into the CONTROL pin before the duty
cycle begins to change.
The maximum duty cycle, DCMAX is set at a default maximum
value of 75% (typical). However, by connecting the
LINE-SENSE to the DC input bus through a resistor with
appropriate value, the maximum duty cycle can be made to
decrease from 75% to 33% (typical) as shown in
Figure 7 when input line voltage increases (see line feed
forward with DCMAX reduction).
Minimum Duty Cycle and Cycle Skipping
To maintain power supply output regulation, the pulse width
modulator reduces duty cycle as the load at the power supply
output decreases. This reduction in duty cycle is proportional to
the current flowing into the CONTROL pin. As the CONTROL
pin current increases, the duty cycle reduces linearly towards a
minimum value specified as minimum duty cycle, DCMIN. After
reaching DCMIN, if CONTROL pin current is increased further
by approximately 2 mA, the pulse width modulator will force
the duty cycle from DCMIN to zero in a discrete step (refer to
Figure 4). This feature allows a power supply to operate in a
cycle skipping mode when the load consumes less power than
the DPA-Switch delivers at minimum duty cycle, DCMIN. No
additional control is needed for the transition between normal
operation and cycle skipping. As the load increases or decreases,
the power supply automatically switches between normal and
cycle skipping mode as necessary.
Cycle skipping may be avoided, if so desired, by connecting a
minimum load at the power supply output such that the duty
cycle remains at a level higher than DCMIN at all times.
Error Amplifier
The shunt regulator can also perform the function of an error
amplifier in primary side feedback applications. The shunt
regulator voltage is accurately derived from a temperaturecompensated bandgap reference. The gain of the error amplifier
is set by the CONTROL pin dynamic impedance. The
CONTROL pin clamps external circuit signals to the VC voltage
6
K
1/04
level. The CONTROL pin current in excess of the supply
current is separated by the shunt regulator and flows through RE
as a voltage error signal.
On-chip Current Limit with External Programmability
The cycle-by-cycle peak drain current limit circuit uses the
output MOSFET ON-resistance as a sense resistor. A current
limit comparator compares the output MOSFET on-state drain
to source voltage, VDS(ON) with a threshold voltage. At the
current limit, VDS(ON) exceeds the threshold voltage and the
MOSFET is turned off until the start of the next clock cycle. The
current limit comparator threshold voltage is temperature
compensated to minimize the variation of the current limit due
to temperature related changes in RDS(ON) of the output MOSFET.
The default current limit of DPA-Switch is preset internally.
However, with a resistor connected between EXTERNAL
CURRENT LIMIT pin and SOURCE pin, the current limit can
be programmed externally to a lower level between 25% and
100% of the default current limit. Please refer to the graphs in
the Typical Performance Characteristics section for the
selection of the resistor value. By setting current limit low, a
larger DPA-Switch than necessary for the power required can be
used to take advantage of the lower RDS(ON) for higher efficiency/
smaller heat sinking requirements. With a second resistor
connected between the EXTERNAL CURRENT LIMIT pin
and the DC input bus, the current limit is reduced with increasing
line voltage, allowing a true power limiting operation against
line variation to be implemented in a flyback configuration.
The leading edge blanking circuit inhibits the current limit
comparator for a short time after the output MOSFET is turned
on. The leading edge blanking time has been set so that, if a
power supply is designed properly, current spikes caused by
primary-side capacitance and secondary-side rectifier reverse
recovery time should not cause premature termination of the
switching pulse.
The current limit after the leading edge blanking time is as
shown in Figure 31. To avoid triggering the current limit in
normal operation, the drain current waveform should stay
within the envelope shown.
Line Under-Voltage Detection (UV)
At power up, UV keeps DPA-Switch off until the input line
voltage reaches the under voltage upper threshold. At power
down, UV holds DPA-Switch on until the input voltage falls
below the under voltage lower threshold. A single resistor
connected from the LINE-SENSE pin to the DC input bus sets
UV upper and lower thresholds. To avoid false triggering by
noise, a hysteresis is implemented which sets the UV lower
threshold typically at 94% of the UV upper threshold. If the UV
lower threshold is reached during operation without the power
supply losing regulation and the condition stays longer than
10 µs (typical), the device will turn off and stay off until the UV
upper threshold has been reached again. Then, a soft-start
DPA423-426
will be initiated the next time CONTROL pin voltage reaches
5.8.V. If the power supply loses regulation before reaching the
UV lower threshold, the device will enter auto-restart. At the
end of each auto-restart cycle (S7), the UV comparator is
enabled. If the UV upper threshold is not exceeded the MOSFET
will be disabled during the next cycle (see Figure 5). The UV
feature can be disabled independent of OV feature.
DPA-Switch is not restricted by this feature under normal
operation.
Remote ON/OFF
Remote ON/OFF control describes operation where the IC is
turned on or off for long periods as opposed to the cycle-bycycle on/off control which is described in the Synchronization
section below.
Line Overvoltage Shutdown (OV)
The same resistor used for UV also sets an over voltage
threshold which, once exceeded, will force the DPA-Switch
output into the off-state within one switching cycle. The ratio of
OV and UV thresholds is preset at 2.7 as can be seen in
Figure 7. When the MOSFET is off, the input voltage surge
capability is increased to the voltage rating of the MOSFET
(220 V), due to the absence of the reflected voltage and leakage
spikes on the drain. A small amount of hysteresis is provided on
the OV threshold to prevent noise triggering. The OV feature
can be disabled independent of the UV feature as shown in
Figure 13.
DPA-Switch can be turned on or off by controlling the current
into the LINE-SENSE pin or out from the EXTERNAL
CURRENT LIMIT pin (see Figure 7). This allows easy
implementation of remote ON/OFF control of DPA-Switch in
several different ways. A transistor or an optocoupler output
connected between the EXTERNAL CURRENT LIMIT pin
and the SOURCE pin implements this function with “activeon” (Figures 17, 19 and 21) while a transistor or an optocoupler
output connected between the LINE-SENSE pin and the
CONTROL pin implements the function with “active-off”
(Figures 18, 20 and 22).
Line Feed Forward with DCMAX Reduction
The same resistor used for UV and OV also implements line
voltage feed forward that minimizes output line ripple and
reduces power supply output sensitivity to line transients. This
feed forward operation is illustrated in Figure 4 by the different
values of IL. Note that for the same CONTROL pin current,
higher line voltage results in smaller operating duty cycle. As
an added feature, the maximum duty cycle DCMAX is also
reduced from 75% (typical) at a voltage slightly higher than the
UV threshold to 33% (typical) at the OV threshold
(see Figures 4, 7). Limiting DCMAX at higher line voltages helps
prevent transformer saturation due to large load transients in
forward converter applications. DCMAX of 33% at the OV
threshold was chosen to ensure that the power capability of the
When a signal is received at the LINE-SENSE pin or the
EXTERNAL CURRENT LIMIT pin to disable the output
through any of the pin functions such as OV, UV and remote
ON/OFF, DPA-Switch always completes its current switching
cycle before the output is forced off. The internal oscillator is
stopped at the end of the current cycle and stays there as long as
the disable signal exists. When the signal at the above pins
changes state from disable to enable, the internal oscillator
starts the next switching cycle.
The remote ON/OFF feature can be used as a standby or power
switch to turn off the DPA-Switch and keep it in a very low
power consumption state for indefinitely long periods. If the
DPA-Switch is held in remote-off state for longer than 10 µs
fSYNC ≥ 128 kHz; tOFF ≤ 7.7 µs; 120 ns ≤ tON ≤ 2250 ns for fOSC = 400 kHz
≤ 3080 ns for fOSC = 300 kHz
Oscillator
(SAW)
DMAX
VL
2V
Time
0V
tON
tOFF
ON
OFF
SYNC
PI-2762-070501
Figure 6. Synchronization Timing Diagram.
K
1/04
7
DPA423-426
(typical), the CONTROL pin goes into the hysteretic mode of
operation. In this mode, the CONTROL pin goes through
alternate charge and discharge cycles between 4.8 V and 5.8 V
(see CONTROL Pin Operation section above) and the IC runs
entirely off the high voltage DC input, but with very low power
consumption (30 mW typical at 48 V with LINE-SENSE and
EXTERNAL CURRENT LIMIT pins open). When the
DPA-Switch is remotely turned on after entering this mode, it
will initiate a normal start-up sequence with soft-start the next
time the CONTROL pin reaches 5.8 V. In the worst case, the
delay from remote on to start-up can be equal to the full
discharge/charge cycle time of the CONTROL pin, which is
approximately 36 ms for a 22 µF CONTROL pin capacitor.
This reduced-consumption remote-off mode can eliminate
expensive and unreliable in-line mechanical switches. It also
allows for microprocessor-controlled turn-on and turn-off
sequences that may be required in certain applications.
Synchronization
In addition to sensing incoming current for OV, UV and remote
ON/OFF, the LINE-SENSE pin also monitors its pin voltage
through a 1 V threshold comparator. A pin voltage below 1 V
turns on DPA-Switch. When the voltage at LINE-SENSE pin
rises beyond 1 V to disable the output, DPA-Switch completes
its current switching cycle before the output is forced off
(similar to remote ON/OFF operation). The internal oscillator
is stopped at the end of the current cycle awaiting the
LINE-SENSE pin voltage to go low to start the next cycle. This
allows the use of the 1 V threshold to synchronize DPA-Switch
to an external signal with a frequency lower than its internal
switching frequency. A transistor or an optocoupler output
connected between the LINE-SENSE pin and the SOURCE pin
implements this function (see Figure 24). Please refer to
Figure 6 for the timing waveforms of synchronization operation.
In order to be recognized as a synchronization pulse, the
LINE-SENSE pin needs to stay low (on-time) for at least
120 ns but no more than 2250 ns for 400 kHz (or 3080 ns for
300 kHz) internal switching frequency. In addition, the off-time
must be kept below 7.7 µs which is a limitation set by the lowest
synchronization frequency of 128 kHz allowed by the chip. The
effective DCMAX for synchronization operation can be calculated
as 0.75 x fSYNC/fOSC. An off-time longer than 7.7 µs may force the
CONTROL pin to go into the hysteretic mode and initiate a softstart cycle at next turn-on.
Soft-Start
Two on-chip soft-start functions are activated at start-up with a
duration of 5 ms (typical). Maximum duty cycle starts from 0%
and linearly increases to the default maximum of 75% at the end
of the 5 ms duration and the current limit starts from about 85%
and linearly increases to 100% at the end of the 5 ms duration.
In addition to start-up, soft-start is also activated at each restart
attempt during auto-restart and when restarting after being in
8
K
1/04
hysteretic regulation of CONTROL pin voltage (VC), due to
remote off or thermal shutdown conditions. This effectively
minimizes current and voltage stresses on the output MOSFET,
the clamp circuit and the output rectifier during start-up. This
feature also helps minimize output overshoot and prevents
saturation of the transformer during start-up.
Shutdown/Auto-Restart
To minimize DPA-Switch power dissipation under fault
conditions, the shutdown/auto-restart circuit turns the power
supply on and off at an auto-restart duty cycle of typically 4%
if an out of regulation condition persists. Loss of regulation
interrupts the external current into the CONTROL pin. VC
regulation changes from shunt mode to the hysteretic autorestart mode as described in CONTROL pin operation section.
When the fault condition is removed, the power supply output
becomes regulated, VC regulation returns to shunt mode, and
normal operation of the power supply resumes.
Hysteretic Over-Temperature Protection
Over temperature protection is provided by a precision analog
circuit that turns the output MOSFET off when the junction
temperature exceeds the thermal shutdown temperature
(137 °C typical). When the junction temperature cools to below
the hysteretic temperature (110 °C typical), normal operation
resumes providing automatic recovery. VC is regulated in
hysteretic mode and a 4.8 V to 5.8 V (typical) sawtooth
waveform is present on the CONTROL pin while in thermal
shutdown.
Bandgap Reference
All critical DPA-Switch internal voltages are derived from a
temperature-compensated bandgap reference. This reference is
also used to generate a temperature-compensated current
reference that is trimmed to accurately set the switching
frequency, current limit, and the line OV/UV thresholds.
DPA-Switch has improved circuitry to maintain all of the above
critical parameters within very tight absolute and temperature
tolerances.
High-Voltage Bias Current Source
This current source biases DPA-Switch from the DRAIN pin
and charges the CONTROL pin external capacitance during
start-up or hysteretic operation. Hysteretic operation occurs
during auto-restart, remote off and over-temperature shutdown.
In this mode of operation, the current source is switched on and
off with an effective duty cycle of approximately 20%. This
duty cycle is determined by the ratio of CONTROL pin charge
(IC(CH)) and discharge currents (ICD1 and ICD2). This current
source is turned off during normal operation when the output
MOSFET is switching. The effect of the current source switching
may be seen on the DRAIN voltage waveform as small
disturbances which is normal.
DPA423-426
SOURCE pin to generate synchronization pulse. Each time the
MOSFET turns on, the falling edge of the LINE-SENSE pin
voltage initiates a new switching cycle. The lowest
synchronization frequency guaranteed by DPA-Switch is
128 kHz. Refer to Table 2 for possible combinations of the
functions with example circuits shown in Figure 11 through
Figure 24. A description of specific functions in terms of the
LINE-SENSE pin I/V characteristic is shown in Figure 7 (right
hand side). The horizontal axis represents LINE-SENSE pin
current with positive polarity indicating currents flowing into
the pin. The meaning of the vertical axes varies with functions.
For those that control the on/off states of the output such as UV,
OV and remote ON/OFF, the vertical axis represents the enable/
disable states of the output. UV triggers at IUV (+50 µA typical
with 4 µA hysteresis) and OV triggers at IOV (+135 µA typical
with 4 µA hysteresis). Between the UV and OV thresholds, the
output is enabled. For line feed forward with DCMAX reduction,
the vertical axis represents the magnitude of the DCMAX Line feed
forward with DCMAX reduction lowers maximum duty cycle from
75% at IL(DC) (+55 µA typical) to 33% at IOV (+135 µA).
Using Feature Pins
FREQUENCY (F) Pin Operation
The FREQUENCY pin is a digital input pin. Shorting the
FREQUENCY pin to SOURCE pin selects the nominal
switching frequency of 400 kHz (Figure 9) which is suited for
most applications. For other applications that may benefit from
lower switching frequency, a 300 kHz switching frequency can
be selected by shorting the FREQUENCY pin to the CONTROL
pin (Figure 10). This pin should not be left open.
LINE-SENSE (L) Pin Operation
When current is fed into the LINE-SENSE pin, it works as a
voltage source of approximately 2.6 V up to a maximum current
of +240 µA (typical). At +240 µA, this pin turns into a constant
current sink. Refer to Figure 8. In addition, a comparator with
a threshold of 1 V is connected at the pin and is used to detect
when the pin is shorted to the SOURCE pin.
There are a total of five functions available through the use of
the LINE-SENSE pin: OV, UV, line feed forward with DCMAX
reduction, remote ON/OFF and synchronization. Shorting the
LINE-SENSE pin to the SOURCE pin disables all five functions.
The LINE-SENSE pin is typically used for line sensing by
connecting a resistor from this pin to the positive input DC
voltage bus to implement OV, UV and line feed forward with
DCMAX reduction over line voltage. In this mode, the value of the
resistor determines the line OV/UV thresholds, and the DCMAX
is reduced linearly with input DC high voltage starting from just
above the UV threshold. This pin can also be used as the input
pin for remote ON/OFF and synchronization. An external
transistor placed between the LINE-SENSE pin and the
CONTROL pin realizes remote on/off via UV or OV threshold.
Synchronization is available by connecting an open drain
external MOSFET between the LINE-SENSE pin and the
EXTERNAL CURRENT LIMIT (X) Pin Operation
When current is drawn out of the EXTERNAL CURRENT
LIMIT pin, it works as a voltage source of approximately 1.3 V
up to a maximum current of -230 µA (typical). At -230 µA, it
turns into a constant current source (refer to Figure 8).
There are two functions available through the use of the
EXTERNAL CURRENT LIMIT pin: external current limit and
remote ON/OFF. Shorting the EXTERNAL CURRENT LIMIT
pin and SOURCE pin disables both functions. In high efficiency
applications, this pin can be used to reduce the current limit
externally to a value close to the operating peak current, by
connecting the pin to the SOURCE pin through a resistor. The
pin can also be used as a remote on/off control input. Table 2
LINE-SENSE AND EXTERNAL CURRENT LIMIT PIN TABLE*
▲
Figure Number
12
13
Under-Voltage
✔
✔
Overvoltage
✔
Line Feed Forward (DCMAX)
✔
Three Terminal Operation
11
14
15
Remote ON/OFF
17
18
19
20
21
22
23
✔
✔
✔
✔
✔
✔
✔
✔
✔
24
✔
✔
Overload Power Limiting
External Current Limit
16
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Synchronization
*This table is only a partial list of many LINE-SENSE and EXTERNAL CURRENT LIMIT pin configurations that are possible.
Table 2. Typical LINE-SENSE and EXTERNAL CURRENT LIMIT Pin Configurations.
K
1/04
9
DPA423-426
IUV(U)
IREM(U)
(Enabled)
IOV(U)
(Enabled)
Output
MOSFET
Switching
Output
MOSFET
Switching
(Disabled)
(Disabled)
ILIMIT (Default)
DCMAX (75%)
Current
Limit
Maximum
Duty Cycle
-21.5 µA
VBG + VTP
-25.5 µA
VBG
X Pin Voltage
-250
L Pin Voltage
-200
-150
-100
-50
0
0
X Pin Current (µA)
131 µA
135 µA
47 µA
50
100
150
200
250
L Pin Current (µA)
Note: These figures provide idealized functional characteristics with typical performance values. Please refer to the
parametric table and typical performance characteristics sections of the data sheet for measured data.
PI-2778-080801
Figure 7. LINE-SENSE and EXTERNAL CURRENT LIMIT Pin Characteristics.
shows several different ways of using this pin. See Figure 7 for
a description of the functions where the horizontal axis (left
hand side) represents the EXTERNAL CURRENT LIMIT pin
current. The meaning of the vertical axes varies with function.
For those that control the on/off states of the output such as
remote ON/OFF, the vertical axis represents the enable/disable
10
K
1/04
states of the output. For external current limit, the vertical axis
represents the magnitude of the ILIMIT. Please see graphs in the
Typical Performance Characteristics section for the current
limit programming range and the selection of the appropriate
resistor value.
DPA423-426
CONTROL Pin
DPA-Switch
230 µA
(Negative Current Sense - ON/OFF,
Current Limit Adjustment)
EXTERNAL CURRENT LIMIT (X)
VBG + VT
(Voltage Sense)
LINE-SENSE (L)
VBG
1V
(Positive Current Sense - Under-Voltage,
Overvoltage, ON/OFF Maximum Duty
Cycle Reduction)
240 µA
PI-2765-080801
Figure 8. LINE-SENSE (L), and EXTERNAL CURRENT LIMIT (X) Pin Input Simplified Schematic.
K
1/04
11
DPA423-426
Typical Uses of FREQUENCY (F) Pin
+
+
DC
Input
Voltage
DC
Input
Voltage
D
CONTROL
C
S
F
D
CONTROL
C
S
-
F
PI-2655-071700
PI-2654-071700
Figure 10. 300 kHz Frequency Operation.
Figure 9. 400 kHz Frequency Operation.
Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins
+
+
VUV = IUV x RLS + VL (I = I )
L
UV
VOV = IOV x RLS + VL (I = I )
L
C L X S F
RLS
D
DC
Input
Voltage
619 kΩ
1%
DC
Input
Voltage
L
D
C
S
For RLS = 619 kΩ
VUV = 33.3 V
VOV = 86.0 V
D
D
CONTROL
L
CONTROL
C
C
S
-
X
F
-
S
PI-2766-070901
Figure 11. Three Terminal Operation (LINE-SENSE and
EXTERNAL CURRENT LIMIT Features Disabled.
FREQUENCY Pin can be tied to SOURCE or
CONTROL Pin).
+
VUV = RLS x IUV +
VL (I = I )
576 kΩ
1%
L
RLS
DC
Input
Voltage
PI-2767-091302
Figure 12. Line-Sensing for Under-Voltage, Overvoltage and
Line Feed Forward.
+
590 kΩ
1%
UV
For Values Shown
VUV = 33.3 V
42.2 kΩ
1%
D
-
1N4148
L
CONTROL
C
S
-
Figure 13. Line-Sensing for Under-Voltage Only (Overvoltage
Disabled).
K
1/04
OV
1%
C
PI-2852-091302
12
L
30 kΩ
D
L
VOV = IOV x RLS +
VL (I = I )
For Values Shown
VOV = 86.2 V
RLS
DC
Input
Voltage
CONTROL
6.2 V
OV
S
PI-2853-091302
Figure 14. Line-Sensing for Overvoltage Only (Under-Voltage
Disabled). Maximum Duty Cycle will be reduced at
Low Line.
DPA423-426
Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins (cont.)
+
For RIL = 12 kΩ
ILIMIT = 64%
+
ILIMIT = 100% @ 36 VDC
ILIMIT = 64% @ 72 VDC
RLS
363 kΩ
For RIL = 25 kΩ
ILIMIT = 34%
DC
Input
Voltage
See Figure 34 for other
resistor values (RIL)
D
CONTROL
C
S
DC
Input
Voltage
D
CONTROL
C
S
X
X
RIL
RIL
4.2 kΩ
-
-
PI-2854-050602
PI-2836-011904
Figure 15. Externally Set Current Limit.
+
Figure 16. Current Limit Reduction with Line Voltage.
QR can be an optocoupler
output or can be replaced by
a manual switch.
QR can be an
optocoupler output or
can be replaced
by a manual switch.
+
QR
ON/OFF
RMC
47 kΩ
DC
Input
Voltage
DC
Input
Voltage
D
CONTROL
C
37.4 kΩ
L
D
CONTROL
S
C
X
ON/OFF
QR
47 KΩ
-
S
PI-2625-040501
Figure 18. Active-off Remote ON/OFF. Maximum Duty Cycle will
be reduced.
Figure 17. Active-on (Fail Safe) Remote ON/OFF.
+
DC
Input
Voltage
QR can be an optocoupler
output or can be replaced
by a MOSFET or manual
switch.
For RIL = 12 kΩ
ILIMIT = 64%
D
CONTROL
C
S
For RIL = 25 kΩ
ILIMIT = 34%
+
ON/OFF
47 kΩ
RMC
47 kΩ
37.4 kΩ
DC
Input
Voltage
L
D
CONTROL
C
S
QR
QR can be an
optocoupler output
or can be replaced
by a manual switch.
QR
ON/OFF
X
RIL
-
PI-2855-050602
For RIL = 12 kΩ
ILIMIT = 64%
For RIL = 25 kΩ
ILIMIT = 34%
X
RIL
-
PI-2856-072602
PI-2857-050602
Figure 19. Active-on Remote ON/OFF with Externally Set Current
Limit.
Figure 20. Active-off Remote ON/OFF with Externally Set Current
Limit.
K
1/04
13
DPA423-426
Typical Uses of LINE-SENSE (L) and EXTERNAL CURRENT LIMIT (X) Pins (cont.)
+
DCMAX@36 V = 75%
DCMAX@72 V = 42%
CONTROL
C
S
switch.
QR
For RIL = 12 kΩ
ILIMIT = 64%
For RLS = 619 kΩ
ON/OFF
QR can be an optocoupler
output or can be replaced
by a manual switch.
L
D
619 kΩ output or can be replaced
1%
by a MOSFET or manual
RLS
619 kΩ
1%
RLS
DC
Input
Voltage
QR can be an optocoupler
+
47 kΩ
DC
Input
Voltage
VUV = 33.3 V
VOV = 86.0 V
L
D
CONTROL
C
X
QR
RIL
ON/OFF
-
47 kΩ
-
S
PI-2859-050602
Figure 21. Active-on Remote ON/OFF with LINE-SENSE and
EXTERNAL CURRENT LIMIT.
+
For RLS = 619 kΩ
VUV = 33.3 V
619 KΩ
VOV = 86.0 V
RLS
DC
Input
Voltage
-
L
DCMAX@36 V = 75%
DCMAX@72 V = 42%
CONTROL
C
K
1/04
+
QR can be an optocoupler
output.
For timing requirements,
see Figure 6.
X
RIL
12 kΩ
DC
Input
Voltage
For RIL = 12 kΩ
ILIMIT = 64%
See Figure 34 for other
resistor values (RIL)
to select different ILIMIT
values
PI-2837-011904
Figure 23. Line-Sensing and Externally Set Current Limit.
14
Figure 22. Active-off Remote ON/OFF with LINE-SENSE.
1%
D
S
PI-2858-072602
D
L
CONTROL
C
S
QR
-
ON/OFF
47 kΩ
PI-2640-050602
Figure 24. Synchronization.
DPA423-426
Application Examples
+ VIN
36-75 VDC
C7
1 nF
1.5 kV
L1
1 µH
2.5 A
R14
10 Ω
R1
619 kΩ
1%
R15
10 Ω
R17
10 Ω
T1
R16
10 kΩ
CONTROL
S
VR1
SMBJ
150
X
C
R3
18.2 kΩ
1%
R4
1.0 Ω
C5
220 nF
C4
4.7 µF
20 V
U2
PC357N1T
U1
DPA425R
F
5 V, 6 A
D1
BAV
19WS
RTN
U2
R7
10 kΩ
R10
10.0 kΩ
1%
R5*
DPA-Switch
L
D2
Q1
Si4888
DY
D4
BAV19WS
C9*
D
C12
1 µF
10 V
C11
100 µF
10 V
C17
3300 pF
Q2
Si4888
DY
C1, C2 & C3
1 µF
100 V
VIN
C10
100 µF
10 V
L2
C6
68 µF
10 V
*Optional components
D3
BAV19WS
R6
150 Ω
C13
10 µF
10 V
U3
LM431AIM3
C16
100 nF
R12
5.1 Ω
R9
220 Ω
C14
1 µF
R11
10.0 kΩ
1%
PI-3472-051303
Figure 25. A High Efficiency 30 W, 5 V, Telecom Input DC-DC Converter.
High Efficiency 30 W Forward Converter
The circuit shown in Figure 25 is a typical implementation of a
single output DC-DC converter using DPA-Switch in a forward
configuration with synchronous rectification. This design
delivers 30 W at 5 V, from a 36 VDC to 75 VDC input with a
nominal efficiency at 48 VDC of 90% using the DPA425R.
By taking advantage of many of the built-in features of the
DPA-Switch, the design is greatly simplified compared to a
discrete implementation. Resistor R1 programs the input undervoltage and overvoltage thresholds to typically 33 V and 86 V
respectively. This resistor also linearly reduces the maximum
duty from the internal maximum of 75% at 36 V to 42% at
72 V to prevent core saturation during load transients at high
input voltages. The DPA-Switch internal thresholds are
toleranced and characterized so the designer can guarantee the
converter will begin operation at 36 V, necessary to meet ETSI
standards, without the cost of an external reference IC.
The current limit is externally set by resistor R3 to just above the
drain current level needed for maximum load regulation to limit
the maximum overload power of the converter. The externally
programmable current limit feature also allows a larger
DPA-Switch family member to be selected. Using the X pin, the
current limit can be adjusted to the same level. A large device
reduces conduction losses and improves efficiency without
requiring any other circuit changes. This has been used here to
replace the DPA424R with a DPA425R.
The selectable 300/400 kHz switching frequency is set to 300 kHz
by connecting the FREQUENCY (F) pin to CONTROL (C).
DRAIN voltage clamping is provided by VR1, which keeps the
peak DRAIN voltage within acceptable limits. Transformer
core reset is provided by the gate capacitance of Q1 with R17
in series. Optional reset capacitance C9 with R5 can be added
if necessary to supplement the gate capacitance of Q1.
The output of the transformer is rectified using MOSFETs to
provide synchronous rectification. The UV/OV function,
together with the turns ratio of the transformer, defines the
maximum MOSFET gate voltage, allowing the very simple
gate drive arrangement, without the need for drive windings or
a drive IC. During primary on-time, capacitor C17 couples
charge through resistor R15 to drive the gate of the forward
MOSFET, Q2. Capacitor C17 provides a DC isolated drive for
Q2, preventing gate overstress on Q1 during power down. The
time constant formed by R16 and C17 is selected to be much
longer than one switching cycle. Diode D4 resets the voltage
on capacitor C17 before the next switching cycle. During the
primary off-time, the diode D2 provides a conduction path for
the energy in inductor L2 while Q1 is still off. The transformer
K
1/04
15
DPA423-426
+VIN
36 - 57 VDC
1
T1
L1
1 µH, 2A
9, 10
J1-1
R1
1 MΩ
1%
D2
SL43
R2
619 kΩ
1%
2
3.3 V, 2 A
J2-1
C5
330 µF
6V
C7
330 µF
6V
C6
330 µF
6V
C9
1 µF
10 V
RTN
6, 7
36 - 57
VDC
4
C2
47 pF
200 V
J2-2
R5
100 Ω
3
D3
BAV19, SOD323
R6
51 Ω
5
C1
1 µF
100 V
VR1
SMAJ
150A
L
D
CONTROL
-VIN
X
F
R3
8.66 kΩ
1%
C3
0.1 µF
50 V
R8
34 kΩ
1%
C8
1 µF
50 V
DPA-Switch
U1
DPA423G
U2
PC357
C
S
R7
1 kΩ
C11
0.1 µF
R4
5.1 Ω
C4
22 µF
10 V
J1-2
C10
0.33 µF
U3
CAT431L,
SOT23
R9
20 kΩ
1%
PI-3806-012304
Figure 26. A Cost Effective 6.6 W, 3.3 V Flyback DC-DC Converter.
reset voltage on the secondary winding directly drives a positive
voltage on the gate of catch MOSFET, Q1. MOSFET Q1
provides a low loss conduction path for a substantial portion of
the primary off-time. An isolated auxiliary winding on L2,
rectified and filtered by D1 and C4, provides the bias supply for
the optocoupler transistor.Output regulation is achieved by
using secondary side voltage reference, U3. The resistor divider
formed by R10 and R11, together with the reference voltage,
determines the output voltage. Diode D3 and C13 form a softfinish network that, together with the internal duty cycle and
current limit soft-start of the DPA-Switch, prevent output
overshoot at start-up. Resistor R7 ensures that the soft-finish
capacitor is discharged quickly when the output falls out of
regulation.Control loop response is shaped by R6, C16, R12,
C14, R9, R4 and C5, providing a wide bandwidth and good
phase margin at gain crossover. Since the PWM control in
DPA-Switch is voltage mode, no slope compensation is required
for duty cycles above 50%.
Cost Effective 6.6 W Flyback Conveter
The DPA-Switch flyback power supply provides a cost effective
solution for high density PoE and VoIP DC-DC applications.
Figure 26 shows a typical implementation of a single output
flyback converter using the DPA423G. For applications that
require input to output isolation, this simple, low component
count design delivers 6.6 W at 3.3 V from a 36 VDC to 57 VDC
input with a nominal efficiency at 48 VDC of 80%.
Resistor R2 programs the input under-voltage and overvoltage
thresholds to 33 V and 86 V respectively. Resistors R1 and R3
16
K
1/04
program the internal device current limit. The addition of line
sense resistor R1 reduces the current limit with increasing input
voltage, preventing excessive overload output current. In this
design the overload output current varies less than ±2.5% across
the entire input voltage range. Controlling the current limit also
reduces secondary component stress and leakage inductance
spikes, allowing the use of a lower VRRM (30 V rather than 40 V)
Schottky output diode, D2.
The primary side Zener clamp VR1 ensures the peak drain
voltage is kept below the 220 V BVDSS rating of U1 under input
surge and overvoltage events. During normal operation, VR1
does not conduct and C2 is sufficient to limit the peak drain
voltage.
The primary bias winding provides CONTROL pin current
after start-up. Diode D3 rectifies the bias winding, while
components R5 and C8 reduce high frequency switching noise
and prevent peak charging of the bias voltage. Capacitor C3
provides local decoupling of U1 and should be physically close
to the CONTROL and SOURCE pins. Energy storage for startup and auto-restart timing is provided by C4.
The secondary is rectified by D2 and the Low ESR tantalum
output capacitors, C5-C7, minimizing switching ripple and
maximizing efficiency. A small footprint secondary output
choke L1 and ceramic output capacitor C9 are adequate to
reduce high frequency noise and ripple to below 35 mV peakpeak under full load conditions.
The output voltage is sensed by the voltage divider formed by
DPA423-426
resistors R8 and R9 and is fed to the low voltage 1.24 V
reference U3. Feedback compensation is provided by R6, R7
and C11 together with C4 and R4. Capacitor C10 provides a
soft-finish characteristic, preventing output overshoot during
start-up.
Key Application Considerations
DPA-Switch Design Considerations
Power Table
This section provides a description of the assumptions used to
generate the power tables (Tables 1 and 3 through 6) and
explains how to use the information provided by them.
All Power tables: Tables 1 and 3 through 6
• Maximum output power is limited by the device internal
current limit. This is the peak output power which could
become the continuous output power, provided adequate
heat sinking is used.
• Data assumes adequate heat sinking to keep the junction
temperature at or below 100 °C and worst case RDS(ON) at
TJ = 100 °C.
• The use of P and G packages are recommended for device
dissipation equal to or less than 1.5 W only due to package
thermal limitation. For device dissipation above 1.5 W, use
R package.
Forward power tables: Tables 1 (upper half), 3 and 4
• Output power figures are based on forward topology using
Schottky diode rectification. Up to 5% higher output power
is possible using synchronous rectification.
• Dissipation data assumes a diode loss representing 6% of the
total output power and combined loss in magnetic components
representing 6% of the total output power. DPA-Switch
losses are based on a ratio between conduction and switching
losses of approximately 3:1. These assumptions are typical
for a single 5 V output forward converter design using
Schottky rectification and adequately designed magnetic
components.
Flyback power tables: Tables 1 (lower half), 5 and 6
• Output power and dissipation figures are based on a 5 V
output using Schottky diode rectification with an efficiency
of 85%. Values are generated by calculation based on
I2 • RDS(ON) losses and characterization of switching losses,
correlated to bench measurement of each DPA-Switch device.
• Device dissipations above 1.5 W are possible using the
R package. However the forward converter topology is
recommended for such higher power designs.
The power tables provide two types of information. The first is
the expected device dissipation for a given output power. The
second is the maximum power output. Each table specifies the
input voltage range and assumes a single 5 V output using
Schottky diode rectification.
OUTPUT POWER TABLE
16-32 VDC RANGE (FORWARD)2
Total Device
Dissipation 0.5 W
PRODUCT3
1W
2.5 W 4 W
Max
Power
Output1
6W
5W 7W
7 W 10 W 15 W 10 W 14 W 22 W 27 W
12 W 16.5 W 25 W 31 W 37 W
DPA423
DPA424
DPA425
DPA426
7.5 W
15.5 W
31 W
43 W
Table 3. Output Power Table for 16 VDC Minimum Input Voltage.
Notes: 1. Maximum output power is limited by device internal
current limit. 2. See text in this section for a complete description of
assumptions. 3. See Part Ordering Information.
OUTPUT POWER TABLE
24-48 VDC RANGE (FORWARD)2
Total Device
Dissipation 0.5 W
PRODUCT3
8W
11 W
16 W
18 W
DPA423
DPA424
DPA425
DPA426
1W
2.5 W
4W
6W
Max
Power
Output1
11 W
- 11.5 W
16 W 23.5 W 25 W
22 W 35 W 43 W
47 W
25 W 39 W 48 W 58 W 65 W
Table 4. Output Power Table for 24 VDC Minimum Input Voltage
(See Table 3 for Notes).
OUTPUT POWER TABLE
16-32 VDC RANGE (FLYBACK)2
Total Device
Dissipation
0.5 W
0.75 W
1W
1.5 W
Max
Power
Output1
15 W
6W
11 W
22 W
PRODUCT3
DPA423
DPA424
DPA425
5W
6.5 W
7W
8.5 W 10 W
10 W 12 W
Table 5. Flyback Output Power Table for 16 VDC Minimum Input
Voltage (See Table 3 for Notes).
For example, referring to Table 1, for 36-75 VDC input range,
DPA424 would typically dissipate 1 W in a 23 W forward
converter and has a maximum power capacity of 35 W. In the
same converter, DPA425 would dissipate 0.5 W. Selecting
DPA425 with associated reduced dissipation would increase
overall converter efficiency by approximately 2%.
Issues Affecting Dissipation:
1) Using synchronous rectification will tend to reduce device
dissipation.
K
1/04
17
DPA423-426
OUTPUT POWER TABLE
24-48 VDC RANGE (FLYBACK)2
Total Device
Dissipation
0.5 W
0.75 W
1W
1.5 W
Max
Power
Output1
-
8.5 W
17 W
34 W
PRODUCT3
DPA423
DPA424
DPA425
7W
8.5 W 11.5 W 14 W
-4
-4
-4
Table 6. Flyback Output Power Table for 24 VDC Minimum Input
Voltage.
Notes: 1. Maximum output power is limited by device internal
current limit. 2. See text in this section for a complete description of
assumptions. 3. See Part Ordering Information. 4. Due to higher switching
losses, the DPA425 may not deliver additional power compared to a
smaller device.
2) Designs with lower output voltages and higher currents will
tend to increase the device dissipation listed in the power table.
3) Reduced input voltage decreases the available output power
for the same device dissipation. Tables 3 to 6 are the power
tables for 16 VDC and 24 VDC input voltages. Input voltages
below 16 V are possible, but since the internal start-up current
source is not specified at voltages below 16 V, an external chip
supply current should be fed into the CONTROL pin
approximately equal to but less than ICD1.
DPA-Switch Selection
Use Tables 1 and 3 through 6 to select the DPA-Switch based on
device dissipation. Selecting the optimum DPA-Switch depends
upon required maximum output power, efficiency, heat sinking
constraints and cost goals. With the option to externally reduce
current limit, a larger DPA-Switch may be used for lower power
applications where higher efficiency is needed or minimal heat
sinking is available. Generally, selecting the next larger device,
than is required for power delivery will give the highest efficiency.
Selecting even larger devices may give little or no improvement
in efficiency due to the improvement in conduction losses being
negated by larger device switching losses. Figure 50 provides
information on switching losses. This together with conduction
loss calculations give an estimate of device dissipation.
Primary Clamp
A primary clamp network is recommended to keep the peak
DRAIN voltage due to primary leakage inductance to below the
BVDSS specification. A Zener diode combined with a small value
capacitor connected across the primary winding is a low cost and
low part count implementation.
Output Rectification
Rectification of the secondary is typically performed using Schottky
diodes or synchronous rectification. Schottky diodes are selected
for peak inverse voltage, output current, forward drop and thermal
18
K
1/04
conditions. Synchronous rectification requires the additional
complication of providing gate drive. The specified line undervoltage and line overvoltage thresholds of DPA-Switch simplifies
deriving gate drive directly from the transformer secondary
winding for many applications. The turns ratio of the transformer
together with the under/over-voltage thresholds defines the
minimum and maximum gate voltages, removing the need for
Zeners to clamp the gate voltage.
Soft-Start
Generally a power supply experiences maximum stress at start-up
before the feedback loop achieves regulation. For a period of 5 ms
the on-chip soft-start linearly increases the duty cycle from zero to
the default DCMAX at turn-on. In addition, the primary current limit
increases from 85% to 100% over the same period. This causes
the output voltage to rise in an orderly manner allowing time for
the feedback loop to take control of the duty cycle. This integrated
soft-start reduces the stress on the DPA-Switch MOSFET, clamp
circuit and output diode(s), and helps prevent transformer saturation
during start-up. Also, soft-start limits the amount of output
voltage overshoot, and in many applications eliminates the need
for a soft-finish capacitor. If necessary, to remove output overshoot,
a soft-finish capacitor may be added to the secondary reference.
Switching Frequency
The FREQUENCY pin of DPA-Switch offers a switching
frequency option of 400 kHz or 300 kHz. Operating at 300 kHz
will increase the amount of magnetization energy stored in the
transformer. This is ideal for applications using synchronous
rectification driven directly from the transformer secondary where
this energy can be used to drive the catch MOSFET gate.
Transformer Design
It is recommended that the forward converter transformer be
designed for maximum operating flux swing of 1500 Gauss and
a peak flux density of 3500 Gauss. When operating at the
maximum current limit of the selected DPA-Switch (during
overload conditions), neither magnetic component (transformer
and output inductor) should be allowed to saturate. When a larger
device than necessary has been selected, reducing the internal
current limit close to the operating peak current limits overload
power and minimizes the size of the secondary components.
No-load and Standby Consumption
Cycle skipping operation at light or no load can significantly
reduce power loss. In addition this operating mode ensures that
the output maintains regulation even without an external minimum
load. However, if cycle skipping is undesirable in a particular
application, it can be avoided by adding sufficient pre-load.
DPA-Switch Layout Considerations
The DPA-Switch can operate with large DRAIN current, the
following guidelines should be carefully followed.
DPA423-426
Primary Side Connections
The tab of DPA-Switch R package is the intended return path for
the high switching currents. Therefore, the tab should be
connected by wide, low impedance traces back to the input
decoupling capacitor. The SOURCE pin should not be used to
return the power currents; incorrect operation of the device may
result. The SOURCE is only intended as a signal ground. The
device tab (SOURCE) is the correct connection for power
currents with the R package.
The CONTROL pin bypass capacitor should be located as
close as possible to the SOURCE and CONTROL pins and its
SOURCE connection trace should not be shared by the main
MOSFET switching currents. All SOURCE pin referenced
components connected to the LINE-SENSE or EXTERNAL
CURRENT LIMIT pins should also be located closely between
their respective pin and SOURCE. Once again, the SOURCE
connection trace of these components should not be shared by
the main MOSFET switching currents. It is critical that
the tab (SOURCE) power switching currents are returned to the
input capacitor through a separate trace that is not
shared by the components connected to CONTROL,
LINE-SENSE or EXTERNAL CURRENT LIMIT pins.
Any traces to the L or X pins should be kept as short as possible
and away from the DRAIN trace to prevent noise coupling.
LINE-SENSE resistor (R1 in Figure 25) should be located close
to the L pin to minimize the trace length on the L pin side.
In addition to the CONTROL pin capacitor (C6 in Figure 25),
a high frequency bypass capacitor in parallel is recommended
as close as possible between SOURCE and CONTROL pins for
better noise immunity. The feedback optocoupler output should
also be located close to the CONTROL and SOURCE pins of
DPA-Switch.
Heat Sinking
To maximize heat sinking of the DPA-Switch R or G package
and the other power components, special thermally conductive
PC board material (aluminum clad PC board) is recommended.
This has an aluminum sheet bonded to the PC board during the
manufacturing process to provide heat sinking directly and
allow the attachment of an external heat sink. If normal PC
board material is used (such as FR4), providing copper areas on
both sides of the board and using thicker copper will improve
heat sinking.
If an aluminum clad board is used then shielding of switching
nodes is recommended. This consists of an area of copper
placed directly underneath switching nodes such as the drain
node, and output diode to provide an electrostatic shield to
prevent coupling to the aluminum substrate. These areas are
connected to input negative in the case of the primary and output
return for secondary. This reduces the amount of capacitive
coupling into the insulated aluminum substrate that can then
appear on the output as ripple and high frequency noise.
Quick Design Checklist
As with any power supply design, all DPA-Switch designs
should be verified on the bench to make sure that component
specifications limits are not exceeded under worst case
conditions. The following minimum set of tests for DPA-Switch
forward converters is strongly recommended:
1. Maximum drain voltage – Verify that peak VDS does not
exceed minimum BVDSS at highest input voltage and
maximum overload output power. It is normal, however, to
have additional margin of approximately 25 V below BVDSS
to allow for other power supply component unit-to-unit
variations. Maximum overload output power occurs when
the output is loaded to a level just before the power supply
goes into auto-restart (loss of regulation).
2. Transformer reset margin – Drain voltage should also be
checked at highest input voltage with a severe load step (50100%) to verify adequate transformer reset margin. This test
shows the duty cycle at high input voltage, placing the most
demand on the transformer reset circuit.
3. Maximum drain current – At maximum ambient temperature,
maximum input voltage and maximum output load, verify
drain current waveforms at start-up for any signs of
transformer or output inductor saturation and excessive
leading edge current spikes. DPA-Switch has a leading edge
blanking time of 100 ns to prevent premature termination of
the on cycle. Verify that the leading edge current spike does
not extend beyond the blanking period.
4. Thermal check – At maximum output power, minimum
input voltage and maximum ambient temperature, verify
that temperature specifications are not exceeded for the
transformer, output diodes, output choke(s) and output
capacitors. The DPA-Switch is fully protected against overtemperature conditions by its thermal shutdown feature. It is
recommended that sufficient heat sinking is provided to
keep the tab temperature at or below 115 °C (R package),
SOURCE pins at or below 100 °C (P/G packages) under
worst case continuous load conditions (at low input voltage,
maximum ambient and full load). This provides adequate
margin to minimum thermal shutdown temperature
(130 °C) to account for part-to-part RDS(ON) variation. When
monitoring device temperatures, note that the junction-tocase thermal resistance should be accounted for when
estimating die temperature.
Design Tools
Up-to-date information on design tools is available at the Power
Integrations Web site: www.powerint.com.
K
1/04
19
DPA423-426
Solder Side
Component Side
TOP VIEW
Output
Diode
V
Transformer
+
D
Inductor
(Coupled)
V
DC
In
S
DPA-Switch
X
L
C
V
+
DC
Out
Optocoupler
-
-
V
Maximize hatched copper area for optimum heat sinking
V
Via between board layers
PI-2883-060602
Figure 27. Layout Considerations for DPA-Switch Using R Package.
Top Side PCB
Bottom Side PCB
TOP VIEW
Bottom Diode
Heatsink
(Two sided printed circuit board)
V
V
+
V
DC
In
V
-
-
S
S
D
S
V
DPA-Switch
C
L
X
F
T
r
a
n
s
f
o
r
m
e
r
V
V
V
+
DC
Out
V
V
V
PI-3805-012904
DPA-Switch Heatsink
V
Optocoupler
Maximize hatched copper area for optimum heat sinking
V
Via between board layers
Figure 28. Layout Considerations for DPA-Switch Using G Package.
20
K
1/04
DPA423-426
ABSOLUTE MAXIMUM RATINGS(1, 4)
DRAIN Voltage ............................................ -0.3 to 220 V
DRAIN Peak Current: DPA423 ............................... 1.75 A
DPA424 ................................. 3.5 A
DPA425 .................................... 7 A
DPA426 ................................. 9.6 A
CONTROL Voltage .......................................... -0.3 to 9 V
CONTROL Current ............................................... 100 mA
LINE SENSE Pin Voltage ................................ -0.3 to 9 V
EXTERNAL CURRENT LIMIT Pin Voltage .. -0.3 to 9 V
FREQUENCY Pin Voltage ............................... -0.3 to 9 V
Storage Temperature ..................................... -65 to 150 °C
Operating Junction Temperature (2) ............... -40 to 150 °C
Lead Temperature (3) ............................................... 260 °C
Notes:
1. All voltages referenced to SOURCE, TA = 25 °C.
2. Normally limited by internal circuitry.
3. 1/16" from case for 5 seconds.
4. Maximum ratings specified may be applied, one at a time,
without causing permanent damage to the product.
Exposure to Absolute Maximum Rating conditions for
extended periods of time may affect product reliability.
THERMAL IMPEDANCE
Thermal Impedance: P or G Package:
(θJA) ...................... 70 °C/W(1); 60 °C/W(2)
(θJC)(3) ......................................... 11 °C/W
R Package:
(θJA) ......................................... 40 °C/W(4)
............................................................................ 30 °C/W(5)
(θJC)(6) ........................................... 2 °C/W
Notes:
1. Soldered to 0.36 sq. in. (232 mm2), 2 oz. (610 g/m2) copper clad.
2. Soldered to 1 sq. in (645 mm2), 2 oz. (610 g/m2) copper clad.
3. Measured on pin 7 (SOURCE) close to plastic interface.
4. Soldered to 1 sq. inch (645 mm2), 2 oz. (610 g/m2) copper clad.
5. Soldered to 3 sq. inch (1935 mm2), 2 oz. (610 g/m2) copper clad.
6. Measured at the back surface of tab.
Conditions
Parameter
Symbol
(Unless Otherwise Specified)
See Figure 32
SOURCE = 0 V; TJ = -40 to 125 °C
Min
Typ
Max
375
400
425
282
300
317
4
6
Units
CONTROL FUNCTIONS
Switching
Frequency
Duty Cycle (Prior
to Cycle Skipping)
Maximum Duty
Cycle
Control Current at
Start of Cycle
Skipping
External Bias
Current
fOSC
TJ = 25 °C
FREQUENCY Pin
Connected to SOURCE
FREQUENCY Pin
Connected to CONTROL
kHz
DCMIN
DCMAX
IC(skip)
IB
IC = ICD1
VL = 0 V
71
75
79
IL = 80 µA
52
62
71
IL = 115 µA
32
42
57
DPA423
7.2
9.0
DPA424
8.2
10.0
DPA425
10.0
11.5
12.0
14.0
2
2.5
2.8
3.5
3.5
4.4
3.6
4.8
6.0
4.4
5.7
7.1
TJ = 25 °C; fOSC = 400 kHz
TJ = 25 °C; fOSC = 400 kHz
DPA426
DPA423
DPA424
DPA425
DPA426
%
%
mA
mA
K
1/04
21
DPA423-426
Conditions
Parameter
Symbol
(Unless Otherwise Specified)
See Figure 32
SOURCE = 0 V; TJ = -40 to 125 °C
Min
Typ
Max
Units
5
7.2
ms
-22
-18
%/mA
CONTROL FUNCTIONS (cont.)
Softstart Time
PWM Gain
tSOFT
TJ = 25 °C; DCMIN to DCMAX
DCreg
TJ = 25 °C; IC = (IC(skip) + IB)/2
PWM Gain
Temperature Drift
Dynamic
Impedance
-28
TJ = 25 °C; IC = (IC(skip) + IB)/2
ZC
%/mA/°C
-0.01
See Note A
10
Dynamic Impedance
Temperature Drift
CONTROL Pin
Internal Filter Pole
15
22
Ω
0.18
%/°C
30
kHz
SHUTDOWN/AUTO-RESTART
CONTROL Pin
Charging Current
IC(CH)
During Startup and Auto-Restart:
VC=5.0 V; VD=16 V & 40 V; TJ=25 °C
-5.2
-4
mA
Average Current at the Beginning of
Softstart:
VC=5.0 V; VD=16 V & 40 V; TJ=25 °C
-19
See Note A
-0.6
%/°C
5.8
V
Charging Current
Temperature Drift
Auto-restart Upper
Threshold Voltage
VC (AR)U
Auto-restart Lower
Threshold Voltage
VC (AR)L
4.5
4.8
Auto-restart
Hysteresis Voltage
VC(AR)Hyst
0.8
1
Auto-restart Duty
Cycle
Auto-restart
Frequency
-3
DC(AR)
CCONTROL = 22 µF; fOSC = 400 kHz;
VX = 0 V
f(AR)
CCONTROL = 22 µF; fOSC = 400 kHz;
VX = 0 V
5.1
V
V
10
%
Hz
3.8
LINE-SENSE (L) AND EXTERNAL CURRENT LIMIT (X) INPUTS
Line UnderVoltage Threshold
Current and
Hysteresis (L pin)
22
K
1/04
IUV
TJ = 25 °C
Threshold from Off to On
48
50
52
Threshold from On to Off
44.5
47
49.5
Hysteresis
2
3
µA
DPA423-426
Conditions
Parameter
Symbol
(Unless Otherwise Specified)
See Figure 32
SOURCE = 0 V; TJ = -40 to 125 °C
Min
Typ
Max
Units
LINE-SENSE (L) AND EXTERNAL CURRENT LIMIT (X) INPUTS (cont)
Line Overvoltage
or Remote ON/
OFF Threshold
Current and
Hysteresis (L pin)
Threshold from On to Off
IOV
Threshold from On to Off
IREM
L pin Short Circuit
Current
IL(SC)
X pin Short Circuit
Current
IX(SC)
L pin Voltage
(Positive Current)
VL
Maximum Duty
Cycle Reduction
Onset Threshold
Current
Remote OFF
DRAIN Supply
Current
L pin Voltage
Turn-On Threshold in Synchronous
Mode
ID(RMT)
Off-Time
Pulse Width for
Synchronization
toff(sync)
tdelay(sync)
-21.5
4.5
VD = 40 V
VX = 0 V
-16
µA
VL = VC
175
240
VL = 0 V
-230
-170
Normal Mode
-270
-230
-185
Remote OFF using L Pin
-105
-85
-65
IL = IUV
2.05
2.35
2.6
IL = IOV
2.1
2.5
2.9
IX = -50 µA
1.35
IX = -150 µA
1.25
TJ = 25 °C
55
380
µA
µA
V
µA
VL= Floating
0.6
1.1
VL=VC
0.9
1.5
1
1.4
mA
0.6
VL(TH)
ton(sync)
-27
Hysteresis
IL(DC)
µA
4
-25.5
VX = 0 V
149
131
TJ = 25 °C Threshold from Off to On
VX
On-Time
Pulse Width for
Synchronization
Synchronous Turn
On Delay
117
Hysteresis
Remote ON/OFF
Negative Threshold Current and
Hysteresis (X pin)
X pin Voltage
(Negative Current)
TJ = 25 °C Threshold from Off to On
135
V
fOSC = 400 kHz
120
2250
fOSC = 300 kHz
120
3080
0.25
7.7
µs
250
ns
From Synchronous On to Drain
Turn-On
ns
K
1/04
23
DPA423-426
Conditions
Parameter
Symbol
(Unless Otherwise Specified)
See Figure 32
SOURCE = 0 V; TJ = -40 to 125 °C
Min
Typ
Max
Units
4
V
FREQUENCY (F) INPUT
FREQUENCY Pin
Threshold Voltage
VF
FREQUENCY Pin
Input Current
IF
FREQUENCY Pin
Delay Time
tdelay(VF)
1.1
VF = 0 V
-0.38
VF = VC
17
µA
120
2
µs
CIRCUIT PROTECTION
Self Protection
Current Limit
(See Note B)
ILIMIT
TJ = 25 °C
DPA423 di/dt = 300 mA/µs
1.16
1.25
1.34
DPA424 di/dt = 600 mA/µs
2.32
2.50
2.68
DPA425 di/dt = 1.25 A/µs
4.65
5.00
5.35
DPA426 di/dt = 1.75 A/µs
6.50
7.00
7.50
Initial Current Limit
IINIT
VD = 35 V
Leading Edge
Blanking Time
tLEB
TJ = 25 °C
Current Limit Delay
tIL(D)
IC = (IC(skip) +IB)/2
Thermal Shutdown
Temperature
TJ(SD)
Thermal Shutdown
Hysteresis
TJ(SD)hyst
Power-up Reset
Threshold Voltage
VC(RESET)
A
0.9 x
ILIMIT(min)
A
100
100
130
137
ns
145
27
1.5
ns
°C
°C
2.75
4
1.30
2.00
1.50
2.30
0.65
0.75
1.00
0.33
0.50
0.24
0.37
1.15
0.38
0.58
0.28
0.43
V
OUTPUT
ON-State
Resistance
RDS(ON)
TJ = 100 °C
DPA424
ID = 600 mA
TJ = 25 °C
TJ = 100 °C
DPA425
ID = 1.25 A
TJ = 25 °C
TJ = 100 °C
TJ = 25 °C
TJ = 100 °C
DPA426
ID = 1.75 A
24
K
1/04
TJ = 25 °C
DPA423
ID = 300 mA
Ω
DPA423-426
Conditions
Parameter
Symbol
(Unless Otherwise Specified)
See Figure 32
SOURCE = 0 V; TJ = -40 to 125 °C
Min
Typ
Max
Units
65
130
260
360
µA
OUTPUT (cont)
OFF-State Drain
Leakage Current
Breakdown
Voltage
IDSS
BVDSS
DPA423
DPA424
DPA425
DPA426
VX, VL = Floating;
VD = 150 V;
TJ = 125 °C;
IC = (IC(skip) + IB)/2
VX, VL = Floating; TJ = 25 °C
IC = (IC(skip) + IB)/2; See Note C
220
V
Rise Time
tR
Measured in a Typical Application
10
ns
Fall Time
tF
Measured in a Typical Application
10
ns
SUPPLY VOLTAGE CHARACTERISTICS
DRAIN Supply
Voltage
Shunt Regulator
Voltage
VC(SHUNT)
Shunt Regulator
Temperature Drift
CONTROL
Supply/Discharge
Current
See Note D
16
IC = (IC(skip) + IB)/2; TJ = 25 °C
5.6
IC = (IC(skip) + IB)/2
lCD1
lCD2
Output
MOSFET Enabled
VL = 0 V;
fOSC = 400 kHz
DPA423
DPA424
DPA425
DPA426
Output MOSFET Disabled
VL = 0 V; fOSC = 400 kHz
V
5.85
6.0
±50
V
PPM/°C
1.9
2.6
3.7
4.8
2.3
3.0
4.3
5.4
2.7
3.4
4.8
6
0.4
0.73
1.2
mA
NOTES:
A. For specifications with negative values, a negative temperature coefficient corresponds to an increase in
magnitude with increasing temperature, and a positive temperature coefficient corresponds to a decrease in
magnitude with increasing temperature.
B. For externally adjusted current limit values, please refer to Figure 34 (Current Limit vs. External Current Limit
Resistance) in the Typical Performance Characteristics section.
C. Breakdown voltage may be checked against minimum BVDSS specification by ramping the DRAIN pin voltage up to
but not exceeding minimum BVDSS.
D. It is possible to start up and operate DPA-Switch at DRAIN voltages well below 16 V. However, the CONTROL
pin charging current is reduced, which affects start-up time, auto-restart frequency, and auto-restart duty cycle.
Refer to Figure 44, the characteristic graph on CONTROL pin charge current (IC) vs. DRAIN voltage for low
voltage operation characteristics.
K
1/04
25
DPA423-426
t2
t1
HV
90%
90%
DRAIN
VOLTAGE
t
D= 1
t2
10%
0V
PI-2039-033001
100
80
60
40
Dynamic
1
=
Impedance Slope
20
1.4
DRAIN Current (Normalized)
PI-2880-060302
CONTROL Pin Current (mA)
120
PI-2889-061302
Figure 29. Duty Cycle Measurement.
tLEB (Blanking Time) +
tIL(D) (Current Limit Delay)
1.2
1
0.8
0.6
0.4
Temperature Range:
-40 °C to 125 °C
0.2
0
0
0
2
4
6
8
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
10
Time (µs)
CONTROL Pin Voltage (V)
Figure 30. CONTROL Pin I-V Characteristic.
S1
Figure 31. Typical Drain Operation Current Envelope.
470 Ω
5W
0-200 kΩ
5-50 V
40 V
L
470 Ω
D
CONTROL
C
C
DPA-Switch
S2
S4
0-15 V
47 µF
0.1 µF
F
X
S
S3
0-70 kΩ
NOTE: This test circuit is not applicable for current limit or output characteristic measurements.
PI-2860-050602
Figure 32. DPA-Switch General Test Circuit.
26
K
1/04
DPA423-426
BENCH TEST PRECAUTIONS FOR EVALUATION OF ELECTRICAL CHARACTERISTICS
The following precautions should be followed when testing
DPA-Switch by itself outside of a power supply. The schematic
shown in Figure 32 is suggested for laboratory testing of
DPA-Switch.
restart mode, there is only a 12.5% chance that the CONTROL
pin oscillation will be in the correct state (drain active state) so
that the continuous drain voltage waveform may be observed.
It is recommended that the VC power supply be turned on first
and the DRAIN pin power supply second if continuous drain
voltage waveforms are to be observed. The 12.5% chance of
being in the correct state is due to the divide-by-8 counter.
Temporarily shorting the CONTROL pin to the SOURCE pin
will reset DPA-Switch, which then will come up in the correct
state.
When the DRAIN pin supply is turned on, the part will be in the
auto-restart mode. The CONTROL pin voltage will be oscillating
at a low frequency between 4.8 and 5.8 V and the drain is turned
on every eighth cycle of the CONTROL pin oscillation. If the
CONTROL pin power supply is turned on while in this auto-
1.1
PI-2838-032202
Current Limit
(Normalized to Internal Current Limit)
Typical Performance Characteristics
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
-230
-180
-130
-80
-30
0
IX (µA)
1.1
PI-2839-032202
Current Limit
(Normalized to Internal Current Limit)
Figure 33. Current Limit vs. EXTERNAL CURRENT LIMIT Pin Current.
1.0
0.9
Maximum
0.8
0.7
Minimum
0.6
0.5
Typical
0.4
0.3
0.2
0.1
0
5
10
15
20
25
30
35
External Current Limit Resistor RIL (kΩ)
Figure 34. Current Limit vs. External Current Limit Resistance.
K
1/04
27
DPA423-426
Typical Performance Characteristics (cont.)
0.8
0.6
0.4
0.2
PI-2866-051702
1.0
1.2
Current Limit
(Normalized to 25 °C)
PI-2868-051502
1.0
0.8
0.6
0.4
0.2
0
0
25
50
0
75 100 125 150
-50 -25
Junction Temperature (°C)
0.8
0.6
0.4
0.2
1.0
0.8
0.6
0.4
0.2
0
0
25
50
-50 -25
75 100 125 150
PI-2867-051502
Under-Voltage Threshold
(Normalized to 25 °C)
1.0
0.8
0.6
0.4
0.2
0
0
25
50
25
50
75 100 125 150
75 100 125 150
Junction Temperature (°C)
Figure 39. Under-Voltage Threshold vs. Temperature.
Figure 38. Overvoltage Threshold vs. Temperature.
7.0
LINE-SENSE Pin Voltage (V)
Figure 37. External Current Limit vs. Temperature
with RIL =12 kΩ.
1.2
0
Junction Temperature (°C)
Junction Temperature (°C)
K
1/04
75 100 125 150
1.2
Overvoltage Threshold
(Normalized to 25 °C)
PI-2872-051602
Current Limit
(Normalized to 25 °C)
1.0
28
50
Figure 36. Internal Current Limit vs. Temperature.
1.2
-50 -25
25
Junction Temperature (°C)
Figure 35. Frequency vs. Temperature.
0
-50 -25
0
PI-2865-051702
-50 -25
PI-2871-051502
Output Frequency
(Normalized to 25 °C)
1.2
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-200 -150 -100 -50
0
50 100 150 200 250
LINE-SENSE Pin Current (µA)
Figure 40. LINE-SENSE Pin Voltage vs. Current.
DPA423-426
-200 µA ≤ IX ≤ -25 µA
1.2
1.0
0.8
0.6
0.4
1.2
0.2
PI-2863-011904
1.4
VX = 1.375 - IXx 843 kΩ
CONTROL Pin Current
(Normalized to 25 °C)
EXTERNAL CURRENT LIMIT
Pin Voltage (V)
1.6
PI-2869-051502
Typical Performance Characteristics (cont.)
1.0
0.8
0.6
0.4
0.2
0
0
-225 -175
-125
-75
-25
-250
-200
-150
-100
-50
0
-50 -25
0
25
50
75 100 125 150
Junction Temperature (°C)
Figure 41. EXTERNAL CURRENT LIMIT Pin Voltage
vs. Current.
Figure 42. CONTROL Pin Current at Minimum Duty
Cycle vs. Temperature.
1.0
0.8
0.6
0.4
0.2
5.0
VC = 5 V
4.5
CONTROL Pin
Charging Current (mA)
PI-2864-051702
Onset Threshold Current
(Normalized to 25 °C)
1.2
PI-2841-051502
EXTERNAL CURRENT LIMIT Pin Current (µA)
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
-50 -25
0
25
50
0.0
75 100 125 150
0
10
Junction Temperature (°C)
40
50
60
0.8
0.6
0.4
Figure 44. IC vs. DRAIN Voltage.
PI-176B-033001
1.1
Breakdown Voltage
(Normalized to 25 °C)
PI-2870-051502
Remote OFF DRAIN Supply Current
(Normalized to 25 °C)
1.0
30
DRAIN Voltage (V)
Figure 43. Max. Duty Cycle Reduction Onset Threshold
Current vs. Temperature.
1.2
20
1.0
0.2
0
-50 -20
0.9
0
25
50
75 100 125 150
Junction Temperature (°C)
Figure 45. Remote OFF DRAIN Supply Current
vs. Temperature.
-50 -25
0
25
50
75 100 125 150
Junction Temperature (°C)
Figure 46 Breakdown Voltage vs. Temperature.
K
1/04
29
DPA423-426
Typical Performance Characteristics (cont.)
Drain Current (A)
16
14
TCASE = 25 °C
12
10
8
TCASE = 100 °C
6
4
2.5
PI-2850-011904
Scaling Factors:
DPA423 = 0.18
DPA424 = 0.36
DPA425 = 0.72
DPA426 = 1.00
On-resistance
(Normalized to 25 °C)
18
PI-2849-050302
20
2
1.5
1
0.5
2
0
0
1
2
3
4
-50 -25
5
Figure 47 Output Characteristics.
PI-2851-011904
Scaling Factors:
DPA423 = 0.18
DPA424 = 0.36
DPA425 = 0.72
DPA426 = 1.00
1000
100
10
0
20
40
60
80 100 120 140 160
DRAIN Voltage (V)
Figure 49. COSS vs. DRAIN Voltage.
30
K
1/04
25
50
75 100 125 150
Figure 48. On-resistance vs. Temperature.
Switching Loss (Watts) at 400 kHz
Capacitance (pF)
10000
0
Temperature (°C)
Drain Voltage (V)
2.5
2
PI-2877-052802
0
Data taken from a typical
forward converter design.
1.5
1
Scaling Factors:
DPA423 = 0.08
DPA424 = 0.20
DPA425 = 0.55
DPA426 = 1.00
0.5
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
In-Circuit Peak Drain Current Normalized to
Nominal Device Internal Current Limit
Figure 50. Typical Switching Loss.
DPA423-426
PART ORDERING INFORMATION
DPA-Switch Product Family
Series Number
G
Plastic Surface Mount DIP
P
Plastic DIP
R
Plastic TO-263-7C (available only with TL option)
(423, 424 & 425 only)
Package/Lead Options
DPA 423 G - TL
TL
Tape & Reel, (G Package: 1000 min., R Package: 750 min.)
K
1/04
31
DPA423-426
DIP-8
DIM
inches
D S .004 (.10)
mm
8
A
B
C
G
H
J1
J2
K
L
M
N
P
Q
0.367-0.387
0.240-0.260
0.125-0.145
0.015-0.040
0.120-0.140
0.057-0.068
0.014-0.022
0.008-0.015
0.100 BSC
0.030 (MIN)
0.300-0.320
0.300-0.390
0.300 BSC
5
-E-
9.32-9.83
6.10-6.60
3.18-3.68
0.38-1.02
3.05-3.56
1.45-1.73
0.36-0.56
0.20-0.38
2.54 BSC
0.76 (MIN)
7.62-8.13
7.62-9.91
7.62 BSC
B
1
4
-D-
A
M
J1
Notes:
1. Package dimensions conform to JEDEC
specification MS-001-AB for standard dual in-line
(DIP) package .300 inch row spacing
(PLASTIC) 8 leads (issue B, 7/85).
2. Controlling dimensions are inches.
3. Dimensions shown do not include mold flash
G
or other protrusions. Mold flash or
protrusions shall not exceed .006 (.15) on any
side.
L
4. D, E and F are reference datums on the molded
body.
N
C
-FH
K
Q
J2
P08A
P
PI-2076-101102
SMD-8
D S .004 (.10)
8
-E-
1
E S .010 (.25)
P
B
.420
.046 .060
.080
.086
.186
.286
-D-
A
M
.060 .046
Pin 1
4
L
Solder Pad Dimensions
J1
C
K
-F.004 (.10)
J3
J4
G08A
DIM
inches
mm
A
B
C
G
H
J1
J2
J3
J4
K
L
M
P
α
0.367-0.387
0.240-0.260
0.125-0.145
0.004-0.012
0.036-0.044
0.057-0.068
0.048-0.053
0.032-0.037
0.007-0.011
0.010-0.012
0.100 BSC
0.030 (MIN)
0.372-0.388
0-8°
9.32-9.83
6.10-6.60
3.18-3.68
0.10-0.30
0.91-1.12
1.45-1.73
1.22-1.35
0.81-0.94
0.18-0.28
0.25-0.30
2.54 BSC
0.76 (MIN)
9.45-9.86
0-8°
5
J2
.010 (.25) M A S
α
G
H
Notes:
1. Package dimensions conform to JEDEC
specification MS-001-AB (issue B, 7/85)
except for lead shape and size.
2. Controlling dimensions are inches.
3. Dimensions shown do not include mold
flash or other protrusions. Mold flash or
protrusions shall not exceed .006 (.15) on
any side.
4. D, E and F are reference datums on the
molded body.
PI-2077-041003
32
K
1/04
DPA423-426
TO-263-7C
.390 (9.91)
.420 (10.67)
.245 (6.22)
min.
.045 (1.14)
.055 (1.40)
.055 (1.40)
.066 (1.68)
.326 (8.28)
.336 (8.53)
.580 (14.73)
.620 (15.75)
.225 (5.72)
min.
.208 (5.28)
Ref.
-ALD #1
.024 (0.61)
.034 (0.86)
.100 (2.54)
Ref.
.050 (1.27)
.000 (0.00)
.010 (0.25)
.090 (2.29)
.110 (2.79)
.010 (0.25)
.012 (0.30)
.024 (0.61)
0°- 8°
.315 (8.00)
.380 (9.65)
Solder Pad
Dimensions
.165 (4.19)
.185 (4.70)
.004 (0.10)
.638 (16.21)
.128 (3.25)
.050 (1.27)
.038 (0.97)
Notes:
1. Package Outline Exclusive of Mold Flash & Metal Burr.
2. Package Outline Inclusive of Plating Thickness.
3. Foot Length Measured at Intercept Point Between
Datum A Lead Surface.
R07C
4. Controlling Dimensions are in Inches. Millimeter
Dimensions are shown in Parentheses.
PI-2664-112702
K
1/04
33
DPA423-426
34
K
1/04
DPA423-426
Revision Notes
Date
F
1) Final release data sheet.
6/02
G
2) Updated Figure 25 and text description.
9/02
H
1)
2)
3)
4)
4/03
I
1) Corrected text errors on pp. 1, 7 and 20.
5/03
J
1) Figure 25 and description in text updated.
5/03
K
1) Added P and G packages.
1/04
Corrected missing text on page 9 and corrected Table 4.
Updated R package description.
Revised thermal impedances (θJA), DCMIN, VF, IF, and BVDSS.
Updated Figure 25 and description in text.
K
1/04
35
DPA423-426
For the latest updates, visit our Web site: www.powerint.com
PATENT INFORMATION
Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume
any liability arising from the use of any device or circuit described herein, nor does it convey any license under its patent rights or the rights of others.
The products and applications illustrated herein (including circuits external to the products and transformer construction) may be covered by one or more U.S.
and foreign patents or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations’ patents
may be found at www.powerint.com.
LIFE SUPPORT POLICY
POWER INTEGRATIONS' PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein:
1. Life support devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when
properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
The PI logo, TOPSwitch, TinySwitch, LinkSwitch and EcoSmart are registered trademarks of Power Integrations.
PI Expert and DPA-Switch are trademarks of Power Integrations. ©Copyright 2004, Power Integrations
WORLD HEADQUARTERS
Power Integrations
5245 Hellyer Avenue
San Jose, CA 95138, USA.
Main: +1-408-414-9200
Customer Service:
Phone: +1-408-414-9665
Fax: +1-408-414-9765
e-mail: [email protected]
CHINA (SHENZHEN)
Power Integrations
International Holdings, Inc.
Rm# 1705, Bao Hua Bldg.
1016 Hua Qiang Bei Lu
Shenzhen Guangdong,
518031, China
Phone: +86-755-8367-5143
Fax: +86-755-8377-9610
e-mail: [email protected]
ITALY
Power Integrations S.r.l.
Via Vittorio Veneto 12,
Bresso
Milano, 20091, Italy
Phone: +39-028-928-6001
Fax: +39-028-928-6009
e-mail: [email protected]
SINGAPORE (ASIA PACIFIC
HEADQUARTERS)
Power Integrations, Singapore
51 Newton Road
#15-08/10 Goldhill Plaza
Singapore, 308900
Phone: +65-6358-2160
Fax: +65-6358-2015
e-mail: [email protected]
AMERICAS
Power Integrations
4335 South Lee Street, Suite G
Buford, GA 30518, USA
Phone: +1-678-714-6033
Fax: +1-678-714-6012
e-mail: [email protected]
GERMANY
Power Integrations GmbH
Rueckertstrasse 3
D-80336, Muenchen, Germany
Phone: +49-89-5527-3910
Fax: +49-89-5527-3920
e-mail: [email protected]
JAPAN
Power Integrations, K.K.
Keihin-Tatemono 1st Bldg.
12-20 Shin-Yokohama
2-Chome,
Kohoku-ku, Yokohama-shi,
Kanagawa 222-0033, Japan
Phone: +81-45-471-1021
Fax: +81-45-471-3717
e-mail: [email protected]
TAIWAN
Power Integrations
International Holdings, Inc.
5F-1, No. 316, Nei Hu Rd., Sec. 1
Nei Hu Dist.
Taipei, Taiwan 114, R.O.C.
Phone: +886-2-2659-4570
Fax: +886-2-2659-4550
e-mail: [email protected]
CHINA (SHANGHAI)
Power Integrations
International Holdings, Inc.
Rm 807, Pacheer
Commercial Centre
555 Nanjing West Road
Shanghai, 200041, China
Phone: +86-21-6215-5548
Fax: +86-21-6215-2468
e-mail: [email protected]
INDIA (TECHNICAL SUPPORT)
Innovatech
261/A, Ground Floor
7th Main, 17th Cross,
Sadashivanagar
Bangalore 560080
Phone: +91-80-5113-8020
Fax: +91-80-5113-8023
e-mail: [email protected]
KOREA
Power Integrations
International Holdings, Inc.
8th Floor, DongSung Bldg.
17-8 Yoido-dong,
Youngdeungpo-gu,
Seoul, 150-874, Korea
Phone: +82-2-782-2840
Fax: +82-2-782-4427
e-mail: [email protected]
APPLICATIONS HOTLINE
World Wide +1-408-414-9660
APPLICATIONS FAX
World Wide +1-408-414-9760
UK (EUROPE & AFRICA
HEADQUARTERS)
Power Integrations (Europe) Ltd.
1st Floor, St. James’s House
East Street
Farnham
Surrey
GU9 7TJ
United Kingdom
Phone: +44 (0) 1252-730-140
Fax: +44 (0) 1252-727-689
e-mail: [email protected]
36
K
1/04